A Favard type theorem for orthogonal polynomials on the unit circle from a three term recurrence formula

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Modelagem e otimização por metodologia de superfícies de resposta: um estudo em arames de aço SAE 9254 para molas automobilísticas

Pós-graduação em Engenharia Mecânica - FEG

Hot turning of a difficult-to-machine steel (sae xev-f) aided by infrared radiation

A possible way for increasing the cutting tool life can be achieved by heating the workpiece in order to diminish the shear stress of material and thus decrease the machining forces. In this study, quartz electrical resistances were set around the workpiece for heating it during the turning. In the tests, heat-resistant austenitic alloy steel was used, hardenable by precipitation, mainly used in combustion engine exhaustion valves, among other special applications for industry. The results showed that in the hot machining the cutting tool life can be increased by 340% for the highest cutting speed tested and had a reduction of 205% on workpiece surface roughness, accompanied by a force decrease in relation to conventional turning. In addition, the chips formed in hot turning exhibited a stronger tendency to continuous chip formation indicating less energy spent in material removal process. Microhardness tests performed in the workpieces subsurface layers at 5 m depth revealed slightly higher values in the hot machining than in conventional, showing a tendency toward the formation of compressive residual stress into plastically deformed layer. The hot turning also showed better performance than machining using cutting fluid. Since it is possible to avoid the use of cutting fluid, this machining method can be considered better for the environment and for the human health.

Desenvolvimento de um computador de bordo para veículo Baja-SAE

The objective of this paper is show the development of an Eletronic Control Unit (ECU) for Baja-SAE vehicles from its requirements to final implementation. An ECU for Baja-SAE vehicles is made of electric and electronic circuits (appropriated to the hostile situations of an off-road competition) able to make important measurements for the running or stand-by vehicle performance. For this development, some concepts were studied: embedded electronics concepts (mainly microcontrollers and data acquisition circuits) and sensoring. Both the studies were made considering the off-road environment. After these initial studies, the elaboration of the basics hardware and software (under simulations) has begun, and this elaboration objectives maximum performance and low implementation cost. After the theorical studies, basic definition of the hardware and software’s architectures and simulations, the printed circuit boards (PCB) were made, as exhaustive tests in these boards for debugging and verify if the boards work well. Once the system was tested in the university, it ran into a regional Southeast competition in 2010, that definitely proved the efficiency of the whole system

Influências do Projeto Baja SAE no ensino da engenharia e no desenvolvimento do aluno

This work aims to show the importance of Baja SAE Project in engineering education, as well as the development of the student, being an outstanding tool for the engineering student has an education that meets the objectives of the pedagogical university and also the guidelines Ministry of Education curriculum for engineering courses. The Baja SAE Project provides the engineering students the chance to apply in practice the knowledge acquired in the classroom, to enhance their preparation for the labor market. The student becomes involved with a real case of project development, from concept design, detailed design and construction. The Baja SAE Project redefines the position of the student as an active element in the learning process engineering, leaving behind the simple condition of receiving information. Values procedures that provide students the opportunity to learn in contexts of professional practice, while offering the opportunity to contextualize the execution of a project. From an analysis to develop personal skills, Baja SAE Project has its own characteristics and essential for professional practice, however, not specific to the engineering course. For example, capacity for teamwork, communication skills written and oral, ethical behavior, critical, overview, entrepreneurial spirit, leadership, etc

Redução de empeno em barra trefiladas do aço SAE 9254

In this paper we study the process of manufacture of wire drawn steel bars 9254, from rolled wire rod. These bars are used in the automotive industry for the manufacture of coil springs, which make up the system damping of several vehicles. The wire drawing process consists of the steps of pre-straightening, shot peening, drawing, cutting and polishing. The study aims to search for the configuration of process variables, which present the best result with respect to bending. To this were maintained settings prestraightening and mechanical stripping and varied angles and stringer polish being studied to replace the spinneret with a working angle, for a string with two working angles. To assist in the analysis of the results was the tool used DOE Software Minitab, which assesses the variation in results according to each parameter and the interaction parameters. It was thus possible to determine the best condition for wire drawing

Estudo das propriedades mecânicas do aço SAE 1312 modificado ao nióbio

The study of mechanical properties of high-alloy special steels is of great interest of the steel industry due to the great demand by companies that manufacture automotive components of high criticality, and also because of its high commercial value. However, the development of this type of alloy metals demand highly technical knowledge. Among these extremely important kinds of steel, the subject which is the interest of this study is the special steel modified by niobium. The manganese and niobium are the main alloying elements in the composition of these steels, both of them increase the stability of the austenite region, however, manganese increases the hardenability and tensile yield strength, and niobium increases the mechanical strength and promotes refining the grain. The mechanical characterization of steel SAE 1312 modified the niobium was made in order to gain a better understanding of the influence on the mechanical properties caused by aging at different temperatures and for different reductions in the drawing of gauge material. This characterization was made by means of tensile test and hardness. This material showed an increase in yield strength and hardness when gauge with large reductions during the wiredrawing, but when subjected to aging temperatures higher than 300 ° C had a slight loss of these properties

Processamento de peças em materiais compósitos para o projeto BAJA SAE

The weight of a vehicle has always been considered an extreme important factor, because it interferes in the performance, steering, consume, environmental impact, wear of components, among the others. Because of the new demand, consume reduction aim and gases emission increased the necessity to manufacture lighter vehicles, guaranteeing the complying with the gas emission international law. Besides the legal demand, the low weight will certainly be essential for the competitiveness for the next generation of vehicles. It is with this thinking the composite materials have been introduced in the automobilist industry, because those materials show an excellent relation of strength/weight, providing a reduction of consume and the increase of load capacity. Those factors justify the increase of interest of industry and the necessity of optimization of those materials and of their process. For this research, the field of application will be the Baja SAE Project, a project that is fully developed by engineering students, where they build a prototype single seat, off-road category, for use on hilly slopes with obstacle. This research aims to study two key components of the prototype are made of composite materials, analyzing all the processing. In addition, there is the analysis of the viability of this production parts to a Baja SAE vehicle, in order to increase their performance and reduce their weight without reducing the safety and robustness of the prototype. It was possible to achieve weight reduction of the steering subsystem with manufacturing the flywheel hybrid composite (carbon/glass) and the replacement of SAE 1010 steel by hybrid composite (carbon/aramid) in CVT box. The importance of this study is to obtain a good project for the vehicle of technical and scientific manner, contributing to the know-how to the team and providing a basis for optimization for upcoming projects

Influência da adição do nióbio no comportamento mecânico e microestrutural do aço SAE 6150

Pós-graduação em Engenharia Mecânica - FEG

A influência da temperatura de pré-aquecimento e tecimento na microestrutura e propriedades mecânicas na soldagem MIG/MAG robotizada de aços SAE 8620 com ABNT LN28

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de uma caixa de redução para veículo Baja SAE

A gear Box in a Baja SAE vehicle is required due to the objectives of the SAE competitions, which the vehicles are challenged to pass through different obstacles. A powertrain system has as the main objective the extension of the torque for the traction shaft of the vehicle, when compared to that one available in the engine. The Objective of this thesis is the description of a gear box project for a Baja SAE vehicle of the Piratas do Vale Team of Unesp Guaratinguetá. In the development of the thesis, a flowchart, developed by the team, was used, which includes a theory part and also the choice of shelf components. In this Project, the type of gearbox was chosen, besides the calculation of axles, gears, bearings and sealers, and software simulations were done for the critical parts. The transmission, developed in this thesis, is more complex than the current one used by the team, but the new one shows improvements, as a new reverse gear with high torque

Desenvolvimento de uma caixa de redução para veículo Baja SAE

A gear Box in a Baja SAE vehicle is required due to the objectives of the SAE competitions, which the vehicles are challenged to pass through different obstacles. A powertrain system has as the main objective the extension of the torque for the traction shaft of the vehicle, when compared to that one available in the engine. The Objective of this thesis is the description of a gear box project for a Baja SAE vehicle of the Piratas do Vale Team of Unesp Guaratinguetá. In the development of the thesis, a flowchart, developed by the team, was used, which includes a theory part and also the choice of shelf components. In this Project, the type of gearbox was chosen, besides the calculation of axles, gears, bearings and sealers, and software simulations were done for the critical parts. The transmission, developed in this thesis, is more complex than the current one used by the team, but the new one shows improvements, as a new reverse gear with high torque

Consistency of the mass variation formula for black holes accreting cosmological fluids

We address the spherical accretion of generic fluids onto black holes. We show that, if the black hole metric satisfies certain conditions, in the presence of a test fluid it is possible to derive a fully relativistic prescription for the black hole mass variation. Although the resulting equation may seem obvious due to a form of it appearing as a step in the derivation of the Schwarzschild metric, this geometrical argument is necessary to fix the added degree of freedom one gets for allowing the mass to vary with time. This result has applications on cosmological accretion models and provides a derivation from first principles to serve as a basis to the accretion equations already in use in the literature.

Dahlberg formula: a novel approach for its evaluation

INTRODUCTION: The accurate evaluation of error of measurement (EM) is extremely important as in growth studies as in clinical research, since there are usually quantitatively small changes. In any study it is important to evaluate the EM to validate the results and, consequently, the conclusions. Because of its extreme simplicity, the Dahlberg formula is largely used worldwide, mainly in cephalometric studies. OBJECTIVES: (I) To elucidate the formula proposed by Dahlberg in 1940, evaluating it by comparison with linear regression analysis; (II) To propose a simple methodology to analyze the results, which provides statistical elements to assist researchers in obtaining a consistent evaluation of the EM. METHODS: We applied linear regression analysis, hypothesis tests on its parameters and a formula involving the standard deviation of error of measurement and the measured values. RESULTS AND CONCLUSION: we introduced an error coefficient, which is a proportion related to the scale of observed values. This provides new parameters to facilitate the evaluation of the impact of random errors in the research final results.