Ultra-dry oxygen atmosphere to protect tellurite glass fiber from surface crystallization

In this study we report on surface crystallization phenomena and propose a solution for the fabrication of long and robust tellurite glass fibers. The bulk tellurite glasses of interest were prepared by melting and quenching techniques. Tellurite glass preforms and fibers were fabricated by suction casting and rod-in-tube drawing methods, respectively. The surfaces of the tellurite bulk glass samples and of the drawn fibers prepared under different controlled atmospheres were examined by X-ray diffraction. When the tellurite glass fibers were drawn in ambient air containing water vapor, four primary kinds of small crystals were found to appear on the fiber surface, alpha-TeO(2), gamma-TeO(2), Zn(2)Te(3)O(8) and Na(2)Zn(3)(CO(3))(4)center dot 3H(2)O. A mechanism for this surface crystallization is proposed and a solution described, using an ultra-dry oxygen gas atmosphere to effectively prevent surface crystallization during fiber drawing. (C) 2010 Elsevier B.V. All rights reserved.

Composition Optimization of Tellurite Glass for Low-Loss and Robust Fiber Fabrication

低损耗高强度碲酸盐玻璃光纤用光学材料的优化方案

Single-Mode Solid-Core Tellurite Glass Fiber with Large Mode Area and Low Loss for Infrared Applications

低损耗实芯碲酸盐光纤的非线性研究

Chirped fiber Bragg gratings for optical fiber dispersion compensation

The use of alpha-power chirped fiber Bragg gratings for dispersion cancellation in an optical fiber link is discussed. Numerical and theoretical investigation of recompressing the dispersion-broadened pulse by using alpha-power chirped gratings is made, which shows that, the dispersion-broadened Gaussian pulse after 100 km standard fiber (with zero dispersion at lambda = 1.3 mu m) trnasmission at lambda = 1.55 mu m with initial width of T-FWHM = 33ps (full width at half maximum) can be perfectly recompressed with the peak reflectivity of 82% by using a 30 mm long alpha-power chirped fiber grating with proper a value and optimal grating parameters.

A High-Efficiency Fiber-to-Waveguide Coupler with Low Polarization Dependence Using a Diluted Waveguide in InP Substrate with a 1.55μm Wavelength

We propose a fiber-to-waveguide coupler for side-illuminated p-i-n photodiodes to obtain high responsivity and low polarization dependence that is grown on InP substrate and is suitable for surface hybrid integration in low cost modules. The fiber-to-waveguide coupler is based on a diluted waveguide,which is composed of ten periods of undoped 120nm InP/80nm InGaAsP （1.05μm bandgap） multiple layers. Using the semi-vectorial three dimensional beam propagation method （BPM） with the central difference scheme,the coupling efficiency of fiber-to-waveguide under different conditions is simulated and studied,and the optimized conditions for fiber-to-waveguide coupling are obtained. For TE-like and TM-like modes,the calculated maximum coupling efficiency is higher than 94% and 92% ,respectively. The calculated polarization dependence is less than 0. ldB,showing good polarization independence.

808-nm fiber coupled module with a CW output power up to 130 W

A fiber coupled module is fabricated with integrating the emitting light from four laser diode bars into multimode fiber bundle. The continuous wave (CW) output power of the module is about 130 W with a coupling efficiency of around 80%. The output power is very stable after the temperature cycling and vibration test. No apparent power decrease has been observed as the device working continuously for 500 h.

Electro-Optical Effect Measurement of Thin-Film Material Using PM Fiber Mach-Zehnder Interferometer

A polarization-maintaining (PM) fiber Mach-Zehnder (MZ) interferometer has been established to measure the EO effect of very thin film materials with optical anisotropy. Unlike a common MZ interferometer,all the components are connected via polarization-maintaining fibers. At the same time, a polarized DFB laser with a maximum power output of 10mW is adopted as the light source to induce a large extinction ratio. Here, we take it to determine the electro-optical coefficients of a very thin superlattice structure with GaAs, KTP, and GaN as comparative samples. The measured EO coefficients show good comparability with the others.

4-W single transverse mode Yb3+-doped fiber laser pumped by 915-nm laser diode array

A cladding-pumped ytterbium-doped fiber laser is described in this letter. Using unusual pumping source with 915-nm wavelength, slope efficiency up to 75% with respect to absorbed input power and output power is obtained, a maximum output power of 4.006 W with fundamental mode is measured.

Theoretical Study on the Butt-coupling of Semiconductor Laser and Fiber Bragg Grating

The butt-coupling between a semiconductor laser diode and a fiber Bragg grating external cavity acts a key roll on the laser characteristics. The scatter matrix method considering the butt-coupling efficiency is used to analyze the butt-coupling between them. It is found that the butt-coupling distance and coupling efficiency determine the laser characteristics. For strong feedback, the single lasing wavelength changes in the reflection bandwidth of the effective reflectivity ( approximately the Bragg region of the fiber Bragg grating) as the distances change. For weak feedback condition, some different results are obtained. The SMSRs in the two conditions are presented and analyzed. These results can provide important design guidance of device parameters for the practical fabrication.