Guide for fabricating and installing shallow ground water observation wells /

"January 2001."

Effect of pumping from a shallow well on the ground-water table /

Mode of access: Internet.

Shallow ground-water flow and drainage characteristics of the Brown Ditch basin near the East Unit, Indiana Dunes National Lakeshore, Indiana, 1982 /

Mode of access: Internet.

A composite DOP approach to excluding bottom reflectance in mapping water parameters of shallow coastal zones from TM imagery

In this paper we proposed a composite depth of penetration (DOP) approach to excluding bottom reflectance in mapping water quality parameters from Landsat thematic mapper (TM) data in the shallow coastal zone of Moreton Bay, Queensland, Australia. Three DOPs were calculated from TM1, TM2 and TM3, in conjunction with bathymetric data, at an accuracy ranging from +/-5% to +/-23%. These depths were used to segment the image into four DOP zones. Sixteen in situ water samples were collected concurrently with the recording of the satellite image. These samples were used to establish regression models for total suspended sediment (TSS) concentration and Secchi depth with respect to a particular DOP zone. Containing identical bands and their transformations for both parameters, the models are linear for TSS concentration, logarithmic for Secchi depth. Based on these models, TSS concentration and Secchi depth were mapped from the satellite image in respective DOP zones. Their mapped patterns are consistent with the in situ observed ones. Spatially, overestimation and underestimation of the parameters are restricted to localised areas but related to the absolute value of the parameters. The mapping was accomplished more accurately using multiple DOP zones than using a single zone in shallower areas. The composite DOP approach enables the mapping to be extended to areas as shallow as <3 m. (C) 2004 Elsevier Inc. All rights reserved.

Shallow landslide prediction in the Serra do Mar, Sao Paulo, Brazil

Various methods are currently used in order to predict shallow landslides within the catchment scale. Among them, physically based models present advantages associated with the physical description of processes by means of mathematical equations. The main objective of this research is the prediction of shallow landslides using TRIGRS model, in a pilot catchment located at Serra do Mar mountain range, Sao Paulo State, southeastern Brazil. Susceptibility scenarios have been simulated taking into account different mechanical and hydrological values. These scenarios were analysed based on a landslide scars map from the January 1985 event, upon which two indexes were applied: Scars Concentration (SC - ratio between the number of cells with scars, in each class, and the total number of cells with scars within the catchment) and Landslide Potential (LP - ratio between the number of cells with scars, in each class, and the total number of cells in that same class). The results showed a significant agreement between the simulated scenarios and the scar's map. In unstable areas (SF <= 1), the SC values exceeded 50% in all scenarios. Based on the results, the use of this model should be considered an important tool for shallow landslide prediction, especially in areas where mechanical and hydrological properties of the materials are not well known.

Osmoregulative capacity in birdseed millet under conditions of water stress. I. Variation in Setaria italica and Panicum miliaceum

Experiments involving 14 accessions of Panicum miliaceum L. (Proso millet) and 11 accessions of Setaria italica L. (Foxtail millet) have demonstrated variability in the degree of osmoregulative capacity among these accessions. Birdseed millet is generally claimed to be sensitive to drought stress, apparently because of a shallow root system. Accessions with high osmoregulative capacity demonstrate at least some drought tolerance. Osmoregulative capacity was measured on flag leaves of headed millet plants in pots undergoing water stress in a controlled environment chamber. Osmoregulative capacity was determined from the relationship between osmotic potential and leaf water potential; and the logarithmic relationship between osmotic potential and relative water content. The group of accessions of S. italica showed an overall level of osmoregulative capacity which was greater than that observed for the group of P. miliaceum accessions. Four accessions of S. italica (108042, 108463, 108541 and 108564) and one accession of P. miliaceum (108104) demonstrated high osmoregulative capacity. Differences of 1.05 MPa or more between observed and estimated osmotic potential were found at relative water contents of 80 % among these accessions. The extent of osmoregulative capacity was associated with osmotic potential at full turgor and the rate of decline in osmotic potential as leaf water potentail declined.

Water table waves in an unconfined aquifer: Experiments and modeling

[1] Comprehensive measurements are presented of the piezometric head in an unconfined aquifer during steady, simple harmonic oscillations driven by a hydrostatic clear water reservoir through a vertical interface. The results are analyzed and used to test existing hydrostatic and nonhydrostatic, small-amplitude theories along with capillary fringe effects. As expected, the amplitude of the water table wave decays exponentially. However, the decay rates and phase lags indicate the influence of both vertical flow and capillary effects. The capillary effects are reconciled with observations of water table oscillations in a sand column with the same sand. The effects of vertical flows and the corresponding nonhydrostatic pressure are reasonably well described by small-amplitude theory for water table waves in finite depth aquifers. That includes the oscillation amplitudes being greater at the bottom than at the top and the phase lead of the bottom compared with the top. The main problems with respect to interpreting the measurements through existing theory relate to the complicated boundary condition at the interface between the driving head reservoir and the aquifer. That is, the small-amplitude, finite depth expansion solution, which matches a hydrostatic boundary condition between the bottom and the mean driving head level, is unrealistic with respect to the pressure variation above this level. Hence it cannot describe the finer details of the multiple mode behavior close to the driving head boundary. The mean water table height initially increases with distance from the forcing boundary but then decreases again, and its asymptotic value is considerably smaller than that previously predicted for finite depth aquifers without capillary effects. Just as the mean water table over-height is smaller than predicted by capillarity-free shallow aquifer models, so is the amplitude of the second harmonic. In fact, there is no indication of extra second harmonics ( in addition to that contained in the driving head) being generated at the interface or in the interior.

Environmental impact on the bacteriological quality of domestic water supplies in Lagos, Nigeria

OBJECTIVE: To assess the impact of town planning, infrastructure, sanitation and rainfall on the bacteriological quality of domestic water supplies. METHODS: Water samples obtained from deep and shallow wells, boreholes and public taps were cultured to determine the most probable number of Escherichia coli and total coliform using the multiple tube technique. Presence of enteric pathogens was detected using selective and differential media. Samples were collected during both periods of heavy and low rainfall and from municipalities that are unique with respect to infrastructure planning, town planning and sanitation. RESULTS: Contamination of treated and pipe distributed water was related with distance of the collection point from a utility station. Faults in pipelines increased the rate of contamination (p<0.5) and this occurred mostly in densely populated areas with dilapidated infrastructure. Wastewater from drains was the main source of contamination of pipe-borne water. Shallow wells were more contaminated than deep wells and boreholes and contamination was higher during period of heavy rainfall (p<0.05). E. coli and enteric pathogens were isolated from contaminated supplies. CONCLUSIONS: Poor town planning, dilapidated infrastructure and indiscriminate siting of wells and boreholes contributed to the low bacteriological quality of domestic water supplies. Rainfall accentuated the impact.

Diet of Cnesterodon decemmaculatus (Poeciliidae) and Jenynsia multidentata (Anablepidae) in a hypertrophic shallow lake of Uruguay

Diet of Cnesterodon decemmaculatus (Jenyns, 1842) and Jenynsia multidentata (Jenyns, 1842) were analysed in Lake Rodó, an urban hypertrophic lake from Montevideo, Uruguay. Both species displayed omnivory. The most consumed items for C. decemmaculatus were zooplankton, periphyton, phytoplankton and detritus; the diet of J. multidentata included zooplankton, insects, crustaceans and juvenile fish. Our results suggest that both species could be acting as facultative planktivores. The fish community of this lake is characterised by the dominance of C. decemmaculatus and J. multidentata. Under this condition, predation on large-bodied zooplankton could indirectly be contributing to maintain a high phytoplankton abundance and a low water transparency.

Geochemistry of highly acidic mine water following disposal into a natural lake with carbonate bedrock

Acid mine drainage (AMD) from the Zn-Pb(-Ag-Bi-Cu) deposit of Cerro de Pasco (Central Peru) and waste water from a Cu-extraction plant has been discharged since 1981 into Lake Yanamate, a natural lake with carbonate bedrock. The lake has developed a highly acidic pH of similar to 1. Mean lake water chemistry was characterized by 16,775 mg/L acidity as CaCO(3), 4330 mg/L Fe and 29,250 mg/L SO(4). Mean trace element concentrations were 86.8 mg/L Cu, 493 mg/L Zn, 2.9 mg/L Pb and 48 mg/L As, which did not differ greatly from the discharged AMD. Most elements showed increasing concentrations from the surface to the lake bottom at a maximal depth of 41 m (e.g. from 3581 to 5433 mg/L Fe and 25,609 to 35,959 mg/L SO(4)). The variations in the H and 0 isotope compositions and the element concentrations within the upper 10 m of the water column suggest mixing with recently discharged AMD, shallow groundwater and precipitation waters. Below 15 m a stagnant zone had developed. Gypsum (saturation index, SI similar to 0.25) and anglesite (SI similar to 0.1) were in equilibrium with lake water. Jarosite was oversaturated (SI similar to 1.7) in the upper part of the water column, resulting in downward settling and re-dissolution in the lower part of the water column (SI similar to -0.7). Accordingly, jarosite was only found in sediments from less than 7 m water depth. At the lake bottom, a layer of gel-like material (similar to 90 wt.% water) of pH similar to 1 with a total organic C content of up to 4.40 wet wt.% originated from the kerosene discharge of the Cu-extraction plant and had contaminant element concentrations similar to the lake water. Below the organic layer followed a layer of gypsum with pH 1.5, which overlaid the dissolving carbonate sediments of pH 5.3-7. In these two layers the contaminant elements were enriched compared to lake water in the sequence As < Pb approximate to Cu < Cd < Zn = Mn with increasing depth. This sequence of enrichment was explained by the following processes: (i) adsorption of As on Fe-hydroxides coating plant roots at low pH (up to 3326 mg/kg As), (ii) adsorption at increasing pH near the gypsum/calcite boundary (up to 1812 mg/kg Pb, 2531 mg/kg Cu. and 36 mg/kg Cd), and (iii) precipitation of carbonates (up to 5177 mg/kg Zn and 810 mg/kg Mn: all data corrected to a wet base). The infiltration rate was approximately equal to the discharge rate, thus gypsum and hydroxide precipitation had not resulted in complete clogging of the lake bedrocks. (C) 2010 Elsevier Ltd. All rights reserved.

Effect of irrigation water and processing on the microbial quality of lettuces produced and sold on markets in Dakar (Senegal)

The aim of this survey is to assess the microbiological impact of irrigation water on lettuces produced on two urban agricultural sites and sold on markets; 6 and 7%, respectively, of lettuces coming from the sites of Pikine and Patte d'Oie were Salmonella spp. positive. Lettuces irrigated with shallow groundwater (''Ceanes'' water) were more contaminated (8% at both Pikine and Patte d'Oie sites) compared to those irrigated with wastewater (4% at Pikine) or well water (5% at Patte d'Oie). As for the lettuces in marketplaces, their contamination seems to depend on the type of treatment occurring before sale. Lettuces previously washed in the ``Ceanes'' were more contaminated than those rinsed with tap water at the marketplace. Salmonella spp. have been isolated from all marketplaces. However, the rates of contamination in markets surrounding Patte d'Oie are higher (9 and 11% at Grand Yoff and Dalifort) than those surrounding Pikine (4 and 2% at Zinc and Sham) or Rufisque, the control (2%). Our results confirm that the reuse of wastewater in irrigation is an alternative to animal manure. Its risk of microbial contamination can be significantly reduced by washing the vegetables with tap water before they are sold. Copyright (C) 2010 John Wiley & Sons, Ltd.

An experimental study on the shallow-level migmatization of ferrogabbros from the Fuerteventura Basal Complex, Canary Islands

Spectacular shallow-level migmatization of ferrogabbroic rocks occurs in a metamorphic contact aureole of a gabbroic pluton of the Tierra Mala massif (TM) on Fuerteventura (Canary Islands). In order to improve our knowledge of the low pressure melting behavior of gabbroic rocks and to constrain the conditions of migmatization of the TM gabbros, we performed partial melting experiments on a natural ferrogabbro, which is assumed as protolith of the migmatites. The experiments were performed in an internally heated pressure vessel (IHPV) at 200 MPa, 930-1150 degreesC at relatively oxidizing conditions. Distinct amounts of water were added to the charge. From 930 to 1000 degreesC, the observed experimental phases are plagioclase (An(60-70)), clinopyroxene, amphibole (titanian magnesiohastingsites), two Fe-Ti oxides, and a basaltic, K-poor melt. Above 1000 degreesC, amphibole is no longer stable. The first melts are very rich in non-native plagioclase (>70 wt.%). This indicates that at the beginning of partial melting plagioclase is the major phase which is consumed to produce melt. In the experiments, plagioclase is stable up to high temperatures (1060 degreesC) showing increasing An content with temperature. This is not compatible with the natural migmatites, in which An-rich plagioclase is absent in the melanosomes, while amphibole is stable. Our results show that the partial melting of the natural rocks cannot be regarded as an ``in-situ'' process that occurred in a closed system. Considerable amounts of alkalis probably transported by water-rich fluids, derived from the mafic pluton underplating the TM gabbro, were necessary to drive the melting reaction out of the stability range of plagioclase. A partial melting experiment with a migmatite gabbro showing typical ``in-situ'' textures as starting material supports this assumption. Crystallization experiments performed at 1000 degreesC on a glass of the fitised ferrogabbro with different water contents added to the charge show that generally high water activities could be achieved (crystallization of amphibole), independently of the bulk water content, even in a system with very low initial bulk water content (0.3 wt.%). Increasing water contents produce plagioclase richer in An, reduces the modal proportion of plagioclase in the crystallizing assemblage and extends the melt fraction. High melt fractions of >30 wt.% could only be observed in systems with high bulk water contents (> - 2 wt.%). This indicates that the migmatites were generated under water-rich conditions (probably water-saturated), since those migmatites, which are characterized as ``in-situ'' formations, show generally high amounts of leucosomes (>30 wt.%). (C) 2003 Elsevier B.V. All rights reserved.

Limits on the validity of infinite length assumptions for modelling shallow landslides

The infinite slope method is widely used as the geotechnical component of geomorphic and landscape evolution models. Its assumption that shallow landslides are infinitely long (in a downslope direction) is usually considered valid for natural landslides on the basis that they are generally long relative to their depth. However, this is rarely justified, because the critical length/depth (L/H) ratio below which edge effects become important is unknown. We establish this critical L/H ratio by benchmarking infinite slope stability predictions against finite element predictions for a set of synthetic two-dimensional slopes, assuming that the difference between the predictions is due to error in the infinite slope method. We test the infinite slope method for six different L/H ratios to find the critical ratio at which its predictions fall within 5% of those from the finite element method. We repeat these tests for 5000 synthetic slopes with a range of failure plane depths, pore water pressures, friction angles, soil cohesions, soil unit weights and slope angles characteristic of natural slopes. We find that: (1) infinite slope stability predictions are consistently too conservative for small L/H ratios; (2) the predictions always converge to within 5% of the finite element benchmarks by a L/H ratio of 25 (i.e. the infinite slope assumption is reasonable for landslides 25 times longer than they are deep); but (3) they can converge at much lower ratios depending on slope properties, particularly for low cohesion soils. The implication for catchment scale stability models is that the infinite length assumption is reasonable if their grid resolution is coarse (e.g. >25?m). However, it may also be valid even at much finer grid resolutions (e.g. 1?m), because spatial organization in the predicted pore water pressure field reduces the probability of short landslides and minimizes the risk that predicted landslides will have L/H ratios less than 25. Copyright (c) 2012 John Wiley & Sons, Ltd.

Partial melting of basic dykes in the contact aureoles of two shallow-level, gabbro-pyroxenite intrusions, Fuerteventura

THESIS ABSTRACT Low-pressure anatexis of basic dykes gave rise to unusual, zebra-like migmatites, in the contact metamorphic aureoles of two layered gabbro-pyroxenite intrusions, PXl and PX2, in the root zone of an ocean island, Fuerteventura Basal Complex (Canary Islands). This thesis focuses on the understanding of processes attributing to the partial melting and formation of these migmatites, characterised by a dense network of closely spaced, millimetre-wide leucocratic segregations with perfectly preserved igneous textures. The presence of fluids are required to decrease the solidus of basic igneous lithologies, to allow partial melting in such aloes-pressure (1-2 kb) environment. An oxygen isotope study was thus carried out on dykes inside and beyond the PX2 aureole, in order to decipher the nature and origin of such fluids. Low or negative δ18O values were obtained for whole rocks and mineral-separates, decreasing towards the contact, with the intrusion itself retaining fairly high values. This trend has been attributed to the advection of meteoric water during magma emplacement, with increasing fluid/rock ratios (higher dyke intensities towards the intrusion acting as fluid-pathways) and higher temperatures promoting increasing exchange during recrystallisation. A comparison of whole rock and mineral major- and trace- element data allowed the redistribution of elements .between different mineral phases and generations, during contact metamorphism and partial melting to be assessed. Certain trace-elements, e.g. Zr, Hf, Y, and REEs, were internally redistributed during contact metamorphic recrystallisation, causing- the enrichment of neocrystallised diopsides compared to relict phenocrysts. This has been assigned to the liberation of trace elements on the breakdown of primary minerals, kaersutite and sphene, on entering the thermal aureole. Major and trace element compositions of minerals in migmatite melanosomes and leucosomes are almost identical, pointing to a syn- or post- solidus reequilibration on cooling of the migmatite terrain. The mineralogical, textural and geochemical evolution of dykes in a contact metamorphic aureole, is recorded around an apophysis of the PX1 intrusion, where there is evidence of incipient partial melting. Hydrothermal mineral pseudomorphs in the outer parts of the aureole are progressively replaced by dry mineral assemblages, with increasingly recrystallised diopside and evidence of partial melting -the extent of which varies from one lithology to another. The appearance of more mafic lithologies towards the intrusion, with lower whole rock SiO2 and mobile element abundances, e.g. Rb, Cs, K, has been explained by the migration and accumulation of feldspathic material into leucosomes outside the samples. A micro-structural study of leucosomes and leucocratic pods, with the aid of high-resolution X-ray computed micro-tomography (HRXµCT), allowing the visualization and quantification of shapes and orientations, was carried out in order to better understand the processes of melt segregation in the PX1 aureole. Leucocratic pods, representing former amygdales, are considered as natural strain ellipsoids. Their short axes are oriented perpendicular to leucosome planes, which sub-parallel the intrusive contact. Leucosomes thus effectively represent foliation planes. This implies that the direction of maximum shortening, during migmatisation, was perpendicular to the orientation of leucosomes, contradicting earlier models that suggest leucosomes represent tension veins. RESUME DE LA THESE Un phénomène rare de fusion partielle de filons basiques à basse pression a été étudié dans les auréoles de contact de deux intrusions litées de gabbro-pyroxénite, PX1 et PX2, localisées dans le soubassement de l'île volcanique de Fuerteventura aux Canaries. Cette anatexie a engendré des migmatites finement zébrées d'aspect très inhabituel, dont les processus de formation ont été étudiés dans le présent travail. Ces roches sont caractérisées par un réseau dense de veinules leucocrates d'épaisseur millimétrique, dont les textures ignées sont parfaitement préservées. La fusion partielle de roches basiques à basse pression (1-2 kbar) requiert la présence d'eau afin d'abaisser le solidus du système à des températures géologiquement réalistes. Une étude comparative des isotopes de l'oxygène a ainsi été menée sur des filons respectivement affectés et non affectés par le métamorphisme de contact, afin de confirmer la présence de ces fluides, de déterminer l'importance de leur interaction avec les roches et leur origine. Des valeurs de δ180 basses ou négatives ont été mesurées sur roche totale et minéraux séparés, décroissantes en direction du contact, alors que l'intrusion elle-même a conservé des valeurs élevées. Ce gradient a été attribué à l'advection d'eau météorique durant la mise en place du magma, les températures les plus élevées favorisant d'autant plus la circulation des fluides et les échanges isotopiques durant la recristallisation des roches. Cette recristallisation engendré une redistribution chimique complète des éléments entre les différentes générations de minéraux résultant du métamorphisme de contact et de l'anatexie, mise en évidence par microanalyse. Certains éléments traces comme Zr, Hf, Y et les REE ont été concentrés dans le diopside néoformé consécutivement à la déstabilisation de minéraux primaires riches en ces éléments comme la kaersutite ou le sphène. Les compositions en éléments majeurs et traces des minéraux des mélanosomes et leucosomes des migmatites sont pratiquement identiques, indiquant une rééquilibration syn- à postsolidus lors du refroidissement de l'auréole de contact. La transformation progressive des filons basiques au niveau de leur minéralogie, textures et composition chimique a pu être observée en détail à l'approche du contact d'une apophyse de l'intrusion PX1. La paragenèse magmatique initiale n'est jamais préservée, les faciès les plus distants du contact étant constitués d'un assemblage pseudomorphique hydrothermal. Ce dernier est progressivement remplacé par des assemblages anhydres incluant du diopside néoformé, puis apparaissent les premiers signes de fusion partielle, dont l'importance varie fortement d'une lithologie à l'autre. L'apparition de faciès plus basiques en direction du contact, avec des teneurs réduites en SiO2 et en éléments incompatibles tels Rb, Cs, K, a été attribuée à l'échappement de leucosomes feldspathiques hors du système. Une étude microstructurale de la distribution spatiale du matériel leucocrate au sein des migmatites par microtomographie X de haute résolution (HRXµCT) a été menée pour mieux comprendre les processus de ségrégation des liquides dans l'auréole de PX1. De petites entités ovoïdes, représentant d'anciennes structures amygdalaires au sein des filons, ont été considérées comme des ellipsoïdes marqueurs de la déformation finie. Leur petit axe est orienté perpendiculairement aux plans définis par les leucosomes, eux-mêmes subparallèles au contact intrusif. Les leucosomes matérialisent donc des plans de clivage. Ainsi, la direction de raccourcissement maximum durant la fusion partielle était perpendiculaire à l'orientation des leucosomes, contrairement à ce qui a été dit dans de précédentes publications, qui suggéraient que les leucosomes représentaient des veines de tension. RESUME DE LA THESE (POUR LE GRAND PUBLIC) L'observation directe du soubassement d'une île volcanique est une occasion rare, accessible dans le «complexe de base » de l'île canarienne de Fuerteventura. Ce dernier a enregistré divers phénomènes magmatiques, métamorphiques et de fusion partielle induits par l'intrusion répétée de magmas alimentant des appareils volcaniques sus jacents, sous forme de petits plutons, essaims de filons et complexes annulaires de gabbros alcalins, pyroxénites, syénites et carbonatites. Dans ce contexte de flux de chaleur élevé, des filons basiques ont subi une fusion partielle au contact de deux intrusions de gabbro-pyroxénite, un phénomène extrêmement rare à une profondeur aussi réduite, estimée à quelque 3-6 km. Les produits de cette fusion partielle sont des liquides très riches en feldspath, concentrés en un réseau dense de veinules blanches (leucosomes) au sein du matériau résiduel sombre non fondu (mélanosome) pour former ce qu'on appelle des migmatites. Outre les aspects pétrologiques liés à la formation de ces migmatites, l'intérêt majeur du phénomène réside dans le fait qu'il puisse représenter la source des magmas évolués parfois observés sur les îles océaniques. A des pressions aussi faibles que dans le soubassement de Fuerteventura (1-2 Kbar), la présence de fluides abondants est nécessaire pour abaisser la température de début de fusion des roches (solidus) à des valeurs géologiquement réalistes. Des expériences ont montré que même en présence de plusieurs %-poids d'eau, une température de 1000°C était encore nécessaire pour obtenir une proportion de liquide équivalente à celle observée sur le terrain, soit 25%. Or les magmas alcalins des îles océaniques, bien qu'hydratés, n'en contiennent de loin pas autant, ce qui implique une source d'eau externe. Une étude isotopique de l'oxygène a été entreprise afin de tester cette hypothèse. Les valeurs obtenues en 5180 sont basses ou négatives et indiquent l'influence d'eau d'origine météorique. Cette eau de pluie se serait infiltrée le long des filons depuis la surface du volcan et les aurait complètement hydrothermalisés en profondeur (situation encore visible à l'extérieur de l'auréole de contact), leur permettant ainsi de stocker l'eau nécessaire à leur fusion partielle ultérieure. L'interaction entre eau de pluie et filons a été d'autant plus importante que ces derniers étaient proches du contact avec l'intrusion, ce qui suggère que la circulation de ces eaux et leur interaction avec les roches a été favorisée par la chaleur fournie par l'intrusion elle-même. Un autre aspect de ce travail s'est focalisé sur la redistribution des éléments traces au sein des minéraux des filons basiques durant le métamorphisme de contact et la fusion partielle. Ainsi, le pyroxène de seconde génération est-il sensiblement enrichi en traces telles Zr, Hf, Y et les terres rares, par rapport au pyroxène magmatique originel, en relation avec la déstabilisation de minéraux primaires riches en ces éléments tels le sphène et la kaersutite. Cependant, les compositions en éléments majeurs et traces des minéraux recristallisés des migmatites sont pratiquement les mêmes dans les leucosomes et les mélanosomes, suggérant une rééquilibration chimique complète durant le refroidissement de ces lithologies. Si certaines migmatites se sont comportées en système chimiquement fermé (hormis l'eau météorique), d'autres filons ont manifestement perdu une partie de leurs leucosomes, ainsi qu'en témoigne leur composition progressivement appauvrie en silice et autres éléments incompatibles mobiles, tels K et Rb à l'approche du contact de l'intrusion. Parallèlement à cette évolution chimique, les paragenèses hydrothermales distantes du contact sont progressivement remplacées par des paragenèses anhydres, puis par l'apparition des premiers leucosomes, tandis que les textures magmatiques initiales sont complètement effacées au profit d'une combinaison de textures magmatique dans les leucosomes et en mosaïque dans les mélanosomes. Enfin, la distribution spatiale des liquides de fusion partielle a été étudiée par microtomographie X de haute résolution, dans des filons contenant des entités ovoïdes leucocrates, sans doute d'anciennes amygdales à zéolites. Ces dernières ont été considérées comme des ellipsoïdes de la déformation finie. L'orientation de leur petit axe, perpendiculaire au plan défini par les veinules de leucosomes, indique que ces derniers représentent des plans de clivage perpendiculaires à la direction de raccourcissement maximum. Ainsi, la ségrégation des liquides de fusion partielle se serait faite dans les plans de compression et non dans des plans de dilatation, contrairement à ce que laisserait penser le sens commun.

Shallow-platform palaeoenvironmental conditions recorded in deep-shelf sediments: C and stable isotopes in Upper Jurassic sections of southern Germany (Oxfordian-Kimmeridgian)

A high-resolution carbon and oxygen isotope analysis of Late Oxfordian-Early Kimmeridgian deep-shelf sediments of southern Germany is combined with investigation of nannofossil assemblage composition and sedimentological interpretations in order to evaluate the impact of regional palaeoenvironmental conditions on isotopic composition of carbonates. This study suggests that carbonate mud was essentially derived from the Jura shallow platform environments and also that the isotopic signature of carbonates deposited in the Swabian Alb deep shelf indirectly expresses the palaeoenvironmental evolution of the platform. Short-term fluctuations in delta(13) C and delta(18)O are probably controlled by changes in salinity (fresh-water input versus evaporation) in platform environments. Long-term fluctuations in carbon and oxygen isotope record throughout the Late Oxfordian-Early Kimmeridgian result from the interplay of increasing temperature and decreasing humidity, which both control the trophic level. Changes from mesotrophic to oligotrophic conditions in platform environments and in the deep-shelf surface waters are inferred. During the Late Oxfordian (Bimammatum Subzone to Planula Zone), the delta(13)C curve displays a positive shift of about 1 parts per thousand, which is comparable in intensity to global perturbations of the carbon cycle. This evident isotopic shift has not been documented yet in other basinal settings. It can be reasonably explained by local palaeoenvironmental changes on the Jura platform (salinity, temperature, and nutrient availability) that controlled platform carbonate production, and the geochemistry of overlying waters. However, increasing carbonate production on the Jura platform and related positive delta(13)C shifts recorded in the Swabian Alb deep shelf are the regional signatures of climatic changes affecting other palaeogeographical domains of Europe in which the carbonate production increased throughout the Late Oxfordian. (C) 2002 Elsevier Science B.V. All rights reserved.