The influence of particle shape on the stress-strain and creep response of a fine silica sand

The influence of particle shape on the stress-strain response of fine silica sand is investigated experimentally. Two sands from the same source and with the same particle size distribution were examined using Fourier descriptor analysis for particle shape. Their grains were, on average, found to have similar angularity but different elongation. During triaxial stress path testing, the stress-strain behavior of the sands for both loading and creep stages were found to be influenced by particle elongation. In particular, the behavior of the sand with less elongated grains was more like that of rounded glass beads during creep. The results highlight the role of particle shape in stress transmission in granular packings and suggest that shape should be taken more rigorously into consideration in characterizing geomaterials. © 2005 Taylor & Francis Group.

User responses to the learning demands of consumer products

Designers are typically male, under 35 years old and unimpaired. Users can be of any age and currently over 15% will have some form of impairment. As a result a vast array of consumer products suit youthful males and in many cases exclude other demographics (e.g. Keates and Clarkson, 2004). In studying the way a range of users learn how to use new products, key cognitive difficulties are revealed and linked back to the areas of the product causing the problems. The trials were structured so each user had to complete a specific set of tasks and were consistent across the user spectrum. The tasks set aimed to represent both everyday usage and less familiar functions. Whilst the knowledge gained could provide designers with valuable guidelines for the specific products examined, a more general abstraction provides knowledge of the pitfalls to avoid in the design of other product families.

Discrete element calculations of the impact of a sand column against rigid structures

Discrete particle simulations of column of an aggregate of identical particles impacting a rigid, fixed target and a rigid, movable target are presented with the aim to understand the interaction of an aggregate of particles upon a structure. In most cases the column of particles is constrained against lateral expansion. The pressure exerted by the particles upon the fixed target (and the momentum transferred) is independent of the co-efficient of restitution and friction co-efficient between the particles but are strongly dependent upon the relative density of the particles in the column. There is a mild dependence on the contact stiffness between the particles which controls the elastic deformation of the densified aggregate of particles. In contrast, the momentum transfer to a movable target is strongly sensitive to the mass ratio of column to target. The impact event can be viewed as an inelastic collision between the sand column and the target with an effective co-efficient of restitution between 0 and 0.35 depending upon the relative density of the column. We present a foam analogy where impact of the aggregate of particles can be modelled by the impact of an equivalent foam projectile. The calculations on the equivalent projectile are significantly less intensive computationally and yet give predictions to within 5% of the full discrete particle calculations. They also suggest that "model" materials can be used to simulate the loading by an aggregate of particles within a laboratory setting. © 2012 Elsevier Ltd. All rights reserved.

On the functions of products

Understanding the performance and manner of functioning of existing products is at the base of new product development activities. In engineering design the term function is generally used to refer to the technical actions performed by a product. However, products accomplish a wider range of goals. This research explores the opportunity to describe and model, through the concept of function, product actions across four dimensions including technical, aesthetic, social and economic. The research demonstrates that non-technical functions can be represented through active verbs and nouns and modelled using a method known as the Function Analysis Diagram (FAD). The research argues that when technical, aesthetic, social and economic perspectives on product development are considered as different types of function, stakeholders have a common language to communicate which can benefit design collaboration.

Dynamic centrifuge tests on shallow tunnel models in dry sand

In the framework of the Italian research project ReLUIS-DPC, a set of centrifuge tests were carried out at the Schofield Centre in Cambridge (UK) to investigate the seismic behaviour of tunnels. Four samples of dry sand were prepared at different densities, in which a small scale model of circular tunnel was inserted, instrumented with gauges measuring hoop and bending strains. Arrays of accelerometers in the soil and on the box allowed the amplification of ground motion to be evaluated; LVDTs measured the soil surface settlement. This paper describes the main results of this research, showing among others the evolution of the internal forces during the model earthquakes at significant locations along the tunnel lining. © 2010 Taylor & Francis Group, London.

Use of automatic sand pourers for loose sand models

The consistency of laboratory sand model preparation for physical testing is a fundamental criterion in representing identical geotechnical issues at prototype scale. This objective led to the development of robotic apparatus to eliminate the non-uniformity in manual pouring. Previous studies have shown consistent sand models with high relative density between 50 to 90% produced by the automatic moving-hopper sand pourer at the University of Cambridge, based primarily on a linear correlation to flow rate. However, in the case of loose samples, the influence of other parameters, particularly the drop height, becomes more apparent. In this paper, findings on the effect of flow rate and drop height are discussed in relation to the layer thickness and relative density of loose sand samples. Design charts are presented to illustrate their relationships. The effect of these factors on different sand types is also covered to extend the use of the equipment. © 2010 Taylor & Francis Group, London.

Understandable by design: How can products be designed to align with user experience?

Chapter 14 Understandable by Design: How Can Products be Designed to Align with User Experience? A. Mieczakowski, PM Langdon, RH Bracewell, JJ Patmore and PJ Clarkson 14.1 Introduction Understanding users increases the likelihood that ...

Intelligent products in the supply chain - 10 years on

Ten years ago the intelligent product model was introduced as a means of motivating a supply chain in which product or orders were central as opposed to the organizations that stored or delivered them. This notion of a physical product influencing its own movement through the supply chain was enabled by the evolution of low cost RFID systems which promised low cost connection between physical goods and networked information environments. In 2002 the notion of product intelligence was regarded as a useful but rather esoteric construct. However, in the intervening ten years there have been a number of technological advances coupled with an increasingly challenged business environment which make the prospects for intelligent product deployment seem more likely. This paper reviews a number of these developments and assesses their impact on the intelligent product approach. © 2012 IFAC.

Product life trade-offs: what if products fail early?

Increasing product life allows the embodied emissions in products to be spread across a longer period but can mean that opportunities to improve use-phase efficiency are foregone. In this paper, a model that evaluates this trade-off is presented and used to estimate the optimal product life for a range of metal-intensive products. Two strategies that have potential to save emissions are explored: (1) adding extra embodied emissions to make products more sturdy, increasing product life, and (2) increasing frequency of use, causing early product failure to take advantage of improvements in use-phase efficiency. These strategies are evaluated for two specific case studies (long-life washing machines and more frequent use of vehicles through car clubs) and for a range of embodied and use-phase intensive products under different use-phase improvement rate assumptions. Particular emphasis is placed on the fact that products often fail neither at their design life nor at their optimal life. Policy recommendations are then made regarding the targeting of these strategies according to product characteristics and the timing of typical product failure relative to optimal product life.