Análise química da madeira e casca de diferentes tipos de eucalipto antes e durante o cultivo de shiitake em toras

Avaliaram-se a composição química da madeira e da casca de sete espécies (E. saligna E. grandis, E. urophylla, E. camaldulensis, E. citriodora, E. paniculata e E. pellita) e três clones de eucalipto (híbridos de E. grandis x E. urophylla), antes e durante o cultivo das linhagens LE-95/01 e LE-96/18 de shiitake (Lentinula edodes), em toras. Cada linhagem de shiitake foi inoculada em nove toras de cada tipo de eucalipto com 1 m de comprimento e 9 a 14 cm de diâmetro. Assim, o delineamento experimental foi inteiramente casualizado, com 20 tratamentos e nove repetições, sendo cada repetição correspondente a uma tora. As toras foram mantidas em estufa climatizada, com temperatura de 25 ºC ± 5 e umidade relativa do ar entre 60-80%, durante 12 meses. Para a determinação da composição química da madeira, analisaram-se cunhas de discos e cascas de eucalipto recém-cortadas (sem inoculação das linhagens de L. edodes) e cunhas de discos e cascas retirados de toras já inoculadas com as linhagens de L. edodes após oito meses de incubação. Os resultados mostraram diferenças nos teores de holocelulose, lignina e extrativos totais na madeira e casca após o corte e depois de oito meses de incubação nas espécies e clones de eucalipto; o maior índice de decomposição da holocelulose na madeira, ao longo do tempo, ocorreu no E. saligna (5,5%), indicando, assim, ser o mais favorável para o desenvolvimento micelial do L. edodes. Já na casca aconteceu no clone 24 (22,2%). O E. camaldulensis apresentou o maior índice de decomposição da lignina na madeira (6,8%), ao longo do tempo. Já na casca, entre os eucaliptos testados, o E. grandis sofreu a maior decomposição de lignina (21,9%); o L. edodes degradou muito mais a holocelulose e lignina da casca que da madeira, tornando evidente a importância da casca; a casca da maioria dos tipos de eucaliptos apresentou menor teor de holocelulose, maior teor de extrativos totais e teores de lignina semelhantes ou superiores quando comparados com a madeira. O fator tipo de eucalipto (espécies e clones) teve maior efeito que o fator linhagem de L. edodes na degradação da holocelulose e lignina.

Estudo da influência da temperatura na degradação termoquímica da biomassa de avelós

The bio-oil obtained from the pyrolysis of biomass has appeared as inter-esting alternative to replace fossil fuels. The aim of this work is to evaluate the influence of temperature on the yield of products originating from the pyrolysis process of the powder obtained from the dried twigs of avelós (Euphorbia tirucalli), using a rotating cylinder reactor in laboratory scale. The biomass was treated and characterized by: CHNS, moisture, volatiles, fixed carbon and ashes, as well as evaluation of lignin, cellulose and hemicellulose, besides other instrumental techniques such as: FTIR, TG/DTG, DRX, FRX and MEV. The activation energy was evaluated in non-isothemichal mode with heating rates of 5 and 10 oC/min. The obtained results showed biomass as feedstock with potential for biofuel production, because presents a high organic matter content (78,3%) and fixed-carbon (7,11%). The activation energy required for the degradation of biomass ranged between 232,92 392,84 kJ/mol, in the temperature range studied and heating rate of 5 and 10°C/min. In the pyrolysis process, the influence of the reaction temperature was studied (350-520 ° C), keeping constant the other variables, such as, the flow rate of carrier gas, the centrifugal speed for the bio-oil condensationa, the biomass flow and the rotation of the reactor. The maximum yield of bio-oil was obtained in the temperature of 450°C. In this temperature, the results achieved where: content of bio-oil 8,12%; char 32,7%; non-condensed gas 35,4%; losts 23,8%; gross calorific value 3,43MJ/kg; pH 4,93 and viscosity 1,5cP. The chromatographic analysis of the bio-oil produced under these conditions shows mainly the presence of phenol (17,71%), methylciclopentenone (10,56%) and dimethylciclopentenone (7,76%)

Estudo da influência da temperatura na degradação termoquímica da biomassa de avelós (euphorbia tirucalli Linn)

The bio-oil obtained from the pyrolysis of biomass has appeared as inter-esting alternative to replace fossil fuels. The aim of this work is to evaluate the influence of temperature on the yield of products originating from the pyrolysis process of the powder obtained from the dried twigs of avelós (Euphorbia tirucalli), using a rotating cylinder reactor in laboratory scale. The biomass was treated and characterized by: CHNS, moisture, volatiles, fixed carbon and ashes, as well as evaluation of lignin, cellulose and hemicellulose, besides other instrumental techniques such as: FTIR, TG/DTG, DRX, FRX and MEV. The activation energy was evaluated in non-isothemichal mode with heating rates of 5 and 10 oC/min. The obtained results showed biomass as feedstock with potential for biofuel production, because presents a high organic matter content (78,3%) and fixed-carbon (7,11%). The activation energy required for the degradation of biomass ranged between 232,92 392,84 kJ/mol, in the temperature range studied and heating rate of 5 and 10°C/min. In the pyrolysis process, the influence of the reaction temperature was studied (350-520 ° C), keeping constant the other variables, such as, the flow rate of carrier gas, the centrifugal speed for the bio-oil condensationa, the biomass flow and the rotation of the reactor. The maximum yield of bio-oil was obtained in the temperature of 450°C. In this temperature, the results achieved where: content of bio-oil 8,12%; char 32,7%; non-condensed gas 35,4%; losts 23,8%; gross calorific value 3,43MJ/kg; pH 4,93 and viscosity 1,5cP. The chromatographic analysis of the bio-oil produced under these conditions shows mainly the presence of phenol (17,71%), methylciclopentenone (10,56%) and dimethylciclopentenone (7,76%)

Influência das condições de cultivo na produção de antígenos recombinantes de Leishmania i. chagasi utilizando Escherichia coli M15 cultivada em incubador rotativo e biorreator

Escherichia coli has been one of the most widely used hosts in recombinant protein production, in both laboratory and industrial scale since the advent of recombinant DNA technology. Despite the substantial progress of studies on the molecular biology and immunology of infections, there is currently no medication-based prophylaxis capable of preventing leishmaniasis. As such, there is a great need to identify specific antigens for the development of vaccines and diagnostic kits against visceral leishmaniasis. Thus, the primary goal of the present study is to assess the influence of cultivation conditions on the production of Leishmania chagasi antigens, carried out in a rotating incubator and bioreactor. To that end, several assays were conducted to evaluate the kinetic behavior of antigens (648, 503) of Leishmania. i. chagasi in two different compositions of media (2xTY, TB), with and without an inducer. In order to improve expression, assays were performed in a benchtop bioreactor using the best conditions obtained in a rotating incubator, in addition to assessing the influence of stirring speed. Results show that high complexity of the cultivation medium favored kinetic growth of clones (648, 503). However, in assays submitted to induction by IPTG, this elevated complexity did not promote the expression of recombinant proteins. Expression of antigens 648 and 503 exhibited behavior associated with growth and, in terms of location, proteins 648 and 503 are intracellularly stored. Lactose may be the most adequate inducer in protein expression, when considering factors, cost, toxicity and stability. Elevated stirring may increase cell growth in clone 53, although it may not result in high concentrations for the protein of interest. On the other hand, positive results were obtained for all recombinant clones (648, 503) tested, confirmed by the electrophoretic profile

Bio-óleo e biogás da degradação termoquímica de lodo de esgoto doméstico em cilindro rotativo

The objective of this study was to produce biofuels (bio-oil and gas) from the thermal treatment of sewage sludge in rotating cylinder, aiming industrial applications. The biomass was characterized by immediate and instrumental analysis (elemental analysis, scanning electron microscopy - SEM, X-ray diffraction, infrared spectroscopy and ICP-OES). A kinetic study on non-stationary regime was done to calculate the activation energy by Thermal Gravimetric Analysis evaluating thermochemical and thermocatalytic process of sludge, the latter being in the presence of USY zeolite. As expected, the activation energy evaluated by the mathematical model "Model-free kinetics" applying techniques isoconversionais was lowest for the catalytic tests (57.9 to 108.9 kJ/mol in the range of biomass conversion of 40 to 80%). The pyrolytic plant at a laboratory scale reactor consists of a rotating cylinder whose length is 100 cm with capable of processing up to 1 kg biomass/h. In the process of pyrolysis thermochemical were studied following parameters: temperature of reaction (500 to 600 ° C), flow rate of carrier gas (50 to 200 mL/min), frequency of rotation of centrifugation for condensation of bio-oil (20 to 30 Hz) and flow of biomass (4 and 22 g/min). Products obtained during the process (pyrolytic liquid, coal and gas) were characterized by classical and instrumental analytical techniques. The maximum yield of liquid pyrolytic was approximately 10.5% obtained in the conditions of temperature of 500 °C, centrifugation speed of 20 Hz, an inert gas flow of 200 mL/min and feeding of biomass 22 g/min. The highest yield obtained for the gas phase was 23.3% for the temperature of 600 °C, flow rate of 200 mL/min inert, frequency of rotation of the column of vapor condensation 30 Hz and flow of biomass of 22 g/min. The non-oxygenated aliphatic hydrocarbons were found in greater proportion in the bio-oil (55%) followed by aliphatic oxygenated (27%). The bio-oil had the following characteristics: pH 6.81, density between 1.05 and 1.09 g/mL, viscosity between 2.5 and 3.1 cSt and highest heating value between 16.91 and 17.85 MJ/ kg. The main components in the gas phase were: H2, CO, CO2 and CH4. Hydrogen was the main constituent of the gas mixture, with a yield of about 46.2% for a temperature of 600 ° C. Among the hydrocarbons formed, methane was found in higher yield (16.6%) for the temperature 520 oC. The solid phase obtained showed a high ash content (70%) due to the abundant presence of metals in coal, in particular iron, which was also present in bio-oil with a rate of 0.068% in the test performed at a temperature of 500 oC.

Estudo da produção de biossurfactantes sintetizados por Pseudomonas aeruginosa AP029-GVIIA utilizando manipueira como fonte de carbono

This study evaluates the biosurfactants production from cassava wastewater, an agro industrial residue, to be used as carbon source. Using a factorial design 24-1 (half fraction), 10 tests were performed using Pseudomonas aeruginosa AP029/GVII-A in submerged batch cultivation in rotating incubator (shaker). The influence of factors (temperature, agitation, aeration ratio and concentration of cultivation medium) at two different levels for the synthesis of the biosurfactant. Samples were collected throughout the cultivation by 132 hours of fermentation were completed. The best outcome was intended by following production through substrate consumption, dry matter, reduction of surface tension (ring method) and emulsification index. The kinetics of microorganism was assessed for the carbon source used. The results showed that the cassava wastewater is a well assimilable substrate for the production of biotensoactive, reaching 91 % of consumption by the micro-organism under study. The growth temperature was found to be one of the leading factors in the synthesis of the metabolite, followed by aeration and also due to the agitation. The best results showed a 30 % reduction in surface tension (% RTS) for the environment, reaching values of 30 mN/m; 3.0 g /L of biomass and emulsifying index greater than 65 %. The metabolite synthesized still remained stable for different salt concentrations (1, 5 and 10 % w/ v) and alkaline pH (8-10).

Electrochemical investigation of the dimeric oxo-bridged ruthenium complex in aqueous solution and its incorporation within a cation-exchange polymeric film on the electrode surface for electrocatalytic activity of hydrogen peroxide oxidation

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Uma análise teórica da evolução da rotação estelar

In the past 50 years, large efforts have been made toward the understanding of the stellar evolution. In the observational context, large sets of precise measurements of projected rotational velocity were produced, in particular by the Natal and Geneva groups. From these data, it is now possible to establish the behavior of stellar rotation from the turnoff to the red giant branch. In addition, these data have shown the role of tidal effects on stellar rotation in close binary systems. Nevertheless, relatively little attention has been paid to theoretical studies on the evolution of rotation along the HR Diagram, a topic itself directly associated to the evolution of the stars. Basically, there are two reasons for such a fact, (i) spherical symmetry is not assumed, what leads to a substantial increase in the numerical complexity of equations and (ii) non rotating models have been very successful in explaining relevant observational data, including the mass-luminosity relation and chemical abundances. In spite of these facts, it is clear that considerable work remains to be done on the role of rotation in the later stages of the evolution, where clear disagreements arise from confrontations between theoretical predictions and observations. In the present work we study the evolutionary behavior of stellar rotation along the HR Diagram, taking into account constraint conditions issued from recent observational survey of rotational velocity carried out with high precision procedures and new evolutionary codes

Chemical and microbiological evaluation of the internal surfaces of aluminum tubes both unlined and lined with epoxi resin by means of the stereoscope and scanning electron microscope

A superfície interna das bisnagas fabricadas com alumínio não revestido e revestido com resina epóxi, utilizadas para acondicionar cremes, pomadas, géis, etc., foram avaliadas quimicamente e por métodos microbiológicos correlacionados com a aderência de microrganismos. A prova da porosidade e da resistência à remoção da resina foi observada por meio do microscópio eletrônico de varredura (Topcon FM300) e estereoscópio Leica (MZ12) acoplado a Sistema de Digitalização de Imagens. Para avaliar a ação dos microrganismos foram utilizados corpos-de-prova esterilizados (discos de 10mm de diâmetro), imersos em caldo Mueller Hinton (Difco) e colocados em tubos de polipropileno com tampa de rosca (Corning). Foram inoculados tubos com meio de cultura para cada uma das suspensões bacterianas (10(9)UFC/mL) de Streptococcus agalactiae, Staphylococcus aureus, Acinetobacter lwoffii e Candida albicans, incubados a 37°C, sob agitação constante durante 12 dias. O meio de cultura era trocado a cada 3 dias. Após esse período, os corpos-de prova foram removidos, processados e observados em microscópio eletrônico de varredura JEOL-JSM (T330A). A observação por meio do microscopio eletrônico de varredura mostrou a aderência e a formação de biofilme sobre a superfície de alumínio não revestido e revestido com resina epóxi.

A evolução da rotação estelar na vizinhança solar

Different studies point for an rotation age link following a α tα relationship. The value of the α -parameter has a strong role on the evolutionary behaviour of rotation, because it indicates how strong is the spindown once stars evolve. The well known Skumanich s relation α t −1/2, which is consistent with simple theories of angular momentum loss from rotating stars with magnetic fields and winds, is one of the best accepted. Nevertheless, several studies show clearly that such a relation cannot hold for stars much younger or much older than the Pleiades (100 Mega years) without leading to velocities much greater or much lower than those presently observed. The present study aims at improving this picture on the basis of an enlarged analyses taking into account the role of mass and metallicity on the rotation age relation, based on an unprecedented sample of about 14 000 stars in the solar neighbourhood. From this new approach we show that the α parameter it depends strongly on the stellar age and, by consequence, on the metallicity. In addition, one observes a strong dependence of the referred parameter on the single or binary status of the stars

Experimental study of the conventional equation to determine a plate's moment of inertia

In this work, we describe an experimental setup in which an electric current is used to determine the angular velocity attained by a plate rotating around a shaft in response to a torque applied for a given period. Based on this information, we show how the moment of inertia of a plate can be determined using a procedure that differs considerably from the ones most commonly used, which generally involve time measurements. Some experimental results are also presented which allow one to determine parameters such as the exponents and constant of the conventional equation of a plate's moment of inertia.

2D evaluation of crack openings using smeared and embedded crack models

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência da Dureza dos Discos Abrasivos no Corte de Materiais Dúcteis

O corte de materiais por disco abrasivo é um dos processos que apresentam as melhores características de economia, eficiência e rapidez sendo muito utilizado no meio industrial. Fatores como porcentagens e homogeneidade da mistura dos componentes, tamanho, forma (abrasividade), tenacidade e dureza dos grãos abrasivos, tipos de ligantes e de abrasivos, velocidade de corte e velocidade de mergulho influenciam na segurança, no desempenho e comportamento da operação. Este trabalho apresenta um estudo sobre a influência da dureza dos discos abrasivos no desempenho do processo de corte em operações do tipo remoção a seco. O aumento da dureza dos discos propiciou um aumento da força tangencial de corte e da relação G, devido à mais forte ligação entre o grão e o ligante no compósito. Os resultados mostram que a dureza dos discos abrasivos afeta a economia, pois influencia na vida útil dos discos abrasivos em termos de números de cortes proporcionados; a produtividade, pois está relacionada com o número de trocas de discos desgastados; os esforços necessários para a operação, pois estão relacionados com as forças tangenciais de corte.

Comparação dos valores de desgaste abrasivo e de microdureza de 13 resinas compostas usadas em odontologia através do método do disco retificado

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Qualidade de sono e qualidade de vida em trabalhadores submetidos a diferentes esquemas de trabalho de uma empresa petroquímica

One of the largest problems of the present time resulting from the economic globalization and the modern technology, of the point of view of the biological rhytms of our organism, it is offering services and production of goods available in 24 o'clock, that it demands organized workers in several work schedules besides the hours of the day. Those schedules cause a series of biopsychosocial consequences in the worker's health, in function of circadian, homeostatic and psychosocial alterations. Accordingly, the aim of this study was to accomplish an evaluation of the effects of several works schedules in the pattern of the sleep wake cycle, anxiety, stress and in the health. We counted with a sample of 274 workers subdivided in 49 daytime worker groups and 225 workers in different shift work schedules with different speeds (rotating shift group, slower day shift group, faster day shift group). From the results analysis it is verified irregularities of the daily activities, stress and alterations in the workers' health in all schedules. It was also verified thata the workers thata presented irregularities in the daily activities were the mroe stressed. On the other hand, the shift works were considered more ansious and associated with bad sleep quality. It was verified that the workers with bad sleep quality were those presented larger levels of dispocional anxiety. There was no statistically significant correlation between bad sleep quality and irregular daily lifestyle. However, it can be affirmed thata shift work schendules doesn't are the main determinant for the circadian alterations, but the answers of the individuals to the shifts work; and that the inadequate behavioural strategies to work with the effects of the shift schedules. In conclusion, individual strategies related to the coping of the work in shift (adaptation and tolerance) should be extolled as indispensable tool in the ergonomic evaluation of the work