Morphological traits of surveillant/activated microglia during an experimentally induced acute neuroinflammatory process

Several studies show that morphological changes of microglia over the course of inflammation are tightly coupled to function. However the progressive transformation into activated microglia is poorly characterized. AIMS: This study aimed to establish a spatiotemporal correlation between quantifiable morphological parameters of microglia and the spread of an acute ventricular inflammatory process. METHODS: Inflammation was induced by a single injection of the enzyme neuraminidase within the lateral ventricle of rats. Animals were sacrificed 2, 4 and 12 hours after injection. Coronal slices were immunostained with Iba1 to label microglia and with IL1β to delimit the spread of inflammation. Digital images were obtained by scanning the labelled sections. Single microglia images were randomly selected from periventricular areas of caudate putamen, hippocampus and hypothalamus. FracLac for ImageJ software was used to measure the following morphological parameters: fractal dimension, lacunarity, area, perimeter and density. RESULTS: Significant differences were found in fractal dimension, lacunarity, perimeter and density of microglia cells of neuraminidase injected rats compared to sham animals. However no differences were found in the parameter “area”. In hipoccampus there was a delay in the significant change of the measured parameters. These morphological changes correlated with IL1β-expression in the same areas. CONCLUSIONS: Ventricular inflammation induced by neuraminidase provokes quantifiable morphological changes in microglia restricted to areas labelled with IL1β. Morphological parameters of microglia such as fractal dimension, lacunarity, perimeter and density are sensitive and valuable tools to quantify activation. However, the extensively used parameter “area” did not change upon microglia activation.

Non chemical natural organic matter removal with a contact TiO2 process

Dissertação de Mestrado, Tecnologia dos Alimentos, Instituto Superior de Engenharia, Universidade do Algarve, 2014

Fitting phase type distribution to service process with sequential phases

The work of this thesis is concerned with fitting Hypo-exponential and Erlang phase type distributions for modeling real life processes with non-exponential service time. There exist situations where exponential distributions cannot explain the distribution of service time properly. This thesis presents the application of two traditional statistical estimation techniques to approximate the service distributions of processes with coefficient of variation less than one. It also presents an algorithm to fit Hypo-exponential distribution for complex situations which can’t be handled properly with traditional estimation techniques. The result shows the effect of variation of sample size and other parameters on the efficiency of the estimation techniques by comparing their respective outputs. Furthermore it checks how accurately the proposed algorithm approximates a given distribution.

Multi-objective optimization of material model parameters of an adhesive layer by using SPEA2

The usage of multi material structures in industry, especially in the automotive industry are increasing. To overcome the difficulties in joining these structures, adhesives have several benefits over traditional joining methods. Therefore, accurate simulations of the entire process of fracture including the adhesive layer is crucial. In this paper, material parameters of a previously developed meso mechanical finite element (FE) model of a thin adhesive layer are optimized using the Strength Pareto Evolutionary Algorithm (SPEA2). Objective functions are defined as the error between experimental data and simulation data. The experimental data is provided by previously performed experiments where an adhesive layer was loaded in monotonically increasing peel and shear. Two objective functions are dependent on 9 model parameters (decision variables) in total and are evaluated by running two FEsimulations, one is loading the adhesive layer in peel and the other in shear. The original study converted the two objective functions into one function that resulted in one optimal solution. In this study, however, a Pareto frontis obtained by employing the SPEA2 algorithm. Thus, more insight into the material model, objective functions, optimal solutions and decision space is acquired using the Pareto front. We compare the results and show good agreement with the experimental data.

Dynamical modeling of biogas production supported by an experimental anaerobic digestion process

This paper presents the development of a combined experimental and numerical approach to study the anaerobic digestion of both the wastes produced in a biorefinery using yeast for biodiesel production and the wastes generated in the preceding microbial biomass production. The experimental results show that it is possible to valorise through anaerobic digestion all the tested residues. In the implementation of the numerical model for anaerobic digestion, a procedure for the identification of its parameters needs to be developed. A hybrid search Genetic Algorithm was used, followed by a direct search method. In order to test the procedure for estimation of parameters, first noise-free data was considered and a critical analysis of the results obtain so far was undertaken. As a demonstration of its application, the procedure was applied to experimental data.

Different Parameters Variation Analysis of a PV Cell

The paper states an introduction, description and implementation of a PV cell under the variation of parameters. Analysis and observation of a different parameters variation of a PV cell are discussed here. To obtain the model for the purpose of analyzing an equivalent circuit with the consisting parameters a photo current source, a series resistor, a shunt resistor and a diode is used. The fundamental equation of PV cell is used to study the model and to analyze and best fit observation data. The model can be used in measuring and understanding the behaviour of photovoltaic cells for certain changes in PV cell parameters. A numerical method is used to analyze the parameters sensitivity of the model to achieve the expected result and to understand the deviation of changes in different parameters situation at various conditions respectively. The ideal parameters are used to study the models behaviour. It is also compared the behaviour of current-voltage and power-voltage by comparing with produced maximum power point though it is a challenge to optimize the output with real time simulation. The whole working process is also discussed and an experimental work is also done to get the closure and insight about the produced model and to decide upon the validity of the discussed model.