Desenvolvimento e otimização de materiais nanocristalinos para células solares sensibilizadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização de filmes finos polimerizados por plasma a partir dos monômeros hexametildisilazano e acetileno e posteriormente expostos à descarga por barreira dielétrica

Pós-graduação em Engenharia Mecânica - FEG

Influence of the network modifier on the characteristics of MSnO3 (M=Sr and,Ca) thin films synthesized by chemical solution deposition

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Nanometer Scale Titanium Surface Texturing Are Detected by Signaling Pathways Involving Transient FAK and Src Activations

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Polymer Matrix-Based Piezoelectric Composite for Structural Health Monitoring

Structural health monitoring (SHM) refers to the procedure of assessing the structure conditions continuously so it is an alternative to conventional nondestructive evaluation (NDE) techniques [1]. With the growing developments in sensor technology acoustic emission (AE) technology has been attracting attention in SHM applications. AE are characterized by waves produced by the sudden internal stress redistribution caused by the changes in the internal structure, such as fatigue, crack growth, corrosion, etc. Piezoelectric materials such as Lead Zirconate Titanate (PZT) ceramic have been widely used as sensor due to its high electromechanical coupling factor and piezoelectric d coefficients. Because of the poor mechanical characteristic and the lack in the formability of the ceramic, polymer matrix-based piezoelectric composites have been studied in the last decade in order to obtain better properties in comparison with a single phase material. In this study a composite film made of polyurethane (PU) and PZT ceramic particles partially recovered with polyaniline (PAni) was characterized and used as sensor for AE detection. Preliminary results indicate that the presence of a semiconductor polymer (PAni) recovering the ceramic particles, make the poling process easier and less time consuming. Also, it is possible to observe that there is a great potential to use such type of composite as sensor for structure health monitoring.

Measurement of Radiant Energy using Pyroelectric Polymer/Ceramic Composite

Monitoring non-ionizing radiant energy is increasingly demanded for many applications such as automobile, biomedical and security system. Thermal type infrared (IR) sensors can operate at room temperature and pyroelectric materials have high sensitivity and accuracy for that application. Working as thermal transducer pyroelectric sensor converts the non-quantified thermal flux into the output measurable quantity of electrical charge, voltage or current. In the present study the composite made of poly(vinylidene fluoride) -PVDF and lead zirconate titanate (PZT) partially recovered with polyaniline (PAni) conductor polymer has been used as sensor element. The pyroelectric coefficient p(T) was obtained by measuring the pyroelectric reversible current, i.e., measuring the thermally stimulated depolarization current (TSDC) after removing all irreversible contribution to the current such as injected charge during polarization of the sample. To analyze the sensing property of the pyroelectric material, the sensor is irradiated by a high power light source (halogen lamp of 250 W) that is chopped providing a modulated radiation. A device assembled in the laboratory is used to change the light intensity sensor, an aluminum strip having openings with diameters ranging from 1 to 10 mm incremented by one millimeter. The sensor element is assembled between two electrodes while its frontal surface is painted black ink to maximize the light absorption. The signal from the sensor is measured by a Lock-In amplifier model SR530 -Stanford Research Systems. The behavior of the output voltage for an input power at several frequencies for PZT-PAni/PVDF (30/ 70 vol%) composite follows the inverse power law (1/ f) and the linearity can be observed in the frequency range used.

Effects of Dextrose and Lipopolysaccharide on the Corrosion Behavior of a Ti-6Al-4V Alloy with a Smooth Surface or Treated with Double-Acid-Etching

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fabrication and Characterization of PZT-PAni/PVDF Based Nanocomposite

This work presents the preparation and characterization of PZT ceramic obtained by the polymeric precursor method (PPM). The influence of the synthesis method on the grain size and the morphology are also object of study. The fabrication and characterization of composite films with 0-3 connectivity, immersing nanoparticles of PZT into the non-polar poly(vinylidene fluoride) -PVDF as the polymer matrix were presented. For comparison there are results obtained with composite samples made of ceramic particles unrecovered and recovered with a conducting polymer, the polyaniline (PAni).

Characterization of natural rubber membranes using scaling laws analysis

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Melanin as an active layer in biosensors

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Nanostructured screen-printed electrodes modified with self-assembled monolayers for determination of metronidazole in different matrices

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise da superfície de cerâmicas de dissilicato de lítio após imersão em soluções ácidas e a base de flúor

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Thermo-sensitive chitosan-cellulose derivative hydrogels: swelling behaviour and morphologic studies

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Surface modification of polymeric materials by cold atmospheric plasma jet

In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40 degrees in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure. (C) 2014 Elsevier B.V. All rights reserved.

Sn(1-x)LaxO2 thin films deposited on AISI 304 stainless steel substrates

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)