Undersampled Critical Branching Processes on Small-World and Random Networks Fail to Reproduce the Statistics of Spike Avalanches

The power-law size distributions obtained experimentally for neuronal avalanches are an important evidence of criticality in the brain. This evidence is supported by the fact that a critical branching process exhibits the same exponent t~3=2. Models at criticality have been employed to mimic avalanche propagation and explain the statistics observed experimentally. However, a crucial aspect of neuronal recordings has been almost completely neglected in the models: undersampling. While in a typical multielectrode array hundreds of neurons are recorded, in the same area of neuronal tissue tens of thousands of neurons can be found. Here we investigate the consequences of undersampling in models with three different topologies (two-dimensional, small-world and random network) and three different dynamical regimes (subcritical, critical and supercritical). We found that undersampling modifies avalanche size distributions, extinguishing the power laws observed in critical systems. Distributions from subcritical systems are also modified, but the shape of the undersampled distributions is more similar to that of a fully sampled system. Undersampled supercritical systems can recover the general characteristics of the fully sampled version, provided that enough neurons are measured. Undersampling in two-dimensional and small-world networks leads to similar effects, while the random network is insensitive to sampling density due to the lack of a well-defined neighborhood. We conjecture that neuronal avalanches recorded from local field potentials avoid undersampling effects due to the nature of this signal, but the same does not hold for spike avalanches. We conclude that undersampled branching-process-like models in these topologies fail to reproduce the statistics of spike avalanches.

Ecologia alimentar e reprodutiva da piaba-do-rabo-amarelo, Astyanax cf. lacustris (Reinhardt, 1874) (Osteichthyes: Characidae) na Lagoa do Piató, Assu, Rio Grande do Norte, Brasil

The feeding habits and biological aspects of the reproductive cycle of two-spot astyanax, Astyanax cf. lacustris (Reinhardt, 1874) were investigated. Fish samples were captured on a monthly basis, using gillnets of 4 cm mesh size, from the Piató Lake, Assu, Rio Grande do Norte, during the period of September, 2006 to August, 2007. Physico-chemical parameters, such as, temperature, electrical conductivity and dissolved oxygen of the lake were registered. The monthly values of rainfall also were obtained. The 360 individuals captured, were measured, weighed, dissected, and stomach weight and the stage of gonadal maturity were registered. The stomach contents analyses were carried out based on volumetric method, points, frequency of occurrence and applying the Index of Relative Importance. The degrees of repletion of the stomachs were determined besides the Index of Repletion relating to feeding activity variations and frequency of ingestion with limnological parameters and rainfall. The food items identified were separated into distinct groups according to their origin. Sex ratio and Gonadosomatic Relation of females were verified to determine the spawning period and fecundity. The physico-chemical parameters presented the following annual mean values: temperature = 28.8ºC, electrical conductivity = 992.5 µS.cm-1; dissolved oxygen = 4.9 mg.L-1 during the study period. The annual mean of the rainfall was 63.5 mm. The results indicate that this species present an omnivorous feeding habit with a tendency towards insectivory, with an increase in feeding activity during the dry season. The aquatic oxygen to interfere very importance in the feeding activity than the others factors physico-chemicals of water and rainfall. There was a predominance of females, with a sex proportion of 1M:7F. The macroscopic characteristics of the ovaries and testicles revealed four stages of gonadal development: immature, maturing, mature and spent. A temporal variation was observed for the gonadal development of males and females. There was reproductive activity through out the year, with peaks in the months of February, April and June to correspond with the rain of precipitation of the region. The mean fecundity was 7.681 mature oocytes, varying from 4.476 to 12.036, with mean of 7.681. There was positive relation between fecundity and body mass. Condition Factor is not an efficient indicator of the reproductive period of this species. The species A. cf. lacustris is an opportunist and is well adapted to the conditions of the semi-arid Caatinga Biome

Diagnóstico ecotoxicológico dos efluentes lançados no complexo estuarino do Jundiaí/Potengi, Natal/RN

Untreated effluents that reach surface water affect the aquatic life and humans. This study aimed to evaluate the wastewater s toxicity (municipal, industrial and shrimp pond effluents) released in the Estuarine Complex of Jundiaí- Potengi, Natal/RN, through chronic quantitative e qualitative toxicity tests using the test organism Mysidopsis Juniae, CRUSTACEA, MYSIDACEA (Silva, 1979). For this, a new methodology for viewing chronic effects on organisms of M. juniae was used (only renewal), based on another existing methodology to another testorganism very similar to M. Juniae, the M. Bahia (daily renewal).Toxicity tests 7 days duration were used for detecting effects on the survival and fecundity in M. juniae. Lethal Concentration 50% (LC50%) was determined by the Trimmed Spearman-Karber; Inhibition Concentration 50% (IC50%) in fecundity was determined by Linear Interpolation. ANOVA (One Way) tests (p = 0.05) were used to determinate the No Observed Effect Concentration (NOEC) and Low Observed Effect Concentration (LOEC). Effluents flows were measured and the toxic load of the effluents was estimated. Multivariate analysis - Principal Component Analysis (PCA) and Correspondence Analysis (CA) - identified the physic-chemical parameters better explain the patterns of toxicity found in survival and fecundity of M. juniae. We verified the feasibility of applying the only renewal system in chronic tests with M. Juniae. Most efluentes proved toxic on the survival and fecundity of M. Juniae, except for some shrimp pond effluents. The most toxic effluent was ETE Lagoa Aerada (LC50, 6.24%; IC50, 4.82%), ETE Quintas (LC50, 5.85%), Giselda Trigueiro Hospital (LC50, 2.05%), CLAN (LC50, 2.14%) and COTEMINAS (LC50, IC50 and 38.51%, 6.94%). The greatest toxic load was originated from ETE inefficient high flow effluents, textile effluents and CLAN. The organic load was related to the toxic effects of wastewater and hospital effluents in survival of M. Juniae, as well as heavy metals, total residual chlorine and phenols. In industrial effluents was found relationship between toxicity and organic load, phenols, oils and greases and benzene. The effects on fertility were related, in turn, with chlorine and heavy metals. Toxicity tests using other organisms of different trophic levels, as well as analysis of sediment toxicity are recommended to confirm the patterns found with M. Juniae. However, the results indicate the necessity for implementation and improvement of sewage treatment systems affluent to the Potengi s estuary

Abundância e distribuição sazonal de espécies autóctones de camarões peneídeos no canal de abastecimento do sistema primar de aquicultura orgânica (Laguna de Guaraíras, Tibau do Sul, Rio Grande do Norte, Brasil)

Guaraíras lagoon, located in Tibau do Sul in the eastern littoral of Rio Grande do Norte (Brazil), presents a permanent connection to the sea, which guarantees the occurrence of a rich biodiversity, which includes the autochthonous shrimp species Litopenaeus schmitti, Farfantepenaeus subtilis and Farfantepenaeus brasiliensis. In spite of being subject to a strong human intervention in the last decade, mainly related to the installation of shrimp (Litopenaeus vannamei) farms, the lagoon is still scarcely studied. The present study aims at characterizing the populations of the three autochthonous penaeid shrimp species inhabiting Guaraíras, taking into consideration their abundance and seasonal distribution in the inflow channel of Primar System of Organic Aquaculture (Tibau do Sul, Rio Grande do Norte, Brazil). Twelve monthly samples were carried out from May 2005 to April 2006 with the aid of a circular cast net in the inflow channel, which is daily supplied with water from Guaraíras. Sampling months were grouped in trimesters according to the total pluviosity, thus comprising four trimesters. Water salinity was monitored twice a week and temperature values registered on a daily basis at noon, during the study period. The daily pluviosity data from the municipality of Tibau do Sul were supplied by Empresa de Pesquisa Agropecuária do Rio Grande do Norte (EMPARN). Collected shrimp were identified, weighted, measured and sexed. L. schmitti specimens (0.2 g to 17.8 g) were distributed in 1.3 g weight classes intervals. From the eighth sampling month (December 2005) onwards, males were classified into three categories, in accordance with the development of their petasm: (a) rudimentary petasm, (b) partially formed petasm, and (c) completely formed petasm. Among the ecological variables, rainfall showed the greatest dispersion (s.d.=187.74Rainfall and abundance of L. schmitti were negatively correlated (r = -0.85) whereas its abundance and water salinity were positively correlated (r = 0.63). Among 1,144 collected individuals, 1,127 were L. schmitti, 13 were F. subtilis and 4 were F. brasiliensis, which corresponded to 98.51%, 1.14% and 0.35% of the total of collected individuals. L. schmitti occurred in 100 % of all samples. Differently, the presence of F. subtilis and F. brasiliensis was restricted to 33% and 17% of the collected samples, respectively. The present study confirmed the occurrence of L. schmitti, F. brasiliensis and F. subtilis in Guaraíras. However, this lagoon seems to be primarily inhabited by juvenile Litopenaeus schmitti. The population of L. schmitti analysed showed a seasonal pattern of distribution. In general, in the months of high salinity and absence of rain, the number of individuals was higher than in the wet months. Further studies on the reproductive biology and ecology of L. schmitti, F. brasiliensis and F. subtilis may elucidate questions referring to the abundance, period, and phase of occurrence of these shrimp genera in Guaraíras. Finally, the risks associated to the establishment of L. vannamei in the lagoon provide a novel outlet for studies in this biotope

Utilização da macroalga Ulva lactuca linnaeus na redução de nutrientes (NH4+,NO3- e PO4-2) provenientes da carcinicultura

Dentre as macroalgas capazes de absorver altas concentrações de N e P dissolvidos na água, destaca-se a Chlorophyta Ulva lactuca, bastante adaptável e resistente às adversidades ambientais, como grandes variações de temperatura, salinidade, matéria orgânica e metais pesados. Trata-se também de uma espécie bastante comum nas áreas intertidais do litoral norte-riograndense. Devido a suas características ecológicas, fisiológicas e nutricionais, foi avaliado nesse estudo, o seu potencial como biofiltro na redução de NH4+, NO3- e PO4-2, tanto em condições controladas como também em um viveiro de camarão. No experimento laboratorial, foram utilizados quatro aquários de vidro de 30 x 20 x 20cm com 10L de água, sendo três aquários experimentais contendo 20g de U. lactuca e um controle. O acréscimo de biomassa foi de 2,92g (22,92 ± 6,29g; p < 0,05) em relação ao inóculo inicial de 20g, sob temperatura (28,50 ± 0,58ºC), salinidade (35,00 ± 0,00 ), pH (8,26 ± 0,02) e luz constante (250 μmol.m2s-1). O crescimento positivo (1,78 ± 4,38%dia-1; p < 0,05), juntamente com a alta eficiência de absorção de amônio (83%; p < 0,001), nitrato (83%; p < 0,001) e ortofosfato (53%; p < 0,001), demonstrou que, nessas condições, a Ulva lactuca absorveu os nutrientes e aumentou sua biomassa. Já no experimento de campo, realizado na fazenda TECNARÃO, situada no município de Arez/RN (06° 11 40 Latitude Sul, e 35º 09 37 Longitude Oeste), foram utilizadas três gaiolas de PVC, posicionadas a 12cm da superfície da água, cada uma com dimensões de aproximadamente 59 x 59 x 15cm, onde foram colocadas 200g de U. lactuca. O ganho de biomassa de 3g (203,00 ± 41,02g; p < 0,001) foi muito semelhante às condições controladas, demonstrando a adaptabilidade da espécie em condições ambientais variáveis, onde, apesar da temperatura pouco variável (27,45 ± 0,64ºC), houve progressiva diminuição de salinidade (25 - 15 ), devido ao período de fortes chuvas (34,70 ± 23,78mm). Somado a isso, foram observados vários fatores biológicos interferindo no viveiro, como a presença de epífitas, organismos endofíticos, fouling e a herbivoria por parte dos próprios camarões. Houve aumento nas concentrações de NH4+ (4,36 ± 1,69 μmol.L-1), NO3- (0,17 ± 0,25μmol.L-1) e PO4-2 (0,41 ± 0,13μmol.L-1), coincidindo com o crescimento da espécie até a terceira semana. Todos os parâmetros ambientais analisados, assim como a biomassa e a Taxa de Crescimento Relativo (TCR), obtidos no campo, apresentaram variações altamente significativas (p < 0,001). As correlações observadas entre biomasa e NH4+ (r = 0,82; p < 0,001) e entre biomassa e PO4-2 (r = 0,87; p < 0,001), indicam que esta espécie é capaz de ter um crescimento satisfatório nas condições eutróficas de um viveiro de camarão, sendo possível seu uso como biofiltro.

Influência do lodo de ETE na massa para fabricação de cerâmica vermelha

The WTP produce many kinds of residue on your treatment stages, but the sludge is the more problematic from the final disposition point view. The actual rate of residue production deriving from technological evolution and the crescent population needs prevents the subtle equilibrium generation between consumption and recycling/reuse, creating problems of pollution resulting from inappropriate management of residues. Thus, is necessary achieve a new equilibrium between the grow from raw materials and energy and the residue generation. This equilibrium should be achieved by technical and economic feasibility of environmental supported models through recycling and reuse. The red ceramic industry stand out in residue absorption question as raw material due their clay mass heterogeneity, constituted by clay minerals and non-clay minerals with wide mineralogical variation, allowing residue inclusion which act like plastic or non-plastic materials, contributing to retain heavy metals contained in residues in the vitreous mass formed during the burning of the ceramic bodies. This work propose the study of the influence of incorporation of 25 wt.% sludge from wastewater treatment plant, according preliminary results, in the mass to produce ceramic bodies. The raw materials was characterized through chemical composition analyses by XRF, mineralogical analyses by XRD, thermal analyses by TG and DTA, Atterberg limits and thermodilatometry. Subsequently was composed the mass with 75 wt.% of clay and 25 wt.% of dried wastewater sludge from UFRN WWTP. Samples with 6,0 x 2,0 x 0,5 cm was produced with unidirectional compacting under pressure of 20MPa and burned in temperatures between 950 and 1,200ºC. After fired, the ceramic bodies have been submitted to physical and mechanical analyses through the measure of firing shrinkage, water absorption, density, apparent porosity and flexural strength; crystallographic analyses through XRD and microstructure analyses by SEM. The technological properties obtained was satisfactory to production of roof tiles with 25 wt.% at 1,200 ºC, but the production of others products at lower temperatures was not feasible

Estudos de Durabilidade Frente ao Ataque Ácido de Compósitos Portland-Polímero para Cimentação de Poços de Petróleo

Portland-polymers composites are promising candidates to be used as cementing material in Northeastern oil wells of Brazil containing heavy oils submitted to steam injection. In this way, it is necessary to evaluate its degradation in the commonly acidizind agents. In addition, to identify how aggressive are the different hostile environments it is an important contribution on the decision of the acidic systems to be used in. It was investigated the performance of the Portland-polymer composites using powdered polyurethane, aqueous polyurethane, rubber tire residues and a biopolymer, those were reinforced with polished carbon steel SAE 1045 to make the electrochemical measurements. HCl 15,0 %, HCl 6,0 % + HF 1,5 % (soft mud acid), HCl 12,0 % + HF 3,0 % (regular mud acid) and HAc 10 % + HF 1,5 % were used as degrading environment and electrolytes. The more aggressive acid solution to the plain Portland hardened cement paste was the regular mud acid, that showed loss of weight around 23.0 %, followed by the soft mud acid, the showed 11.0 %, 15.0 % HCl with 7,0 % and, at last the 10.0 % HAc plus HF 1.5 % with just 1.0 %. The powdered polyurethane-composite and the aqueous polyurethane one showed larger durability, with reduction around 87.0 % on the loss of weight in regular mud acid. The acid attack is superficial and it occurs as an action layer, where the degraded layer is responsible for the decrease on the kinetic of the degrading process. This behavior can be seen mainly on the Portland- aqueous polyurethane composite, because the degraded layer is impregnated with chemically modified polymer. The fact of the acid attack does not have influence on the compressive strength or fratography of the samples, in a general way, confirms that theory. The mechanism of the efficiency of the Portland-polymers composites subjected to acid attack is due to decreased porosity and permeability related with the plain Portland paste, minor quantity of Ca+2, element preferentially leached to the acidic solution, wave effect and to substitute part of the degrading bulk for the polymeric one. The electrolyte HAc 10 % + HF 1,5 % was the least aggressive one to the external corrosion of the casing, showing open circuit potentials around +250 mV compared to -130 mV to the simulated pore solution to the first 24 hours immersion. This behavior has been performed for two months at least. Similar corrosion rates were showed between both of the electrolytes, around 0.01 μA.cm-2. Total impedance values, insipient arcs and big polarization resistance capacitive arcs on the Nyquist plots, indicating passivity process, confirm its efficiency. In this way, Portlandpolymers composites are possible solutions to be succeed applied to oilwell cementing concomitant submitted to steam injection and acidizing operation and the HAc 10,0 % + HF 1,5 % is the less aggressive solution to the external corrosion of the casing

Adsorção de Pb(II) utilizando adsorvente composto por montmorilonita e dolomita

The destructive impact of improper disposal of heavy metals in the environment increases as a direct result of population explosion, urbanization and industrial expansion and technological developments. Argil are potential materials for adsorption of inorganic and the pelletization of it is required for use in adsorptive columns of fixed bed. The low cost and the possibility of regeneration makes these materials attractive for use in the purification process, capable of removing inorganic compounds in contaminated aquatic environments. In this work was made pellets of a mixture of dolomite and montmorillonite by wet agglomeration, in different percentages. The removal of Pb (II) was investigated through experimental studies, and was modeled by kinetic models and isotherms of adsorption. The materials were characterized using the techniques of XRD, TG / DTA, FT-IR, and surface area by BET method. The results showed the adsorption efficiency of the contaminant by the composite material studied in synthetic solution. The study found that the adsorption follows the Langmuir model, and the kinetics of adsorption follows the model of pseudosecond order

Obtenção de filtro cerâmico a partir da diatomita e casca de arroz carbonizada visando tratamento de efluente têxtil

The effluents released by the textile industry have high concentrations of alkali, carbohydrates, proteins, in addition to colors containing heavy metals. Therefore, a filter was prepared aiming primarily to the removal of color. In order to prepare this filter, rice hulls and diatomite were used, which have in their structure, basically amorphous hydrated silica. The silica exists in three crystalline forms: quartz, tridymite and cristobalite. In accordance with the above considerations, this study was divided into two stages; the first corresponds to the preparation of the filter and the second to carry out the tests in the effluent/filter in order to verify the efficiency of the color removal. First, the raw material was subjected to a chemical analysis and XRD, and then the diatomite was mixed, via humid, with a planetarium windmill with 20 %, 40 %, 60 % and 80 % of rice husk ash. To the mixture, 5 % carboxymethylcellulose (CMC) was added as a binder at room temperature. The samples were uniaxially compacted into metallic matrix of 0.3 x 0.1 cm² of area at a pressure of 167 MPa by means of hydraulic press and then sintered at temperatures of 1,000 °C, 1,200 °C and 1,400 °C for 1 h and submitted to granulometry test using laser, linear retraction, water absorption, apparent porosity and resistance to bending, DTA, TMA and XRD. To examine the pore structure of the samples scanning electron microscope (SEM) was used. Also tests were carried out in a mercury porosimeter to verify the average size of the pores and real density of the samples. In the second stage, samples of the effluent were collected from a local industry, whose name will be preserved, located in Igapó, in the State of Rio Grande do Norte - RN. The effluent was first pretreated before filtration and then subjected to a treatment of flotation. The effluent was then characterized before and after filtration, with parameters of color, turbidity, suspended solids, pH, chemical and biochemical oxygen demand (COD and BOD). Thus, through the XRD analysis the formation of cristobalite α in all samples was observed. The best average size of pore was found to be 1.75 μm with 61.04 % apparent porosity, thus obtaining an average 97.9 % color removal and 99.8 % removal of suspended solid

Formulação de pastas cimentícias com adição de suspensões de quitosana para cimentação de poços de petróleo

Primary cementing is one of the main operations in well drilling responsible for the mechanical stability and zonal isolation during the production of oil. However, the cement sheath is constantly under mechanical stresses and temperature variations caused by the recovery of heavy oil. In order to minimize fracture and wear of the cement sheath, new admixtures are developed to improve the properties of Portland cement slurries and avoid environmental contamination caused by leaking gas and oil. Polymers with the ability to form polymeric films are candidates to improve the properties of hardened cement slurries, especially their fracture energy. The present study aimed at evaluating the effect of the addition of a chitosan suspension on cement slurries in order to improve the properties of the cement and increase its performance on heavy oil recovery. Chitosan was dissolved in acetic ac id (0.25 M and 2 M) and added to the formulation of the slurries in different concentrations. SEM analyses confirmed the formation of polymeric films in the cementitious matrix. Strength tests showed higher fracture energy compared to slurries without the addition of chitosan. The formation of the polymeric films also reduced the permeability of the slurry. Therefore, chitosan suspensions can be potentially used as cementing admixtures for heavy oil well applications

Estudo paramétrico da segregação gravitacional na injeção contínua de vapor

Steam injection is the most used method of additional recovery for the extraction of heavy oil. In this type procedure is common to happen gravitational segregation and this phenomenon can affect the production of oil and therefore, it shoulds be considered in the projects of continuous steam injection. For many years, the gravitational segregation was not adequately considered in the calculation procedures in Reservoir Engineering. The effect of the gravity causes the segregation of fluids inside the porous media according to their densities. The results of simulation arising from reservoirs could provide the ability to deal with the gravity, and it became apparent that the effects of the gravity could significantly affect the performance of the reservoir. It know that the gravitational segregation can happen in almost every case where there is injection of light fluid, specially the steam, and occurs with greater intensity for viscous oil reservoirs. This work discusses the influence of some parameters of the rock-reservoir in segregation as viscosity, permeability, thickness, cover gas, porosity. From a model that shows the phenomenon with greater intensity, optimized some operational parameters as the rate flow rate steam, distance between the wells injector-producer, and interval of completion which contributed to the reduction in gravity override, thus increasing the oil recovery. It was shown a greater technical-economic viability for the model of distance between the wells 100 m. The analysis was performed using the simulator of CMG (Computer Modeling Group-Stars 2007.11, in which was observed by iterating between studied variables in heavy oil reservoirs with similar characteristics to Brazilian Northeast

Estudo paramétrico da injeção de vapor em reservatórios delgados

Exploration of heavy oil reservoirs is increasing every year in worldwide, because the discovery of light oil reservoirs is becoming increasingly rare. This fact has stimulated the research with the purpose of becoming viable, technically and economically, the exploration of such oil reserves. In Brazil, in special in the Northeast region, there is a large amount of heavy oil reservoir, where the recovery by the so called secondary methods Water injection or gas injection is inefficient or even impracticable in some reservoirs with high viscosity oils (heavy oils). In this scenario, steam injection appears as an interesting alternative for recover of these kinds of oil reservoirs. Its main mechanism consists of oil viscosity reduction through steam injection, increasing reservoir temperature. This work presents a parametric simulation study of some operational and reservoir variables that had influence on oil recovery in thin reservoirs typically found in Brazilian Northeast Basins, that use the steam injection as improved oil recovery method. To carry out simulations, it was used the commercial software STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modeling Group) version 2007.11. Reservoirs variables studied were horizontal permeability, vertical and horizontal permeability ratio, water zone and pay zone thickness ratio, pay zone thickness and thermal conductivity of the rock. Whereas, operational parameters studied were distance between wells and steam injection rate. Results showed that reservoir variables that had more influence on oil recovery were horizontal permeability and water zone and pay zone thickness ratio. In relation to operational variables, results showed that short distances between wells and low steam injection rates improved oil recovery

Estudo da segregação gravitacional do processo de injeção de vapor em reservátórios heterogêneos

Due to reservoirs complexity and significantly large reserves, heavy oil recovery has become one of the major oil industry challenges. Thus, thermal methods have been widely used as a strategic method to improve heavy oil recovery. These methods improve oil displacement through viscosity reduction, enabling oil production in fields which are not considered commercial by conventional recovery methods. Among the thermal processes, steam flooding is the most used today. One consequence in this process is gravity segregation, given by difference between reservoir and injected fluids density. This phenomenon may be influenced by the presence of reservoir heterogeneities. Since most of the studies are carried out in homogeneous reservoirs, more detailed studies of heterogeneities effects in the reservoirs during steam flooding are necessary, since most oil reservoirs are heterogeneous. This paper presents a study of reservoir heterogeneities and their influence in gravity segregation during steam flooding process. In this study some heterogeneous reservoirs with physical characteristics similar those found in the Brazilian Northeast Basin were analyzed. To carry out the simulations, it was used the commercial simulator STARS by CMG (Computer Modeling Group) - version 2007.11. Heterogeneities were modeled with lower permeability layers. Results showed that the presence of low permeability barriers can improve the oil recovery, and reduce the effects of gravity segregation, depending on the location of heterogeneities. The presence of these barriers have also increased the recovered fraction even with the reduction of injected steam rate

Estudo paramétrico da recuperação de petróleo pesado por aquecimento eletromagnético resistivo

Electrical resistive heating (ERH) is a thermal method used to improve oil recovery. It can increase oil rate and oil recovery due to temperature increase caused by electrical current passage through oil zone. ERH has some advantage compared with well-known thermal methods such as continuous steam flood, presenting low-water production. This method can be applied to reservoirs with different characteristics and initial reservoir conditions. Commercial software was used to test several cases using a semi-synthetic homogeneous reservoir with some characteristics as found in northeast Brazilian basins. It was realized a sensitivity analysis of some reservoir parameters, such as: oil zone, aquifer presence, gas cap presence and oil saturation on oil recovery and energy consumption. Then it was tested several cases studying the electrical variables considered more important in the process, such as: voltage, electrical configurations and electrodes positions. Energy optimization by electrodes voltage levels changes and electrical settings modify the intensity and the electrical current distribution in oil zone and, consequently, their influences in reservoir temperature reached at some regions. Results show which reservoir parameters were significant in order to improve oil recovery and energy requirement in for each reservoir. Most significant parameters on oil recovery and electrical energy delivered were oil thickness, presence of aquifer, presence of gas cap, voltage, electrical configuration and electrodes positions. Factors such as: connate water, water salinity and relative permeability to water at irreducible oil saturation had low influence on oil recovery but had some influence in energy requirements. It was possible to optimize energy consumption and oil recovery by electrical variables. Energy requirements can decrease by changing electrodes voltages during the process. This application can be extended to heavy oil reservoirs of high depth, such as offshore fields, where nowadays it is not applicable any conventional thermal process such as steam flooding

Influência da areia argilosa na recuperação de petróleo por injeção de vapor

Continuous steam injection is one of heavy oil thermal recovery methods used in the Brazilian Northeast because of high occurrence of heavy oil reservoir. In this process, the oil into the reservoir is heated while reduces, substantially, its viscosity and improves the production. This work analyzed how the shaly sand layers influenced in the recovery. The studied models were synthetics, but the used reservoir data can be extrapolated to real situations of Potiguar Basin. The modeling was executed using the STARS - Steam Thermal and Advanced Process Reservoir Simulator - whose version was 2007.10. STARS is a tool of CMG Computer Modeling Group. The study was conducted in two stages, the first we analyzed the influence of reservoir parameters in the thermal process, so some of these were studied, including: horizontal permeability of the reservoir and the layer of shaly sand, ratio of horizontal permeability to vertical permeability, the influence of capillary pressure layer of shaly sand and as the location and dimensions of this heterogeneity can affect the productivity of oil. Among the parameters studied the horizontal permeability of the reservoir showed the most significant influence on the process followed by diversity. In the second stage three models were selected and studied some operational parameters such as injection rate, distance between wells, production time and completion intervals. Among the operating parameters studied the low rate and intermediate distances between wells showed the best recoveries