Development of LRFD Procedures for Bridge Pile Foundations in Iowa: Volume II: Field Testing of Steel Piles in Clay, Sand, and Mixed Soils and Data Analysis, September 2011

In response to the mandate on Load and Resistance Factor Design (LRFD) implementations by the Federal Highway Administration (FHWA) on all new bridge projects initiated after October 1, 2007, the Iowa Highway Research Board (IHRB) sponsored these research projects to develop regional LRFD recommendations. The LRFD development was performed using the Iowa Department of Transportation (DOT) Pile Load Test database (PILOT). To increase the data points for LRFD development, develop LRFD recommendations for dynamic methods, and validate the results ofLRFD calibration, 10 full-scale field tests on the most commonly used steel H-piles (e.g., HP 10 x 42) were conducted throughout Iowa. Detailed in situ soil investigations were carried out, push-in pressure cells were installed, and laboratory soil tests were performed. Pile responses during driving, at the end of driving (EOD), and at re-strikes were monitored using the Pile Driving Analyzer (PDA), following with the CAse Pile Wave Analysis Program (CAPWAP) analysis. The hammer blow counts were recorded for Wave Equation Analysis Program (WEAP) and dynamic formulas. Static load tests (SLTs) were performed and the pile capacities were determined based on the Davisson’s criteria. The extensive experimental research studies generated important data for analytical and computational investigations. The SLT measured loaddisplacements were compared with the simulated results obtained using a model of the TZPILE program and using the modified borehole shear test method. Two analytical pile setup quantification methods, in terms of soil properties, were developed and validated. A new calibration procedure was developed to incorporate pile setup into LRFD.

Roadway Lighting and Safety: Phase II – Monitoring Quality, Durability and Efficiency, November 2011

This Phase II project follows a previous project titled Strategies to Address Nighttime Crashes at Rural, Unsignalized Intersections. Based on the results of the previous study, the Iowa Highway Research Board (IHRB) indicated interest in pursuing further research to address the quality of lighting, rather than just the presence of light, with respect to safety. The research team supplemented the literature review from the previous study, specifically addressing lighting level in terms of measurement, the relationship between light levels and safety, and lamp durability and efficiency. The Center for Transportation Research and Education (CTRE) teamed with a national research leader in roadway lighting, Virginia Tech Transportation Institute (VTTI) to collect the data. An integral instrument to the data collection efforts was the creation of the Roadway Monitoring System (RMS). The RMS allowed the research team to collect lighting data and approach information for each rural intersection identified in the previous phase. After data cleanup, the final data set contained illuminance data for 101 lighted intersections (of 137 lighted intersections in the first study). Data analysis included a robust statistical analysis based on Bayesian techniques. Average illuminance, average glare, and average uniformity ratio values were used to classify quality of lighting at the intersections.

Neutral atoms in ionic lattices: Excited states of KCl:Ag(0)

The optical-absorption spectrum of a cationic Ag0 atom in a KCl crystal has been studied theoretically by means of a series of cluster models of increasing size. Excitation energies have been determined by means of a multiconfigurational self-consistent field procedure followed by a second-order perturbation correlation treatment. Moreover results obtained within the density-functional framework are also reported. The calculations confirm the assignment of bands I and IV to transitions of the Ag-5s electron into delocalized states with mainly K-4s,4p character. Bands II and III have been assigned to internal transitions on the Ag atom, which correspond to the atomic Ag-4d to Ag-5s transition. We also determine the lowest charge transfer (CT) excitation energy and confirm the assignment of band VI to such a transition. The study of the variation of the CT excitation energy with the Ag-Cl distance R gives additional support to a large displacement of the Cl ions due to the presence of the Ag0 impurity. Moreover, from the present results, it is predicted that on passing to NaCl:Ag0 the CT onset would be out of the optical range while the 5s-5p transition would undergo a redshift of 0.3 eV. These conclusions, which underline the different character of involved orbitals, are consistent with experimental findings. The existence of a CT transition in the optical range for an atom inside an ionic host is explained by a simple model, which also accounts for the differences with the more common 3d systems. The present study sheds also some light on the R dependence of the s2-sp transitions due to s2 ions like Tl+.

Human leukocyte antigen class II variants and adult-onset asthma: does occupational allergen exposure play a role?

Recently, a locus centred on rs9273349 in the HLA-DQ region emerged from genome-wide association studies of adult-onset asthma. We aimed to further investigate the role of human leukocyte antigen (HLA) class II in adult-onset asthma and a possible interaction with occupational exposures. We imputed classical HLA-II alleles from 7579 single-nucleotide polymorphisms in 6025 subjects (1202 with adult-onset asthma) from European cohorts: ECRHS, SAPALDIA, EGEA and B58C, and from surveys of bakers and agricultural workers. Based on an asthma-specific job-exposure matrix, 2629 subjects had ever been exposed to high molecular weight (HMW) allergens. We explored associations between 23 common HLA-II alleles and adult-onset asthma, and tested for gene-environment interaction with occupational exposure to HMW allergens. Interaction was also tested for rs9273349. Marginal associations of classical HLA-II alleles and adult-onset asthma were not statistically significant. Interaction was detected between the DPB1*03:01 allele and exposure to HMW allergens (p = 0.009), in particular to latex (p = 0.01). In the unexposed group, the DPB1*03:01 allele was associated with adult-onset asthma (OR 0.67, 95%CI 0.53-0.86). HMW allergen exposures did not modify the association of rs9273349 with adult-onset asthma. Common classical HLA-II alleles were not marginally associated with adult-onset asthma. The association of latex exposure and adult-onset asthma may be modified by DPB1*03:01.

Prognostic role of KRAS and BRAF in stage II and III resected colon cancer: results of the translational study on the PETACC-3, EORTC 40993, SAKK 60-00 trial.

PURPOSE: Mutations within the KRAS proto-oncogene have predictive value but are of uncertain prognostic value in the treatment of advanced colorectal cancer. We took advantage of PETACC-3, an adjuvant trial with 3,278 patients with stage II to III colon cancer, to evaluate the prognostic value of KRAS and BRAF tumor mutation status in this setting. PATIENTS AND METHODS: Formalin-fixed paraffin-embedded tissue blocks (n = 1,564) were prospectively collected and DNA was extracted from tissue sections from 1,404 cases. Planned analysis of KRAS exon 2 and BRAF exon 15 mutations was performed by allele-specific real-time polymerase chain reaction. Survival analyses were based on univariate and multivariate proportional hazard regression models. RESULTS: KRAS and BRAF tumor mutation rates were 37.0% and 7.9%, respectively, and were not significantly different according to tumor stage. In a multivariate analysis containing stage, tumor site, nodal status, sex, age, grade, and microsatellite instability (MSI) status, KRAS mutation was associated with grade (P = .0016), while BRAF mutation was significantly associated with female sex (P = .017), and highly significantly associated with right-sided tumors, older age, high grade, and MSI-high tumors (all P < 10(-4)). In univariate and multivariate analysis, KRAS mutations did not have a major prognostic value regarding relapse-free survival (RFS) or overall survival (OS). BRAF mutation was not prognostic for RFS, but was for OS, particularly in patients with MSI-low (MSI-L) and stable (MSI-S) tumors (hazard ratio, 2.2; 95% CI, 1.4 to 3.4; P = .0003). CONCLUSION: In stage II-III colon cancer, the KRAS mutation status does not have major prognostic value. BRAF is prognostic for OS in MS-L/S tumors.

Investigation of Two Bridge Alternatives for Low Volume Roads - Phase II Volume 1 of 2 Concept 1: Steel Beam Precast Units, TR-410, 2000

This project continues the research which addresses the numerous bridge problems on the Iowa secondary road system. It is a continuation (Phase 2) of Project HR-382, in which two replacement alternatives (Concept 1: Steel Beam Precast Units and Concept 2: Modification of the Benton County Beam-in-Slab Bridge) were investigated. In previous research for concept 1, a precast unit bridge was developed through laboratory testing. The steel-beam precast unit bridge requires the fabrication of precast double-tee (PCDT) units, each consisting of two steel beams connected by a reinforced concrete deck. The weight of each PCDT unit is minimized by limiting the deck thickness to 4 in., which permits the units to be constructed off-site and then transported to the bridge site. The number of units required is a function of the width of bridge desired. Once the PCDT units are connected, a cast-in-place reinforced concrete deck is cast over the PCDT units and the bridge railing attached. Since the steel beam PCDT unit bridge design is intended primarily for use on low-volume roads, used steel beams can be utilized for a significant cost savings. In previous research for concept 2, an alternate shear connector (ASC) was developed and subjected to static loading. In this investigation, the ASC was subjected to cyclic loading in both pushout specimens and composite beam tests. Based on these tests, the fatigue strength of the ASC was determined to be significantly greater than that required in typical low volume road single span bridges. Based upon the construction and service load testing, the steel-beam precast unit bridge was successfully shown to be a viable low volume road bridge alternative. The construction process utilized standard methods resulting in a simple system that can be completed with a limited staff. Results from the service load tests indicated adequate strength for all legal loads. An inspection of the bridge one year after its construction revealed no change in the bridge's performance. Each of the systems previously described are relatively easy to construct. Use of the ASC rather than the welded studs significantly simplified the work, equipment, and materials required to develop composite action between the steel beams and the concrete deck.

Stepwise evaluation of syncope: a prospective population-based controlled study.

BACKGROUND: Evaluation of syncope remains often unstructured. The aim of the study was to assess the effectiveness of a standardized protocol designed to improve the diagnosis of syncope. METHODS: Consecutive patients with syncope presenting to the emergency departments of two primary and tertiary care hospitals over a period of 18 months underwent a two-phase evaluation including: 1) noninvasive assessment (phase I); and 2) specialized tests (phase II), if syncope remained unexplained after phase I. During phase II, the evaluation strategy was alternately left to physicians in charge of patients (control), or guided by a standardized protocol relying on cardiac status and frequency of events (intervention). The primary outcomes were the diagnostic yield of each phase, and the impact of the intervention (phase II) measured by multivariable analysis. RESULTS: Among 1725 patients with syncope, 1579 (92%) entered phase I which permitted to establish a diagnosis in 1061 (67%) of them, including mainly reflex causes and orthostatic hypotension. Five-hundred-eighteen patients (33%) were considered as having unexplained syncope and 363 (70%) entered phase II. A cause for syncope was found in 67 (38%) of 174 patients during intervention periods, compared to 18 (9%) of 189 during control (p<0.001). Compared to control periods, intervention permitted diagnosing more cardiac (8%, vs 3%, p=0.04) and reflex syncope (25% vs 6%, p<0.001), and increased the odds of identifying a cause for syncope by a factor of 4.5 (95% CI: 2.6-8.7, p<0.001). Overall, adding the diagnostic yield obtained during phase I and phase II (intervention periods) permitted establishing the cause of syncope in 76% of patients. CONCLUSION: Application of a standardized diagnostic protocol in patients with syncope improved the likelihood of identifying a cause for this symptom. Future trials should assess the efficacy of diagnosis-specific therapy.

Field Evaluation of Compaction Monitoring Technology: Phase II Volumes 1 and 2, TR-495, 2006

This report documents an extensive field program carried out to identify the relationships between soil engineering properties, as measured by various in situ devices, and the results of machine compaction monitoring using prototype compaction monitoring technology developed by Caterpillar Inc. Primary research tasks for this study include the following: (1) experimental testing and statistical analyses to evaluate machine power in terms of the engineering properties of the compacted soil (e.g., density, strength, stiffness) and (2) recommendations for using the compaction monitoring technology in practice. The compaction monitoring technology includes sensors that monitor the power consumption used to move the compaction machine, an on-board computer and display screen, and a GPS system to map the spatial location of the machine. In situ soil density, strength, and stiffness data characterized the soil at various stages of compaction. For each test strip or test area, in situ soil properties were compared directly to machine power values to establish statistical relationships. Statistical models were developed to predict soil density, strength, and stiffness from the machine power values. Field data for multiple test strips were evaluated. The R2 correlation coefficient was generally used to assess the quality of the regressions. Strong correlations were observed between averaged machine power and field measurement data. The relationships are based on the compaction model derived from laboratory data. Correlation coefficients (R2) were consistently higher for thicker lifts than for thin lifts, indicating that the depth influencing machine power response exceeds the representative lift thickness encountered under field conditions. Caterpillar Inc. compaction monitoring technology also identified localized areas of an earthwork project with weak or poorly compacted soil. The soil properties at these locations were verified using in situ test devices. This report also documents the steps required to implement the compaction monitoring technology evaluated.

Innovative Solutions for Slope Stability Reinforcement and Characterization: Vol. II, TR-489, 2005

Soil slope instability concerning highway infrastructure is an ongoing problem in Iowa, as slope failures endanger public safety and continue to result in costly repair work. While in the past extensive research has been conducted on slope stability investigations and analysis, this current research study consists of field investigations addressing both the characterization and reinforcement of such slope failures. While Volume I summarizes the research methods and findings of this study, Volume II provides procedural details for incorporating an infrequently-used testing technique, borehole shear tests, into practice. Fifteen slopes along Iowa highways were investigated, including thirteen slides (failed slopes), one unfailed slope, and one proposed embankment slope (the Sugar Creek Project). The slopes are mainly comprised of either clay shale or glacial till, and are generally gentle and of small scale, with slope angle ranging from 11 deg to 23 deg and height ranging from 6 to 23 m. Extensive field investigations and laboratory tests were performed for each slope. Field investigations included survey of slope geometry, borehole drilling, soil sampling, in-situ Borehole Shear Testing (BST) and ground water table measurement. Laboratory investigations mainly comprised of ring shear tests, soil basic property tests (grain size analysis and Atterberg limits test), mineralogy analyses, soil classifications, and natural water contents and density measurements on the representative soil samples from each slope. Extensive direct shear tests and a few triaxial compression tests and unconfined compression tests were also performed on undisturbed soil samples for the Sugar Creek Project. Based on the results of field and lab investigations, slope stability analysis was performed on each of the slopes to determine the possible factors resulting in the slope failures or to evaluate the potential slope instabilities using limit equilibrium methods. Deterministic slope analyses were performed for all the slopes. Probabilistic slope analysis and sensitivity study were also performed for the slope of the Sugar Creek Project. Results indicate that while the in-situ test rapidly provides effective shear strength parameters of soils, some training may be required for effective and appropriate use of the BST. Also, it is primarily intended to test cohesive soils and can produce erroneous results in gravelly soils. Additionally, the quality of boreholes affects test results, and disturbance to borehole walls should be minimized before test performance. A final limitation of widespread borehole shear testing may be its limited availability, as only about four to six test devices are currently being used in Iowa. Based on the data gathered in the field testing, reinforcement investigations are continued in Volume III.

Combination of bevacizumab and 2-weekly pegylated liposomal doxorubicin as first-line therapy for locally recurrent or metastatic breast cancer. A multicenter, single-arm phase II trial (SAKK 24/06).

BACKGROUND: Pegylated liposomal doxorubicin (PLD) and bevacizumab are active agents in the treatment of metastatic breast cancer (MBC). We carried out a multicenter, single-arm phase II trial to evaluate the toxicity and efficacy of PLD and bevacizumab as first-line treatment in MBC patients. METHODS: Bevacizumab (10 mg/kg) and PLD (20 mg/m(2)) were infused on days 1 and 15 of a 4-week cycle for a maximum of six cycles. Thereafter, bevacizumab monotherapy was continued at the same dose until progression or toxicity. The primary objective was safety and tolerability, and the secondary objective was to evaluate efficacy of the combination. RESULTS: Thirty-nine of 43 patients were assessable for the primary end point. Eighteen of 39 patients (46%, 95% confidence interval 30% to 63%) had a grade 3 toxicity. Sixteen (41%) had grade 3 palmar-plantar erythrodysesthesia, one had grade 3 mucositis, and one severe cardiotoxicity. Secondary end point of overall response rate among 43 assessable patients was 21%. CONCLUSIONS: In this nonrandomized single-arm trial, the combination of bimonthly PLD and bevacizumab in locally recurrent and MBC patients demonstrated higher than anticipated toxicity while exhibiting only modest activity. Based on these results, we would not consider this combination for further investigation in this setting.

Influence of magnetic field strength and image registration strategy on voxel-based morphometry in a study of Alzheimer's disease.

Multi-centre data repositories like the Alzheimer's Disease Neuroimaging Initiative (ADNI) offer a unique research platform, but pose questions concerning comparability of results when using a range of imaging protocols and data processing algorithms. The variability is mainly due to the non-quantitative character of the widely used structural T1-weighted magnetic resonance (MR) images. Although the stability of the main effect of Alzheimer's disease (AD) on brain structure across platforms and field strength has been addressed in previous studies using multi-site MR images, there are only sparse empirically-based recommendations for processing and analysis of pooled multi-centre structural MR data acquired at different magnetic field strengths (MFS). Aiming to minimise potential systematic bias when using ADNI data we investigate the specific contributions of spatial registration strategies and the impact of MFS on voxel-based morphometry in AD. We perform a whole-brain analysis within the framework of Statistical Parametric Mapping, testing for main effects of various diffeomorphic spatial registration strategies, of MFS and their interaction with disease status. Beyond the confirmation of medial temporal lobe volume loss in AD, we detect a significant impact of spatial registration strategy on estimation of AD related atrophy. Additionally, we report a significant effect of MFS on the assessment of brain anatomy (i) in the cerebellum, (ii) the precentral gyrus and (iii) the thalamus bilaterally, showing no interaction with the disease status. We provide empirical evidence in support of pooling data in multi-centre VBM studies irrespective of disease status or MFS.

Thin Maintenance Surfaces - Phase II, TR-435, 2003

In recent years there has been renewed interest in using preventive maintenance techniques to extend pavement life and to ensure low life cycle costs for our road infrastructure network. Thin maintenance surfaces can be an important part of a preventive maintenance program for asphalt cement concrete roads. The Iowa Highway Research Board has sponsored Phase Two of this research project to demonstrate the use of thin maintenance surfaces in Iowa and to develop guidelines for thin maintenance surface uses that are specific to Iowa. This report documents the results of test section construction and monitoring started in Phase One and continued in Phase Two. The report provides a recommended seal coat design process based on the McLeod method and guidance on seal coat aggregates and binders. An update on the use of local aggregates for micro-surfacing in Iowa is included. Winter maintenance guidelines for thin maintenance surfaces are reported herein. Finally, Phase One's interim, qualitative thin maintenance surface guidelines are supplemented with Phase two's revised, quantitative guidelines. When thin maintenance surfaces are properly selected and applied, they can improve the pavement surface condition index and the skid resistance of pavements. For success to occur, several requirements must be met, including proper material selection, design, application rate, workmanship, and material compatibility, as well as favorable weather during application and curing. Specific guidance and recommendations for many types of thin maintenance surfaces and conditions are included in the report.

Efficacy and Safety of Certolizumab Pegol in an Unselected Crohn's Disease Population: 26 Week Data of the FACTS II Survey.

BACKGROUND: Certolizumab pegol (Cimzia, CZP) was approved for the treatment of Crohn's disease (CD) patients in 2007 in Switzerland as first country worldwide. This prospective phase IV study aimed to evaluate the efficacy and safety of CZP over 26 weeks in a multicenter cohort of practice-based patients. METHODS: Evaluation questionnaires at baseline, week 6 and 26 were completed by gastroenterologists in hospitals and private practices. RESULTS: Sixty patients (38F/22M) were included, 53% had complicated disease (stricturing or penetrating), 45% had undergone prior CD related surgery. All patients had prior exposure to systemic steroids, 96% to immunomodulators, 73% to infliximab, and 43% to adalimumab. A significant decrease of Harvey Bradshaw Index (HBI) was observed under CZP therapy (12.24.9 at week 0 vs 6.34.7 at week 6 and 6.75.3 at week 26, both P <0.001). Response and remission rates were 70% and 40% (week 6) and 67% and 36% respectively (week 26). The complete perianal fistula closure rate was 36% at week 6 and 55% at week 26. The frequency of adverse drug reactions attributed to CZP was 5%. CZP was continued in 88% of patients beyond week 6 and in 67% beyond week 26. CONCLUSIONS: In a population of CD patients with predominantly complicated disease behaviour, CZP proved to be effective in induction and maintenance of response and remission. This series provides the first evidence of CZP's effectiveness in perianal fistulizing CD in clinical practice.

Model-based Segmentation and Image Fusion of 3D Computed Tomography and 3D Ultrasound of the Eye for Radiotherapy Planning

For radiotherapy treatment planning of retinoblastoma inchildhood, Computed Tomography (CT) represents thestandard method for tumor volume delineation, despitesome inherent limitations. CT scan is very useful inproviding information on physical density for dosecalculation and morphological volumetric information butpresents a low sensitivity in assessing the tumorviability. On the other hand, 3D ultrasound (US) allows ahigh accurate definition of the tumor volume thanks toits high spatial resolution but it is not currentlyintegrated in the treatment planning but used only fordiagnosis and follow-up. Our ultimate goal is anautomatic segmentation of gross tumor volume (GTV) in the3D US, the segmentation of the organs at risk (OAR) inthe CT and the registration of both. In this paper, wepresent some preliminary results in this direction. Wepresent 3D active contour-based segmentation of the eyeball and the lens in CT images; the presented approachincorporates the prior knowledge of the anatomy by usinga 3D geometrical eye model. The automated segmentationresults are validated by comparing with manualsegmentations. Then, for the fusion of 3D CT and USimages, we present two approaches: (i) landmark-basedtransformation, and (ii) object-based transformation thatmakes use of eye ball contour information on CT and USimages.

An EORTC Phase II study of caspofungin as first-line therapy of invasive aspergillosis in haematological patients.

OBJECTIVES: Caspofungin was evaluated as first-line monotherapy of invasive aspergillosis (IA) in patients with haematological malignancies and undergoing autologous transplants. METHODS: Adults with proven or probable IA, defined strictly according to EORTC-MSG criteria, were eligible. Those with possible IA were enrolled, but were not evaluable for efficacy unless upgraded to proven/probable disease within 7 days of registration based on investigations performed within 48 h after enrolment. Caspofungin dosage was 70 mg (day 1) followed by 50 mg/day. The primary endpoint was the proportion of patients with complete or partial response at the end of caspofungin therapy in the modified intention to treat (MITT) group; secondary endpoints were response and survival at day 84 and safety. RESULTS: In the MITT group (n = 61), 75% of patients had cancer not in remission (relapsing or refractory), 85% were neutropenic at enrolment and 49% had a Karnofsky score of < or =50. At end of treatment, 1 and 19 patients had complete and partial response, respectively [success rate 33% (20/61)], 9 (15%) achieved stabilization and 31 (51%) had disease progression. One patient was not evaluable. The 6 and 12 week survival rates were 66% (40/61) and 53% (32/60), respectively. Baseline characteristics associated with survival at day 84 were an underlying disease in remission (not relapsing or refractory) and Karnofsky score. Recovery from neutropenia at the end of treatment was also significantly associated with survival. No serious drug-related adverse events or discontinuations due to drug-related adverse events were observed. CONCLUSIONS: Caspofungin provided an observed response rate compatible with the null hypothesis of a true response rate of < or =35%. Underlying disease-related factors had a major impact on results.