Electricity, hot water and cold water production from biomass. Energetic and economical analysis of the compact system of cogeneration run with woodgas from a small downdraft gasifier

Wood gasification technologies to convert the biomass into fuel gas stand out. on the other hand, producing electrical energy from stationary engine is widely spread, and its application in rural communities where the electrical network doesn't exist is very required. The recovery of exhaust gases (engine) is a possibility that makes the system attractive when compared with the same components used to obtain individual heat such as electric power. This paper presents an energetic alternative to adapt a fixed bed gasifier with a compact cogeneration system in order to cover electrical and thermal demands in a rural area and showing an energy solution for small social communities using renewable fuels. Therefore, an energetic and economical analysis from a cogeneration system producing electric energy, hot and cold water, using wooden gas as fuel from a small-sized gasifier was calculated. The energy balance that includes the energy efficiency (electric generation as well as hot and cold water system; performance coefficient and the heat exchanger, among other items), was calculated. Considering the annual interest rates and the amortization periods, the costs of production of electrical energy, hot and cold water were calculated, taking into account the investment, the operation and the maintenance cost of the equipments. Crown Copyright (C) 2010 Published by Elsevier Ltd. All rights reserved.

DEA and DSC study of cubic silsesquioxane epoxy resin nanocomposites

Non-isothermal dielectric analysis (DEA) and differential scanning calorimetry (DSC) techniques were used to study the epoxy nanocomposites prepared by reacting 1,3,5,7,9,11,13,15-octa[dimethylsiloxypropylglycidylether] pentaciclo [9.5.1.1(3,9).1(5,15).1(7,13)] octasilsesquioxane (ODPG) with methylenedianiline (MDA). Loss factor (epsilon) and activation energy were calculated by DEA. The relationships between the loss factor, the activation energy, the structure of the network, and the mechanical properties were investigated. Activation energies determined by DEA and DSC, heat of polymerization, fracture toughness and tensile modulus show the same profile for mechanical properties with respect to ODPG content.

Linear dimensional changes of denture base and hard chair-side reline resins after disinfection

Objectives: This study evaluated the effect of disinfection by immersion in sodium perborate (50 degrees C/10 min) or microwave irradiation (650 W/6 min) on the linear dimensional change (LDC) of four reline resins (Kooliner-K, New Truliner-N, Tokuso Rebase Fast-T, Ufi Gel Hard-U) and one heat-polymerizing denture base resin (Lucitone 550-L). Methods: Specimens (50.0 mm diameter, 0.5 mm thickness) were made using a split mold with reference points, and divided into two controls and four test groups (u = 8). The distances between the points were measured on the mold (baseline readings), and compared to those obtained from the specimens after: polymerization or immersion in water (37 degrees C) for 7 days (controls); 2 or 7 cycles of disinfection by immersion or microwave irradiation. Results: the two-way ANOVA and Tukey's test (alpha = 0.05) showed that microwave disinfection significantly increased the mean LDC of materials L (-1.43%), N (-1.27%) and K (-1.06%). Material N also exhibited a significant increase in LDC after two cycles of chemical disinfection (-0.73%). For U (-0.47%) and T (-0.21%) materials, no significant changes in LDC were found. Conclusions: Microwave disinfection increases the shrinkage of materials L, N, and K. The dimensional stability of resins U and T was not affected by the disinfection methods evaluated. (c) 2006 Wiley Periodicals, Inc.

Bonding strength between a hard chairside reline resin and a denture base material as influenced by surface treatment

Direct relining of dentures made with hard chairside reline resins is faster than laboratory-processed reline systems and the patient is not without the prosthesis for the time necessary to perform the laboratory procedures. However, a weak bond between the autopolymerizing acrylic reline resins and the denture base material has been observed. This study evaluated the effect of six different surface treatments on the bond strength between a hard chairside reline acrylic resin and ia heat-cured acrylic resin. Specimens of the heat-cured acrylic resin were divided into seven groups. one of these groups remained intact. In the other groups, a 10-mm square section was removed from the centre of each specimen. The bonding surfaces were then treated with (i) methyl methacrylate monomer, (ii) isobutyl methacrylate monomer, (iii) chloroform, (iv) acetone, (v) experimental adhesive and (vi) no surface treatment-control group. Kooliner acrylic resin was packed,into the square sections and polymerized. The bonding strength was evaluated by a three-point loading test. The results were submitted to one-way analysis of variance (ANOVA) followed by a Tukey multiple range test at a 5% level of significance. No significant difference was found between the surface treatment with Lucitone 550 monomer or chloroform, but both were stronger than the majority of the other groups. The bond strength provided by all the surface treatments was lower than that of the intact heat-cured resin.

HARDNESS and SURFACE ROUGHNESS of RELINE and DENTURE BASE ACRYLIC RESINS AFTER REPEATED DISINFECTION PROCEDURES

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

SIRT1 Deacetylase Activity and the Maintenance of Protein Homeostasis in Response to Stress: An Overview

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Metal fluxes at the sediment-water interface in rivers in the Turvo/Grande drainage basin, So Paulo State, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

cAMP signaling pathway controls glycogen metabolism in Neurospora crassa by regulating the glycogen synthase gene expression and phosphorylation

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Very Intense Distinct Blue and Red Photoluminescence Emission in MgTiO3 Thin Films Prepared by the Polymeric Precursor Method: An Experimental and Theoretical Approach

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of recycled tiles and OSB ceiling materials in closed broiler house prototypes

This study aimed at evaluating the thermal performance of a modular ceiling system for poultry houses. The reduced- and distorted-scale prototypes used ceiling modules made of reforested wood and were covered with recycled long-life package tiles. The following parameters were measured for 21 days: tile internal surface temperature (ST), globe temperature and humidity index (WBGT), and radiant heat load (RHL). Measurements were made at times of highest heat load (11:00 am, 13:00 pm, and 03:00 pm). Collected data were analyzed by R statistics software. Means were compared by multiple comparison test (Tukey) and linear regression was performed, both at 5% significance level. The results showed that the prototype with the ceiling was more efficient to reduce internal tile surface temperature; however, this was not sufficient to provide a comfortable environment for broilers during the growout. Therefore, other techniques to provide proper cooling are required in addition to the ceiling.

Efeitos da temperatura e da movimentação do ar sobre o isolamento térmico do velo de ovinos em câmara climática

Foram utilizados dez ovinos da raça Corriedale - cinco machos e cinco fêmeas com pesos entre 52,2 e 87,6 kg - com o objetivo de avaliar o efeito da combinação da movimentação do ar (0 e 5,0 m/s) com a temperatura do ar (25, 30 e 40ºC) sobre a temperatura retal (T R, ºC), da epiderme (T E, ºC), da superfície do velo (T V, ºC) e do interior do velo (T I, ºC) e a espessura do velo (E V, cm) e suas relações com o isolamento térmico do velo. A presença de vento não teve efeito sobre as variáveis estudadas, o que sugere que fluxo de ar (<5,0 m/s) paralelo ao eixo corporal do animal tem pouco efeito sobre o isolamento térmico do velo, independentemente da temperatura do ar, que se mostrou altamente correlacionada, de forma positiva, com as temperaturas retal, do velo, do interior do velo e da epiderme. Sob temperaturas inferiores a 30ºC, a transferência de calor através do velo ocorreu via condução e convecção livre, enquanto sob altas temperaturas (>40ºC) o fluxo de calor sensível não foi significativa.

THERMAL REGIME AND STABILITY OF JURUMIRIM RESERVOIR (PARANAPANEMA RIVER, SAO-PAULO, BRAZIL)

Thermal regime and stability in Jurumirim Reservoir (São Paulo, Brazil) were studied for a year. Isothermy and thermal stratification were observed from June to September and from October to March, respectively. The annual heat budget was 14.0 Kcal . cm-2 and average heat gain per day was 67.2 cal . cm-2 . day-1. Maximum stability and wind work reached 324.2 and 3,037.5 g . cm . cm-2, respectively. According to thermal structure and heat content, Jurumirim Reservoir was classified as a warm tropical monomictic lake.

Hair coat characteristics and sweating rate of Braford cows in Brazil

This paper deals with the effects of hair coat characteristics on the sweating rate of Brazilian Braford cows and estimation of heritabilities and genetic correlations of these traits. Data (n=1607) on hair length, coat thickness, hair diameter, number of hairs per unit area, coat reflectance and sweating rate were recorded from heifers and cows of a commercial herd managed on range under extensive system. The data were analyzed considering the following effects on the model for hair coat traits: classes of sires and contemporary groups; linear effects of month and genotype; linear and quadratic effects of age. The effect of sire was important (P<0.05) for all hair coat traits, except for number of hairs; contemporary groups affected (P<0.05) all hair coat traits; the effect of sampling month was important (P<0.05) for hair length and reflectance; genotype affected (P<0.05) hair length, diameter and coat reflectance; the quadratic effect of age was important (P<0.05) only for coat reflectance. Two models were used to analyze the sweating rate. The first model considered the following fixed effects: classes of contemporary groups and sires; linear effect of genotype, coat thickness, hair length, hair diameter, number of hairs, coat reflectance; linear and quadratic effects of time of day, age, air temperature, partial vapour pressure and radiant heat load. The second model used for the sweating rate considered the same fixed effects for the first model, except that the hair coat characteristics were adjusted for important effects used in the models to analyze hair coat traits. All meteorological factors and contemporary groups were important (P<0.05) on variation of sweating rate in both models. The Restricted Maximum. Likelihood (REML) method was used to estimate variance and covariance components under the sire model. Results included heritability estimates in narrow (h(2)) and broad (H) sense for single-trait analyzes: hair thickness (h(2)=0.16; H-2=0.26); hair length (h(2)=0.18; H-2=0.39); number of hairs (h(2)=0.08 +/- 0.07; H-2=0.08 +/- 0.07); hair diameter (h(2)=0.12 +/- 0.07; H-2=0.12 +/- 0.07); coat reflectance (h(2)=0.30; H-2=0.42); and sweating rate (h(2)=0.10 +/- 0.07; H-2=0.10 +/- 0.07). In general, the genetic correlations between the adaptive traits were favorable as for the direction to select for adaptation in tropical environment; however, they presented high standard errors. The results of this study imply that hair coat characteristics and sweating ability are important for the adaptability to heat stress and they must be better studied and further considered for selection for genetic progress of adaptation in tropical environment. (C) 2007 Elsevier B.V All rights reserved.

Er3+ and Eu3+ containing transparent glass ceramics in the system PbGeO3-PbF2-CdF2

Glasses with composition 60PbGeO(3)-10PbF(2)-30CdF(2) (mol%) have been obtained in the bulk form with a high stability against crystallization. After doping them with 0.5 mol% of Er3+ or Eu3+ and appropriate heat treatment transparent glass ceramics could be obtained. Electronic spectroscopy, X-ray diffraction and transmission electron microscopy measurements have been made. beta-PbF2: Er3+/Eu3+ Single crystals, 5-10 nm in size, are detected in the otherwise transparent composite medium, the size of the particles and absence of clustering allowing for the increased transparency of the final materials. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Effects of synthesis and processing on supersaturated rare earth-doped nanometric SnO2 powders

This paper presents and discusses some of the results of the effects of processing on rare earth-doped nanosize SnO2. Several relevant factors that may influence the characteristics of the final product are studied. The influence of two preparation routes and two heat-treatment conditions on the incorporation of dopants is investigated. The route whereby a soluble salt is used as the dopant source is found to provide the highest degree of dopant incorporation, even under the least favorable heat-treatment conditions.