908 resultados para LC-MSMS
Resumo:
The bioassay-guided purification of ethanolic extracts from inflorescences of Piper subtomentosum Trel. & Yunck and aerial part of Piper septuplinervium (Miq. ) C. DC. led to isolation of five flavonoids, uvangoletin (1), galangin (2), chrysin (5), 5-hydroxy-4',7-dimethoxy-flavone (6), pinostrobin (7); one amide, N-p-coumaroil-tyramine (4); one acylglycerol, monopalmitin (3); one derivative of acid, protocatechuic acid (8); and glycosydated sterol, daucosterol (9). Their structures were elucidated on the basis of spectroscopy and spectrometry data and by comparison with data reported in the literature. The isolated compounds were tested against Spodoptera frugiperda. The results showed galangin and protocatechuic acid to be the most active (LC 50 13.63 and 17.16 ppm, respectively).
Resumo:
A simple procedure based on stir bar sorptive extraction and high-performance liquid chromatography-ultraviolet/photodiode array detection (SBSE/LC-UV/PAD) to determine intermediates and by-products of esfenvalerate is described. The influence of organic modifier, ionic strength, extraction time, temperature and pH were simultaneously evaluated by using a factorial experimental design. The utilization of different organic solvents and desorption times were also investigated to establish the optimal conditions for SBSE liquid desorption. Among the ten different peaks (intermediates and by-products) detected after degradation of esfenvalerate, eight (including 3-phenoxybenzoic acid and 3-phenoxybenzaldehyde) were successfully extracted by SBSE under the optimized conditions.
Resumo:
A procedure was developed for determination of 5 sedatives and 14 β-blockers in swine kidney and subsequent analysis by liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS). Three different procedures for extraction were tested, evaluated through recovery studies. The procedure using acetonitrile for extraction and cleanup with freezing at low temperature and dispersive solid phase extraction using 500 mg celite® 545 before the concentration step presented the better results. The dried samples were redissolved with methanol and analyzed using a LC-MS/MS system with electrospray ionization (ESI) operating in positive MRM mode. The recovery values for this procedure were in the 75-88% range. The robustness of the method was tested against small variations. The method was used to analyze carazolol, azaperone and azaperol in collaborative assay, obtaining results close to designed value.
Resumo:
Liquid chromatography is often used for the determination of pesticide multiresidues in foods. In Brazil, the strawberry crop is an example of a food with high levels of irregularities because of the application of pesticides. This is a major concern from the perspective of food safety, environmental protection, and certification for food export. The purpose of this study is to evaluate and compare chromatographic separation and detection methods in relation to a newly developed and validated method using ultra high performance liquid chromatography (LC) coupled with tandem mass spectrometry (MS/MS) for the analytical determination of pesticides in strawberries. The comparisons were based on evaluations of the analysis time, consumption of the solvent in the mobile phase, injection volume, detectability, matrix effect, and recovery. The results showed that the LC–MS/MS and UHPLC–MS/MS techniques were both extremely efficient at analyzing pesticide residues with different physico-chemical parameters that were present at low concentrations in a complex matrix. The UHPLC separation method provided better chromatographic performance and productivity, which contributed favorably to routine analytical determinations. Detection by MS/MS had better detectability and selectivity compared with the diode array detector.
Resumo:
Suomessa sähkönjakeluverkko koostuu pääasiassa 20 kV ja 400 V jännitetasoista. Tällöin sähkö viedään lähelle kuluttajia suuremmalla jännitetasolla ja muunnetaan alhaisemmaksi lähellä asiakkaita. Haittapuolena on se, että haja-asutusalueilla jakelumuuntajien määrä kasvaa suureksi, koska ne täytyy sijoittaa lähelle kuluttajaa. Vaihtoehtona on toteuttaa osa sähkönjakelusta tasajännitteellä, jolloin tehollinen jännite olisi suurempi. Tällöin sähköä voitaisiin siirtää pidempiä matkoja ilman, että asiakaskohtaisia tai muutaman asiakkaan kattavia 20 kV siirtolinjoja tarvitsisi käyttää. Tämä taasen edellyttää asiakaskohtaisien vaihtosuuntaajien käyttöä. Tässä työssä esiteltävällä 1 kVA vaihtosuuntaajalla muodostetaan tasasähköjakeluverkosta saatavasta 750 V tasasähköstä yksivaiheista (230 VRMS, 50 Hz) verkkojännitettä. Laite on suunniteltu toteuttamaan galvaaninen erotus mahdollisimman hyvän hyötysuhteen puitteissa. Vaihtosuuntaaja on toteutettu käyttämällä resonanssikonvertteria, joka vaihtosuuntaa jakelujännitteen korkeataajuiseksi vaihtojännitteeksi. Tämän jälkeen toteutetaan galvaaninen erotus käyttäen suurtaajuusmuuntajaa. Tätä seuraa syklokonvertteri, joka pulssintiheysmodulaatiota soveltaen muodostaa lähtöjännitteen. Tämä suodatetaan lopuksi LC- alipäästösuotimella säröltään standardin mukaiseksi. Laite on jaettu työssä kolmeen osaan, joista jokaisen toiminta on selitetty ja simuloitu itsenäisesti. Lopussa koko järjestelmä on simuloitu yhtenä kokonaisuutena. Hyötysuhteeksi arvioitiin karkeasti 94 % ja lopullisista tuloksista voidaan päätellä, että laitteen toteuttaminen prototyypiksi voisi olla kannattavaa.
Resumo:
The aim of the thesis is to investigate the hybrid LC filter behavior in modern power drives; to analyze the influence of such a du/dt filter on the control system stability. With the implementation of the inverter output RLC filter the motor control becomes more complicated. And during the design process the influence of the filter on the motor should be considered and the filter RLC parameters should be constrained.
Resumo:
The human genome comprises roughly 20 000 protein coding genes. Proteins are the building material for cells and tissues, and proteins are functional compounds having an important role in many cellular responses, such as cell signalling. In multicellular organisms such as humans, cells need to communicate with each other in order to maintain a normal function of the tissues within the body. This complex signalling between and within cells is transferred by proteins and their post-translational modifications, one of the most important being phosphorylation. The work presented here concerns the development and use of tools for phosphorylation analysis. Mass spectrometers have become essential tools to study proteins and proteomes. In mass spectrometry oriented proteomics, proteins can be identified and their post-translational modifications can be studied. In this Ph.D. thesis the objectives were to improve the robustness of sample handling methods prior to mass spectrometry analysis for peptides and their phosphorylation status. The focus was to develop strategies that enable acquisition of more MS measurements per sample, higher quality MS spectra and simplified and rapid enrichment procedures for phosphopeptides. Furthermore, an objective was to apply these methods to characterize phosphorylation sites of phosphopeptides. In these studies a new MALDI matrix was developed which allowed more homogenous, intense and durable signals to be acquired when compared to traditional CHCA matrix. This new matrix along with other matrices was subsequently used to develop a new method that combines multiple spectra from different matrises from identical peptides. With this approach it was possible to identify more phosphopeptides than with conventional LC/ESI-MS/MS methods, and to use 5 times less sample. Also, phosphopeptide affinity MALDI target was prepared to capture and immobilise phosphopeptides from a standard peptide mixture while maintaining their spatial orientation. In addition a new protocol utilizing commercially available conductive glass slides was developed that enabled fast and sensitive phosphopeptide purification. This protocol was applied to characterize the in vivo phosphorylation of a signalling protein, NFATc1. Evidence for 12 phosphorylation sites were found, and many of those were found in multiply phosphorylated peptides
Resumo:
In recent years, the network vulnerability to natural hazards has been noticed. Moreover, operating on the limits of the network transmission capabilities have resulted in major outages during the past decade. One of the reasons for operating on these limits is that the network has become outdated. Therefore, new technical solutions are studied that could provide more reliable and more energy efficient power distributionand also a better profitability for the network owner. It is the development and price of power electronics that have made the DC distribution an attractive alternative again. In this doctoral thesis, one type of a low-voltage DC distribution system is investigated. Morespecifically, it is studied which current technological solutions, used at the customer-end, could provide better power quality for the customer when compared with the current system. To study the effect of a DC network on the customer-end power quality, a bipolar DC network model is derived. The model can also be used to identify the supply parameters when the V/kW ratio is approximately known. Although the model provides knowledge of the average behavior, it is shown that the instantaneous DC voltage ripple should be limited. The guidelines to choose an appropriate capacitance value for the capacitor located at the input DC terminals of the customer-end are given. Also the structure of the customer-end is considered. A comparison between the most common solutions is made based on their cost, energy efficiency, and reliability. In the comparison, special attention is paid to the passive filtering solutions since the filter is considered a crucial element when the lifetime expenses are determined. It is found out that the filter topology most commonly used today, namely the LC filter, does not provide economical advantage over the hybrid filter structure. Finally, some of the typical control system solutions are introduced and their shortcomings are presented. As a solution to the customer-end voltage regulation problem, an observer-based control scheme is proposed. It is shown how different control system structures affect the performance. The performance meeting the requirements is achieved by using only one output measurement, when operating in a rigid network. Similar performance can be achieved in a weak grid by DC voltage measurement. An additional improvement can be achieved when an adaptive gain scheduling-based control is introduced. As a conclusion, the final power quality is determined by a sum of various factors, and the thesis provides the guidelines for designing the system that improves the power quality experienced by the customer.
Resumo:
O fungo Cylindrocladium spathiphylli causa podridão no colo e nas raízes de espatifilo, induzindo amarelecimento e murcha nas folhas da parte aérea. Há poucos estudos com o fungo quanto às enzimas extracelulares. Assim, delineou-se ensaio inteiramente casualizado in vitro, com três tratamentos (dois isolados normais: LFEEI016 - EPAGRI/SC e MMBF 01/01 - IB/SP; mais testemunha) e seis repetições, visando a detecção de enzimas. A amilase (AM), lipase (LP), carboximetilcelulase (CMC) e lacase (LC) foram mensuradas pelo cálculo da área da coroa circular, local de atividade das enzimas. A catalase (CT) e gelatinase (GL) foram mensuradas por símbolos, depois transformados em notas (1 a 4, de ausência à intensa produção). O isolado MMBF 01/01 produziu as maiores áreas e com mais intensidade as enzimas. Das enzimas, a maior área foi a da LC e depois a LP. LFEEI016 e MMBF 01/01 não apresentaram área para AM e CMC e exibiram intensidade fraca e igual para CT. A intensidade de GT foi moderada no MMBF 01/01 (nota média 3,0) e ausente para o LFEEI016 (nota média 1,0). Após a produção das enzimas extracelulares, os isolados foram alterados vegetativamente por temperatura. Instalou-se ensaio inteiramente ao acaso, em fatorial contendo disco de micélio dos isolados do fungo versus três temperaturas [23ºC (T1); 33ºC (T2) e de 33ºC para 23ºC (T3)] versus quatro períodos (3; 6; 9 e 12 dias), com oito repetições, em placa de Petri com BDA mantida em BOD. O diâmetro das colônias foi medido diariamente (mm) em dois sentidos. As alterações de temperatura vistas foram: inócuo, fungistático (FS) e fungicida (FC). Aplicou-se estatística nas temperaturas T1 e T3 dos isolados para checar efeito FS e escolher aqueles com maior e menor efeito. O isolado LFEEIO16 mostrou efeito FS com três dias às temperaturas 33ºC e de 33ºC para 23ºC. Nos demais períodos, o isolado sofreu efeito FC. O MMBF 01/01 mostrou efeito FS em todos os períodos. Ambos isolados sofreram, estatisticamente, efeito FS. O MMBF 01/01 mostrou maior efeito FS aos nove dias, nas temperaturas referidas e menor com três dias. Após a constatação de alteração na taxa de crescimento micelial dos isolados, procurou-se verificar, novamente, a produção de enzimas extracelulares. Os isolados alterados e utilizados foram o MMBF 01/01 com três e nove dias e o LFEEIO16 com três dias. A produção e a avaliação das enzimas foram realizadas da mesma maneira para os isolados normais. O isolado MMBF 01/01 - três dias produziu as maiores áreas e com mais intensidade as enzimas. Das enzimas, a maior área foi a da LC. Após LC, a área da LP foi maior que a da CMC nos isolados. Não se detectou área de AM nos isolados. A intensidade de GL foi maior que a da CT nos isolados MMBF 01/01 com três e nove dias. Para LFEEI016 - três dias, a intensidade média de CT foi nota 2,0 e ausência de GL (nota média 1,3). Sugere-se investigar a severidade da doença na planta entre os isolados e em condições naturais investigar a evolução da LC em comparação as demais enzimas na patogênese do fungo na cultura.
Resumo:
This study aimed at quantifying total organic carbon stocks and its pools in Acrisol under agroforestry systems with six (AFS6) and thirteen years old (AFS13), slash-and-burn agriculture (SBA) and savanna native forest (SNF) in northeastern Brazil. Soil samples were collected at 0-0.05 m, 0.05-0.10 m, 0.10-0.20 m and 0.20-0.40 m depths in the dry and rainy seasons to evaluate total organic carbon (TOC) stocks and labile carbon (LC), fulvic acid fraction (C-FAF), humic acid fraction (C-HAF), humin (C-HF) and microbial biomass carbon (Cmic) contents. Additionally, carbon management index (CMI) was determined. Higher TOC stocks (97.7 and 81.8 Mg ha-1 for the 0-0.40 m depth in the dry and rainy seasons, respectively) and LC, humic substances and Cmic contents were observed in the AFS13 in all the depths. CMI also was higher in the AFS13 (0-0. 05 m: 158 and 86; 0.05-0.10 m: 171 and 67, respectively for the dry and rainy seasons) especially when compared to the SBA (0-0.05 m: 5.6 and 5.4; 0.05-0.10 m: 5.3 and 5.8, respectively for dry and rainy seasons). The agroforestry systems increased soil quality through the conservation of organic matter and can be considered an excellent strategy to assurance sustainability in tropical soil of Northeastern Brazil
Resumo:
The aim of this study was to identify, by multivariate statistical technique, the physic, chemical and biological variables that best characterize the quality of surface waters in two small rural catchments with different land uses (eucalyptus silviculture (SC) vs. pasture and extensive livestock (LC)) located in Rosário do Sul, RS - Brazil. Monitoring was conducted during the months of August 2011 to August 2012 and the following parameters were analyzed: Ca2+, Mg2+, K+, SO42-, Cl-, pH, electrical conductivity, turbidity, alkalinity, suspended and dissolved solids, biochemical oxygen demand , total coliforms, Escherichia coli and temperature, flow and rainfall. Through the use of FA/PCA, it was found that the model best fit to express water quality of in LC that was composed of five factors which account for 83.5% of the total variance, while for SC, four factors accounted for 85.12% of the variance. In LC, the five main factors were, respectively, soluble salts, diffuse pollution, solid, and both anthropogenic and organic factors. In SC, the four factors were namely: soluble salts, mineral, nutritional and diffuse pollution factors. The results of this study showed that by replacing the traditional soil usage (pasture and livestock) with planted forest, diffuse pollution was attenuated but, however, it did not result in major changes in the physical-chemical and biological characteristics of the water. Another point to note is that factorial analysis did not result in a large reduction in the number of variables, once the best model fit occurred with the addition of 15 of 18 analyzed variables (LC) and 17 of 18 analyzed variables (SC).
Resumo:
Os solos submetidos a sistemas de produção que não incluem o preparo do solo, estão condicionados, em sua sustentabilidade, a um manejo que priorize o acompanhamento da compactação que o tráfego de máquinas provoca. Foram realizados ensaios de campo com o objetivo de avaliar a reologia de um solo Typic Hapludert, submetido ao tráfego de veículos em dois sistemas de preparo do solo (preparo convencional - LC, e semeadura direta - SD). Os subtratamentos foram quatro intensidades de tráfego (0; 80; 160 e 240 Mg km ha-1). As variáveis experimentais dependentes foram: índice de cone (IC) e densidade aparente a seco (DA). Para 160 e 240 Mg km ha-1, encontraram-se diferenças estatísticas significativas no IC em relação à testemunha. Para o LC, com as maiores intensidades de tráfego, encontraram-se valores de DA superiores a 1,83 Mg m-3. O comportamento mecânico do solo sob tráfego é mais diferente em SD que em LC. Existe uma relação direta entre o número de passadas e a profundidade onde se localiza a camada de maior resistência à penetração nos solos sob tratamento com LC.
Resumo:
Frequency converters are widely used in the industry to enable better controllability and efficiency of variable speed AC motor drives. Despite these advantages, certain challenges concerning the inverter and motor interfacing have been present for decades. As insulated gate bipolar transistors entered the market, the inverter output voltage transition rate significantly increased compared with their predecessors. Inverters operate based on pulse width modulation of the output voltage, and the steep voltage edge fed by the inverter produces a motor terminal overvoltage. The overvoltage causes extra stress to the motor insulation, which may lead to a prematuremotor failure. The overvoltage is not generated by the inverter alone, but also by the sum effect of the motor cable length and the impedance mismatch between the cable and the motor. Many solutions have been shown to limit the overvoltage, and the mainstream products focus on passive filters. This doctoral thesis studies an alternative methodology for motor overvoltage reduction. The focus is on minimization of the passive filter dimensions, physical and electrical, or better yet, on operation without any filter. This is achieved by additional inverter control and modulation. The studied methods are implemented on different inverter topologies, varying in nominal voltage and current.For two-level inverters, the studied method is termed active du/dt. It consists of a small output LC filter, which is controlled by an independent modulator. The overvoltage is limited by a reduced voltage transition rate. For multilevel inverters, an overvoltage mitigation method operating without a passive filter, called edge modulation, is implemented. The method uses the capability of the inverter to produce two switching operations in the same direction to cancel the oscillating voltages of opposite phases. For parallel inverters, two methods are studied. They are both intended for two-level inverters, but the first uses individual motor cables from each inverter while the other topology applies output inductors. The overvoltage is reduced by interleaving the switching operations to produce a similar oscillation accumulation as with the edge modulation. The implementation of these methods is discussed in detail, and the necessary modifications to the control system of the inverter are presented. Each method is experimentally verified by operating industrial frequency converters with the modified control. All the methods are found feasible, and they provide sufficient overvoltage protection. The limitations and challenges brought about by the methods are discussed.
Comparison between open and laparoscopic elective cholecystectomy in elderly, in a teaching hospital
Resumo:
Objective: to analyze the differences in mortality rates, length of hospital stay, time of surgery and the conversion rate between elective open cholecystectomies (OC) and laparoscopic ones (LC) in elderly patients. Methods : we evaluated medical records of patients 65 years of age or older undergoing open or laparoscopic cholecystectomy at the Hospital Regional de Mato Grosso do Sul between January 2008 and December 2011. We excluded individuals operated in non-elective scenarios or who underwent intraoperative cholangiography. Results : we studied 113 patients, of whom 38.1% were submitted to the OC and 61.9%, to LC. Women accounted for 69% of patients and men, for 31%. The conversion rate was 2.9%. The mean age and duration of the procudure was 70.1 and 84 minutes, respectively, with no significant difference between OC and LC. Patients undergoing LC had shorter hospital stays (2.01 versus 2.95 days, p=0.0001). We identified operative complications in sixpatients (14%) after OC and in nine (12%) after LC, with no statistical difference. Conclusion : there was no difference in morbidity and mortality when comparing OC with LC. The laparoscopic approach led to shorter hospital stay. Operative time did not differ between the two access routes. The conversion rate was similar to other studies.
Resumo:
O Grupo Mycoplasma mycoides (GMM) foi diagnosticado por PCR-REA e imunoperoxidase indireta (IPI) em amostras de lavados de conduto auditivo de bovinos no Estado do Rio de Janeiro, Brasil. 60 bovinos foram selecionados aleatoriamente. As lavagens foram feitas com uso de seringas estéreis contendo um volume de 60 mL de solução salina tamponada (PBS pH 7.2). As amostras obtidas foram estocadas em glicerol (1:2) e congeladas a 20ºC até uso. Estas amostras foram diluídas até 10-5 e repicadas em meio Hayflick modificado, sólido e líquido, sendo incubados a 37ºC por 48-72 horas. As placas foram mantidas em microaerofilia e observadas diariamente, para visualização das colônias típicas em ovo-frito. Das 60 amostras cultivadas, 48 (80,00%) foram positivas para Mycoplasma spp. A prevalência obtida para o GMM na IPI foi de 20,0% (12/60) enquanto na PCR-REA foi de 41,7% (25/60). Das cepas tipificadas pela IPI 58,3% (7/12) foram M. mycoides subsp. mycoides LC e 41,7% (5/12) foram M. capricolum. Na PCR-REA o grupo M. mycoides foi confirmado pela visualização de um amplicon de 785bp, compatível com este grupo. O valor encontrado no teste Kappa para associação entre estes testes foi de 0,14 (P>0,05. Na clivagem do produto da PCR com a enzima de restrição AluI, de cepas de referências e dos isolados de ouvido os fragmentos obtidos foram de 81, 98, 186 e 236pb, mas não de 370pb, que é específica para o agente da Pleuropneumonia Contagiosa Bovina. A presença de espécies de micoplasmas no conduto auditivo de bovinos assintomáticos representa um risco para propagação de Mycoplasma spp. entre rebanhos bovinos no Brasil.