Geochemistry of fluoride rich groundwater in Kolar and Tumkur Districts of Karnataka

Groundwater is a significant water resource in India for domestic, irrigation, and industrial needs. By far the most serious natural groundwater-quality problem in India, in terms of public health, derives from high fluoride, arsenic, and iron concentrations. Hydrogeochemical investigation of fluoride contaminated groundwater samples from Kolar and Tumkur Districts in Karnataka are undertaken to understand the quality and potability of groundwater from the study area, the level of fluoride contamination, the origin and geochemical mechanisms driving the fluoride enrichment. Majority of the groundwater samples did not meet the potable water criteria as they contained excess (>1.5 mg/L) fluoride, dissolved salts (>500 mg/L) and total hardness (75-924 mg/L). Hydrogeochemical facies of the groundwater samples suggest that rock weathering and evaporation-crystallization control the groundwater composition in the study area with 50-67% of samples belonging to the Ca-HCO3 type and the remaining falling into the mixed Ca-Na-HCO3 or Ca-Mg-Cl type. The saturation index values indicated that the groundwater in the study area is oversaturated with respect to calcite and under-saturated with respect to fluorite. The deficiency of calcium ion concentration in the groundwater from calcite precipitation favors fluorite dissolution leading to excess fluoride concentration.

Prospects for wind energy utilisation in Karnataka State

An examination of the data available at 22 meteorological stations in Karnataka State shows that wind velocities in the State as a whole are neither spectacularly high nor negligibly low. The highest winds (annual mean of around 13 km/hr) are experienced in parts of the northern maidan region of the State (Gulbarga, Raichur and Bidar districts) and in Bangalore. The winds are strongly seasonal: typically, the five monsoon months May-September account for about 80% of the annual wind energy flux. Although the data available are inadequate to make precise estimates, they indicate that the total wind energy potential of the State is about an order of magnitude higher than the current electrical energy consumption. The possible exploitation of wind energy for applications in rural areas therefore requires serious consideration, but it is argued that to be successful it is essential to formulate an integrated and carefully planned programme. The output of current windpumps needs to be increased; a doubling should be feasible by the design of suitable load-matching devices. The first cost has to be reduced by careful design, by the use of local materials and skills and by employing a labour-intensive technology. A consideration of the agricultural factors in the northern maidan region of the State shows that there is likely to be a strong need for mechanical assistance in supplemental and life-saving irrigation for the dry crops characteristic of the area. A technological target for a windmill that could find applications in this area would be one with a rotor diameter of about 10 m that can lift about 10,000 litres of water per hour in winds of 10 km/hr (2.8 m/s) hourly average speed and costs less than about Rs 10,000. Although no such windmills exist as of today, the authors believe that achievement of this target is feasible. An examination of various possible scenarios for the use of windmills in this area suggests that with a windpump costing about Rs 12,000, a three hectare farm growing two dry crops a year can expect an annual return of about 150% from an initial investment of about Rs 15,000. It is concluded that it should be highly worthwhile to undertake a coordinated programme for wind energy development that will include more detailed wind surveys in the northern maidan area (as well as some others, such as the Western Ghats), the development of suitable windmill designs and a study of their applications to agriculture as well as to other fields.

Inverted V-Notch: Practical Proportional Weir

This paper presents a practical linear proportional weir of simple geometric shape in the form of an inverted V-notch or inward trapezium. The flow through this weir, of half-width w and altitude d, for depths above 0.22d is proportional to the depth of flow measured above a reference plane situated at 0.08d for all heads in the range 0.22d<=h<=0.94d, with a maximum percentage deviation of ±1.5 from the theoretical discharge. The linear relationship between head and discharge is based on numerical optimization procedures. Nearly 75% of the depth of inverted V-notch can be used effectively as the measuring range. Experiments with four weirs, with different vertex angles, show excellent agreement with the theory by giving an average coefficient of discharge for each weir varying from 0.61–0.62.

COMMON-Sense net:Improved water management for resource-poor farmers via sensor networks

We describe the on-going design and implementation of a sensor network for agricultural management targeted at resource-poor farmers in India. Our focus on semi-arid regions led us to concentrate on water-related issues. Throughout 2004, we carried out a survey on the information needs of the population living in a cluster of villages in our study area. The results highlighted the potential that environment-related information has for the improvement of farming strategies in the face of highly variable conditions, in particular for risk management strategies (choice of crop varieties, sowing and harvest periods, prevention of pests and diseases, efficient use of irrigation water etc.). This leads us to advocate an original use of Information and Communication Technologies (ICT). We believe our demand-driven approach for the design of appropriate ICT tools that are targeted at the resource-poor to be relatively new. In order to go beyond a pure technocratic approach, we adopted an iterative, participatory methodology.

Sadetuksesta ja siihen liittyvistä tekijöistä erityisesti Kiskon seudulla

English summary: On irrigation in Southwestern Finland

Functional Surfaces for Microfluidics in Proteomic Analysis

Microchips for use in biomolecular analysis show a lot of promise for medical diagnostics and biomedical basic research. Among the potential advantages are more sensitive and faster analyses as well as reduced cost and sample consumption. Due to scaling laws, the surface are to volume ratios of microfluidic chips is very high. Because of this, tailoring the surface properties and surface functionalization are very important technical issues for microchip development. This thesis studies two different types of functional surfaces, surfaces for open surface capillary microfluidics and surfaces for surface assisted laser desorption ionization mass spectrometry, and combinations thereof. Open surface capillary microfluidics can be used to transport and control liquid samples on easily accessible open surfaces simply based on surface forces, without any connections to pumps or electrical power sources. Capillary filling of open partially wetting grooves is shown to be possible with certain geometries, aspect ratios and contact angles, and a theoretical model is developed to identify complete channel filling domains, as well as partial filling domains. On the other hand, partially wetting surfaces with triangular microstructures can be used for achieving directional wetting, where the water droplets do not spread isotropically, but instead only spread to a predetermined sector. Furthermore, by patterning completely wetting and superhydrophobic areas on the same surface, complex droplet shapes are achieved, as the water stretches to make contact with the wetting surface, but does not enter into the superhydrophobic domains. Surfaces for surface assisted laser desorption ionization mass spectrometry are developed by applying various active thin film coatings on multiple substrates, in order to separate surface and bulk effects. Clear differences are observed between both surface and substrate layers. The best performance surfaces consisted of amorphous silicon coating and an inorganic-organic hybrid substrate, with nanopillars and nanopores. These surfaces are used for matrix-free ionization of drugs, peptides and proteins, and for some analytes, the detection limits were in the high attomoles. Microfluidics and laser desorption ionization surfaces are combined on a functionalized drying platforms, where the surface is used to control the shape of the deposited analyte droplet, and the shape of the initial analyte droplet affects the dried droplet solute deposition pattern. The deposited droplets can then directly detected by mass spectrometry. Utilizing this approach, results of analyte concentration, splitting and separation are demonstrated.

Jatkuvasatoisten mansikoiden lannoitus rajoitetussa kasvualustassa

Mansikka (Fragaria × ananassa Duch.) on tärkein Suomessa viljelty marja sekä määrällisesti että taloudellisesti. Suomessa ongelmana on lyhyt satokausi ja matala satotaso. Pääsadon aikaan runsas mansikan tarjonta markkinoilla laskee huomattavasti mansikan hintaa. Paras hinta saadaan normaalin satokauden ulkopuolella. Jatkuvasatoiset mansikkalajikkeet mahdollistaisivat pidemmän ja tasaisen satokauden, mikä vakauttaisi mansikan hintaa. Jatkuvasatoinen mansikka sopii viljelyyn kausihuoneissa korotetuilla kasvualustoilla, jolloin lannoitus ja kastelu hoidetaan tippukastelulla. Jatkuvasatoinen mansikka tuottaa kukkia ja marjoja koko satokauden, mikä vaikuttaa sen ravinnetarpeeseen. Tehdyssä tutkimuksessa testattiin kolmea eri lannoitustasoa 1,5 mS/cm, 2,3mS/cm ja 3,0 mS/cm, joiden N:K –suhde marjojen kypsymisvaiheessa oli 1:1,5. Neljäs käsittely oli kastelu johtokyvyllä 2,3 mS/cm N:K –suhteen ollessa 1:2 marjojen kypsyessä. Tutkimuksessa havainnointiin taimien vegetatiivista kasvua sekä sadon muodostusta ja marjojen laatua. Samalla seurattiin ylivaluntaveden määrää sekä veden mukana huuhtoutunutta fosforia ja typpeä. Tutkimuksessa käytetyt lajikkeet olivat ’Malling Opal’ ja ’Rondo’. Tämän tutkimuksen tulokset tukevat aikaisempia tutkimuksia, että mansikan ravinnetarve on suhteellisen matala. Voimakkain vegetatiivinen kasvu, suurin sato ja suurimmat marjat saatiin alimmalla testatulla johtokyvyllä (1,5 mS/cm). Lannoitustasolla oli hyvin vähän vaikutusta marjan laatuun tai sadon ajoittumiseen. Myöskään N:K – suhteen muutoksella ei ollut vaikutusta marjan laatuun. Taimien veden otto oli suurinta alimmalla lannoitustasolla, ja mahdollisesti kasteluveden korkea ionipitoisuus vaikeutti kasvin veden ottoa korkeilla veden johtokyvyillä. Valumaveden mukana poistuneet typpi- ja fosforipäästöt kasvoivat huomattavasti kasteluveden johtokyvyn noustessa.

Micropillar Array Based Microchips for Electrospray Ionization Mass Spectrometry, Microreactors, and Liquid Chromatographic Separation

This dissertation deals with the design, fabrication, and applications of microscale electrospray ionization chips for mass spectrometry. The microchip consists of microchannel, which leads to a sharp electrospray tip. Microchannel contain micropillars that facilitate a powerful capillary action in the channels. The capillary action delivers the liquid sample to the electrospray tip, which sprays the liquid sample to gas phase ions that can be analyzed with mass spectrometry. The microchip uses a high voltage, which can be utilized as a valve between the microchip and mass spectrometry. The microchips can be used in various applications, such as for analyses of drugs, proteins, peptides, or metabolites. The microchip works without pumps for liquid transfer, is usable for rapid analyses, and is sensitive. The characteristics of performance of the single microchips are studied and a rotating multitip version of the microchips are designed and fabricated. It is possible to use the microchip also as a microreactor and reaction products can be detected online with mass spectrometry. This property can be utilized for protein identification for example. Proteins can be digested enzymatically on-chip and reaction products, which are in this case peptides, can be detected with mass spectrometry. Because reactions occur faster in a microscale due to shorter diffusion lengths, the amount of protein can be very low, which is a benefit of the method. The microchip is well suited to surface activated reactions because of a high surface-to-volume ratio due to a dense micropillar array. For example, titanium dioxide nanolayer on the micropillar array combined with UV radiation produces photocatalytic reactions which can be used for mimicking drug metabolism biotransformation reactions. Rapid mimicking with the microchip eases the detection of possibly toxic compounds in preclinical research and therefore could speed up the research of new drugs. A micropillar array chip can also be utilized in the fabrication of liquid chromatographic columns. Precisely ordered micropillar arrays offer a very homogenous column, where separation of compounds has been demonstrated by using both laser induced fluorescence and mass spectrometry. Because of small dimensions on the microchip, the integrated microchip based liquid chromatography electrospray microchip is especially well suited to low sample concentrations. Overall, this work demonstrates that the designed and fabricated silicon/glass three dimensionally sharp electrospray tip is unique and facilitates stable ion spray for mass spectrometry.

Management of bushland vegetation using rainwater harvesting in eastern Kenya.

Microcatchment water harvesting (MCWH) improved the survival and growth of planted trees on heavy soils in eastern Kenya five to six years after planting. In the best method, the cross-tied furrow microcatchments, the mean annual increments (MAI; based on the average biomass of living trees multiplied by tree density and survival) of the total and usable biomass in Prosopis juliflora were 2787 and 1610 kg ha-1 a-1 respectively, when the initial tree density was 500 to 1667 trees per hectare. Based on survival, the indigenous Acacia horrida, A. mellifera and A. zanzibarica were the most suitable species for planting using MCWH. When both survival and yield were considered, a local seed source of the introduced P. juliflora was superior to all other species. The MAI in MCWH was at best distinctly higher than that in the natural vegetation (163­307 and 66­111 kg ha-1 a-1 for total and usable biomass respectively); this cannot satisfy the fuelwood demand of concentrated populations, such as towns or irrigation schemes. The density of seeds of woody species in the topsoil was 40.1 seeds m-2 in the Acacia-Commiphora bushland and 12.6 seeds m-2 in the zone between the bushland and the Tana riverine forest. Rehabilitation of woody vegetation using the soil seed bank alone proved difficult due to the lack of seeds of desirable species. The regeneration and dynamics of woody vegetation were also studied both in cleared and undisturbed bushland. A sub-type of Acacia-Commiphora bushland was identified as Acacia reficiens bushland, in which the dominant Commiphora species is C. campestris. Most of the woody species did not have even-aged populations but cohort structures that were skewed towards young individuals. The woody vegetation and the status of soil nutrients were estimated to recover in 15­20 years on Vertic Natrargid soils after total removal of above-ground vegetation.

Teollisuusjätevesien sadetustyöryhmän loppuraportti

Spray irrigation of industrial waste water.

Kasteluun vaikuttavista hydrometeorologisista tekijöistä

Summary: On the hydrometeorological factors affecting irrigation

Real-time multipurpose reservoir operation: a case study / Exploitation en temps reacuteel d'un reservoir agrave buts multiples: eacutetude d'un cas

A real-time operational methodology has been developed for multipurpose reservoir operation for irrigation and hydropower generation with application to the Bhadra reservoir system in the state of Karnataka, India. The methodology consists of three phases of computer modelling. In the first phase, the optimal release policy for a given initial storage and inflow is determined using a stochastic dynamic programming (SDP) model. Streamflow forecasting using an adaptive AutoRegressive Integrated Moving Average (ARIMA) model constitutes the second phase. A real-time simulation model is developed in the third phase using the forecast inflows of phase 2 and the operating policy of phase 1. A comparison of the optimal monthly real-time operation with the historical operation demonstrates the relevance, applicability and the relative advantage of the proposed methodology.

Improved Inverted V-Notch or Chimney Weir

This paper is devoted to the improvement of the measuring range of inverted V-notch (IVN) weir, a practical linear sharp-crested weir, designed earlier by the writers. The range of linearity of IVN can be considerably enhanced (by more than 200%) by the addition of a retangular weir of width 0.265W (W = half crest width) at a depth of 0.735d (d = altitude of IVN), above the crest of the weir, which is equivalent to providing at this depth two vertical straight lines to the IVN, resulting in a chimney-shaped profile; hence, the modified weir is named chimney weir. The design parameters of the weir, that is, the linearity range, base flow depth, and datum constant, which fixes the reference plane of the weir, are estimated by solving the nonlinear programming problem using a numerical optimization procedure. For flows through this weir above a depth of 0.22d, the discharges are proportional to the depth of flow measured above a reference plane situated at 0.08d above the weir crest for all heads in the range 0.22d <= h <= 2.43d, within a maximum percentage deviation of ±1.5 from the theoretical discharge. A significant result of the analysis is that the same linear head-discharge relationship governing the flow through the IVN is also valid for the extended chimney weir. Experiments with three different chimney weirs show excellent agreement with the theory by giving a constant average coefficient of discharge for each weir.

Phytophthora in Finnish nurseries

Human-mediated movement of plants and plant products is now generally accepted to be the primary mode of introduction of plant pathogens. Species of the genus Phytophthora are commonly spread in this way and have caused severe epidemics in silviculture, horticulture as well as natural systems all over the world. The aims of the study were to gather information on the occurrence of Phytophthora spp. in Finnish nurseries, to produce information for risk assessments for these Phytophthora spp. by determining their host ranges and tolerance of cold temperatures, and to establish molecular means for their detection. Phytophthora cactorum was found to persist in natural waterbodies and results suggest that irrigation water might be a source of inoculum in nurseries. In addition to P. cactorum, isolates from ornamental nursery Rhododendron yielded three species new to Finland: P. ramorum, P. plurivora and P. pini. The only species with quarantine status, P. ramorum, was most adapted to growth in cold temperatures and able to persist in the nursery in spite of an annual sanitation protocol. Phytophthora plurivora and the closely related P. pini had more hosts among Nordic tree and plant species than P. ramorum and P. cactorum, and also had higher infectivity rates. All four species survived two weeks in -5 °C , and thus soil survival of these Phytophthoras in Finland is likely under current climatic conditions. The most common tree species in Finnish nurseries, Picea abies, was highly susceptible to P. plurivora and P. pini in pathogenicity trials. In a histological examination of P. plurivora in P. abies shoot tissues, fast necrotrophic growth was observed in nearly all tissues. The production of propagules in P. abies shoot tissue was only weakly indicated. In this study, a PCR DGGE technique was developed for simultaneous detection and identification of Phytophthora spp. It reliably detected Phytophthora in plant tissues and could discriminate most test species as well as indicate instances of multiple-species infections. It proved to be a useful detection and identification tool either applied alone or in concert with traditional isolation culture techniques. All of the introduced species of Phytophthora had properties that promote a high risk of establishment and spread in Finland. It is probable that more pathogens of this genus will be introduced and become established in Finland and other Nordic countries unless efficient phytosanitary control becomes standard practice in the international plant trade.

Chronic suppression of testicular function by constant infusion of gonadotropin-releasing hormone agonist and testosterone supplementation in the bonnet monkey (Macaca radiata)

Objective: To study the efficacy of long-term buserelin acetate infusion to desensitize pituitary and block testicular function in adult male monkeys (Macaca radiata). Animals: Proven fertile male monkeys exhibiting normal testicular function. Protocol: Each of the control (n = 5) and experimental monkeys (n = 10) received a fresh miniosmotic pump every 21 days, whereas pumps in controls delivered vehicle of experimentals released 50-mu-g buserelin acetate every 24 hours. On day 170 (renewed every 60 days) a silastic capsule containing crystalline testosterone (T) was implanted in the experimental monkeys. At the end of 3 years, treatment was stopped, and recovery of testicular function and fertility monitored. Results: (1) Treatment resulted in marked reduction of nocturnal but not basal serum T; (2) the pituitary remained desensitized to buserelin acetate throughout the 3-year period; (3) animals were largely azoospermic with occasional oligospermia exhibited by two monkeys; and (4) withdrawal of treatment restored testicular function, with 70% of animals regaining fertility. Conclusion: Long-term infertility (but restorable) can be induced in male monkeys by constant infusion of buserelin acetate and T.