Dynamic modeling for construction innovation

Previous research on construction innovation has commonly recognized the importance of the organizational climate and key individuals, often called “champions,” for the success of innovation. However, it rarely focuses on the role of participants at the project level and addresses the dynamics of construction innovation. This paper therefore presents a dynamic innovation model that has been developed using the concept of system dynamics. The model incorporates the influence of several individual and situational factors and highlights two critical elements that drive construction innovations: (1) normative pressure created by project managers through their championing behavior, and (2) instrumental motivation of team members facilitated by a supportive organizational climate. The model is qualified empirically, using the results of a survey of project managers and their project team members working for general contractors in Singapore, by assessing casual relationships for key model variables. Finally, the paper discusses the implications of the model structure for fostering construction innovations.

Sources of ultrafine particles and chemical species along a traffic corridor : comparison of the results from two receptor models

Particulate matter is common in our environment and has been linked to human health problems particularly in the ultrafine size range. A range of chemical species have been associated with particulate matter and of special concern are the hazardous chemicals that can accentuate health problems. If the sources of such particles can be identified then strategies can be developed for the reduction of air pollution and consequently, the improvement of the quality of life. In this investigation, particle number size distribution data and the concentrations of chemical species were obtained at two sites in Brisbane, Australia. Source apportionment was used to determine the sources (or factors) responsible for the particle size distribution data. The apportionment was performed by Positive Matrix Factorisation (PMF) and Principal Component Analysis/Absolute Principal Component Scores (PCA/APCS), and the results were compared with information from the gaseous chemical composition analysis. Although PCA/APCS resolved more sources, the results of the PMF analysis appear to be more reliable. Six common sources identified by both methods include: traffic 1, traffic 2, local traffic, biomass burning, and two unassigned factors. Thus motor vehicle related activities had the most impact on the data with the average contribution from nearly all sources to the measured concentrations higher during peak traffic hours and weekdays. Further analyses incorporated the meteorological measurements into the PMF results to determine the direction of the sources relative to the measurement sites, and this indicated that traffic on the nearby road and intersection was responsible for most of the factors. The described methodology which utilised a combination of three types of data related to particulate matter to determine the sources could assist future development of particle emission control and reduction strategies.

Investigation of the airborne submicrometer particles emitted by dredging vessels using a plume capture method

This paper presents a method for investigating ship emissions, the plume capture and analysis system (PCAS), and its application in measuring airborne pollutant emission factors (EFs) and particle size distributions. The current investigation was conducted in situ, aboard two dredgers (Amity: a cutter suction dredger and Brisbane: a hopper suction dredger) but the PCAS is also capable of performing such measurements remotely at a distant point within the plume. EFs were measured relative to the fuel consumption using the fuel combustion derived plume CO2. All plume measurements were corrected by subtracting background concentrations sampled regularly from upwind of the stacks. Each measurement typically took 6 minutes to complete and during one day, 40 to 50 measurements were possible. The relationship between the EFs and plume sample dilution was examined to determine the plume dilution range over which the technique could deliver consistent results when measuring EFs for particle number (PN), NOx, SO2, and PM2.5 within a targeted dilution factor range of 50-1000 suitable for remote sampling. The EFs for NOx, SO2, and PM2.5 were found to be independent of dilution, for dilution factors within that range. The EF measurement for PN was corrected for coagulation losses by applying a time dependant particle loss correction to the particle number concentration data. For the Amity, the EF ranges were PN: 2.2 - 9.6 × 1015 (kg-fuel)-1; NOx: 35-72 g(NO2).(kg-fuel)-1, SO2 0.6 - 1.1 g(SO2).(kg-fuel)-1and PM2.5: 0.7 – 6.1 g(PM2.5).(kg-fuel)-1. For the Brisbane they were PN: 1.0 – 1.5 x 1016 (kg-fuel)-1, NOx: 3.4 – 8.0 g(NO2).(kg-fuel)-1, SO2: 1.3 – 1.7 g(SO2).(kg-fuel)-1 and PM2.5: 1.2 – 5.6 g(PM2.5).(kg-fuel)-1. The results are discussed in terms of the operating conditions of the vessels’ engines. Particle number emission factors as a function of size as well as the count median diameter (CMD), and geometric standard deviation of the size distributions are provided. The size distributions were found to be consistently uni-modal in the range below 500 nm, and this mode was within the accumulation mode range for both vessels. The representative CMDs for the various activities performed by the dredgers ranged from 94-131 nm in the case of the Amity, and 58-80 nm for the Brisbane. A strong inverse relationship between CMD and EF(PN) was observed.

The new normativity : the innovation imperative

At a quite fundamental level, the very way in which Public Service Broadcasting (PSB) may envisage its future usually captured in the semantic shift from PSB to Public Service Media (PSM) is at stake when considering the recent history of public value discourse and the public value test. The core Reithian PSB idea assumed that public value would be created through the application of core principles of universality of availability and appeal, provision for minorities, education of the public, distance from vested interests, quality programming standards, program maker independence, and fostering of national culture and the public sphere. On the other hand, the philosophical import of the public value test is that potentially any excursion into the provision of new media services needs to be justified ex ante. In this era of New Public Management, greater transparency and accountability, and the proposition that resources for public value deliverables be contestable and not sequestered in public sector institutions, what might be the new Archimedean point around which a contemporised normativity for PSM be built? This paper will argue for the innovation imperative as an organising principle for contemporary PSM. This may appear counterintuitive, as it is precisely PSB’s predilection for innovating in new media services (in online, mobile, and social media) that has produced the constraining apparatus of the ex ante/public value/Drei-Stufen-Test in Europe, based on principles of competitive neutrality and transparency in the application of public funds for defined and limited public benefit. However, I argue that a commitment to innovation can define as complementary to, rather than as competitive ‘crowding out’, the new products and services that PSM can, and should, be delivering into a post-scarcity, superabundant all-media marketplace. The evidence presented in this paper for this argument is derived mostly from analysis of PSM in the Australian media ecology. While no PSB outside Europe is subject to a formal public value test, the crowding out arguments are certainly run in Australia, particularly by powerful commercial interests for whom free news is a threat to monetising quality news journalism. Take right wing opinion leader, herself a former ABC Board member, Judith Sloan: ‘… the recent expansive nature of the ABC – all those television stations, radio stations and online offerings – is actually squeezing activity that would otherwise be undertaken by the private sector. From partly correcting market failure, the ABC is now causing it. We are now dealing with a case of unfair competition and wasted taxpayer funds’ (The Drum, 1 August http://www.abc.net.au/unleashed/2818220.html). But I argue that the crowding out argument is difficult to sustain in Australia because of the PSB’s non-dominant position and the fact that much of innovation generated by the two PSBs, the ABC and the SBS, has not been imitated by or competed for by the commercials. The paper will bring cases forward, such as SBS’ Go Back to Where you Came From (2011) as an example of product innovation, and a case study of process and organisational innovation which also has resulted in specific product and service innovation – the ABC’s Innovation Unit. In summary, at least some of the old Reithian dicta, along with spectrum scarcity and market failure arguments, have faded or are fading. Contemporary PSM need to justify their role in the system, and to society, in terms of innovation.

Assessing the overuse of antibiotics in children with URTIs in Saudi Arabia : development of the parental perception on antibiotics scale (PAPA scale)

Background: Antibiotic overuse is influenced by several factors that can only be measured using a valid and reliable psychosocial measurement instrument. This study aims to establish translation and early stage validation of an instrument recently developed by this research team to measure factors influencing the overuse of antibiotics in children with upper respiratory tract infections in Saudi Arabia. Method: The content evaluation panel was composed of area experts approached using the Delphi Technique. Experts were provided with the questionnaires iteratively, on a three-round basis until consensus on the relevance of items was reached independently. Translation was achieved by adapting Brislin’s model of translation. Results: After going through the iterative process with the experts, consensus was reached to 58 items (including demographics). Experts also pointed out some issues related to ambiguity and redundancy in some items. A final Arabic version was produced from the translation process. Conclusion: This study produced preliminary validation of the developed instrument from the experts’ contributions. Then, the instrument was translated from English to Arabic. The instrument will undergo further validation steps in the future, such as construct validity.

Assessing the overuse of antibiotics in children in Saudi Arabia : validation of the parental perception on antibiotics scale (PAPA scale)

Background Antibiotics overuse is a global public health issue influenced by several factors, of which some are parent-related psychosocial factors that can only be measured using valid and reliable psychosocial measurement instruments. The PAPA scale was developed to measure these factors and the content validity of this instrument was assessed. Aim This study further validated the recently developed instrument in terms of (1) face validity and (2) construct validity including: deciding the number and nature of factors, and item selection. Methods Questionnaires were self-administered to parents of children between the ages of 0 and 12 years old. Parents were conveniently recruited from schools’ parental meetings in the Eastern Province, Saudi Arabia. Face validity was assessed with regards to questionnaire clarity and unambiguity. Construct validity and item selection processes were conducted using Exploratory factor analysis. Results Parallel analysis and Exploratory factor analysis using principal axis factoring produced six factors in the developed instrument: knowledge and beliefs, behaviours, sources of information, adherence, awareness about antibiotics resistance, and parents’ perception regarding doctors’ prescribing behaviours. Reliability was assessed (Cronbach’s alpha = 0.78) which demonstrates the instrument as being reliable. Conclusion The ‘factors’ produced in this study coincide with the constructs contextually identified in the development phase of other instruments used to study antibiotic use. However, no other study considering perceptions of antibiotic use had gone beyond content validation of such instruments. This study is the first to constructively validate the factors underlying perceptions regarding antibiotic use in any population and in parents in particular.

Organizational culture in airworthiness management programmes : extending an existing measurement model

All civil and private aircraft are required to comply with the airworthiness standards set by their national airworthiness authority and throughout their operational life must be in a condition of safe operation. Aviation accident data shows that over 20% of all fatal accidents in aviation are due to airworthiness issues, specifically aircraft mechanical failures. Ultimately it is the responsibility of each registered operator to ensure that their aircraft remain in a condition of safe operation, and this is done through both effective management of airworthiness activities and the effective programme governance of safety outcomes. Typically, the projects within these airworthiness management programmes are focused on acquiring, modifying and maintaining the aircraft as a capability supporting the business. Programme governance provides the structure through which the goals and objectives of airworthiness programmes are set along with the means of attaining them. Whilst the principal causes of failures in many programmes can be traced to inadequate programme governance, many of the failures in large-scale projects can have their root causes in the organizational culture and more specifically in the organizational processes related to decision-making. This paper examines the primary theme of project and programme-based enterprises, and introduces a model for measuring organizational culture in airworthiness management programmes using measures drawn from 211 respondents in Australian airline programmes. The paper describes the theoretical perspectives applied to modifying an original model to specifically focus it on measuring the organizational culture of programmes for managing airworthiness; identifying the most important factors needed to explain the relationship between the measures collected, and providing a description of the nature of these factors. The paper concludes by identifying a model that best describes the organizational culture data collected from seven airworthiness management programmes.

Experimental and computer simulation validation of ultrasound phase interference created by lateral inhomogeneity of transit time in replica bone marrow composite models

Purpose: The measurement of broadband ultrasonic attenuation (BUA) in cancellous bone for the assessment of osteoporosis follows a parabolic-type dependence with bone volume fraction; having minima values corresponding to both entire bone and entire marrow. Langton has recently proposed that the primary BUA mechanism may be significant phase interference due to variations in propagation transit time through the test sample as detected over the phase-sensitive surface of the receive ultrasound transducer. This fundamentally simple concept assumes that the propagation of ultrasound through a complex solid : liquid composite sample such as cancellous bone may be considered by an array of parallel ‘sonic rays’. The transit time of each ray is defined by the proportion of bone and marrow propagated, being a minimum (tmin) solely through bone and a maximum (tmax) solely through marrow. A Transit Time Spectrum (TTS), ranging from tmin to tmax, may be defined describing the proportion of sonic rays having a particular transit time, effectively describing lateral inhomogeneity of transit time over the surface of the receive ultrasound transducer. Phase interference may result from interaction of ‘sonic rays’ of differing transit times. The aim of this study was to test the hypothesis that there is a dependence of phase interference upon the lateral inhomogenity of transit time by comparing experimental measurements and computer simulation predictions of ultrasound propagation through a range of relatively simplistic solid:liquid models exhibiting a range of lateral inhomogeneities. Methods: A range of test models was manufactured using acrylic and water as surrogates for bone and marrow respectively. The models varied in thickness in one dimension normal to the direction of propagation, hence exhibiting a range of transit time lateral inhomogeneities, ranging from minimal (single transit time) to maximal (wedge; ultimately the limiting case where each sonic ray has a unique transit time). For the experimental component of the study, two unfocused 1 MHz ¾” broadband diameter transducers were utilized in transmission mode; ultrasound signals were recorded for each of the models. The computer simulation was performed with Matlab, where the transit time and relative amplitude of each sonic ray was calculated. The transit time for each sonic ray was defined as the sum of transit times through acrylic and water components. The relative amplitude considered the reception area for each sonic ray along with absorption in the acrylic. To replicate phase-sensitive detection, all sonic rays were summed and the output signal plotted in comparison with the experimentally derived output signal. Results: From qualtitative and quantitative comparison of the experimental and computer simulation results, there is an extremely high degree of agreement of 94.2% to 99.0% between the two approaches, supporting the concept that propagation of an ultrasound wave, for the models considered, may be approximated by a parallel sonic ray model where the transit time of each ray is defined by the proportion of ‘bone’ and ‘marrow’. Conclusions: This combined experimental and computer simulation study has successfully demonstrated that lateral inhomogeneity of transit time has significant potential for phase interference to occur if a phase-sensitive ultrasound receive transducer is implemented as in most commercial ultrasound bone analysis devices.

Improving opportunity recognition and business performance in small and medium manufacturing enterprises through design innovation programs

Increasing awareness of the benefits of stimulating entrepreneurial behaviour in small and medium enterprises has fostered strong interest in innovation programs. Recently many western countries have invested in design innovation for better firm performance. This research presents some early findings from a study of companies that participated in a holistic approach to design innovation, where the outcomes include better business performance and better market positioning in global markets. Preliminary findings from in-depth semi-structured interviews indicate the importance of firm openness to new ways of working and to developing new processes of strategic entrepreneurship. Implications for theory and practice are discussed.

Composition and morphology of particle emissions from in-use aircraft during takeoff and landing

In order to provide realistic data for air pollution inventories and source apportionment at airports, the morphology and composition of ultrafine particles (UFP) in aircraft engine exhaust were measured and characterized. For this purpose, two independent measurement techniques were employed to collect emissions during normal takeoff and landing operations at Brisbane Airport, Australia. PM1 emissions in the airfield were collected on filters and analyzed using the particle-induced X-ray emission (PIXE) technique. Morphological and compositional analyses of individual ultrafine particles in aircraft plumes were performed on silicon nitride membrane grids using transmission electron microscopy (TEM) combined with energy-dispersive X-ray microanalysis (EDX). TEM results showed that the deposited particles were in the range of 5 to 100 nm in diameter, had semisolid spherical shapes and were dominant in the nucleation mode (18 – 20 nm). The EDX analysis showed the main elements in the nucleation particles were C, O, S and Cl. The PIXE analysis of the airfield samples was generally in agreement with the EDX in detecting S, Cl, K, Fe and Si in the particles. The results of this study provide important scientific information on the toxicity of aircraft exhaust and their impact on local air quality.

Spatial variation of particle number concentration in school microscale environments and its impact on exposure assessment

It has not yet been established whether the spatial variation of particle number concentration (PNC) within a microscale environment can have an effect on exposure estimation results. In general, the degree of spatial variation within microscale environments remains unclear, since previous studies have only focused on spatial variation within macroscale environments. The aims of this study were to determine the spatial variation of PNC within microscale school environments, in order to assess the importance of the number of monitoring sites on exposure estimation. Furthermore, this paper aims to identify which parameters have the largest influence on spatial variation, as well as the relationship between those parameters and spatial variation. Air quality measurements were conducted for two consecutive weeks at each of the 25 schools across Brisbane, Australia. PNC was measured at three sites within the grounds of each school, along with the measurement of meteorological and several other air quality parameters. Traffic density was recorded for the busiest road adjacent to the school. Spatial variation at each school was quantified using coefficient of variation (CV). The portion of CV associated with instrument uncertainty was found to be 0.3 and therefore, CV was corrected so that only non-instrument uncertainty was analysed in the data. The median corrected CV (CVc) ranged from 0 to 0.35 across the schools, with 12 schools found to exhibit spatial variation. The study determined the number of required monitoring sites at schools with spatial variability and tested the deviation in exposure estimation arising from using only a single site. Nine schools required two measurement sites and three schools required three sites. Overall, the deviation in exposure estimation from using only one monitoring site was as much as one order of magnitude. The study also tested the association of spatial variation with wind speed/direction and traffic density, using partial correlation coefficients to identify sources of variation and non-parametric function estimation to quantify the level of variability. Traffic density and road to school wind direction were found to have a positive effect on CVc, and therefore, also on spatial variation. Wind speed was found to have a decreasing effect on spatial variation when it exceeded a threshold of 1.5 (m/s), while it had no effect below this threshold. Traffic density had a positive effect on spatial variation and its effect increased until it reached a density of 70 vehicles per five minutes, at which point its effect plateaued and did not increase further as a result of increasing traffic density.

Business planning, innovation and performance in nascent firms

Debate about the relationships between business planning and performance has been active for decades (Bhidé, 2000; Mintzberg, 1994). While results have been inconclusive, this topic still strongly divides the research community (Brinckmann et al., 2010; Chwolka & Raith, 2011; Delmar & Shane, 2004; Frese, 2009; Gruber, 2007; Honig & Karlsson, 2004). Previous research explored the relationships between innovation and the venture creation process (Amason et al., 2006, Dewar & Dutton, 1986; Jennings et al., 2009). However, the relationships between business planning and innovation have mostly been invoked indirectly in the strategy and entrepreneurship literatures through the notion of uncertainty surrounding the development of innovation. Some posited that planning may be irrelevant due to the iterative process, the numerous changes innovation development entails and the need to be flexible (Brews & Hunt, 1999). Others suggested that planning may facilitate the achievement of goals and overcoming of obstacles (Locke and Latham, 2000), guide the venture in its allocation of resources (Delmar and Shane, 2003) and help to foster the communication about the innovation being developed (Liao & Welsh, 2008). However, the nature and extents of the relationships between business planning, innovation and performance are still largely unknown. Moreover, if the reasons why ventures should engage (Frese, 2009) –or not- (Honig, 2004) in business planning have been investigated quite extensively (Brinckmann et al., 2010), the specific value of business planning for nascent firms developing innovation is still unclear. The objective of this paper is to shed some light on these important aspects by investigating the two following questions on a large sample of random nascent firms: 1) how is business planning use over time by new ventures developing different types and degrees of innovation? 2) how do business planning and innovation impact the performance of the nascent firms? Methods & Key propositions This PSED-type study draws its data from the first three waves of the CAUSEE project where 30,105 Australian households were randomly contacted by phone using a methodology to capture emerging firms (Davidsson, Steffens, Gordon, Reynolds, 2008). This screening led to the identification of 594 nascent ventures (i.e., firms that were not operating yet at the time of the identification) that were willing to participate in the study. Comprehensive phone interviews were conducted with these 594 ventures. Likewise, two comprehensive follow-ups were organised 12 months and 24 months later where 80% of the eligible cases of the previous wave completed the interview. The questionnaire contains specific sections investigating business plans such as: presence or absence, degree of formality and updates of the plan. Four types of innovation are measured along three degrees of intensity to produce a comprehensive continuous measure ranging from 0 to 12 (Dahlqvist & Wiklund, 2011). Other sections informing on the gestation activities, industry and different types of experiences will be used as controls to measure the relationships and the impacts of business planning and innovation on the performance of nascent firms overtime. Results from two rounds of pre-testing informed the design of the instrument included in the main survey. The three waves of data are used to first test and compare the use of planning amongst nascent firms by their degrees of innovation and then to examine their impact on performance overtime through regression analyses. Results and Implications Three waves of data collection have been completed. Preliminary results show that on average, innovative firms are more likely to have a business plans than their low innovative counterpart. They are also most likely to update their plan suggesting a more continuous use of the plan over time than previously thought. Further analyses regarding the relationships between business planning, innovation and performance are undergoing. This paper is expected to contribute to the literature on business planning and innovation by measuring quantitatively their impact on nascent firms activities and performance at different stages of their development. In addition, this study will shed a new light on the business planning-performance relationship by disentangling plans, types of nascent firms regarding their innovation degres and their performance over time. Finally, we expect to increase the understanding of the venture creation process by analysing those questions on nascent firms from a large longitudinal sample of randomly selected ventures. We acknowledge the results from this study will be preliminary and will have to be interpreted with caution as the business planning-performance is not a straightforward relationship (Brinckmann et al., 2010). Meanwhile, we believe that this study is important to the field of entrepreneurship as it provides some much needed insights on the processes used by nascent firms during their creation and early operating stages.

Individual, environmental, and meteorological predictors of daily personal ultraviolet radiation exposure measurements in a United States cohort study

Background Individual exposure to ultraviolet radiation (UVR) is challenging to measure, particularly for diseases with substantial latency periods between first exposure and diagnosis of outcome, such as cancer. To guide the choice of surrogates for long-term UVR exposure in epidemiologic studies, we assessed how well stable sun-related individual characteristics and environmental/meteorological factors predicted daily personal UVR exposure measurements. Methods We evaluated 123 United States Radiologic Technologists subjects who wore personal UVR dosimeters for 8 hours daily for up to 7 days (N = 837 days). Potential predictors of personal UVR derived from a self-administered questionnaire, and public databases that provided daily estimates of ambient UVR and weather conditions. Factors potentially related to personal UVR exposure were tested individually and in a model including all significant variables. Results The strongest predictors of daily personal UVR exposure in the full model were ambient UVR, latitude, daily rainfall, and skin reaction to prolonged sunlight (R2 = 0.30). In a model containing only environmental and meteorological variables, ambient UVR, latitude, and daily rainfall were the strongest predictors of daily personal UVR exposure (R2 = 0.25). Conclusions In the absence of feasible measures of individual longitudinal sun exposure history, stable personal characteristics, ambient UVR, and weather parameters may help estimate long-term personal UVR exposure.

Destination branding performance measurement for practitioners

While academic interest in destination branding has been gathering momentum since the field commenced in the late 1990s, one important gap in this literature that has received relatively little attention to date is the measurement of destination brand performance. This paper sets out one method for assessing the performance of a destination brand over time. The intent is to present an approach that will appeal to marketing practitioners, and which is also conceptually sound. The method is underpinned by Decision Set Theory and the concept of Consumer-Based Brand Equity (CBBE), while the key variables mirror the branding objectives used by many destination marketing organisations (DMO). The approach is demonstrated in this paper to measure brand performance for Australia in the New Zealand market. It is suggested the findings provide indicators of both i) the success of previous marketing communications, and ii) future performance, which can be easily communicated to a DMO’s stakeholders.

Prostate gland and extra-capsular tissue 3D reconstruction and measurement

Currently there are little objective parameters that can quantify the success of one form of prostate surgical removal over another. Accordingly, at Old Dominion University (ODU) we have been developing a process resulting in the use of software algorithms to assess the coverage and depth of extra-capsular soft tissue removed with the prostate by the various surgical approaches. Parameters such as the percent of capsule that is bare of soft tissue and where present the depth and extent of coverage have been assessed. First, visualization methods and tools are developed for images of prostate slices that are provided to ODU by the Pathology Department at Eastern Virginia Medical School (EVMS). The visualization tools interpolate and present 3D models of the prostates. Measurement algorithms are then applied to determine statistics about extra-capsular tissue coverage. This paper addresses the modeling, visualization, and analysis of prostate gland tissue to aid in quantifying prostate surgery success. Particular attention is directed towards the accuracy of these measurements and is addressed in the analysis discussions.