High frequency of mutation G377S in Brazilian type 3 Gaucher disease patients

Gaucher disease (GD), the most prevalent lysosome storage disorder, presents an autosomal recessive mode of inheritance. It is a paradigm for therapeutic intervention in medical genetics due to the existence of effective enzyme replacement therapy. We report here the analysis of GD in 262 unrelated Brazilian patients, carried out in order to establish the frequency of the most common mutations and to provide prognostic information based on genotype-phenotype correlations. Among 247 type 1 GD patients, mutation N370S was detected in 47% of all the alleles, but N370S/N370S homozygosity was found in only 10% of the patients, a much lower frequency than expected, suggesting that most individuals presenting this genotype may not receive medical attention. Recombinant alleles were detected at a high frequency: 44% of the chromosomes bearing mutation L444P had other mutations derived from the pseudogene sequence, present in 25% of patients. Three neuronopathic type 2 patients were homozygous for L444P, all presenting additional mutations (E326K or recombinant alleles) that probably lead to the more severe phenotypes. Six children, classified as type 1 GD patients, had a L444P/L444P genotype, showing that neuronopathic symptoms may only manifest later in life. This would indicate the need for a higher treatment dose during enzyme replacement therapy. Finally, mutation G377S was present in 4 homozygous type 1 patients and also in compound heterozygosity in 5 (42%) type 3 patients. These findings indicate that G377S cannot be unambiguously classified as mild and suggest an allele-dose effect for this mutation.

A high-carbohydrate diet enhances the adverse effect of the S2 allele of APOC3 SstI polymorphism on the TG/HDL-C ratio only in young Chinese females

Both genetic background and diet have profound effects on plasma lipid profiles. We hypothesized that a high-carbohydrate (high-CHO) diet may affect the ratios of serum lipids and apolipoproteins (apo) differently in subjects with different genotypes of the SstI polymorphism in the apoCIII gene (APOC3). Fifty-six healthy university students (27 males and 29 females, 22.89 ± 1.80 years) were given a washout diet of 54% carbohydrate for 7 days, followed by a high-CHO diet of 70% carbohydrate for 6 days without total energy restriction. Serum triglyceride (TG), total cholesterol (TC), high-density lipoprotein cholesterol (HDL-C), low-density lipoprotein cholesterol (LDL-C), apoB100, apoAI, and the APOC3 SstI polymorphism were analyzed. The ratios of serum lipids and apoB100/apoAI were calculated. At baseline, the TG/HDL-C ratio was significantly higher in females, but not in males, with the S2 allele. The differences in the TG/HDL-C ratio between genotypes remained the same after the washout and the high-CHO diet in females. When compared with those before the high-CHO diet, the TC/HDL-C (male S2 carriers: 3.13 ± 1.00 vs 2.36 ± 0.65, P = 0.000; male subjects with the S1S1 genotype: 2.97 ± 0.74 vs 2.09 ± 0.55, P = 0.000; female S2 carriers: 2.68 ± 0.36 vs 2.24 ± 0.37, P = 0.004; female subjects with the S1S1 genotype: 2.69 ± 0.41 vs 2.09 ± 0.31, P = 0.000) and LDL-C/HDL-C (male S2 carriers: 1.44 ± 0.71 vs 1.06 ± 0.26, P = 0.012; male subjects with the S1S1 genotype: 1.35 ± 0.61 vs 1.01 ± 0.29, P = 0.005; female S2 carriers: 1.18 ± 0.33 vs 1.00 ± 0.18, P = 0.049; female subjects with the S1S1 genotype: 1.18 ± 0.35 vs 1.04 ± 0.19, P = 0.026) ratios were significantly decreased after the high-CHO diet regardless of gender and of genotype of the APOC3 SstI polymorphism. However, in female S2 carriers, the TG/HDL-C (1.38 ± 0.46 vs 1.63 ± 0.70, P = 0.039) ratio was significantly increased after the high-CHO diet. In conclusion, the high-CHO diet has favorable effects on the TC/HDL-C and LDL-C/HDL-C ratios regardless of gender and of genotype of the APOC3 SstI polymorphism. Somehow, it enhanced the adverse effect of the S2 allele on the TG/HDL-C ratio only in females.

Comparison of methodologies for moisture determination on dried bee pollen samples

Bee pollen moisture value is one of the quality parameters for this product. Some countries such as Argentina, Brazil, Bulgaria, Poland and Switzerland have bee pollen regulations on quality parameters, but these are not clear regarding which method should be used for moisture determination. The aim of this paper was to compare six methods of moisture determination in dried bee pollen samples. The methods were: conventional oven at 100 °C, vacuum oven at 70 °C, desiccator with sulfuric acid, drying out process with infrared light at 85 °C, lyophilization and Karl Fisher's method. Based on the results, the best methods for moisture determination of bee pollen were the drying process with infrared and the lyophilization, since these have shown lower moisture values.

Antioxidants in yacon products and effect of long term storage

Yacon (Smallanthus sonchifolius (Poepp. and Endl.) H. Robinson) is a storage root originally grown in the Andean highlands. The fresh roots are perishable and quickly turn brown during handling and processing. Aiming to prolong shelf-life and to preserve the antioxidant compounds in yacon roots, 3 mm thick yacon slices were dried in a drying cabinet at 40, 50, and 60 ºC to a moisture content of 10-14%, and yacon strips were sun dried to a moisture content of 15-20%. The total phenolic content was measured by the Folin-Ciocalteu method, and the quenching capacity was evaluated by measuring the amount of DPPH (1,1-diphenyl-2-pidrylhydrazyl) inhibited in samples after drying and after 7 months of storage. The results showed that it is possible to preserve the antioxidant capacity in yacon after cabinet or sun drying. Both yacon chips and strips presented total phenolic content values similar to those of fresh yacon roots. Both products also showed a high inhibition capacity of DPPH (1,1-diphenyl-2-pidrylhydrazyl). A significant decrease in the phenolic content was observed in the yacon chips after storage, which indicates that the sun dried strips are more suitable for storage.

Effect of drying temperature on quality of β-glucan in white oat grains

Oats have received attention because of their nutritional characteristics, especially their high-quality content of β-glucan. The drying process reduces water content; therefore they can be preserved for long periods. However, high-temperature drying process may affect the physical, chemical, and functional properties of the grains. The objective of this study was to evaluate the effect of different drying temperatures on β-glucan quality in oat grains. Grains of oats (Avena sativa, L.), cultivar Albasul, harvested at harvest moisture content of 23% were submitted to stationary drying at air temperatures of 25, 50, 75, and 100 ºC until they reached 13% moisture content. The β-glucan content was determined in samples of oat grains and extraction was performed using water as solvent at 90 ºC. The β-glucan extract was evaluated for water holding capacity, water retention capacity, capacity of displacement, and gelation properties. Stationary of oat grains at air temperatures above 25 ºC decreased the water holding capacity, whereas the content of β-glucan and the water retention capacity of β-glucan extract was affected at temperatures above 50 ºC. Physical changes such as increased gelation capacity of the β-glucan extract occurred following drying at air temperature over 75 ºC.

Physicochemical properties of frozen tortillas from nixtamalized maize flours enriched with β-glucans

AbstractEffects of different β-glucan concentrations in maize flour on the properties of frozen maize tortillas were evaluated. Masa (dough), pre-cooked (PTs), frozen (FTs), thawed (TTs), and cooked tortillas (CTs) were made and analyzed. Moisture content of masa and tortillas significantly decreased as β-glucan concentration increased; however, the water absorption capacity (WAC), ice melting enthalpy, and frozen water in FTs increased. Texture and color of the masa, PTs, and CTs as well as sensory analysis showed differences only between tortillas with 0% and 4% β-glucans. β-glucans did not affect the texture of CTs. Soluble fiber increased by over threefold and fivefold in tortillas with 2% and 4% β-glucans, respectively, than in those without β-glucans. This result was consistent with the observed structural changes in tortillas, showing an increase in high-fiber aggregates with increasing β-glucan concentration. Tortillas with 2% β-glucans showed acceptable physicochemical, functional, and sensory properties, but over three times the soluble fiber. Therefore, it is possible to obtain frozen tortillas with high fiber content and increase their shelf life for subsequent cooking while maintaining good properties.

Characterization of biomasses from the north and northeast regions of Brazil for processes in biorefineries

Abstract In search for renewable energy sources, the Brazilian residual biomasses stand out due to their favorable physical and chemical properties, low cost, and their being less pollutant. Therefore, they are likely to be used in biorefineries in the production of chemical inputs to substitute fossil fuels. This substitution is possible due to the high contents of carbohydrates (>40%), low contents of extractives (<20%), ashes (<8%) and moisture (<8%) found in these residual biomasses. High calorific values of all residues also offer them the chance to be used in combustion. A principal components analysis (PCA) was performed for better understanding of the samples and their hysic-chemical properties. Thus, this study aimed to characterize biomasses from the north (babassu residues, such as mesocarp and endocarp; pequi and Brazil nut) and northeast (agave and coconut) regions of Brazil, in order to contribute to the preservation of the environment and strengthen the economy of the region.

Sensory acceptability and fatty acid profile of fish crackers made from Carassius gibelio

Abstract In this study, our aim was to consider the production of fish crackers using Carassius gibelio and to investigate the fatty acid profile and sensory quality of the fish crackers. Fish cracker mixture with a ratio 3.5:1.5 (minced fish/wheat starch) was obtained. Based on the total minced fish and starch level, 1.75% salt, 0.25% black pepper, 2% sunflower oil, 1% baking powder and 10% cold water (4 °C) were added and stirred until a homogenous mixture was obtained. The mixture was compressed in an extractor and baked. The moisture content of minced fish (CMF), cracker dough (CD) and crackers (CCr) was 77.73 ± 0.14%, 63.10 ± 2.18% and 7.95 ± 0.67% respectively. The n6/n3 ratio of crackers was 2.61 ± 0.20, PUFA/SFA ratio 2.28 ± 0.06 and DHA/EPA ratio 1.81 ± 0.01. The overall acceptability score obtained by the sensory evaluation of panelists was very high (8.09 ± 0.25).

Seed moisture range in a soybean plant

It is common to see in any soybean plant that seeds reach maturity at different times. Thus the objective of the present study was to determine the magnitude of the seed moisture range at different stages of maturation in a soybean plant. The field study was conducted in a tropical region in the state of Mato Grosso - Brazil, established with foundation seeds of the MTBR-45 cultivar, and at flowering, 100 plants were marked at the same maturity stage. Harvesting began when seeds still were at high moisture content (MC). At each of eight harvesting times, during 16 days, all pods from two plants were harvested and the seeds from each pod were hand threshed individually and determined the moisture content . The results revealed that there is a great distribution of seed MC in a soybean plant, where at physiological maturity, the magnitude can reach more than 30 percentage points. Also, even with an average MC below 12%, there were more than 20 % of the seeds with MC above 13% and some seeds at this point had been waiting to be harvested for more than a week. The following conclusions and/or recommendations can be taken: 1- The great seed MC range in a soybean seed lot harvested at field maturity leads to the presence of seeds susceptible to mechanical damage and with MC unsafe for adequate storage; 2 - It is recommended that harvesting be accomplished when the seeds are in the 15-18% MC range, in order to minimize field deterioration and the percentage of seeds with high MC; 3- Drying is recommended, even when soybean seeds are in their average MC safe for storage.

Drying peanut seed using air ambient temperature at low relative humidity

The moisture content of peanut kernel (Arachis hypogaea L.) at digging ranges from 30 to 50% on a wet basis (w.b.). The seed moisture content must be reduced to 10.5% or below before seeds can be graded and marketed. After digging, peanuts are cured on a window sill for two to five days then mechanically separated from the vine. Heated air is used to further dry the peanuts from approximately 18 to 10% moisture content w.b. Drying is required to maintain peanut seed and grain quality. Traditional dryers pass a high temperature and high humidity air stream through the seed mass. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the kernels. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is heated and passed through the seed. A study was conducted to evaluate the performance of the HPT system in drying peanut seed. The seeds inside the shells were dried from 17.4 to 7.3% in 14 hours and 11 minutes, with a rate of moisture removal of 0.71% mc per hour. This drying process caused no reduction in seed quality as measured by the standard germination, accelerated ageing and field emergence tests. It was concluded that the HPT system is a promising technology for drying peanut seed when efficiency and maintenance of physiological quality are desired.

Real-time monitoring of laser scribing process utilizing high-speed camera

Currently, laser scribing is growing material processing method in the industry. Benefits of laser scribing technology are studied for example for improving an efficiency of solar cells. Due high-quality requirement of the fast scribing process, it is important to monitor the process in real time for detecting possible defects during the process. However, there is a lack of studies of laser scribing real time monitoring. Commonly used monitoring methods developed for other laser processes such a laser welding, are sufficient slow and existed applications cannot be implemented in fast laser scribing monitoring. The aim of this thesis is to find a method for laser scribing monitoring with a high-speed camera and evaluate reliability and performance of the developed monitoring system with experiments. The laser used in experiments is an IPG ytterbium pulsed fiber laser with 20 W maximum average power and Scan head optics used in the laser is Scanlab’s Hurryscan 14 II with an f100 tele-centric lens. The camera was connected to laser scanner using camera adapter to follow the laser process. A powerful fully programmable industrial computer was chosen for executing image processing and analysis. Algorithms for defect analysis, which are based on particle analysis, were developed using LabVIEW system design software. The performance of the algorithms was analyzed by analyzing a non-moving image from the scribing line with resolution 960x20 pixel. As a result, the maximum analysis speed was 560 frames per second. Reliability of the algorithm was evaluated by imaging scribing path with a variable number of defects 2000 mm/s when the laser was turned off and image analysis speed was 430 frames per second. The experiment was successful and as a result, the algorithms detected all defects from the scribing path. The final monitoring experiment was performed during a laser process. However, it was challenging to get active laser illumination work with the laser scanner due physical dimensions of the laser lens and the scanner. For reliable error detection, the illumination system is needed to be replaced.

Characterization of Carotid Plaques with Ultrasound Non-Invasive Vascular Elastography (NIVE) : Feasibility and Correlation with High-Resolution Magnetic Resonance Imaging

L’accident vasculaire cérébral (AVC) est une cause principale de décès et de morbidité dans le monde; une bonne partie des AVC est causée par la plaque d’athérosclérose carotidienne. La prévention de l’AVC chez les patients ayant une plaque carotidienne demeure controversée, vu les risques et bénéfices ambigus associés au traitement chirurgical ou médical. Plusieurs méthodes d’imagerie ont été développées afin d’étudier la plaque vulnérable (dont le risque est élevé), mais aucune n’est suffisamment validée ou accessible pour permettre une utilisation comme outil de dépistage. L’élastographie non-invasive vasculaire (NIVE) est une technique nouvelle qui cartographie les déformations (élasticité) de la plaque afin de détecter les plaque vulnérables; cette technique n’est pas encore validée cliniquement. Le but de ce projet est d’évaluer la capacité de NIVE de caractériser la composition de la plaque et sa vulnérabilité in vivo chez des patients ayant des plaques sévères carotidiennes, en utilisant comme étalon de référence, l’imagerie par résonance magnétique (IRM) à haute-résolution. Afin de poursuivre cette étude, une connaissance accrue de l’AVC, l’athérosclérose, la plaque vulnérable, ainsi que des techniques actuelles d’imagerie de la plaque carotidienne, est requise. Trente-et-un sujets ont été examinés par NIVE par ultrasonographie et IRM à haute-résolution. Sur 31 plaques, 9 étaient symptomatiques, 17 contenaient des lipides, et 7 étaient vulnérables selon l’IRM. Les déformations étaient significativement plus petites chez les plaques contenant des lipides, avec une sensibilité élevée et une spécificité modérée. Une association quadratique entre la déformation et la quantité de lipide a été trouvée. Les déformations ne pouvaient pas distinguer les plaques vulnérables ou symptomatiques. En conclusion, NIVE par ultrasonographie est faisable chez des patients ayant des sténoses carotidiennes significatives et peut détecter la présence d’un coeur lipidique. Des études supplémentaires de progression de la plaque avec NIVE sont requises afin d’identifier les plaques vulnérables.

Effect of Pyridoxine Deficiency in Young-Rats on High-Affinity Serotonin and Dopamine Receptors

The high-affinity bindings of [3H]-5-hydroxytryptamine to serotonin S-1 receptors, [3H]-ketanserin to serotonin S-2 receptors in the cerebral cortex, [3H]- fluphenazine to dopamine D-1 receptors, and [3H]-spiroperidol to dopamine D-2 receptors in the corpus striatum were studied in pyridoxine-deficient rats and compared to pyridoxine-supplemented controls. There was a significant increase in the maximal binding (Bmax) of serotonin S-1 and S-2 receptors with a significant decrease in their binding affinities (Kd). However, there were no significant changes either in the maximal binding or binding affinity of striatal dopamine D- 1 and D-2 receptors. Receptor sensitivity seems to correlate negatively with the corresponding neurotransmitter concentrations in the pyridoxine-deficient rats.

Investigations on The Finite Size Effects of Some Inverse Spinels and Studies on Their Composites Based on Nitrile Rubber

Magnetism and magnetic materials have been an ever-attractive subject area for engineers and scientists alike because of its versatility in finding applications in useful devices. They find applications in a host of devices ranging from rudimentary devices like loud speakers to sophisticated gadgets like waveguides and Magnetic Random Access Memories (MRAM).The one and only material in the realm of magnetism that has been at the centre stage of applications is ferrites and in that spinel ferrites received the lions share as far as practical applications are concerned.It has been the endeavour of scientists and engineers to remove obsolescence and improve upon the existing so as to save energy and integrate in to various other systems. This has been the hallmark of material scientists and this has led to new materials and new technologies.In the field of ferrites too there has been considerable interest to devise new materials based on iron oxides and other compounds. This means synthesising ultra fine particles and tuning its properties to device new materials. There are various preparation techniques ranging from top- down to bottom-up approaches. This includes synthesising at molecular level, self assembling,gas based condensation. Iow temperature eo-precipitation, solgel process and high energy ball milling. Among these methods sol-gel process allows good control of the properties of ceramic materials. The advantage of this method includes processing at low temperature. mixing at the molecular level and fabrication of novel materials for various devices.Composites are materials. which combine the good qualities of one or more components. They can be prepared in situ or by mechanical means by the incorporation of fine particles in appropriate matrixes. The size of the magnetic powders as well as the nature of matrix affect the processability and other physical properties of the final product. These plastic/rubber magnets can in turn be useful for various applications in different devices. In applications involving ferrites at high frequencies, it is essential that the material possesses an appropriate dielectric permittivity and suitable magnetic permeability. This can be achieved by synthesizing rubber ferrite composites (RFC's). RFCs are very useful materials for microwave absorptions. Hence the synthesis of ferrites in the nanoregirne.investigations on their size effects on the structural, magnetic, and electrical properties and the incorporation of these ferrites into polymer matrixes assume significance.In the present study, nano particles of NiFe204, Li(!5Fe2S04 and Col-e-O, are prepared by sol gel method. By appropriate heat treatments, particles of different grain sizes are obtained. The structural, magnetic and electrical measurements are evaluated as a function of grain size and temperature. NiFel04 prepared in the ultrafine regime are then incorporated in nitrile rubber matrix. The incorporation was carried out according to a specific recipe and for various loadings of magnetic fillers. The cure characteristics, magnetic properties, electrical properties and mechanical properties of these elastomer blends are carried out. The electrical permittivity of all the rubber samples in the X - band are also conducted.

Texture, composition and provinance of innershelf sediments between Narakkal and Purakkad, Kerala with special reference to the formation of Mud Banks

The continental shelf of southwest coast of India (Kerala) is broader and . flatter compared to that of the east coast. The unique characteristic feature of the study area (innershelf between Narakkal and Purakkad) is the intermittent appearance of 'mud banks' at certain locations during southwest monsoon. The strong seasonality manifests significant changes in the wind, waves, currents, rainfall, drainage etc., along this area. Peculiar geomorphological variation with high, mid and lowlands in the narrow strip of the hinterland, the geological formations mainly consisting of rocks of metamorphic origin and the humid tropical weathering conditions play significant role in regulating the shelf sedimentation. A complementary pattern of distri bution is observed for clay that shows an abundance in the nearshore. Silt, to a major extent, depicts semblance with clay distribution . Summation of the total asymmetry of grain size distribution are inferred from the variation of skewness and kurtosis.Factor I implies a low energy regime where the transportation and deposition phases are controlled mostly by pelagic suspension process as the factor loadings are dominant on finer phi sizes. The second Factor is inferred to be the result of a high energy regime which gives higher loadings on coarser size fractions. The third Factor which might be a transition phase (medium energy regime) representing the resultant flux of coastal circulation of the re-suspension/deposition and an onshoreoffshore advection by reworking and co-deposition of relict and modern sediments. The spatial variations of the energy regime based on the three end-member factor model exhibits high energy zone in the seaward portion transcending to a low energy one towards the coast.From the combined analysis of granulometry and SEM studies, it is concluded that the sandy patches beyond 20 m depth are of relict nature. They are the resultant responses of beach activity during the lower stand of sea level in the Holocene. Re-crystallisation features on the quartz grains indicate that they were exposed to subaerial weathering process subsequent to thei r deposition