Projeto mecânico de um modelo para túnel de vento e validação de seus componentes à partir de simulações em software de elementos finitos

The objective of this study was to develop a model that allows testing in the wind tunnel at high angles of attack and validates its most critical components by analyzing the results of simulations in finite element software. During the project this structure suffered major loads identified during the flight conditions and, from these, we calculated the stresses in critical regions defined as the parts of the model that have higher failure probabilities. All aspects associated with Load methods, mesh refining and stress analysis were taken into account in this approach. The selection of the analysis software was based on project needs, seeking greater ease of modeling and simulation. We opted for the software ANSYS® since the entire project is being developed in CAD platforms enabling a friendly integration between software's modeling and analysis

Projeto estrutural e parametrização de uma comporta deslizante utilizando o software inventor

Pós-graduação em Engenharia Mecânica - FEG

Implementação de aparato experimental para medição de instabilidades tipo Roll Waves em fluidos não- newtonianos

Pós-graduação em Engenharia Mecânica - FEIS

Aplicação de engenharia tecidual na elevação de seio maxilar: uma revisão sistemática da literatura

The purpose of this literature review is to present the state-of-the-art on the application of tissue engineering techniques in sinus lifts procedures, reporting the influence of these techniques in increasing bone height and volume in the maxillary sinus, and the osseointegration of the implants installed in the grafted areas. PubMed and Scopus databases were searched using the keywords “scaffold” OR “engineered tissue” AND “sinus augmention” OR “sinus floor elevation”. In the initial search 463 articles were selected, of which 19 were selected abstracts reading, with nine papers selected by the end, for evaluation of the application of tissue engineering techniques in sinus lift procedures. Despite the positive results of tissue engineering procedures in sinus floor elevation reported in the selected articles, further studies are still needed, for a better standardization of experimental models and materials used, leading to definitive conclusions about the effects of the application of tissue engineering procedures on bone formation in maxillary sinus lifting procedures.

Scientific use of the finite element method in Orthodontics

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Manipulação de eletrólitos na dieta de poedeiras em fase de declínio de postura em condições de altas temperaturas

Pós-graduação em Ciência e Tecnologia Animal - FEIS

Identificação de funções de transferência de ordem fracionária utilizando como entrada um degrau

Pós-graduação em Engenharia Elétrica - FEIS

Simulação em tempo real de sistemas de distribuição de energia elétrica utilizando-se estruturas com descrição de hardware em software

Pós-graduação em Engenharia Elétrica - FEIS

L3-arpsec - módulo seguro para controle e proteção do protocolo de resolução de endereços em redes definidas por software

Pós-graduação em Engenharia Elétrica - FEIS

Metodologia de simulação numérica do comportamento térmico em equipamentos eletroeletrônicos

Pós-graduação em Engenharia Elétrica - FEIS

Otimização dos parâmetros para obtenção de nanotubos em Ti-Cp por anodização eletroquímica e aplicação na liga experimental Ti-35Nb-7Zr

Pós-graduação em Engenharia Mecânica - FEG

Estudo experimental do uso de rebolos convencionais na usinagem do aço VP-50 utilizado na retificação cilíndrica, por meio de diferentes métodos de lubri-refrigeração

Pós-graduação em Engenharia Mecânica - FEB

Caracterização experimental de sistemas mecânicos com comportamento não-linear

Pós-graduação em Engenharia Mecânica - FEIS

Biocompatibility of experimental Ti-30Ta implants with compromised primary stability: effect of TEA

Purpose: Ti-Ta alloys have high potential for dental application due to a good balance between high strength and low modulus. Absence of primary anchoring may occur when dental implants are installed immediately after tooth extraction. Tranexamic acid (TEA) is used to reduce fibrin degradation and can prevent early blood clot breakdown. The aim of this study was to evaluate the biocompatibility of Ti-30Ta implants associated or not with tranexamic acid and installed with compromised primary stability. Methods and materials: Fabricated were 20 implants of titanium ASTM F67 (Grade 4) and 20 implants of Ti-30Ta alloy with dimensions of 2.1 mm × 2.8 mm Ø. They were divided (n = 10) into Group I (Ti machined), Group II (Ti machined/tranexamic acid), Group III (Ti-30Ta alloy) and Group IV (Ti-30Ta/tranexamic acid) and were implanted in tibia (defects with 2.5 mm × 3.2 mm Ø) of 40 male rats (250 g). The surgical sites were rinsed with 5% tranexamic acid solution in Groups II and IV. The animals were euthanized at 45 days postoperative. The pieces were processed in methyl methacrylate (Stevenel's blue/Alizarin red). The percentage of peri-implant tissue repair was analyzed via images obtained by an optical microscope coupled to a digital camera using Leica software and Adobe Photoshop QWin. Data were analyzed statistically with a significance level of 5%. Results: Histomorphometric results showed 97.16% of bone-implant contact for group IV, 89.78% of bone contact for group III, 70.89% for group II and 61.59% of bone contact for group I. The statistical analyses demonstrated significant differences (P < 0.05) among group I and other groups. Conclusion: The results suggest that (a) Ti-30Ta promoted an increase of bone healing and apposition around implant; (b) tranexamic acid favored the stabilization of blood clot and bone formation.

Analisys of thermal efficiency of a modified solar collector type evacuated tube

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)