Ethanol electro-oxidation in an alkaline medium using Pd/C, Au/C and PdAu/C electrocatalysts prepared by electron beam irradiation

Carbon-supported Pd, Au and bimetallic PdAu (Pd:Au 90:10, 50:50 and 30:70 atomic ratios) electrocatalysts were prepared using electron beam irradiation. The obtained materials were characterized by energy dispersive X-ray analysis (EDX), X-ray diffraction (XRD) and transmission electron microscopy (TEM), and their catalytic activities toward ethanol electro-oxidation were evaluated in an alkaline medium using electrochemical techniques, in situ attenuated total reflectance Fourier transformed infrared spectroscopy (ATR-FTIR) analysis and a single alkaline direct ethanol fuel cell (ADEFC). EDX analyses showed that the actual Pd: Au atomic ratios were very similar to the nominal ones. X-ray diffractograms of PdAu/C electrocatalysts evidenced the presence of Pd-rich (fcc) and Au-rich (fcc) phases. TEM analysis showed a homogeneous dispersion of nanoparticles on the carbon support, with an average size in the range of 3-5 nm and broad size distributions. Cyclic voltammetry (CV) and chronoamperometry (CA) experiments revealed the superior ambient activity toward ethanol electro-oxidation of PdAu/C electrocatalysts with Pd: Au ratios of 90:10 and 50:50. In situ ATR-FTIR spectroscopy measurements have shown that the mechanism for ethanol electro-oxidation is dependent on catalyst composition, leading to different reaction products, such as acetaldehyde and acetate, depending on the number of electrons transferred. Experiments on a single ADEFC were conducted between 50 and 900 C, and the best performance of 44 mW cm-2 in 2.0molL-1 ethanol was obtained at 850C for the Pd:Au 90:10 catalysts. This superior performance is most likely associated with enhancement of ethanol adsorption on Pd, oxidation of the intermediates, the presence of gold oxide-hydroxyl species, low mean particle diameters and better distribution of particles on the support. © 2013 Elsevier Ltd. All rights reserved.

Si-based thin film coating on Y-TZP: Influence of deposition parameters on adhesion of resin cement

This study evaluated the influence of deposition parameters for Si-based thin films using magnetron sputtering for coating zirconia and subsequent adhesion of resin cement. Zirconia ceramic blocks were randomly divided into 8 groups and specimens were either ground finished and polished or conditioned using air-abrasion with alumina particles coated with silica. In the remaining groups, the polished specimens were coated with Si-based film coating with argon/oxygen magnetron discharge at 8:1 or 20:1 flux. In one group, Si-based film coating was performed on air-abraded surfaces. After application of bonding agent, resin cement was bonded. Profilometry, goniometry, Energy Dispersive X-ray Spectroscopy and Rutherford Backscattering Spectroscopy analysis were performed on the conditioned zirconia surfaces. Adhesion of resin cement to zirconia was tested using shear bond test and debonded surfaces were examined using Scanning Electron Microscopy. Si-based film coating applied on air-abraded rough zirconia surfaces increased the adhesion of the resin cement (22.78 ± 5.2 MPa) compared to those of other methods (0-14.62 MPa) (p = 0.05). Mixed type of failures were more frequent in Si film coated groups on either polished or air-abraded groups. Si-based thin films increased wettability compared to the control group but did not change the roughness, considering the parameters evaluated. Deposition parameters of Si-based thin film and after application of air-abrasion influenced the initial adhesion of resin cement to zirconia. © 2013 Elsevier B.V. All rights reserved.

Caracterização do mineral zircão através do método de traços de fissão, espectroscopia micro-raman e MEV: geocronologia do grupo Bauru

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Síntese e caracterização de cátodos de perovskitas 'La IND.0,6''Sr IND.0,4''Fe IND.y''Co IND.1-y''O IND.3-'delta'', para células a combustível de eletrólito sólido (SOFC) operando em temperaturas intermediárias

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Preparação e caracterização óptica de filmes nanocristalinos de GaAs:H depositados por RF magnetron sputtering

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Estudo in vitro das alterações na superfície do titânio comercialmente puro e da liga de titânio Ti -6Al-4V submetida a diferentes tratamentos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Resistência à cárie de esmalte dental irradiado por lasers de Er:YAG e Nd:YAG, avaliada através da morfologia e proporção Ca/P

Pós-graduação em Ciências Odontológicas - FOAR

Análise morfológica de cones de guta-percha submetidos a diferentes tratamentos de desinfecção e sua influência na microinfiltração

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Espectroscopia de impedância em vidros 22Na2O·8CaO·65SiO2·5MO2 (M = Si, Ti, Ge, Zr, Sn, Ce) sem e com troca iônica Ag+ Na+

Pós-graduação em Física - IGCE

Preparação, caracterização e aplicações eletroanalíticas de silsesquioxanos e dendrímeros modificados suportados na superfície da sílica gel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Propriedades analíticas e eletroanalíticas de um silsesquioxano nanoestruturado organofuncionalizado

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeitos da dopagem nas propriedades elétricas do sistema supercondutor BSCCO com elemento terra rara

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo da cinética da reação de decomposição da fase martensítica no sistema 'CUALMNAG'

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do efeito das adições de Ag na cinética da transformação martensítica reversa na liga Cu-11%Al

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo das propriedades de eletrocatalisadores de Pt-Ru nanoparticulados preparados via microemulsão para oxidação de metanol

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)