Computational Methods for Identification of Vibrating Structures

System identification deals with the problem of building mathematical models of dynamical systems based on observed data from the system" [1]. In the context of civil engineering, the system refers to a large scale structure such as a building, bridge, or an offshore structure, and identification mostly involves the determination of modal parameters (the natural frequencies, damping ratios, and mode shapes). This paper presents some modal identification results obtained using a state-of-the-art time domain system identification method (data-driven stochastic subspace algorithms [2]) applied to the output-only data measured in a steel arch bridge. First, a three dimensional finite element model was developed for the numerical analysis of the structure using ANSYS. Modal analysis was carried out and modal parameters were extracted in the frequency range of interest, 0-10 Hz. The results obtained from the finite element modal analysis were used to determine the location of the sensors. After that, ambient vibration tests were conducted during April 23-24, 2009. The response of the structure was measured using eight accelerometers. Two stations of three sensors were formed (triaxial stations). These sensors were held stationary for reference during the test. The two remaining sensors were placed at the different measurement points along the bridge deck, in which only vertical and transversal measurements were conducted (biaxial stations). Point estimate and interval estimate have been carried out in the state space model using these ambient vibration measurements. In the case of parametric models (like state space), the dynamic behaviour of a system is described using mathematical models. Then, mathematical relationships can be established between modal parameters and estimated point parameters (thus, it is common to use experimental modal analysis as a synonym for system identification). Stable modal parameters are found using a stabilization diagram. Furthermore, this paper proposes a method for assessing the precision of estimates of the parameters of state-space models (confidence interval). This approach employs the nonparametric bootstrap procedure [3] and is applied to subspace parameter estimation algorithm. Using bootstrap results, a plot similar to a stabilization diagram is developed. These graphics differentiate system modes from spurious noise modes for a given order system. Additionally, using the modal assurance criterion, the experimental modes obtained have been compared with those evaluated from a finite element analysis. A quite good agreement between numerical and experimental results is observed.

Comparison of turbulence models for the computational fluid dynamics simulation of wind turbine wakes in the atmospheric boundary layer

An elliptic computational fluid dynamics wake model based on the actuator disk concept is used to simulate a wind turbine, approximated by a disk upon which a distribution of forces, defined as axial momentum sources, is applied on an incoming non-uniform shear flow. The rotor is supposed to be uniformly loaded with the exerted forces estimated as a function of the incident wind speed, thrust coefficient and rotor diameter. The model is assessed in terms of wind speed deficit and added turbulence intensity for different turbulence models and is validated from experimental measurements of the Sexbierum wind turbine experiment.

Quantifying Reproducibility in Computational Biology: The Case of the Tuberculosis Drugome

How easy is it to reproduce the results found in a typical computational biology paper? Either through experience or intuition the reader will already know that the answer is with difficulty or not at all. In this paper we attempt to quantify this difficulty by reproducing a previously published paper for different classes of users (ranging from users with little expertise to domain experts) and suggest ways in which the situation might be improved. Quantification is achieved by estimating the time required to reproduce each of the steps in the method described in the original paper and make them part of an explicit workflow that reproduces the original results. Reproducing the method took several months of effort, and required using new versions and new software that posed challenges to reconstructing and validating the results. The quantification leads to “reproducibility maps” that reveal that novice researchers would only be able to reproduce a few of the steps in the method, and that only expert researchers with advance knowledge of the domain would be able to reproduce the method in its entirety. The workflow itself is published as an online resource together with supporting software and data. The paper concludes with a brief discussion of the complexities of requiring reproducibility in terms of cost versus benefit, and a desiderata with our observations and guidelines for improving reproducibility. This has implications not only in reproducing the work of others from published papers, but reproducing work from one’s own laboratory.

Integración del descodificador OpenSVC en el DSP del OMAP3530

Hoy en día el uso de dispositivos portátiles multimedia es ya una realidad totalmente habitual. Además, estos dispositivos tienen una capacidad de cálculo y unos recursos gráficos y de memoria altos, tanto es así que por ejemplo en un móvil se pueden reproducir vídeos de muy alta calidad o tener capacidad para manejar entornos 3D. El precio del uso de estos recursos es un mayor consumo de batería que en ocasiones es demasiado alto y acortan en gran medida la vida de la carga útil de la batería. El Grupo de Diseño Electrónico y Microelectrónico de la Universidad Politécnica de Madrid ha abierto una línea de trabajo que busca la optimización del consumo de energía en este tipo de dispositivos, concretamente en el ámbito de la reproducción de vídeo. El enfoque para afrontar la solución del problema se basa en obtener un mayor rendimiento de la batería a costa de disminuir la experiencia multimedia del usuario. De esta manera, cuando la carga de la batería esté por debajo de un determinado umbral mientras el dispositivo esté reproduciendo un vídeo de alta calidad será el dispositivo quien se autoconfigure dinámicamente para consumir menos potencia en esta tarea, reduciendo la tasa de imágenes por segundo o la resolución del vídeo que se descodifica. Además de lo citado anteriormente se propone dividir la descodificación y la representación del vídeo en dos procesadores, uno de propósito general y otro para procesado digital de señal, con esto se consigue que tener la misma capacidad de cálculo que con un solo procesador pero a una frecuencia menor. Para materializar la propuesta se usará la tarjeta BeagleBoard basada en un procesador multinúcleo OMAP3530 de Texas Instrument que contiene dos núcleos: un ARM1 Cortex-A8 y un DSP2 de la familia C6000. Este procesador multinúcleo además permite modificar la frecuencia de reloj y la tensión de alimentación dinámicamente para conseguir reducir de este modo el consumo del terminal. Por otro lado, como reproductor de vídeos se utilizará una versión de MPlayer que integra un descodificador de vídeo escalable que permite elegir dinámicamente la resolución o las imágenes por segundo que se decodifican para posteriormente mostrarlas. Este reproductor se ejecutará en el núcleo ARM pero debido a la alta carga computacional de la descodificación de vídeos, y que el ARM no está optimizado para este tipo de procesado de datos, el reproductor debe encargar la tarea de la descodificación al DSP. El objetivo de este Proyecto Fin de Carrera consiste en que mientras el descodificador de vídeo está ejecutándose en el núcleo DSP y el Mplayer en el núcleo ARM del OMAP3530 se pueda elegir dinámicamente qué parte del vídeo se descodifica, es decir, seleccionar en tiempo real la calidad o capa del vídeo que se quiere mostrar. Haciendo esto, se podrá quitar carga computacional al núcleo ARM y asignársela al DSP el cuál puede procesarla a menor frecuencia para ahorrar batería. 1 ARM: Es una arquitectura de procesadores de propósito general basada en RISC (Reduced Instruction Set Computer). Es desarrollada por la empresa inglesa ARM holdings. 2 DSP: Procesador Digital de Señal (Digital Signal Processor). Es un sistema basado en procesador, el cual está orientado al cálculo matemático a altas velocidad. Generalmente poseen varias unidades aritmético-lógicas (ALUs) para conseguir realizar varias operaciones simultáneamente. SUMMARY. Nowadays, the use of multimedia devices is a well known reality. In addition, these devices have high graphics and calculus performance and a lot of memory as well. In instance, we can play high quality videos and 3D environments in a mobile phone. That kind of use may increase the device's power consumption and make shorter the battery duration. Electronic and Microelectronic Design Group of Technical University of Madrid has a research line which is looking for optimization of power consumption while these devices are playing videos. The solution of this trouble is based on taking more advantage of battery by decreasing multimedia user experience. On this way, when battery charge is under a threshold while device is playing a high quality video the device is going to configure itself dynamically in order to decrease its power consumption by decreasing frame per second rate, video resolution or increasing the noise in the decoded frame. It is proposed splitting decoding and representation tasks in two processors in order to have the same calculus capability with lower frecuency. The first one is specialized in digital signal processing and the other one is a general purpose processor. In order to materialize this proposal we will use a board called BeagleBoard which is based on a multicore processor called OMAP3530 from Texas Instrument. This processor includes two cores: ARM Cortex-A8 and a TMS320C64+ DSP core. Changing clock frequency and supply voltage is allowed by OMAP3530, we can decrease the power consumption on this way. On the other hand, MPlayer will be used as video player. It includes a scalable video decoder which let us changing dynamically the resolution or frames per second rate of the video in order to show it later. This player will be executed by ARM core but this is not optimized for this task, for that reason, DSP core will be used to decoding video. The target of this final career project is being able to choose which part of the video is decoded each moment while decoder is executed by DSP and Mplayer by ARM. It will be able to change in real time the video quality, resolution and frames per second that user want to show. On this way, reducing the computational charge within the processor will be possible.

Core physics and safety analysis of Generation-IV Sodium Fast Reactors using existing and newly developed computational tools

El futuro de la energía nuclear de fisión dependerá, entre otros factores, de la capacidad que las nuevas tecnologías demuestren para solventar los principales retos a largo plazo que se plantean. Los principales retos se pueden resumir en los siguientes aspectos: la capacidad de proporcionar una solución final, segura y fiable a los residuos radiactivos; así como dar solución a la limitación de recursos naturales necesarios para alimentar los reactores nucleares; y por último, una mejora robusta en la seguridad de las centrales que en definitiva evite cualquier daño potencial tanto en la población como en el medio ambiente como consecuencia de cualquier escenario imaginable o más allá de lo imaginable. Siguiendo estas motivaciones, la Generación IV de reactores nucleares surge con el compromiso de proporcionar electricidad de forma sostenible, segura, económica y evitando la proliferación de material fisible. Entre los sistemas conceptuales que se consideran para la Gen IV, los reactores rápidos destacan por su capacidad potencial de transmutar actínidos a la vez que permiten una utilización óptima de los recursos naturales. Entre los refrigerantes que se plantean, el sodio parece una de las soluciones más prometedoras. Como consecuencia, esta tesis surgió dentro del marco del proyecto europeo CP-ESFR con el principal objetivo de evaluar la física de núcleo y seguridad de los reactores rápidos refrigerados por sodio, al tiempo que se desarrollaron herramientas apropiadas para dichos análisis. Efectivamente, en una primera parte de la tesis, se abarca el estudio de la física del núcleo de un reactor rápido representativo, incluyendo el análisis detallado de la capacidad de transmutar actínidos minoritarios. Como resultado de dichos análisis, se publicó un artículo en la revista Annals of Nuclear Energy [96]. Por otra parte, a través de un análisis de un hipotético escenario nuclear español, se evalúo la disponibilidad de recursos naturales necesarios en el caso particular de España para alimentar una flota específica de reactores rápidos, siguiendo varios escenarios de demanda, y teniendo en cuenta la capacidad de reproducción de plutonio que tienen estos sistemas. Como resultado de este trabajo también surgió una publicación en otra revista científica de prestigio internacional como es Energy Conversion and Management [97]. Con objeto de realizar esos y otros análisis, se desarrollaron diversos modelos del núcleo del ESFR siguiendo varias configuraciones, y para diferentes códigos. Por otro lado, con objeto de poder realizar análisis de seguridad de reactores rápidos, son necesarias herramientas multidimensionales de alta fidelidad específicas para reactores rápidos. Dichas herramientas deben integrar fenómenos relacionados con la neutrónica y con la termo-hidráulica, entre otros, mediante una aproximación multi-física. Siguiendo este objetivo, se evalúo el código de difusión neutrónica ANDES para su aplicación a reactores rápidos. ANDES es un código de resolución nodal que se encuentra implementado dentro del sistema COBAYA3 y está basado en el método ACMFD. Por lo tanto, el método ACMFD fue sometido a una revisión en profundidad para evaluar su aptitud para la aplicación a reactores rápidos. Durante ese proceso, se identificaron determinadas limitaciones que se discutirán a lo largo de este trabajo, junto con los desarrollos que se han elaborado e implementado para la resolución de dichas dificultades. Por otra parte, se desarrolló satisfactoriamente el acomplamiento del código neutrónico ANDES con un código termo-hidráulico de subcanales llamado SUBCHANFLOW, desarrollado recientemente en el KIT. Como conclusión de esta parte, todos los desarrollos implementados son evaluados y verificados. En paralelo con esos desarrollos, se calcularon para el núcleo del ESFR las secciones eficaces en multigrupos homogeneizadas a nivel nodal, así como otros parámetros neutrónicos, mediante los códigos ERANOS, primero, y SERPENT, después. Dichos parámetros se utilizaron más adelante para realizar cálculos estacionarios con ANDES. Además, como consecuencia de la contribución de la UPM al paquete de seguridad del proyecto CP-ESFR, se calcularon mediante el código SERPENT los parámetros de cinética puntual que se necesitan introducir en los típicos códigos termo-hidráulicos de planta, para estudios de seguridad. En concreto, dichos parámetros sirvieron para el análisis del impacto que tienen los actínidos minoritarios en el comportamiento de transitorios. Concluyendo, la tesis presenta una aproximación sistemática y multidisciplinar aplicada al análisis de seguridad y comportamiento neutrónico de los reactores rápidos de sodio de la Gen-IV, usando herramientas de cálculo existentes y recién desarrolladas ad' hoc para tal aplicación. Se ha empleado una cantidad importante de tiempo en identificar limitaciones de los métodos nodales analíticos en su aplicación en multigrupos a reactores rápidos, y se proponen interesantes soluciones para abordarlas. ABSTRACT The future of nuclear reactors will depend, among other aspects, on the capability to solve the long-term challenges linked to this technology. These are the capability to provide a definite, safe and reliable solution to the nuclear wastes; the limitation of natural resources, needed to fuel the reactors; and last but not least, the improved safety, which would avoid any potential damage on the public and or environment as a consequence of any imaginable and beyond imaginable circumstance. Following these motivations, the IV Generation of nuclear reactors arises, with the aim to provide sustainable, safe, economic and proliferationresistant electricity. Among the systems considered for the Gen IV, fast reactors have a representative role thanks to their potential capacity to transmute actinides together with the optimal usage of natural resources, being the sodium fast reactors the most promising concept. As a consequence, this thesis was born in the framework of the CP-ESFR project with the generic aim of evaluating the core physics and safety of sodium fast reactors, as well as the development of the approppriated tools to perform such analyses. Indeed, in a first part of this thesis work, the main core physics of the representative sodium fast reactor are assessed, including a detailed analysis of the capability to transmute minor actinides. A part of the results obtained have been published in Annals of Nuclear Energy [96]. Moreover, by means of the analysis of a hypothetical Spanish nuclear scenario, the availability of natural resources required to deploy an specific fleet of fast reactor is assessed, taking into account the breeding properties of such systems. This work also led to a publication in Energy Conversion and Management [97]. In order to perform those and other analyses, several models of the ESFR core were created for different codes. On the other hand, in order to perform safety studies of sodium fast reactors, high fidelity multidimensional analysis tools for sodium fast reactors are required. Such tools should integrate neutronic and thermal-hydraulic phenomena in a multi-physics approach. Following this motivation, the neutron diffusion code ANDES is assessed for sodium fast reactor applications. ANDES is the nodal solver implemented inside the multigroup pin-by-pin diffusion COBAYA3 code, and is based on the analytical method ACMFD. Thus, the ACMFD was verified for SFR applications and while doing so, some limitations were encountered, which are discussed through this work. In order to solve those, some new developments are proposed and implemented in ANDES. Moreover, the code was satisfactorily coupled with the thermal-hydraulic code SUBCHANFLOW, recently developed at KIT. Finally, the different implementations are verified. In addition to those developments, the node homogenized multigroup cross sections and other neutron parameters were obtained for the ESFR core using ERANOS and SERPENT codes, and employed afterwards by ANDES to perform steady state calculations. Moreover, as a result of the UPM contribution to the safety package of the CP-ESFR project, the point kinetic parameters required by the typical plant thermal-hydraulic codes were computed for the ESFR core using SERPENT, which final aim was the assessment of the impact of minor actinides in transient behaviour. All in all, the thesis provides a systematic and multi-purpose approach applied to the assessment of safety and performance parameters of Generation-IV SFR, using existing and newly developed analytical tools. An important amount of time was employed in identifying the limitations that the analytical nodal diffusion methods present when applied to fast reactors following a multigroup approach, and interesting solutions are proposed in order to overcome them.

Resistance to malathion and lambda-cyhalothrin in Ceratitis capitata (Wiedemann) (Diptera: Tephritidae)

La mosca mediterránea de la fruta, Ceratitis capitata (Wiedemann, 1824) (Diptera: Tephritidae), es una de las plagas de mayor incidencia económica en cítricos y otros frutales a nivel mundial. En España las medidas de control de esta plaga en cítricos, desde mediados de los 90 hasta 2009, se basaron principalmente en el monitoreo de las poblaciones y en la aplicación de tratamientos aéreos y terrestres con malatión cebo. Sin embargo, desde la retirada en la Unión Europea en 2009 de los productos fitosanitarios que contienen malatión, los insecticidas más utilizados para el control de esta plaga han sido lambda-cihalotrina y spinosad. En 2004-2005 se detectaron poblaciones españolas de C. capitata resistentes a malatión. Esta resistencia se ha asociado a una mutación (G328A) en la acetilcolinesterasa (AChE), a una duplicación del gen de la AChE (Ccace2) (una de las copias lleva la mutación G328A) y a resistencia metabólica mediada por esterasas (posiblemente aliesterasas). Sin embargo, cuando se secuenció la aliesterasa CcE7 en individuos de una línea resistente a malatión, no se encontró ninguna de las mutaciones (G137D y/o W251L/S/G) asociadas a resistencia en otras especies, si bien se encontraron otras mutaciones al compararlos con individuos de una línea susceptible. Asimismo, mediante la selección en laboratorio de una línea resistente a malatión (W-4Km) con lambda-cihalotrina, se ha podido obtener una línea resistente a lambda-cihalotrina (W-1K). Finalmente, se ha demostrado la capacidad de esta especie para desarrollar resistencia a spinosad mediante selección en laboratorio. Los múltiples mecanismos de resistencia identificados evidencian el potencial de esta especie para desarrollar resistencia a insecticidas con diferentes modos de acción. Los objetivos de esta tesis doctoral son: 1) evaluar la susceptibilidad de poblaciones españolas de campo de C. capitata a lambda-cihalotrina y dilucidar los mecanismos de resistencia en la línea W-1Kλ; 2) comparar la herencia, el coste biológico y la estabilidad de la resistencia a malatión mediada por la mutación G328A y la duplicación del gen Ccace2 (una de las copias lleva la mutación G328A); y 3) investigar el papel de las mutaciones identificadas en la aliesterasa CcαE7 en la resistencia a malatión. Estos estudios son de utilidad para el desarrollo de estrategias de manejo de la resistencia que puedan prevenir o retrasar la aparición de resistencia y aumentar la sostenibilidad de los insecticidas disponibles para el control de esta plaga. Nuestros resultados indican que las poblaciones españolas de C. capitata analizadas han desarrollado resistencia a lambda-cihalotrina. Los valores de CL50 estimados para las poblaciones recogidas en la Comunidad Valenciana, Cataluña y Andalucía oscilaron entre 129 ppm y 287 ppm, igualando o sobrepasando la concentración recomendada para los tratamientos de campo (125 ppm). Estos resultados contrastan con los obtenidos con tres poblaciones de campo recogidas en Túnez, cuya susceptibilidad fue similar a la de la línea control (C). La línea resistente a lambda-cihalotrina W-1K se continuó seleccionando en el laboratorio alcanzándose unos niveles de resistencia de 205 veces con respecto a la línea C, siendo su CL50 (4224 ppm) más de 30 veces superior a la concentración recomendada para los tratamientos de campo. Esta línea resistente mostró altos niveles de resistencia cruzada a deltametrina (150 veces) y a etofenprox (240 veces), lo que sugiere que el desarrollo de resistencia a lambda-cihalotrina podría comprometer la eficacia de otros piretroides para el control de esta plaga. Hemos demostrado que la resistencia de la línea W-1K a lambda-cihalotrina fue casi completamente suprimida por el sinergista PBO, lo que indica que las enzimas P450 desempeñan un papel muy importante en la resistencia a este insecticida. Sin embargo, tanto las moscas de la línea susceptible C como las de la línea resistente W-1K perdieron inmediatamente la capacidad de caminar (efecto “knock-down”) al ser tratadas tópicamente con lambda-cihalotrina, lo que sugiere que la resistencia no está mediada por alteraciones en la molécula diana (resistencia tipo “kdr”). La resistencia metabólica mediada por P450 fue analizada comparando la expresión de 53 genes CYP (codifican enzimas P450) de las familias CYP4, CYP6, CYP9 y CYP12 en adultos de la línea resistente W-1K y de la línea susceptible C. Nuestros resultados muestran que el gen CYP6A51 (número de acceso GenBank XM_004534804) fue sobreexpresado (13-18 veces) en la línea W-1K. Por otra parte, la expresión del gen CYP6A51 fue inducida tanto en adultos de la línea W-1K como de la línea C al ser tratados con lambda-cihalotrina. Sin embargo, no se obtuvieron diferencias significativas entre la línea susceptible C y la línea resistente W-1K al comparar la cantidad de P450 y la actividad NADPH-citocromo c reductasa presente en fracciones microsomales obtenidas a partir de abdómenes. Asimismo, no hemos podido correlacionar el metabolismo de deltametrina, estimado in vitro mediante la incubación de este insecticida con fracciones microsomales, con el nivel de resistencia a este piretroide observado en los bioensayos con la línea W-1K. Por otro lado, no se encontró ninguna alteración en la región promotora 5'UTR del gen CYP6A51 (-500 pb desde el inicio de la traducción) que pudiera explicar su sobreexpresión en la línea W-1K. Los datos obtenidos sugieren que la resistencia a lambda-cihalotrina en la línea W-1K está mediada por P450 y que la sobreexpresión de CYP6A51 puede desempeñar un papel importante, aunque se necesitan más evidencias para establecer una asociación directa de la resistencia con este gen. Hemos estudiado la herencia, el coste biológico y la estabilidad de la resistencia a malatión mediada por la mutación G328A y la duplicación del gen Ccace2 (una de las copias lleva la mutación G328A). La línea susceptible C, donde no se encuentra la mutación G328A (genotipo S/S), se cruzó con dos isolíneas establecidas para representar genotipos únicos correspondientes a los dos mecanismos de resistencia asociados a la molécula diana: 1) la isolínea 267Y (genotipo R/R) establecida a partir de una pareja que portaba la mutación G328A en homocigosis; 2) la isolínea 306TY (genotipo RS/RS) establecida a partir de una pareja que portaba en homocigosis la duplicación del gen Ccace2. No se realizaron cruces recíprocos, ya que mediante experimentos de hibridación in situ en cromosomas politénicos se pudo comprobar que el locus de la AChE y la duplicación (probablemente en tándem) se localizan en el cromosoma autosómico 2L. La susceptibilidad al malatión de los parentales resistentes (R/R o RS/RS) y susceptibles (S/S), los cruces F1 (S/R, S/RS y R/RS) y los retrocruzamientos indican que la resistencia a malatión es semi-dominante en ambos casos. Sin embargo, nuestros resultados no fueron concluyentes con respecto a la naturaleza monogénica de la resistencia a malatión en estas isolíneas. Por lo tanto, no podemos descartar que otros genes que contribuyan a la resistencia, además de la mutación G328A (isolínea 267Y) y de la duplicación del gen Ccace2 (isolínea 306TY), puedan haber sido seleccionados durante el proceso de selección de 267Y y 306TY. Varios parámetros biológicos fueron evaluados para determinar si estos dos mecanismos de resistencia a malatión suponen un coste biológico para los genotipos resistentes. Individuos con genotipo R/R mostraron un retraso en el tiempo de desarrollo de huevo a pupa, un peso de pupa reducido y una menor longevidad de los adultos, en comparación con los individuos con genotipo S/S. Sin embargo, el peso de pupa de los individuos con genotipo RS/RS fue similar al de los individuos S/S, y su desarrollo de huevo a pupa intermedio entre S/S y R/R. Estas diferencias en el coste biológico pueden estar relacionadas con la reducción de la eficiencia catalítica de la AChE mutada en los individuos R/R, y al efecto compensatorio que la copia no mutada del gen tiene en los individuos RS/RS que portan la duplicación. La estabilidad de la resistencia a malatión mediada por la mutación G328A y la duplicación se analizó mediante el seguimiento de los caracteres de resistencia en la progenie de retrocruzamientos S/R x R/R y S/RS x RS/RS a lo largo de varias generaciones en ausencia de presión de selección con insecticidas. Nuestros resultados muestran que la frecuencia del alelo que porta la mutación G328A disminuyó desde 67,5% en la primera generación del retrocruzamiento S/R x R/R (75% esperado, asumiendo segregación mendeliana y que sólo hay dos alelos: uno mutado y otro no mutado) a 12% después de 10 generaciones. Por el contrario, la frecuencia de la duplicación sólo disminuyó desde 75% en en la primera generación del retrocruzamiento S/RS x RS/RS (75% esperado, asumiendo segregación Mendeliana y que la duplicación segrega como un único alelo) a 50% en el mismo período, lo que indica que la duplicación es más estable que la mutación. Asimismo, se analizó la presencia de la mutación y de la duplicación en poblaciones de campo recogidas en seis localidades en 2004-2007, cuando todavía se usaba el malatión, y se comparó con poblaciones recogidas en los mismos campos en 2010, un año después de la prohibición del malatión en la Unión Europea. La frecuencia media del genotipo susceptible (S/S) aumentó del 55,9% en el período 2004-2007 a 70,8% en 2010, mientras que la frecuencia de los genotipos portadores de la mutación en homocigosis o heterocigosis (R/R y S/R) disminuyó del 30,4 al 9,2%, los que llevan la duplicación en homocigosis o heterocigosis (RS/RS y S/RS) aumentaron levemente desde 12,8 hasta 13,3%, y los que llevan a la vez la mutación y la duplicación (R/RS) también aumentaron del 1 al 6,7%. Estos resultados son consistentes con que la duplicación del gen Ccace2 (con una copia con la mutación G328A y la otra copia no mutada) es más ventajosa que la mutación G328A por si sola, ya que la duplicación mantiene los niveles de resistencia a la vez que limita el coste biológico. Para investigar la asociación entre la resistencia a malatión y las mutaciones encontradas previamente en CcE7, hemos generado isolíneas con mutaciones específicas seleccionadas por su ubicación próxima a la entrada al centro activo de la enzima. La isolínea Sm2 (procedente de una hembra heterocigota para la mutación V96L y un macho homocigoto para el alelo no mutado) mantuvo altos niveles de resistencia a malatión, incluso después de 30 generaciones sin presión de selección. Por el contrario, la isolínea 267Y (compuesta por individuos homocigotos para la mutación L267Y) y la línea 306TY (compuesta por individuos homocigotos para la doble mutación R306T-N307Y) mostraron una reducción significativa en los niveles de resistencia. También hemos encontrado que la resistencia a malatión de la línea Sm2 fue parcialmente revertida por DEF y TPP, y que Sm2 mostró una reducción significativa en la actividad MTB, como se ha descrito en otras especies que muestran resistencia específica a malatión mediada por aliesterases. Además, fue posible asociar la presencia de la mutación V96L en individuos de la línea Sm2 con supervivencia a una concentración discriminante de malatión (5,000 ppm) y con una baja actividad MTB. Estos resultados sugieren una posible relación entre la mutación V96L en la aliesterasa CcE7 y la resistencia a malatión, aunque todavía no se puede concluir que la resistencia es causada por esta mutación, siendo necesarios más estudios para comprobar su contribución a la resistencia. En conclusión, se ha encontrado por primera vez resistencia a lambda-cihalotrina en poblaciones de campo de C. capitata, y nuestros resultados indican que las P450 son el principal mecanismo de resistencia en la línea W-1K. Esta situación se suma al caso previamente descrito de resistencia en campo a malatión asociada a la mutación G328A, a la duplicación del gen Ccace2 (una de las copias lleva la mutación G328A) y a resistencia metabólica mediada por esterasas. Nuestros resultados también indican que la alteración de la molécula diana AChE parece ser responsable de un cierto nivel de resistencia a malatión en C. capitata, que puede ser estimada como aproximadamente 25-40 veces para la mutación G328A y 40-60 veces para la duplicación; mientras que la resistencia mediada por esterasas y que ha sido asociada en este estudio con la mutación V96L en CcE7 puede conferir un efecto multiplicativo (por un factor de 5 a 10) aumentando la resistencia a malatión a 200-400 veces. Por otra parte, hemos demostrado que los insectos resistentes que llevan la duplicación tienen un coste biológico menor y muestran una estabilidad mayor que aquellos con la mutación G328A en ausencia de presión de selección con insecticidas. Esto representa un escenario en el que los genotipos con la duplicación permanecerán en el campo en frecuencias bajas a moderadas, pero podrían ser seleccionados rápidamente si se utilizan malatión u otros insecticidas que muestren resistencia cruzada. Estos resultados tienen importantes implicaciones para los programas de manejo de la resistencia, ya que el repertorio de insecticidas eficaces para el control de C. capitata es cada vez más limitado. Además, la coexistencia de múltiples mecanismos de resistencia en poblaciones de campo ofrece el potencial para desarrollar resistencia frente a otros insecticidas disponibles para el control de esta plaga. Estrategias para de manejo de la resistencia basadas en la alternancia de insecticidas con diferentes modos de acción, y su combinación con otros métodos de control, deben ser implementadas para evitar el desarrollo de resistencia en campo. ABSTRACT The Mediterranean fruit fly (Medfly), Ceratitis capitata (Wiedemann, 1824) (Diptera: Tephritidae), is one of the most economically damaging pests of citrus and other fruit crops worldwide. Control measures in citrus crops in Spain from the mid 90's to 2009 were mainly based on field monitoring of population levels and aerial and ground treatments with malathion bait sprays. However, since the withdrawal of phytosanitary products containing malathion in the European Union in 2009, lambda-cyhalothrin and spinosad have become the most widely used insecticides for the control of this pest. Resistance to malathion was found in Spanish field populations of C. capitata in 2004-2005. This resistance has been associated with a mutation G328A in the acetylcholinesterase (AChE), a duplication of the AChE gene (Ccace2) (one of the copies bearing the mutation G328A), and metabolic resistance mediated by esterases (probably aliesterases). However, when the gene of the aliesterase CcE7 was sequenced in individuals from a malathion resistant strain of C. capitata, none of the known G137D and/or W251L/S/G mutations associated to resistance in other species were found, though other mutations were detected when compared with individuals from a susceptible strain. Noteworthy, a lambda-cyhalothrin resistant strain (W-1K) was obtained by selecting a field-derived malathion resistant strain (W-4Km) with lambda-cyhalothrin. Moreover, it has also been demonstrated the capacity of this species to develop resistance to spinosad by laboratory selection. The multiple resistance mechanisms identified highlight the potential of this species to develop resistance to insecticides with different modes of action. The objectives of this PhD Thesis are: 1) to assess the susceptibility of Spanish field populations of C. capitata to lambda-cyhalothrin and to elucidate the resistance mechanisms in the W-1Kλ strain; 2) to compare the inheritance, fitness cost and stability of the malathion resistance mediated by the G328A mutation and the duplication of the Ccace2 gene (with one of the copies bearing the mutation G328A); and 3) to investigate the role of the aliesterase CcαE7 mutations in malathion resistance. All these studies will be of use for devising proactive resistance management strategies that could prevent or delay resistance development and would increase the sustainability of the insecticides available for Medfly control. Our results indicate that Spanish field populations of C. capitata have developed resistance to lambda-cyhalothrin. The LC50 values estimated for populations collected at Comunidad Valenciana, Cataluña and Andalucía ranged from 129 ppm to 287 ppm, equaling or overpassing the recommended concentration for field treatments (125 ppm). These results contrast with those obtained with three different Tunisian field populations, whose susceptibility was similar to that of the control (C) strain. The lambda-cyhalothrin resistant W-1K strain has been further selected to achieve a 205-fold resistance compared to the C strain, being its LC50 (4,224 ppm) more than 30 times higher than the recommended concentration for field applications. This resistant strain showed high levels of cross-resistance to deltamethrin (150-fold) and etofenprox (240-fold), suggesting that the development of resistance to lambda-cyhalothrin may compromise the effectiveness of other pyrethroids for the control of this species. We have shown that the resistance of the W-1K strain to lambda-cyhalothrin was almost completely suppressed by the synergist PBO, indicating that P450 enzymes play a very important role in resistance to this insecticide. However, both susceptible C and resistant W-1K flies were knocked down after topical treatment with lambda-cyhalothrin, suggesting that kdr resistance mediated by alterations of the target site is not playing a major role. Metabolic resistance mediated by P450 was further analyzed by comparing the expression of 53 genes of the families CYP4, CYP6, CYP9 and CYP12 in adults flies from the resistant W-1K and the susceptible C strains. We found that the gene CYP6A51 (GenBank accession number XM_004534804) was overexpressed (13-18-fold) in the W-1K strain. Moreover, the expression of the CYP6A51 gene was induced when adults of the W-1K and C strains were treated with lambda-cyhalothrin. However, no significant differences were obtained between susceptible C and resistant W-1K strains for the quantity of P450 and for the activity of NADPH- cytochrome c reductase measured in microsomal fractions obtained from abdomens. Moreover, we failed to correlate the metabolism of deltamethrin, analyzed in vitro by incubating this insecticide with microsomal fractions, with the resistance level against this pyrethroid observed in bioassays with W-1K. The sequencing of the 5´UTR region of the CYP6A51 gene failed in finding an alteration in the promoter region (-500 bp from translation start site) that could explain overexpression in the W-1K strain. All data obtained suggest that resistance to lambda-cyhalothrin in the W- 1K strain is mediated by P450 and that overexpression of CYP6A51 may play a major role, although further evidences are needed to establish a direct association of resistance with this gene. We have studied the inheritance, fitness cost and stability of the malathion resistance mediated by the G328A mutation and the duplication of the Ccace2 gene (with one of the copies bearing the mutation G328A). The malathion-susceptible C strain where the G328A mutation is not found (S/S genotype) was crossed with two isolines established to represent unique genotypes corresponding to the two target-site resistance mechanisms: 1) the 267Y isoline (genotype R/R) was established from a couple bearing the mutation G328A in homozygosis; and 2) the 306TY isoline (genotype RS/RS) was established from a couple being homozygous for the duplication of the Ccace2 gene. Reciprocal crosses have not been performed, since in situ hybridization on polythene chromosomes showed that the AChE locus and the duplication (most probably in tandem) are placed at the autosomal chromosome 2L. Mortality responses to malathion of resistant isolines (R/R or RS/RS) and susceptible (S/S) genotypes, F1 crosses (S/R, S/RS, and R/RS), and the back-crosses indicated that resistance to malathion is inherited as a semi-dominant trait in both cases. However, our results were not conclusive about the monogenic nature of the resistance to malathion in these isolines. Thus, we can not discard that other genes contributing to resistance, in addition to the mutation G328A (isoline 267Y) and the duplication of the Ccace2 gene (isoline 306TY), may have been selected during the selection process of 267Y and 306TY. Several biological parameters were evaluated to determine if these two malathion resistance mechanisms impose a fitness cost for resistant genotypes. Individuals with genotype R/R have a reduced fitness in terms of developmental time from egg to pupa, pupal weight and adult longevity, when compared to susceptible individuals (genotype S/S). Interestingly, the fitness cost was substantially diminished in individuals with genotype RS/RS. These differences in fitness may be related to the reduction of the catalytic efficiency of mutated AChE in individuals R/R, and the compensatory effect that the non-mutated copy of the gene has on individuals RS/RS bearing the duplication. The stability of malathion reistance associated with the mutation G328A or the duplication was analyzed by following these resistant traits in the progeny of the back-crosses S/RS x RS/RS and S/R x R/R over consecutive generations in the absence of insecticide selection pressure. Our results show that the frequency of the allele bearing the mutation G328A decreased from 67.5% at the first generation of the back-cross S/R x R/R (75% expected, assuming Mendelian segregation and that there are only two alleles: one mutated and the other non-mutated) to 12% after 10 generations. By contrast, the frequency of the duplication only declined from 75% at the first generation of the back-cross S/RS x RS/RS (75% expected, assuming Mendelian segregation and that the duplication segregates as an unique allele) to 50% in the same period, indicating that the duplication is more stable than the mutation. The presence of the mutation and the duplication was analyzed in field populations collected in six localities in 2004-2007, when malathion was still used, and compared to populations collected in the same fields in 2010, one year after the prohibition of malathion in the European Union. The average frequency of the susceptible genotype (S/S) increased from 55.9% in the period 2004-2007 to 70.8% in 2010, whereas the frequency of those genotypes carrying the mutation in homozygosis or heterozygosis (R/R and S/R) declined from 30.4 to 9.2%, those carrying the duplication in homozygosis or heterozygosis (RS/RS and S/RS) increased slightly from 12.8 to 13.3%, and those carrying both the mutation and the duplication (R/RS) also increased from 1 to 6.7%. These results are consistent with the duplication of the Ccace2 gene (with one of the copies bearing the mutation G328A and the other copy non-mutated) being more advantageous than the G328A mutation alone by maintaining resistance while restoring part of the fitness. In order to investigate the association of malathion resistance with mutations previously found in the aliesterase CcE7, we have generated isolines bearing specific mutations selected by their putative location near the upper part of the active site gorge of the enzyme. The isoline Sm2 (originating from a female heterozygous for the mutation V96L and a male homozygous for the non-mutated allele) kept high levels of resistance to malathion, even after 30 generations without selection pressure. On the contrary, the isoline 267Y (composed by individuals homozygous for the mutation L267Y) and the strain 306TY (composed by homozygous for the double mutation R306T-N307Y) showed a significant reduction in the levels of resistance. We have found also that resistance to malathion in the Sm2 isoline was partially reverted by DEF and TPP, and that Sm2 showed a significant reduction in MTB activity, as reported for other species showing malathion-specific resistance mediated by aliesterases. Besides, it was possible to associate the presence of the mutation V96L in individuals from the Sm2 isoline with both survival to a discriminating concentration of malathion (5,000 ppm) and low MTB activity. Our results point out to a possible connection betwen the mutation V96L in the aliesterase CcE7 and resistance to malathion, though we can not yet conclude that the resistance is caused by the mutation, being needed further work to understand its contribution to resistance. In conclusion, resistance to lambda-cyhalothrin has been found for the first time in field populations of C. capitata, and metabolic resistance mediated by P450 appears to be the main resistance mechanism in the resistant strain W-1K. These findings add to the previously reported case of field resistance to malathion, associated to the G328A mutation and the duplication of the Ccace2 gene (with one of the copies bearing the mutation G328A) and to metabolic resistance mediated by esterases. Our results also indicate that altered target site AChE appears to be responsible for a certain level of resistance to malathion in C. capitata, that can be estimated as about 25-40-fold for the mutation G328A and 40-60-fold for the duplication; whereas metabolic resistance mediated by esterases and associated in this study with the mutation V96L in CcE7 may confer a multiplicative effect (by a factor of 5 to10) increasing malathion resistance to 200-400-fold. Moreover, we have shown that resistant insects carrying the duplication have better fitness and exhibit a higher stability than those with the mutation G328A in the absence of insecticide pressure. This represents a scenario where genotypes with the duplication will remain in the field at low to moderate frequencies, but could be rapidly selected if malathion or other insecticides showing cross-resistance are used. These findings have important implications for resistance management programs, as the repertoire of effective insecticides for C. capitata control is becoming very limited. Besides, multiple resistance mechanisms coexisting in field populations provide the potential to develop resistance to other available insecticides for the control of this pest. Appropriate resistance management strategies based on the alternation of insecticides with different modes of action, and their combination with other control methods, must then be implemented to avoid the evolution of resistance in the field.

Computational model for local damage assesment of structures

In the last years many studies have been developed to analyze the seismic behavior throug the damage concept. In fact, the evaluation of the structural damage is important in order to quantify the safety of new and existing structures and, also, to establish a framework for seismic retrofitting decision making of structures. Most proposed models are based on a post-earthquake evaluation in such a way they uncouple the computation of the structural response from that of damage. However, there are other models which include explicity the existing coupling between the degradation and the structural mechanical beaviour. Those models are closer to the physical reality and its formulation is based on the principles of Continuum Damage Mechanics. In the present work, a coupled model is formulated using a simplified application of the Continuum Damage Mechanics to the analysis of frames and allows its representation in standard finite element programs. This work is part of the activities developed by the Structural Mechanics Department (UPM) within ICONS (European Research Project on Innovative Seismic Design Concepts for New and Existing Structures).

A computational model coupling mechanics and electrophysiology in spinal cord injury

Traumatic brain injury and spinal cord injury have recently been put under the spotlight as major causes of death and disability in the developed world. Despite the important ongoing experimental and modeling campaigns aimed at understanding the mechanics of tissue and cell damage typically observed in such events, the differenti- ated roles of strain, stress and their corresponding loading rates on the damage level itself remain unclear. More specif- ically, the direct relations between brain and spinal cord tis- sue or cell damage, and electrophysiological functions are still to be unraveled. Whereas mechanical modeling efforts are focusing mainly on stress distribution and mechanistic- based damage criteria, simulated function-based damage cri- teria are still missing. Here, we propose a new multiscale model of myelinated axon associating electrophysiological impairment to structural damage as a function of strain and strain rate. This multiscale approach provides a new framework for damage evaluation directly relating neuron mechanics and electrophysiological properties, thus provid- ing a link between mechanical trauma and subsequent func- tional deficits.

A 2D computational parametric analysis of the sheltering effect of fences on a railway vehicle standing on a bridge and experiencing crosswinds

In a crosswind scenario, the risk of high-speed trains overturning increases when they run on viaducts since the aerodynamic loads are higher than on the ground. In order to increase safety, vehicles are sheltered by fences that are installed on the viaduct to reduce the loads experienced by the train. Windbreaks can be designed to have different heights, and with or without eaves on the top. In this paper, a parametric study with a total of 12 fence designs was carried out using a two-dimensional model of a train standing on a viaduct. To asses the relative effectiveness of sheltering devices, tests were done in a wind tunnel with a scaled model at a Reynolds number of 1 × 105, and the train’s aerodynamic coefficients were measured. Experimental results were compared with those predicted by Unsteady Reynolds-averaged Navier-Stokes (URANS) simulations of flow, showing that a computational model is able to satisfactorily predict the trend of the aerodynamic coefficients. In a second set of tests, the Reynolds number was increased to 12 × 106 (at a free flow air velocity of 30 m/s) in order to simulate strong wind conditions. The aerodynamic coefficients showed a similar trend for both Reynolds numbers; however, their numerical value changed enough to indicate that simulations at the lower Reynolds number do not provide all required information. Furthermore, the variation of coefficients in the simulations allowed an explanation of how fences modified the flow around the vehicle to be proposed. This made it clear why increasing fence height reduced all the coefficients but adding an eave had an effect mainly on the lift force coefficient. Finally, by analysing the time signals it was possible to clarify the influence of the Reynolds number on the peak-to-peak amplitude, the time period and the Strouhal number.

Computational Study of the Fe(CN)(2)CO Cofactor and Its Binding to HypC Protein.

In the intricate maturation process of [NiFe]-hydrogenases, the Fe(CN)2CO cofactor is first assembled in a HypCD complex with iron coordinated by cysteines from both proteins and CO is added after ligation of cyanides. The small accessory protein HypC is known to play a role in delivering the cofactor needed for assembling the hydrogenase active site. However, the chemical nature of the Fe(CN)2CO moiety and the stability of the cofactor–HypC complex are open questions. In this work, we address geometries, properties, and the nature of bonding of all chemical species involved in formation and binding of the cofactor by means of quantum calculations. We also study the influence of environmental effects and binding to cysteines on vibrational frequencies of stretching modes of CO and CN used to detect the presence of Fe(CN)2CO. Carbon monoxide is found to be much more sensitive to sulfur binding and the polarity of the medium than cyanides. The stability of the HypC–cofactor complex is analyzed by means of molecular dynamics simulation of cofactor-free and cofactor-bound forms of HypC. The results show that HypC is stable enough to carry the cofactor, but since its binding cysteine is located at the N-terminal unstructured tail, it presents large motions in solution, which suggests the need for a guiding interaction to achieve delivery of the cofactor.

Simulation of the deformation of polycrystalline nanostructured Ti by computational homogenization

Computational homogenization by means of the finite element analysis of a representative volume element of the microstructure is used to simulate the deformation of nanostructured Ti. The behavior of each grain is taken into account using a single crystal elasto-viscoplastic model which includes the microscopic mechanisms of plastic deformation by slip along basal, prismatic and pyramidal systems. Two different representations of the polycrystal were used. Each grain was modeled with one cubic finite element in the first one while many cubic elements were used to represent each grain in the second one, leading to a model which includes the effect of grain shape and size in a limited number of grains due to the computational cost. Both representations were used to simulate the tensile deformation of nanostructured Ti processed by ECAP-C as well as the drawing process of nanostructured Ti billets. It was found that the first representation based in one finite element per grain led to a stiffer response in tension and was not able to predict the texture evolution during drawing because the strain gradient within each grain could not be captured. On the contrary, the second representation of the polycrystal microstructure with many finite elements per grain was able to predict accurately the deformation of nanostructured Ti.

A contribution to appendage drag extrapolation using computational tools

In this paper, the foundations of the beta method, widely used in todays ship appendage extrapolations, are explored. The present work pretends to validate the Beta Method using experimental and computational tools. The ship used is a rounded bow tugboat with two significant appendages, namely, a midship protective structure for the propulsion system and a stern keel. The experimental and computational data was obtained through Towing Tank trials and a RANSE CFD code, respectively.

A Semantic-Based Approach to Attain Reproducibility of Computational Environments in Scientic Work ows: A Case Study

Reproducible research in scientic work ows is often addressed by tracking the provenance of the produced results. While this approach allows inspecting intermediate and nal results, improves understanding, and permits replaying a work ow execution, it does not ensure that the computational environment is available for subsequent executions to reproduce the experiment. In this work, we propose describing the resources involved in the execution of an experiment using a set of semantic vocabularies, so as to conserve the computational environment. We dene a process for documenting the work ow application, management system, and their dependencies based on 4 domain ontologies. We then conduct an experimental evaluation sing a real work ow application on an academic and a public Cloud platform. Results show that our approach can reproduce an equivalent execution environment of a predened virtual machine image on both computing platforms.

Some theoretical aspects in computational analysis of adhesive lap joints

This paper is devoted to the numerical analysis of bidimensional bonded lap joints. For this purpose, the stress singularities occurring at the intersections of the adherend-adhesive interfaces with the free edges are first investigated and a method for computing both the order and the intensity factor of these singularities is described briefly. After that, a simplified model, in which the adhesive domain is reduced to a line, is derived by using an asymptotic expansion method. Then, assuming that the assembly debonding is produced by a macro-crack propagation in the adhesive, the associated energy release rate is computed. Finally, a homogenization technique is used in order to take into account a preliminary adhesive damage consisting of periodic micro-cracks. Some numerical results are presented.

A toolbox with DERIVE: calculus on several variables, Applications of Computer Algebra

A toolbox is a set of procedures taking advantage of the computing power and graphical capacities of a CAS. With these procedures the students can solve math problems, apply mathematics to engineering or simply reinforce the learning of certain mathematical concepts. From the point of view of their construction, we can consider two types of toolboxes: (i) the closed box, built by the teacher, in which the utility files are provided to the students together with the respective tutorials and several worksheets with proposed exercises and problems,