Study of flow behaviour in a three-product cyclone using computational fluid dynamics

Simplicity in design and minimal floor space requirements render the hydrocyclone the preferred classifier in mineral processing plants. Empirical models have been developed for design and process optimisation but due to the complexity of the flow behaviour in the hydrocyclone these do not provide information on the internal separation mechanisms. To study the interaction of design variables, the flow behaviour needs to be considered, especially when modelling the new three-product cyclone. Computational fluid dynamics (CFD) was used to model the three-product cyclone, in particular the influence of the dual vortex finder arrangement on flow behaviour. From experimental work performed on the UG2 platinum ore, significant differences in the classification performance of the three-product cyclone were noticed with variations in the inner vortex finder length. Because of this simulations were performed for a range of inner vortex finder lengths. Simulations were also conducted on a conventional hydrocyclone of the same size to enable a direct comparison of the flow behaviour between the two cyclone designs. Significantly, high velocities were observed for the three-product cyclone with an inner vortex finder extended deep into the conical section of the cyclone. CFD studies revealed that in the three-product cyclone, a cylindrical shaped air-core is observed similar to conventional hydrocyclones. A constant diameter air-core was observed throughout the inner vortex finder length, while no air-core was present in the annulus. (c) 2006 Elsevier Ltd. All rights reserved.

On the chaotic instability of a nonsliding liquid-filled top with a small spheroidal base via Melnikov-Holmes-Marsden integrals

Chaotic orientations of a top containing a fluid filled cavity are investigated analytically and numerically under small perturbations. The top spins and rolls in nonsliding contact with a rough horizontal plane and the fluid in the ellipsoidal shaped cavity is considered to be ideal and describable by finite degrees of freedom. A Hamiltonian structure is established to facilitate the application of Melnikov-Holmes-Marsden (MHM) integrals. In particular, chaotic motion of the liquid-filled top is identified to be arisen from the transversal intersections between the stable and unstable manifolds of an approximated, disturbed flow of the liquid-filled top via the MHM integrals. The developed analytical criteria are crosschecked with numerical simulations via the 4th Runge-Kutta algorithms with adaptive time steps.

Plaid motion rivalry: Correlates with binocular rivalry and positive mood state

Recently Hupe and Rubin (2003, Vision Research 43 531 - 548) re-introduced the plaid as a form of perceptual rivalry by using two sets of drifting gratings behind a circular aperture to produce quasi-regular perceptual alternations between a coherent moving plaid of diamond-shaped intersections and the two sets of component 'sliding' gratings. We call this phenomenon plaid motion rivalry (PMR), and have compared its temporal dynamics with those of binocular rivalry in a sample of subjects covering a wide range of perceptual alternation rates. In support of the proposal that all rivalries may be mediated by a common switching mechanism, we found a high correlation between alternation rates induced by PMR and binocular rivalry. In keeping with a link discovered between the phase of rivalry and mood, we also found a link between PMR and an individual's mood state that is consistent with suggestions that each opposing phase of rivalry is associated with one or the other hemisphere, with the 'diamonds' phase of PMR linked with the 'positive' left hemisphere.

Ultrastructure of the spermatid of Caprimuigus europaeus Linnaeus 1758, the European Nightjar (Aves; Caprimulgidae), with phylogenetic implications

The sperm of Caprimulgus europaeus is typical of other nonpasserines in many respects. Features shared with Paleognathae and Galloanserae are the conical acrosome, shorter than the nucleus; the presence of a perforatorium and endonuclear canal; the presence of a proximal as well as distal centriole; the elongate midpiece with mitochondria grouped around a central axis (here maximally six mitochondria in similar to 10 tiers); and the presence of a fibrous or amorphous sheath around the principal piece of the axoneme. A major (apomorphic) difference from paleognaths and galloanserans is the short distal centriole, the midpiece being penetrated for most of its length by the axoneme and for only a very short proximal portion by the centriole. Nonpasserines differ from paleognaths in that the latter have a transversely ribbed fibrous sheath, whereas in nonpasserines it is amorphous, as in Caprimulgus, or absent. The absence of an annulus is an apomorphic feature of Caprimulgus, apodiform, psittaciform, gruiform, and passerine sperm, homoplastic in at least some of these. In contrast to passerines, in Caprimulgus the cytoplasmic microtubules in the spermatid are restricted to a transient longitudinal manchette. The structure of the spermatid and spermatozoon is consistent with placement of the Caprimulgidae near the Psittacidae, but is less supportive of close proximity to the Apodidae, from DNA-DNA hybridization and some other analyses.

GESTÃO DA COMUNICAÇÃO INTEGRADA: CONTRIBUIÇÕES PARA UMA ABORDAGEM SISTÊMICA Um estudo de caso da rede Magazine Luiza

O estudo investiga os fluxos de comunicação nas organizações, refletindo sobre o modelo dos 3 Puts (inputs, throughputs, outputs), que propicia uma visão sistêmica interdepartamental, aumentando a interação e a consciência entre os setores para a realização dos objetivos organizacionais. Apresenta as características e intersecções entre comunicação mercadológica, comunicação institucional e comunicação administrativa. Oferece um ponto de encontro entre esses conceitos e reflete sobre o modelo de Comunicação Integrada Tridimensional, quando todas as ações da comunicação organizacional convergem, baseadas no trinômio Missão, Visão e Valores e nos 14 passos da comunicação de Yanaze (2013). Outra análise é verificar os pressupostos teóricos com um estudo de caso da empresa Magazine Luiza, a fim de verificar de que forma o conceito de comunicação integrada está fundamentado no planejamento e na unicidade da mensagem desta organização. A metodologia consistiu em pesquisa bibliográfica, estudo de caso e aplicação de entrevistas. Entre os resultados encontrados, demonstrou-se, tanto na pesquisa teórica quanto empírica, que a abordagem sistêmica e a proposta de Comunicação 3D, de fato, oferecem caminhos para uma eficaz gestão da comunicação integrada.

Magnetic drive system for a new centrifugal rotary blood pump

The purpose of this investigation was to design a novel magnetic drive and bearing system for a new centrifugal rotary blood pump (CRBP). The drive system consists of two components: (i) permanent magnets within the impeller of the CRBP; and (ii) the driving electromagnets. Orientation of the magnets varies from axial through to 60° included out-lean (conical configuration). Permanent magnets replace the electromagnet drive to allow easier characterization. The performance characteristics tested were the axial force of attraction between the stator and rotor at angles of rotational alignment, Ø, and the corresponding torque at those angles. The drive components were tested for various magnetic cone angles, ?. The test was repeated for three backing conditions: (i) non-backed; (ii) steel-cupped; and (iii) steel plate back-iron, performed on an Instron tensile testing machine. Experimental results were expanded upon through finite element and boundary element analysis (BEM). The force/torque characteristics were maximal for a 12-magnet configuration at 0° cone angle with steel-back iron (axial force = 60 N, torque = 0.375 Nm). BEM showed how introducing a cone angle increases the radial restoring force threefold while not compromising axial bearing force. Magnets in the drive system may be orientated not only to provide adequate coupling to drive the CRBP, but to provide significant axial and radial bearing forces capable of withstanding over 100 m/s2 shock excitation on the impeller. Although the 12 magnet 0° (?) configuration yielded the greatest force/torque characteristic, this was seen as potentially unattractive as this magnetic cone angle yielded poor radial restoring force characteristics.

The influence of tool geometry on the performance of drilling tools

The main objective of the work presented in this thesis is to investigate the two sides of the flute, the face and the heel of a twist drill. The flute face was designed to yield straight diametral lips which could be extended to eliminate the chisel edge, and consequently a single cutting edge will be obtained. Since drill rigidity and space for chip conveyance have to be a compromise a theoretical expression is deduced which enables optimum chip disposal capacity to be described in terms of drill parameters. This expression is used to describe the flute heel side. Another main objective is to study the effect on drill performance of changing the conventional drill flute. Drills were manufactured according to the new flute design. Tests were run in order to compare the performance of a conventional flute drill and non conventional design put forward. The results showed that 50% reduction in thrust force and approximately 18% reduction in torque were attained for the new design. The flank wear was measured at the outer corner and found to be less for the new design drill than for the conventional one in the majority of cases. Hole quality, roundness, size and roughness were also considered as a further aspect of drill performance. Improvement in hole quality is shown to arise under certain cutting conditions. Accordingly it might be possible to use a hole which is produced in one pass of the new drill which previously would have required a drilled and reamed hole. A subsidiary objective is to design the form milling cutter that should be employed for milling the foregoing special flute from drill blank allowing for the interference effect. A mathematical analysis in conjunction with computing technique and computers is used. To control the grinding parameter, a prototype drill grinder was designed and built upon the framework of an existing cincinnati cutter grinder. The design and build of the new grinder is based on a computer aided drill point geometry analysis. In addition to the conical grinding concept, the new grinder is also used to produce spherical point utilizing a computer aided drill point geometry analysis.

Stardom in postwar France

The 1950s and 1960s were a key moment in the development of postwar France. The period was one of rapid change, derived from post-World War II economic and social modernization; yet many traditional characteristics were retained. By analyzing the eruption of the new postwar world in the context of a France that was both modern and traditional, we can see how these worlds met and interacted, and how they set the scene for the turbulent 1960s and 70s. The examination of the development of mass culture in post-war France, undertaken in this volume, offers a valuable insight into the shifts that took place. By exploring stardom from the domain of cinema and other fields, represented here by famous figures such as Brigitte Bardot, Johnny Hallyday or Jean-Luc Godard, and less conventionally treated areas of enquiry (politics [de Gaulle], literary [Françoise Sagan], and intellectual culture [Lévi-Strauss]) the reader is provided with a broad understanding of the mechanisms of popularity and success, and their cultural, social, and political roles. The picture that emerges shows that many cultural articulations remained or became identifiably French; in spite of the American mass-culture origins of these social, economic, and cultural transformations.

QoS guarantee with adaptive transmit power and message rate control for DSRC vehicle network based road safety applications

Quality of services (QoS) support is critical for dedicated short range communications (DSRC) vehicle networks based collaborative road safety applications. In this paper we propose an adaptive power and message rate control method for DSRC vehicle networks at road intersections. The design objective is to provide high availability and low latency channels for high priority emergency safety applications while maximizing channel utilization for low priority routine safety applications. In this method an offline simulation based approach is used to find out the best possible configurations of transmit power and message rate for given numbers of vehicles in the network. The identified best configurations are then used online by roadside access points (AP) according to estimated number of vehicles. Simulation results show that this adaptive method significantly outperforms a fixed control method. © 2011 Springer-Verlag.

The 'silent dilemma' of transitional justice:silencing and coming to terms with the past in Serbia

This article explores the intersections of silence and transitional justice in Serbia, where, it is often suggested, the general public is silent and indifferent about human rights abuses that took place during the former Yugoslav conflicts. It considers both the 'silent' public and the ways in which transitional justice may be complicit in silencing it. Based on scholarship that suggests silences are not absences but rather sites of silent knowledge or a result of silencing, the article explores some of the dynamics hidden within the public's silence: shared knowledge, secret practices and inability to discuss violence. It also considers the ways in which audiences subvert and resist organized transitional justice initiatives or are caught up in a 'silent dilemma' in which they are unable to speak about the past under the discursive conditions created by transitional justice practitioners.

The correlation of the indentation size effect measured with indenters of various shapes

Experimental results are presented which show that the indentation size effect for pyramidal and spherical indenters can be correlated. For a pyramidal indenter, the hardness measured in crystalline materials usually increases with decreasing depth of penetration, which is known as the indentation size effect. Spherical indentation also shows an indentation size effect. However, for a spherical indenter, hardness is not affected by depth, but increases with decreasing sphere radius. The correlation for pyramidal and spherical indenter shapes is based on geometrically necessary dislocations and work-hardening. The Nix and Gao indentation size effect model (J. Mech. Phys. Solids 46 (1998) 411) for conical indenters is extended to indenters of various shapes and compared to the experimental results. © 2002 Elsevier Science Ltd. All rights reserved.

Indentation of elastically anisotropic half-spaces by cones and parabolae of revolution

Indentation of ceramic materials with smooth indenters such as parabolae of revolution and spheres can be conducted in the elastic regime to relatively high loads. Ceramic single crystals thus provide excellent calibration media for load-and depth-sensing indentation testing; however, they are generally anisotropic and a complete elastic analysis is cumbersome. This study presents a simplified procedure for the determination of the stiffness of contact for the indentation of an anisotropic half-space by a rigid frictionless parabola of revolution which, to first order, approximates spherical indentation. Using a similar approach, a new procedure is developed for analysing conical indentation of anisotropic elastic media. For both indenter shapes, the contact is found to be elliptical, and equations are determined for the size, shape and orientation of the ellipse and the indentation modulus.

Subdifferentials of Performance Functions and Calculus of Coderivatives of Set-Valued Mappings

The paper contains calculus rules for coderivatives of compositions, sums and intersections of set-valued mappings. The types of coderivatives considered correspond to Dini-Hadamard and limiting Dini-Hadamard subdifferentials in Gˆateaux differentiable spaces, Fréchet and limiting Fréchet subdifferentials in Asplund spaces and approximate subdifferentials in arbitrary Banach spaces. The key element of the unified approach to obtaining various calculus rules for various types of derivatives presented in the paper are simple formulas for subdifferentials of marginal, or performance functions.