A Non-catalytic Deep Desulphurization Process using Hydrodynamic Cavitation

A novel approach is developed for desulphurization of fuels or organics without use of catalyst. In this process, organic and aqueous phases are mixed in a predefined manner under ambient conditions and passed through a cavitating device. Vapor cavities formed in the cavitating device are then collapsed which generate (in-situ) oxidizing species which react with the sulphur moiety resulting in the removal of sulphur from the organic phase. In this work, vortex diode was used as a cavitating device. Three organic solvents (n-octane, toluene and n-octanol) containing known amount of a model sulphur compound (thiophene) up to initial concentrations of 500 ppm were used to verify the proposed method. A very high removal of sulphur content to the extent of 100% was demonstrated. The nature of organic phase and the ratio of aqueous to organic phase were found to be the most important process parameters. The results were also verified and substantiated using commercial diesel as a solvent. The developed process has great potential for deep of various organics, in general, and for transportation fuels, in particular.

Crystallization on the Mesoscale : Self-Assembly of Iron Oxide Nanocubes into Mesocrystals

Self-assembly of nanoparticles is a promising route to form complex, nanostructured materials with functional properties. Nanoparticle assemblies characterized by a crystallographic alignment of the nanoparticles on the atomic scale, i.e. mesocrystals, are commonly found in nature with outstanding functional and mechanical properties. This thesis aims to investigate and understand the formation mechanisms of mesocrystals formed by self-assembling iron oxide nanocubes. We have used the thermal decomposition method to synthesize monodisperse, oleate-capped iron oxide nanocubes with average edge lengths between 7 nm and 12 nm and studied the evaporation-induced self-assembly in dilute toluene-based nanocube dispersions. The influence of packing constraints on the alignment of the nanocubes in nanofluidic containers has been investigated with small and wide angle X-ray scattering (SAXS and WAXS, respectively). We found that the nanocubes preferentially orient one of their {100} faces with the confining channel wall and display mesocrystalline alignment irrespective of the channel widths.  We manipulated the solvent evaporation rate of drop-cast dispersions on fluorosilane-functionalized silica substrates in a custom-designed cell. The growth stages of the assembly process were investigated using light microscopy and quartz crystal microbalance with dissipation monitoring (QCM-D). We found that particle transport phenomena, e.g. the coffee ring effect and Marangoni flow, result in complex-shaped arrays near the three-phase contact line of a drying colloidal drop when the nitrogen flow rate is high. Diffusion-driven nanoparticle assembly into large mesocrystals with a well-defined morphology dominates at much lower nitrogen flow rates. Analysis of the time-resolved video microscopy data was used to quantify the mesocrystal growth and establish a particle diffusion-based, three-dimensional growth model. The dissipation obtained from the QCM-D signal reached its maximum value when the microscopy-observed lateral growth of the mesocrystals ceased, which we address to the fluid-like behavior of the mesocrystals and their weak binding to the substrate. Analysis of electron microscopy images and diffraction patterns showed that the formed arrays display significant nanoparticle ordering, regardless of the distinctive formation process.  We followed the two-stage formation mechanism of mesocrystals in levitating colloidal drops with real-time SAXS. Modelling of the SAXS data with the square-well potential together with calculations of van der Waals interactions suggests that the nanocubes initially form disordered clusters, which quickly transform into an ordered phase.

New N-acylamino acids and derivatives from renewable fatty acids: gelation of hydrocarbons and thermal properties

This work reports the synthesis of new fatty N-acylamino acids and N-acylamino esters from the C16:0, C18:0, C18:1, and C18:1(OH) fatty acid families and demonstrates the activity of these compounds as organogel agents. Compounds were heated and dissolved in various solvents (n-hexane, toluene, and gasoline). Only saturated C16:0 and C18:0 derived from alanine were able to form gels in toluene, and saturated C16:0 derived from phenylalanine showed gelation in n-hexane. This is the first evidence that fatty N-acylamino esters and N-acylamino acid derivatives of l-serine and fatty acids C16:0, C18:0, and C18:1 are able to form gels with hexane. This observation confirms the importance of the hydroxyl group in the segment derivative of l-serine in forming good gels.

Design of experiments to optimized the determination of TDIs in agglomerated cork stoppers

Isocyanates are included into a class with an extreme commercial importance because their use in the manufacture of polyurethanes. Polyurethanes are used in several applications such as adhesives, coatings, foams, thermoplastics resins, printing inks, foundry moulds and rubbers. Agglomerated cork stoppers are currently used for still wines, semi-sparkle and gaseous wines, beer and cider. Methylene diphenyl diisocyanate (MDI) is presently the isocyanate used in the production of polyurethane based adhesive in use due to its lowest toxicity comparing with toluene diisocyanate (TDI) previously employed. However, free monomeric TDI or MDI, depending on the based polyurethane, can migrate from agglomerated cork stoppers to beverages therefore it needs to be under control. The presence of these compounds are usually investigated by HPLC with Fluorescence or UV-Vis detector depending on the derivatising agent. Ultra Performance Liquid Chromatography with Diode Array Detector (UPLC-DAD) method is replacing HPLC. The objective of this study is to determine which method is better to analyze isocyanates from agglomerated cork stoppers, essentially TDI to quantify its monomer. A Design of Experiments (DOE) with three factors, column temperature, flow and solvent, at two levels was done. Eight experiments with three replications and two repetitions were developed. Through an ANOVA the significance of the factors was evaluated and the best level’s factors were selected. As the TDI has two isomers and in this method these two isomers were not always separated an ANOVA with results of resolution between peaks was performed. The Design of Experiments reveals to be a suitable statistical tool to determine the best conditions to quantified free isocyanates from agglomerated cork stoppers to real foodstuff. The best level’s factors to maximize area was column temperature at 30ºC, flow to 0,3 mL/min and solvent 0,1% Ammonium Acetate, to maximize resolution was the same except the solvent that was 0,01% Ammonium Acetate.

Toxic metal recovery from spent hydroprocessing catalyst

Spent hydroprocessing catalysts (HPCs) are solid wastes generated in refinery industries and typically contain various hazardous metals, such as Co, Ni, and Mo. These wastes cannot be discharged into the environment due to strict regulations and require proper treatment to remove the hazardous substances. Various options have been proposed and developed for spent catalysts treatment; however, hydrometallurgical processes are considered efficient, cost-effective and environmentally-friendly methods of metal extraction, and have been widely employed for different metal uptake from aqueous leachates of secondary materials. Although there are a large number of studies on hazardous metal extraction from aqueous solutions of various spent catalysts, little information is available on Co, Ni, and Mo removal from spent NiMo hydroprocessing catalysts. In the current study, a solvent extraction process was applied to the spent HPC to specifically remove Co, Ni, and Mo. The spent HPC is dissolved in an acid solution and then the metals are extracted using three different extractants, two of which were aminebased and one which was a quaternary ammonium salt. The main aim of this study was to develop a hydrometallurgical method to remove, and ultimately be able to recover, Co, Ni, and Mo from the spent HPCs produced at the petrochemical plant in Come By Chance, Newfoundland and Labrador. The specific objectives of the study were: (1) characterization of the spent catalyst and the acidic leachate, (2) identifying the most efficient leaching agent to dissolve the metals from the spent catalyst; (3) development of a solvent extraction procedure using the amine-based extractants Alamine308, Alamine336 and the quaternary ammonium salt, Aliquat336 in toluene to remove Co, Ni, and Mo from the spent catalyst; (4) selection of the best reagent for Co, Ni, and Mo extraction based on the required contact time, required extractant concentration, as well as organic:aqueous ratio; and (5) evaluation of the extraction conditions and optimization of the metal extraction process using the Design Expert® software. For the present study, a Central Composite Design (CCD) method was applied as the main method to design the experiments, evaluate the effect of each parameter, provide a statistical model, and optimize the extraction process. Three parameters were considered as the most significant factors affecting the process efficiency: (i) extractant concentration, (ii) the organic:aqueous ratio, and (iii) contact time. Metal extraction efficiencies were calculated based on ICP analysis of the pre- and post–leachates, and the process optimization was conducted with the aid of the Design Expert® software. The obtained results showed that Alamine308 can be considered to be the most effective and suitable extractant for spent HPC examined in the study. Alamine308 is capable of removing all three metals to the maximum amounts. Aliquat336 was found to be not as effective, especially for Ni extraction; however, it is able to separate all of these metals within the first 10 min, unlike Alamine336, which required more than 35 min to do so. Based on the results of this study, a cost-effective and environmentally-friendly solventextraction process was achieved to remove Co, Ni, and Mo from the spent HPCs in a short amount of time and with the low extractant concentration required. This method can be tested and implemented for other hazardous metals from other secondary materials as well. Further investigation may be required; however, the results of this study can be a guide for future research on similar metal extraction processes.

Greener Alternatives to Selected Organic Oxidation Reactions

The study of green chemistry is dedicated to eliminating or reducing toxic waste. One route to accomplish this goal is to explore alternative reaction conditions and parameters resulting in the development of more benign synthetic routes and reagents. The primary focus of this research is to find optimal reaction conditions for the oxidation of a primary alcohol to an aldehyde. As a case study, the oxidation of benzyl alcohol to benzaldehyde, a common industrial process, was examined. Traditionally carried out using the Jones Reagent, commonly referred to as chromium (IV) oxide or chromium trioxide (CrO3) in sulphuric acid, a great deal of research went into utilizing less toxic reagents, such as MnO2 or KMnO4 supported on a clay base. This research has led to an improvement on these alternatives, using a lithium chloride (LiCl) catalyst in a montmorillonite K10 clay solid phase, together with the oxidizing agent hydrogen peroxide, as even greener alternatives to these traditional oxidizing agents. Experiments were carried out to determine the lifetime of this LiCl/clay system as compared to MnO2 and KMnO4, to investigate its ability to catalyze the oxidation of other aromatic alcohols (such as 4-methoxybenzyl alcohol and diphenylmethanol), and to further improve the system’s adherence to green chemistry principles. Green solvent alternatives were examined by replacing the toluene solvent with dimethylcarbonate (DMC), and reaction conditions were optimized to improve product yield. It was determined that the LiCl/H2O2 system was, in most cases, equally as effective at catalyzing the oxidation of benzyl alcohol to benzaldehyde. Although the catalyst and oxidizing agent eliminated the toxic waste generated from chromium reagents, it offered significant challenges in product isolation, because of an aqueous-organic phase separation.

Síntese de novos N-acilaminoácidos graxos: estudo das propriedades gelificantes

Neste trabalho é descrita a síntese de novos N-acilaminoácidos e Nacilaminoésteres graxos derivados de ácidos graxos saturados e insaturados como, por exemplo, esteárico e ricinoléico, respectivamente. Após, foi avaliada a capacidade destes compostos para a gelificação de hidrocarbonetos e as propriedades dos géis formados foram estudadas pelas técnicas de Espectroscopia de Infravermelho (IV) e Calorimetria de Varredura Diferencial (DSC). A síntese dos N-acilaminoésteres graxos foi realizada na presença de DCC, DMAP e dos respectivos aminoésteres e ácidos graxos. Os N-acilaminoésteres graxos 11-15a-d foram isolados em rendimentos que variaram de 50-84%, após 12h de reação a temperatura ambiente. Os N-acilaminoácidos graxos 16-20a-d foram obtidos a partir da hidrólise básica de 11-15a-d realizada a temperatura ambiente, em rendimentos que variaram de 34-80%. A seguir foi realizado o estudo de gelificação com todos os compostos sintetizados para verificar a influência das diferentes cadeias graxas e dos grupos laterais dos aminoácidos e aminoésteres na gelificação de tolueno, hexano e gasolina. As análises de DSC e IV mostraram que a estabilidade dos géis dependeu do tipo e do tamanho da cadeia lipofílica e também da natureza dos grupos laterais ligados ao átomo de nitrogênio. Dentre os compostos testados os compostos 17a-b de cadeia satura (C16:0 e C18:0) e 19a (C16:0), derivados da alanina e da fenilalanina, respectivamente, formaram géis em hexano, gasolina e tolueno. Pela primeira vez foram citadas as capacidades de gelificação de hidrocarbonetos pelos Nacilaminoésteres graxos 15a-b de cadeia saturada, derivados da serina, sendo os géis derivados destes compostos os mais estáveis termicamente dentre todos os obtidos.

Adsorption of aromatic compound by multi-walled carbon nanotube from sea water

It is global concern that soil and water were contaminated with organic substances such as BTEX (benzene) (B), toluene (T) and xylene (x) .The presence of excessive amounts of BTEX in aqueous surroundings may have a greatly adverse impact on water quality and thus endanger public health and welfare. Carbon nanotubes (CNT) have aroused widespread attention as a new type of adsorptions due to their outstanding ability for the removal of various inorganic and organic pollutants from large volume of wastewater. Due to variety of adsorbent and their ability to adsorb pollutant, it is possible to reduce expenses and completely omit pollutant. In this CNT is used as a new adsorbent for removal pollutant such as benzene, toluene, and xylene. The result in the area of adsorbing benzene, toluene, and xylene is as follows: the changes of pH don’t affect the capacity of adsorption and the greatest amount of adsorption occurs in pH. The greatest amount of adsorption occurs when using 0.01gr CNT oxidized. Comparing CNT with CNT oxidized in term of adsorption capacity, it is proved that the adsorption capacity of CNT oxidized is much more than CNT. The result of comparing the percentage of adsorption of mentioned elements (B, X, T) is as follows; the amount of adsorption of xylene is more than toluene and toluene is more than benzene. It should be mentioned that in this research the percentage of adsorption to measure is between to 70-80.

Análise de compostos orgânicos voláteis (BTEX) no ar da Cidade de Évora

A poluição atmosférica é um dos principais factores de degradação da qualidade de vida da população. O conjunto BTEX (benzeno, tolueno, etilbenzeno e xilenos) constitui o grupo mais importante dos compostos orgânicos voláteis (VOCs) na atmosfera uma vez que participam na química da atmosfera e constituem um perigo para a saúde, nomeadamente o benzeno, por ser altamente cancerígeno. São maioritariamente libertados pelo tráfego automóvel. Neste trabalho foi determinada a concentração dos BTEX em nove pontos da cidade de Évora no período de 21 Março a 1 de Julho de 2009 tendo-se recorrido à técnica de amostragem passiva, com amostradores Radiello™, seguida de desadsorção líquida, usando CS2, e subsequente análise por GC-MS. A concentração de benzeno no ar da cidade de Évora não excedeu o valor legislado de 5 g/m3 neste período de amostragem, sendo as concentrações obtidas para os poluentes em geral muito baixas e na sua maioria inferiores ao LOQ do método analítico. ABSTRACT; Air pollution is the major factor in the degradation of the population quality of life. BTEX (benzene, toluene, ethylbenzene and xylenes) is the most important group of volatile organic compounds (VOCs) in the atmosphere because of their role in atmospheric chemistry and the risk they posed to human health, with benzene, being a highly carcinogenic compound. BTEX are released mainly by road traffic. Concentrations of BTEX were determined at nine sampling points in the city of Évora in the period from 21 March to 1 July 2009, using passive samplers Radiello™, followed by liquid desorption with CS2, and subsequent analysis by GC-MS. During the sampling period, the concentration of benzene in the outdoor air of Évora city did not exceed 5 g/m3, the maximum value admissible by legislation. The concentrations measured of the other pollutants were, in general, very low and mostly below the LOQ of the analytical method.

Polymer microspheres: synthesis, characterisation and post-functionalisation by olefin metathesis

Porous polymer particles are used in an extraordinarily wide range of advanced and everyday applications, from combinatorial chemistry, solid-phase organic synthesis and polymer-supported reagents, to environmental analyses and the purification of drinking water. The installation and exploitation of functional chemical handles on the particles is often a prerequisite for their successful exploitation, irrespective of the application and the porous nature of the particles. New methodology for the chemical modification of macroreticular polymers is the primary focus of the work presented in this thesis. Porous polymer microspheres decorated with a diverse range of functional groups were synthesised by the post-polymerisation chemical modification of beaded polymers via olefin cross metathesis. The polymer microspheres were prepared by the precipitation polymerisation of divinylbenzene in porogenic (pore-forming) solvents; the olefin cross-metathesis (CM) functionalisation reactions exploited the pendent (polymer-bound) vinyl groups that were not consumed by polymerisation. Olefin CM reactions involving the pendent vinyl groups were performed in dichloromethane using second-generation Grubbs catalyst (Grubbs II), and a wide range of coupling partners used. The results obtained indicate that high quality, porous polymer microspheres synthesised by precipitation polymerisation in near-θ solvents can be functionalised by olefin CM under very mild conditions to install a diverse range of chemical functionalities into a common polydivinylbenzene precursor. Gel-type polymer microspheres were prepared by the precipitation copolymerisation reaction of divinylbenzene and allyl methacrylate in neat acetonitrile. The unreacted pendent vinyl groups that were not consumed by polymerisation were subjected to internal and external olefin metathesis-based hypercrosslinking reactions. Internal hypercrosslinking was carried out by using ring-closing metathesis (RCM) reactions in toluene using Grubbs II catalyst. Under these conditions, hypercrosslinked (HXL) polymers with specific surface areas around 500 m2g-1 were synthesised. External hypercrosslinking was attempted by using CM/RCM in the presence of a multivinyl coupling partner in toluene using second-generation Hoveyda-Grubbs catalyst. The results obtained indicate that no HXL polymers were obtained. However, during the development of this methodology, a new type of polymerisation was discovered with tetraallylorthosilicate as monomer.

Anisotropic Assembly of Colloidal Nanoparticles: Exploiting Substrate Crystallinity

We show that the crystal structure of a substrate can be exploited to drive the anisotropic assembly of colloidal nanoparticles. Pentanethiol-passivated Au particles of approximately 2 nm diameter deposited from toluene onto hydrogen-passivated Si(111) surfaces form linear assemblies (rods) with a narrow width distribution. The rod orientations mirror the substrate symmetry, with a high degree of alignment along principal crystallographic axes of the Si(111) surface. There is a strong preference for anisotropic growth with rod widths substantially more tightly distributed than lengths. Entropic trapping of nanoparticles provides a plausible explanation for the formation of the anisotropic assemblies we observe.

Studies on terpenes solubility in water and deep eutectic solvents diagrams for biomedical applications

The main objectives of this work are the measurement of terpenes solubility in water at different temperatures, and the formulation of Deep Eutectic Solvents based on choline chloride and polycarboxylic acids, that can be used as hydrotropes of aqueous solutions in terpenes, replacing conventional organic solvents. In this work a new experimental methodology was implemented, using dialysis membranes, for the measurement of terpenes solubility in water. Concerning the deep eutectic diagrams formulation, the determination of the melting points of the eutectic mixtures was performed using a visual method. The method used for determining solubilities was previously validated using a well-studied model compound, toluene. The experimental results of terpenes solubilities in water resulted in a very satisfactory coefficients of variation, always below 6%. The experimental solubility data were analysed and the temperature dependence is also studied in a thermodynamic perspective. The compound with the largest solubility dependence with the temperature is geraniol, while thymol presents the smallest. The phase diagrams of DES formulated were quite satisfactory, presenting always eutectic points below to 373.15 K. For some compositions, the systems composed by choline chloride and lactic, or malonic, or myristic acid were liquid at room temperature. In the case of monocarboxylic acids, eutectic is formed at 60% mol of the acid, to dicarboxylic acid is formed at 50% mol of the acid and for tricarboxylic acid these point is formed at 30% mol of the acid. In the future, it will be important to study the effect of DES as hydrotropes in aqueous solutions of terpenes. Furthermore, it would be interesting to study more terpenes in order to assess the effect of the size of the alkyl chain and the structures of the compounds.

Platinum supported on highly-dispersed ceria on activated carbon for the total oxidation of VOCs

Catalysts consisting in platinum supported on cerium oxide highly dispersed on activated carbon, with a Pt loading of 1 wt.% and ceria loadings of 5, 10 and 20 wt.% have been prepared by impregnation method and characterized by several techniques (N2 adsorption at 77 K, ICP, XRD, H2-TPR and XPS). Their catalytic behavior has been evaluated in the total oxidation of ethanol and toluene after reduction at 473 K. The obtained results show that the prepared catalysts have better performances than platinum supported on bulk CeO2. The best catalytic performance was obtained for 10 wt.% ceria loading, likely due to an optimum synergistic interaction between highly dispersed cerium oxide and platinum particles. Pt-10Ce/C achieves total conversion of ethanol and toluene to CO2 at 433 K and 453 K, respectively, and shows no deactivation during a test for 100 h. Under humid conditions (relative humidity, RH, of 40 and 80%), the activity was only slightly influenced due to the hydrophobic character of the activated carbon support, which prevents the adsorption of water.

Avaliação preliminar da contaminação por BTEX, em água subterrânea de poços tubulares, no município de Natal-RN

Among the different types of pollutants typically attributed to human activities, the petroleum products are one of the most important because of its toxic potential. This toxicity is attributed to the presence of substances such as benzene and its derivatives are very toxic to the central nervous system of man, with chronic toxicity, even in small concentrations. The area chosen for study was the city of Natal, capital of Rio Grande do Norte, where samples were collected in six different areas in the city, comprising 10 wells located in the urban area, being carried out in three distinct periods March/2009, December / June/2010 and 2009, and were evaluated for contamination by volatile hydrocarbons (BTEX - benzene, toluene, ethylbenzene and xylenes), so this work aimed to assess the quality of groundwater wells that supply funding for public supply and trade in the urban area of the city of Natal, in Rio Grande do Norte, contributing to the environmental assessment of the municipality. The analysis of BTEX in water was performed according to EPA Method 8021b. Was used the technique of headspace (TriPlus TP100) coupled to high resolution gas chromatography with selective photoionization detector (PID) and flame ionization (FID) - model Trace GC Ultra, Thermo Electron Corporation brand. The procedure adopted allowed the detection of concentrations of the order of μg.L-1. Data analysis with respect to BTEX in groundwater in the area monitored so far, shows that water quality is still preserved, because it exceeds the limits imposed by the potability Resolution CONAMA Nº. 396, April 2008

Avaliação de HPA e BTEX no solo e água subterrânea, em postos de revenda de combustíveis: estudo de caso na cidade de Natal -RN

The retail fuel stations are partially or potentially polluters and generators of environmental accidents, potentially causing contamination of underground and surface water bodies, soil and air. Leaks in fuel retail stations´ underground storage systems are often detected in Brazil and around the world. Monoaromatic hydrocarbons, BTEX (benzene, toluene, ethylbenzene and xylenes) and polycyclic aromatic hydrocarbons (PAHs) are an indication of the presence of contamination due to its high toxicity. This paper presents a case study of contamination in a Fuel Retail Station by petroleum derivative products in the city of Natal. For identification and quantification of the hydrocarbons, EPA analytical methods were used. The values of benzene quantified by EPA method 8021b CG-PID/FID, ranged from 1.164 to 4.503 mg.Kg-1 in soil samples, and from 12.10 to 27,639 μg.L-1 in underground water samples. Among the PAHs, naphthalene and anthracene showed the most significant results in soil samples, 0.420 to 15.46 mg.Kg-1 and 0.110 to 0,970 mg.Kg-1, respectively. In underground water samples, the results for Naphthalene varied between 0.759 and 614.7 μg.L-1. PAHs were quantified by EPA Method 8270 for GCMS. All of the results for the chemical analysis were compared with the values for the CONAMA 420/2009 resolution. The results for benzene (27,639 μg.L-1) showed levels highly above the recommended by the CONAMA 420 resolution, wherein the maximum permissible for underground water is 5 μg.L-1. This is a worrying factor, since underground water makes up 70% of the city of Natal´s water supply