Assessment of groundwater quality recovery strategies using nitrate transport modelling. Application to the Saône alluvial formations (Tournus, Saône-et-Loire)

To assess the efficiency of different agro-environmental strategies used to reduce groundwater pollution by nitrates, transport modelling in soils and groundwater has been carried out on two withdrawal areas in an alluvial plain. In a first time, the agro-environmental model AgriFlux allowed the simulation of water and nitrates fluxes flowing to groundwater. This model was calibrated for each agro-pedological unit of the studied territory. In a second time, the application of the hydrogeological model MODFLOW-MT3D allowed the simulation of nitrate transport in groundwater for the 1980-2004 period. This soil-groundwater coupled modelling has shown that soil nature is the first factor that conditions the vulnerability to nitrates. Thus, nitrate leaching occurs preferentially under sandy soils. Efficiency of different agro-environmental operations for groundwater quality recovery was quantified. The best results are obtained by combination of (1) grassland re-installation on sandy agricultural lots located in near well protection perimeter and (2) fertilization reduction on sandy agricultural lots located in the well alimentation area upstream the near protection perimeter. On other soils, the effect of grassland on groundwater quality improvement is more limited. Nevertheless, the control of nitrate fertilisation remains essential and is justified in both near and far well protection perimeters. Modelling thus allows optimising and priorizing agro-environmental actions in alluvial agricultural zones. [Comte J.-C., Banton O., Kockmann F., Villard A., Creuzot G. (2006), Assessment of groundwater quality recovery strategies using nitrate transport modelling. Application to the Saône alluvial formations (Tournus, Saône-et-Loire), Ingénieries Eau-Agriculture-Territoires, 45, 15-28]

Modelling solute and microorganism transport through a peri-alpine gravel aquifer by considering the aquifer as a dual porosity fractured medium.

Approach:
In-situ passive gradient comparative artificial tracer testing, undertaken using solutes (Uranine and Iodide), Bacteria (E.coli and P.putida) and bacteriophage (H40/1), permitted comparison of the mobility of different sized microorganisms relative to solutes in the sand and gravel aquifer underlying Dornach, Germany.
Tracer breakthrough curves reveal that even though uranine initially arrived at observation wells at the same time as microbiological tracers, maximum relative concentrations were sometimes less than those of microbiological tracers, while solute breakthrough curves proved more disperse.
Monitoring uranine breakthrough with depth suggested tracers arrived in observation wells in discrete 0.5m-1m thick intervals, over the aquifer’s 12m saturated thickness. Nearby exposures of aquifer material suggested that the aquifer consisted of sandy gravels enveloping sequences of open framework (OW) gravel up to 1m thick. Detailed examination of OW units revealed that they contained lenses of silty sand up to 1m long x 30cm thick., while granulometric data suggested that the gravel was two to three orders of magnitude more permeable than the enveloping sandy gravel.
Solute and microorganism tracer responses could not be simulated using conventional advective-dispersive equation solutions employing the same velocity and dispersion terms. By contrast solute tracer responses, modelled using a dual porosity approach for fractured media (DP-1D) corresponded well to observed field data. Simulating microorganism responses using the same transport terms, but no dual porosity term, generated good model fits and explained the higher relative concentration of the bacteria, compared to the non-reactive solute, even with first order removal to account for lower RR. Geologically, model results indicate that the silty units within open framework gravels are accessible to solute tracers, but not to microorganisms.
Importance:
Results highlight the benefits of geological observations developing appropriate conceptual models of solute and micro organism transport and in developing suitable numerical approaches to quantifying microorganism mobility at scales appropriate for the development of groundwater supply (wellhead) protection zones.

Biotransformation and accumulation of arsenic in soil amended with seaweed

For many coastal regions of the world, it has been common practice to apply seaweed to the land as a soil improver and fertilizer. Seaweed is rich in arsenosugars and has a tissue concentration of arsenic up to 100 micro/g g(-1). These arsenic species are relatively nontoxic to humans; however, in the environment they may accumulate in the soil and decompose to more toxic arsenic species. The aim of this study was to determine the fate and biotransformation of these arsenosugars in soil using HPLC-ICP-MS analysis. Data from coastal soils currently manured with seaweeds were used to investigate if arsenic was accumulating in these soils. Long-term application of seaweed increased arsenic concentrations in these soils up to 10-fold (0.35 mg of As kg(-1) for nonagronomic peat, 4.3 mg of As kg(-1) for seaweed-amended peat). The biotransformation of arsenic was studied in microcosm experiments in which a sandy (machair) soil, traditionally manured with seaweed, was amended with Laminaria digitata and Fucus vesiculosus. In both seaweed species, the arsenic occurs in the form of arsenosugars (85%). The application of 50 g of seaweed to 1 kg of soil leads to an increase of arsenic in the soils, and the dominating species found in the soil pore water were dimethylarsinic acid (DMA(V)) and the inorganic species arsenate (As(V)) and arsenite (As(III)) after the initial appearance of arsenosugars. A proposed decomposition pathway of arsenosugars is discussed in which the arsenosugars are transformed to DMA(V) and further to inorganic arsenic without appreciable amounts of methylarsonic acid (MA(V)). Commercially available seaweed-based fertilizers contain arsenic concentration between 10 and 50 mg kg(-1). The arsenic species in these fertilizers depends on the manufacturing procedure. Some contain mainly arsenosugars while others contain mainly DMA(V) and inorganic arsenic. With the application rates suggested by the manufacturers, the application of these fertilizers is 2 orders of magnitude lower than the maximum permissible sewage sludge load for arsenic (varies from 0.025 kg ha(-1) yr(-1) in Styria, Austria, to 0.7 kg ha(-1) yr(-1) in the U.K.), while a direct seaweed application would exceed the maximum arsenic load by at least a factor of 2.

Leatherback turtles satellite-tagged in European waters

The North Atlantic is considered a stronghold for the critically endangered leatherback sea turtle. However, limited information exists regarding the movements of individuals to and from the seas off Europe's northwesterly fringe, an area where featherbacks have been historically sighted for the past 200 yr. Here, we used satellite telemetry to record the movements and behaviour of 2 individuals bycaught in fisheries off the southwest coast of Ireland. The turtle T1 (tagged 1 September 2005; female; tracked 375 d) immediately travelled south via Madeira and the Canaries, before residing in West African waters for 3 mo. In spring, T1 migrated north towards Newfoundland where transmissions ceased. T2 (29 June 2006; male; 233 d) travelled south for a short period before spending 66 d west of the Bay of Biscay, an area previously asserted as a high-use area for leatherbacks. This prolonged high latitude summer residence corresponded with a mesoscale feature evident from satellite imagery, with the implication that this turtle had found a rich feeding site. A marked change in dive behaviour was apparent as the turtle exited this feature and provided useful insights on leatherback diving behaviour. T2 headed south in October 2006, and performed the deepest-ever dive recorded by a reptile (1280 m) southwest of Cape Verde. Unlike T1, T2 swam southwest towards Brazil before approaching the major nesting beaches of French Guiana and Surinam. Importantly, these tracks document the movement of leatherbacks from one of the remotest foraging grounds in the North Atlantic. © Inter-Research 2008.

Donegall Pass: Towards a sustainable community:Chapter 5, Health and Wellbeing

Key Points

International research has long since established a gradient between health and socio-economic status and it is now clear that the social and physical context in which people live can have a negative influence on health.

Recent research has established an adverse effect on the health of people who remained in an area that had become more deprived over time

The mechanisms thought to influence health in declining communities include stress, loss of self-esteem, stigma, powerlessness, a lack of hope and fatalism.

These mechanisms are related to the concept of social capital, a resource produced when people co-operate for mutual benefit

Residents’ key concerns relating to the decline in the community are housing shortages which are perceived to be contributing to the breakdown of the family-based community, along with traffic; pollution; non-resident parking problems; a lack of youth facilities; and the influx of ethnic minorities who are less inclined to become involved with the community

In the Donegall Pass a dual process of outward migration and business development has resulted in a decline in social capital within the community which was particularly evident amongst the younger generations

People living in deprived areas, such as the Donegall Pass, that are adjacent to affluent areas, such as the new apartment developments surrounding the area, can often feel relatively more deprived due to such direct comparisons. Although relative deprivation was evident, peer comparisons with the Donegal Road/Sandy Row community were more commonly expressed

The area can be described as a ‘food desert’ as no affordable fresh grocery supplies are available within walking distance

Residents expressed mixed opinions about the future of the Donegall Pass including a common sense of resignation towards the decline in the core community

Many residents recognise the need for people to work together and gain empowerment in order to work with the authorities (i.e., the Housing Executive and the Council) towards progressive re-development that is in keeping with the aims of the community members, however, equally many were impervious towards these suggestions feeling that previous efforts had gone unrewarded.

Wave loads on the foundation of a bottom-hinged modular flap structure

Large loads result in expensive foundations which are a substantial proportion of the capital cost of flap-type Wave Energy Converters (WECs). Devices such as Oyster 800, currently deployed at the European Marine Energy Centre (EMEC), comprise a single flap for the full width of the machine. Splitting a flap-type device into smaller vertical flap modules, to make a ‘modular-flap’, might reduce the total foundation loads, whilst still providing acceptable performance in terms of energy conversion.
This paper investigates the foundation loads of an undamped modular-flap device, comparing them to those for a rigid flap of an equivalent width. Physical modelling in a wave tank is used, with loads recorded using a six degree of freedom (DoF) load cell. Both fatigue and extreme loading analysis was conducted. The rotations of the flaps were also recorded, using a motion-tracking system.

Methods and Metrics for Fair Server Assessment under Real-Time Financial Workloads

We present a rigorous methodology and new metrics for fair comparison of server and microserver platforms. Deploying our methodology and metrics, we compare a microserver with ARM cores against two servers with ×86 cores running the same real-time financial analytics workload. We define workload-specific but platform-independent performance metrics for platform comparison, targeting both datacenter operators and end users. Our methodology establishes that a server based on the Xeon Phi co-processor delivers the highest performance and energy efficiency. However, by scaling out energy-efficient microservers, we achieve competitive or better energy efficiency than a power-equivalent server with two Sandy Bridge sockets, despite the microserver's slower cores. Using a new iso-QoS metric, we find that the ARM microserver scales enough to meet market throughput demand, that is, a 100% QoS in terms of timely option pricing, with as little as 55% of the energy consumed by the Sandy Bridge server.

SHORT-TERM EFFECTS OF SALINITY ON SOME PHYSIOLOGICAL PARAMETERS OF YOUNG OLIVE TREES OF ARBEQUINA, COBRANÇOSA AND GALEGA VARIETIES

SHORT-TERM EFFECTS OF SALINITY ON SOME PHYSIOLOGICAL PARAMETERS OF YOUNG OLIVE TREES OF ARBEQUINA, COBRANÇOSA AND GALEGA VARIETIES Ana Elisa Rato1,4, Renato Coelho1, Margarida Vaz1, Teresa Carola2, Dália Barbosa2, Nádia Silva1, José dos Santos2, Lourenço Machado2, João Godinho2, Luzia Ruas2, Margarida Barradas2, Hernani Pereira2, Sara Porfírio4 1 ICAAM, Universidade de Évora, Apartado 94, 7002-554 Évora, Portugal 2 Master students, Universidade de Évora, Apartado 94, 7002-554 Évora, Portugal 3 Ph.D. student, Universidade de Évora, Apartado 94, 7002-554 Évora, Portugal 4 aerato@uevora.pt Due to the desertification in some regions, the interest in plant’s tolerance to salinity has been increasing, as this response is determining for plant survival in stress conditions. This work reports the investigation of tolerance to salt in two year-old olive trees (Olea europaea L.) of three varieties, Arbequina, Cobrançosa and Galega vulgar. Plants were grown in 10 L plastic pots containing approximately 9 Kg of a sandy granitic soil, on a greenhouse. For 3 months (from the beginning of February to the end of April 2012), they were subjected to three levels of salinity in the irrigation water, 0 mM, 80 mM and 200 mM NaCl (6 plants per salinity level in a total of 18 plants of each variety),. Stomatal conductance (gs) and relative leaf chlorophyll content were assessed on each plant in February, March and April. Mid-day leaf water potential () and soil salinity were measured at the end of the experiment (April). On average, concerning all treatments and dates of determination, stomatal conductance of Arbequina and Galega vulgar was quite similar, around 40 mmol m-2 s-1, but Cobrançosa had a value of gs 36% higher, almost 50% higher (61 mmol m-2 s-1) when compared with the controls (0 mM salt) of the other two varieties. In percentage of controls, there was little difference in gs between varieties and between salinities during February and March. In contrast, in April, after about 90 days of exposure to salt, there was a clear decrease in gs with salt irrigation, proportional to salt concentration. Compared with controls, plants irrigated with 200 mM salt showed around 80% (Arbequina) or 85% (Cobrançosa and Galega vulgar) decrease in gs. Chlorophyll content of leaves showed less than 5% difference between varieties on the average of all treatments and dates of determination. During the course of this experiment, the salinity levels used did not show any relevant effect on chlorophyll content. Overall, at the end of the experimental period (April), leaf water potential () at midday was significantly higher in Cobrançosa (-1,4 MPa) than in Galega vulgar (-1,7 MPa) or Arbequina (-1,8 MPa), and salt decreased  of control plants (-1,25 MPa) by an average 30% (with 80 mM) and 65% (with 200 mM). At the end of the experiment, salinity in the soil irrigated with 0 mM, 80 mM or 200 mM NaCl was, on average of all varieties, 0,2 mS, 1,0 mS or 2,0 mS, respectively. Soil salinity was quite similar in Arbequina and Galega vulgar but about 35% lower in the pots of Cobrançosa, on average of all salt-irrigation levels. Plants of Cobrançosa had higher stomatal conductance, however they showed higher water potential and lower salinity in the soil. These apparently contradictory results seem to suggest that Cobrançosa responds to salt differently from the other two varieties. This issue needs further investigation.

Response to salinity in young olive trees of three Iberian varieties

Soil salinization is a problem in the Mediterranean region. This paper reports a research on the response to salt in two year-old olive trees (Olea europaea L.) of three Iberian varieties: Arbequina, Cobrançosa and Galega Vulgar. Plants were grown in plastic pots containing approximately 9 Kg of a sandy granitic soil, on a greenhouse at the University of Évora since February 2010. The experiment went from February to April 2012. As a rule, plants were watered every other day alternating salt solution (0 mM, 80 mM or 200 mM NaCl) or tap water. After three months irrigation with the different NaCl solutions, soil electric conductivity and soil water content were significantly higher on salt-irrigated pots. Salt also decreased significantly stomatal conductance (gs) and mid-day leaf water potential (), Cobrançosa having in general higher gs and but lower SLA than the two other varieties. Chlorophyll content of leaves was not affected by salt after this three months exposure to NaCl but was significantly higher on Arbequina and lower on Cobrançosa. In general, hyperspectral reflectance indexes did not show significant correlations with salt irrigation, except for the Photochemical Reflectance Index (PRI) which was clearly lower on plants of all three varieties irrigated with salt. Interestingly, Cobrançosa showed frequently vegetation indexes different from the other two varieties.

Matérias-primas da plataforma do Mondego para cerâmica

O presente trabalho divulga os resultados dos estudos levados a efeito nas matérias-primas argilosas que se integram tipologicamente na argila comum, ocorrentes na designada Plataforma do Mondego, Centro de Portugal, na região entre Miranda do Corvo, a SW, e Tábua, a NE. Para tal realizou-se a cartografia superficial dos sedimentos continentais do Cretácico e do Terciário, aí preservados, estabeleceram-se as colunas sedimentares, a nível regional e a nível local, nas áreas de maior potencial reconhecido e, caracterizaram-se as matérias-primas argilosas amostradas, em termos de composição, textura e aptidão cerâmica, objectivando a definição das zonas das jazidas com maior interesse industrial. A informação obtida e compilada, relativa ao caulino e ao feldspato é também apresentada, com vista a uma percepção da potencialidade destas matériasprimas cerâmicas ocorrentes na área. O estudo de caracterização dos materiais argilosos investigados teve como base 53 amostras obtidas em seis regiões da Plataforma do Mondego aqui definidas por motivo de organização do trabalho, segundo os critérios geográfico e geotectónico. As formações de Côja e de Campelo, do Terciário, constituem as unidades onde ocorrem litótipos produtivos, em termos de matéria-prima para a Cerâmica de Barro Vermelho ou Cerâmica de Construção. Relativamente às características texturais e composicionais, em síntese, apresentam-se os factos relevantes seguintes: A matéria-prima argilosa existente na área estudada materializa, granulometricamente, na maioria das amostras, silte, caindo os níveis amostrados com maior percentagem de argila, no domínio do silte argiloso. O défice em fracção argila implica limitações quanto à possibilidade de diversificação de produtos cerâmicos fabricados com estas matérias-primas tal-qual. Os diferentes métodos analíticos utilizados na caracterização mineralógica dos materiais amostrados confirmaram uma composição em termos dos minerais argilosos, consistindo de ilite/mica (em geral, o mais abundante), caulinite e esmectite, interestratificados e clorite. Os minerais não argilosos são quartzo (predominante), feldspato (sobretudo potássico) e hematite, com uma representação baixa. A mineralogia da fracção inferior a 2μm das amostras, não difere das amostras totais, salvo no teor mais elevado dos minerais argilosos e acentuada redução dos minerais não argilosos. Os resultados da análise química por fluorescência de raios X das amostras integrais correlacionam-se com as características mineralógicas observadas através das técnicas analíticas utilizadas. No respeitante às propriedades e comportamento cerâmico verifica-se: Os parâmetros relacionados com a plasticidade indicam que parte das pastas elaboradas com estes materiais argilosos têm uma trabalhabilidade aceitável, mas existem problemas de conformação e acentuada retracção num número significativo de amostras, devido à elevada plasticidade da maioria das amostras. A extrusão é satisfatória a óptima. A RMF e a retracção em seco assumem valores, respectivamente, moderados a baixos e moderados, embora seja necessário ter em conta o procedimento de extrusão dos provetes, sem dispositivo de vácuo. Todas as amostras foram sujeitas a cozedura a 900ºC, e um conjunto seleccionado foi cozido a 1000ºC e a 1100ºC. As fases mineralógicas ocorrentes após cozeduras a 900ºC e 1100ºC foram identificadas num conjunto de amostras, tendo-se evidenciado a coerência dessas fases, com a mineralogia das amostras em seco. Após cozedura a 900ºC, os valores de RMF das amostras satisfazem geralmente os valores mínimos, exigidos para o fabrico de tijolo, abobadilha e, com alguma frequência, de telha, como já se verificava com os valores daquela propriedade em seco. Os valores de retracção seco-cozido são em geral, modestos. A capacidade de absorção de água é maioritariamente elevada. A formação de vidro, sobretudo, condiciona o comportamento destas propriedades por cozedura dos provetes a 1000ºC e a 1100ºC. A coloração predominante em cru das matérias-primas argilosas amostradas é amarelo acastanhado a castanho avermelhado. Após cozedura a 900ºC, há um acentuado escurecimento e incremento no grau de vermelho. As cozeduras a 1000ºC e 1100ºC promovem escurecimento gradual, com ligeira influência na cor. O comportamento dos provetes após as cozeduras cerâmicas revelou-se homogéneo a cada uma das respectivas temperaturas, não se registando também defeitos significativos, nem eflorescências. A análise das amostras em termos composicionais e tecnológicos permitiu destacar as principais características e aspectos distintivos das matériasprimas, nas diferentes regiões definidas objectivando as diferentes potencialidades cerâmicas. Nesta abordagem comparativa foram consideradas só as amostras dos campos silte e silte arenoso, por serem aquelas com maior interesse para a Cerâmica de Construção. Nas colunas sedimentares das regiões de Tábua e Santa Quitéria constata-se a ocorrência de dois ritmos de sedimentação, que embora assumam características específicas em cada região, têm aspectos composicionais e tecnológicos em comum, traduzindo melhor aptidão cerâmica os ritmos inferiores. A conjugação da cartografia realizada com os estudos laboratoriais permite concluir que as regiões de Tábua e de Santa Quitéria serão as que têm maior potencial por explorar, em matéria-prima para Cerâmica de Construção, apesar da primeira já ser intensamente explorada. Na região de Tábua, as amostras têm como fases mineralógicas principais ilite e quartzo na mesma proporção média (35%) e caulinite (média=19%) que regista enriquecimento significativo na fracção argila (média=38%). As argilas desta região registam a cor em cru mais vermelha e pH mais ácido observados. O ritmo de sedimentação inferior, com esmectite e interestratificados e ligeiramente menos quartzoso, apresenta melhores propriedades cerâmicas. A composição mineralógica média das amostras da região de Santa Quitéria é próxima daquela da região de Tábua, mas menos caulinítica, em especial na sequência inferior, na qual o teor médio de caulinite na fracção argila (7%) é o mais baixo observado. Na região de Côja – Arganil, a actividade extractiva é significativa na bacia de Côja. Aqui, a exploração de novas áreas potenciais é condicionada pela cobertura conglomerática e por estruturas tectónicas e não tectónicas relacionadas com comportamento plástico. Na restante área desta região, os recursos argilosos são penalizados por material areno-conglomerático. As amostras desta região distinguem-se das restantes a nível textural pela maior fracção areia e mineralogicamente pela presença de clorite, teor reduzido de caulinite e elevado de feldspato. As potencialidades em barro vermelho na região de Sanguinheda não serão significativas, pois a Formação de Côja é predominantemente arcósica e a Formação de Campelo pouco espessa e conglomerática. As argilas com melhor aptidão cerâmica foram amostradas na região de Miranda do Corvo – Lousã. Na composição, estas amostras são as que contêm maior fracção de argila, maior teor de ilite e caulinite e menor de argilas expansivas. Registam os melhores valores nas características tecnológicas, nomeadamente a RMF e absorção de água. A consistência dos grupos amostrais e ritmos definidos em termos composicionais e tecnológicos é corroborada pelas técnicas de análise estatística multivariada aplicadas, que os identificam. As condições de amostragem na região de Tábua, permitiram a elaboração de uma coluna tipológica, na qual, a partir de uma caracterização expedita de amostras é possível identificar a sua afinidade com os ritmos argilosos definidos e, consequentemente, a sua situação na coluna sedimentar regional e aptidão cerâmica. A cartografia dos recursos argilosos potenciais, elaborada à escala 1:25.000, constitui um dos objectivos principais deste trabalho e nela constam unidades litológicas, nas quais são diferenciadas unidades argilosas tendo também em consideração a tipologia e guias mineralógicos resultantes da caracterização das amostras. As características composicionais destas unidades denotam diferente aptidão cerâmica e, portanto, permitem salientar as zonas com maior interesse económico.

A revision of the polychaete family Nephtyidae, based on morphological and molecular data

A família Nephtyidae é uma das mais frequentes em habitats costeiros e marinhos de todo o mundo. São organismos errantes típicos de sedimentos arenosos e lodosos, ocorrendo frequentemente no domínio costeiro até 100 m de profundidade, e mais raramente em profundidades batiais e abissais. As primeiras espécies descritas foram o Nephtys caeca (Fabricius, 1780) e o N. ciliata (O. F. Müller, 1789), ambas atribuídas inicialmente ao género Nereis e posteriormente transferidas para o género Nephtys por Savigny, em 1818. A família Nephtyidae foi criada em 1851 por Grube para o género Nephtys Cuvier, 1817. No âmbito desta tese é feito um estudo taxonómico e filogenético da família Nephtyidae. O estudo filogenético inclui dados morfológicos e moleculares de 24 taxa representantes dos cinco géneros da família, Nephtys Cuvier, 1817, Aglaophamus Kinberg, 1866, Micronephthys (Friedrich, 1939), Inermonephtys Fauchald, 1967 e Dentinephtys Imajima e Takeda, 1987. A análise evidenciou dois grandes grupos correspondentes aos dois principais géneros, Aglaophamus e Nephtys. Duas espécies do género Nephtys (N. pulchra e N. australiensis) são transferidas para o género Aglaophamus, e consequentemente são propostas novas diagnoses para os géneros. O género Dentinephtys é sinonimizado com Nephtys e um novo género, Bipalponephtys, é descrito para acomodar as espécies Nephtys cornuta, N. danida e Micronephthys neotena. As relações filogenéticas entre os géneros são discutidas. Do estudo taxonómico resultou a revisão da família Nephtyidae para o Sul da Europa (entre o Canal da Mancha e o Mediterrâneo), com a descrição de uma nova espécie, Inermonephtys foretmontardoi. A espécie Micronephthys maryae é sinonimizada com M. stammeri. Para cada espécie são incluídas notas sobre a sua ecologia bem como a distribuição geográfica e batimétrica. São propostas novas diagnoses para os géneros do Sul da Europa bem como uma chave de identificação taxonómica para as espécies desta região. Após uma exaustiva revisão bibliográfica da família, e da observação de material museológico relativo a 44 espécies, foi compilada uma lista completa para a família de 128 espécies, distribuídas por cinco géneros (57 Nephtys, 53 Aglaophamus, sete Micronephthys, oito Inermonephtys e três Bipalponephtys), na qual são incluídas sinonímias e considerações taxonómicas para cada espécie. A espécie Nephtys serrata é sinonimizada com N. serratifolia. São apresentados as distribuições geográficas e batimétricas das diferentes espécies e notas sobre o seu habitat. São também incluídas tabelas de identificação com as principais características taxonómicas das espécies. O valor diagnóstico dos caracteres morfológicos é discutido. Vários problemas taxonómicos são realçados, indicando a necessidade de revisões adicionais para 23 espécies. Este trabalho realça a existência de vários problemas taxonómicos e filogenéticos dentro da família Nephtyidae, podendo ser considerado como a base para estudos futuros. Análises filogenéticas adicionais incluindo dados morfológicos e moleculares de um maior número de espécies vão certamente conduzir a uma melhor avaliação do estatuto e relações entre os géneros dentro da família.