The hot working flow stress and microstructure in magnesium AZ31

The evolution of flow stress and microstructure for wrought magnesium alloy AZ31 was characterised using torsion and compression testing. Temperatures ranging between 300°C and 450°C and strain rates between 0.001s^-1 and 1s^-1, were employed. Constitutive equations were developed for the flow stress at a strain of 1.0 for torsion, and 0.6 for compression. The flow stress was found to be strongly dependent on deformation mode at low strains. This can be explained in terms of the influence of the deformation accommodating processes of prismatic slip and dynamic recrystallisation (DRX). At higher strains, when the change in flow stress with strain is lower, the flow stress was relatively insensitive to deformation mode. Optical microscopy carried out on torsion samples quenched after twisting to strains between 0.2 and 2 revealed dynamically recrystallised (DRX) grains situated on pre-existing grain boundaries. The average grain size was reduced from 22.5μm down to 7.3 μm after a strain of 2, with the initial grain size being halved after a strain of 0.5.

The effect of deformation twinning on stress localization in a three dimensional TWIP steel microstructure

We present an investigation of the effect of deformation twinning on the visco-plastic response and stress localization in a low stacking fault energy twinning-induced plasticity (TWIP) steel under uniaxial tension loading. The three-dimensional full field response was simulated using the fast Fourier transform method. The initial microstructure was obtained from a three dimensional serial sectionusing electron backscatter diffraction. Twin volume fraction evolution upon strain was measured so the hardening parameters of the simple Voce model could be identified to fit both the stress-strain behavior and twinning activity. General trends of texture evolution were acceptably predicted including the typical sharpening and balance between the 1 1 1 fiber and the 1 0 0 fiber. Twinning was found to nucleate preferentially at grain boundaries although the predominant twin reorientation scheme did not allow spatial propagation to be captured. Hot spots in stress correlated with the boundaries of twinned voxel domains, which either impeded or enhanced twinning based on which deformation modes were active locally.

Microstructure and texture evolution during tensile deformation of symmetric/asymmetric-rolled low carbon microalloyed steel

The deformation and fracture mechanisms of a low carbon microalloyed steel processed by asymmetric rolling (AsR) and symmetric rolling (SR) were compared by microstructural and texture evolutions during uniaxial tensile deformation. A realistic microstructure-based micromechanical modeling was involved as well. AsR provides more effective grain refinement and beneficial shear textures, leading to higher ductility and extraordinary strain hardening with improved yield and ultimate tensile stresses as well as promoting the occurrence of ductile fracture. This was verified and further explained by means of the different fracture modes during quasi-static uniaxial deformation, the preferred void nucleation sites and crack propagation behavior, and the change in the dislocation density based on the kernel average misorientation (KAM) distribution. The equivalent strain/stress partitioning during tensile deformation of AsR and SR specimens was modeled based on a two-dimensional (2D) representative volume element (RVE) approach. The trend of strain/stress partitioning in the ferrite matrix agrees well with the experimental results.

Impact of grain microstructure on the heterogeneity of precipitation strengthening in an Al-Li-Cu alloy

The effect of grain microstructure on the age-hardening behavior is investigated on recrystallized and un-recrystallized Al-Cu-Li alloys by combining electron-backscatter-diffraction and micro-hardness mapping. The spatial heterogeneity of micro-hardness is found to be strongly dependent on the grain microstructure. Controlled experiments are carried out to change the pre-strain before artificial ageing. These experiments lead to an evaluation of the range of local strain induced by pre-stretching as a function of the grain microstructure and results in heterogeneous formation of the hardening T1 precipitates.

A microstructure based analytical model for tensile twinning in a rod textured Mg alloy

Abstract A model for tensile twinning during the compression of rod textured magnesium is developed based on the idea that these twins nucleate at grain boundaries and that when the twin number density per grain is low these twins readily give rise to the formation of other 'interaction' twins in adjacent grains. Experimental observations of twin aspect ratios measured at a single grain size and twin number densities measured over four grain sizes were used to determine model material parameters. Using these, the model provides reasonable predictions for the observed magnitudes and trends for the following observations:Effect of grain size and stress on twin volume fraction, fractional twin length and the fraction of twin contact.Effect of grain size on the yield stress.Effect of grain size on the general shape of the stress-strain curve at low strains. A parametric study shows the model to be quite robust but that it is particularly sensitive to the value of the exponent assumed for the twin nucleation rate law. It is seen that preventing the formation of interaction twins provides an important avenue for hardening and that the flow stress is also particularly sensitive to the relaxation of the twin back stresses. The model shows the importance of taking microstructure into account when modelling twinning.

Microstructure and corrosion of AA2024

AA2024-Tx is one of the most common high-strength aluminium alloys used in the aerospace industry. This article reviews current understanding of the microstructure of sheet AA2024-T3 and chronicles the emergence of new compositions for constituent particles as well as reviews older literature to understand the source of the original compositions. The review goes on to summarise older and more recent studies on corrosion of AA2024-T3, drawing attention to areas of corrosion initiation and propagation. It pays particular attention to modern approaches to corrosion characterisation as obtained through microelectrochemical techniques and physicochemical characterisation, which provide statistical assessment of factors that contribute to corrosion of AA2024. These approaches are also relevant to other alloys.

Effect of heat treatment on diffusion, internal friction, microstructure and mechanical properties of ultra-fine-grained nickel severely deformed by equal-channel angular pressing

Severe plastic deformation via equal-channel angular pressing was shown to induce characteristic ultra-fast diffusion paths in Ni (Divinski et al., 2011). The effect of heat treatment on these paths, which were found to be represented by deformation-modified general high-angle grain boundaries (GBs), is investigated by accurate radiotracer self-diffusion measurements applying the 63Ni isotope. Redistribution of free volume and segregation of residual impurities caused by the heat treatment triggers relaxation of the diffusion paths. A correlation between the GB diffusion kinetics, internal friction, microstructure evolution and microhardness changes is established and analyzed in detail. A phenomenological model of diffusion enhancement in deformation-modified GBs is proposed.

Influence of cooling rate on the microstructure and corrosion behavior of Al-Fe alloys

The effect of Fe in Al is technologically important for commercial Al-alloys, and in recycled Al. This work explores the use of the novel rapid solidification technology, known as direct strip casting, to improve the recyclability of Al-alloys. We provide a comparison between the corrosion and microstructure of Al-Fe alloys prepared with wide-ranging cooling rates (0.1. °C/s to 500. °C/s). Rapid cooling was achieved via direct strip casting, while slow cooling was achieved using sand casting. Corrosion was studied via polarisation and immersion tests, followed by surface analysis using scanning electron microscopy and optical profilometry. It was shown that the corrosion resistance of Al-Fe alloys is improved with increased cooling rates, attributed to the reduced size and number of Fe-containing intermetallics.

Microstructure and mechanical properties of wrought and additive manufactured Ti-6Al-4V cylindrical bars

Titanium alloys are widely used in various engineering design application due to its superior material properties. The traditional manufacturing of titanium products is always difficult, time consuming, high material wastage and manufacturing costs. Selective laser melting (SLM), an additive manufacturing technology has widely gained attention due to its capability to produce near net shape components with less production time. In this technical paper,microstructure,chemical composition,tensile properties and hardness are studied for the wrought and additive manufactured SLM cylindrical bar. Microstructure,mechanical properties and hardness were studied in both the longitudinal and transverse directions of the bar to study the effect of orientation. It was found that additive manufactured bar have higher yield strength, ultimate tensile strength and hardness than the wrought bar. For both conventional and SLM test samples, the yield strength, ultimate tensile strength and hardness was found to be high in the transverse direction. The difference in the properties can be attributed to the difference in microstructure as a result of processing conditions. The tensile fracture area was quantified by careful examination of the fracture surfaces in the scanning electron microscope.

Orientation dependence of the deformation microstructure in a Fe-30Ni-Nb model austenitic steel subjected to hot uniaxial compression

The present work was aimed at a detailed investigation of the orientation dependence of the microstructure characteristics in a Fe-30Ni-Nb austenitic model steel subjected to hot uniaxial compression at 1198 K (925 °C) at a strain rate of 1 s−1 to several strain levels up to 1.0. The quantification of the substructure evolution as a function of strain was performed for the stable 〈011〉 oriented grains. Other grain orientations were also investigated in detail at a strain of 0.2. The 〈110〉 oriented grains contained self-screening arrays of “microbands” (MBs) aligned with high Schmid factor {111} slip planes. The MB crystallographic alignment was largely maintained up to a strain of 1.0, which suggests that the corresponding boundaries kept continuously rearranging themselves during straining and did not follow the sample shape change. The mean MB spacing decreased and misorientation angle increased with strain towards saturation, indicating the operation of the “repolygonization” dynamic recovery mechanism. The non-〈011〉 oriented grains displayed a strong tendency to split during deformation into deformation bands having alternating orientations and being mutually rotated by large angles. The bands were separated by transition regions comprising arrays of closely spaced, extended sub-boundaries collectively accommodating large misorientations across very small distances.

Effect of single and double austenitization treatments on the microstructure and hardness of AISI D2 tool steel

This investigation is concerned with the study of effect of Double Austenitization (DA) and Single Austenitization (SA) heat treatment processes on microstructure and mechanical property of AISI D2type cold worked tool steel. To maximize hardness, tool steels are used in a quenched and tempered condition. This involves heating the material to the austenitizing temperature (~850-1100. °C), quenching at an appropriate rate to form martensite, and tempering to reduce the retained austenite content and induce toughness. The merits of DA treatment isto promote dissolution of carbides at the same time proscribe grain coarsening significantly was attempted in D2 tool steel. The study has found that DA treatment has induced high hardness with insignificant growth in grains. The increase in hardness is attributed to increase in carbon content in matrix due to dissolution of carbides; whereas finer grains due to role of inclusions.

Microstructure development and solute behaviour in Fe-C and Fe-C-V alloys during strip casting and secondary processing

 Strip casting is a rapid, environment friendly technology for manufacturing thin sheets of steel directly from molten metal. Research presented in this thesis examines the effect of atomic location, cluster size and composition on internal microstructure development during strip casting. Current research potentially leads to green manufacturing of steel.

The Brazilian foreign exchange market through the microstructure perspective

The objective of this study is to investigate whether the relationship between order ow and the spot exchange rate stems from the fact that the ow aggregates information on dispersed economic fundamentals in the economy. To perform this test, a database that includes all transactions of the commercial and nancial segments of the Brazilian primary foreign exchange market between January of 1999 and May of 2008 was used. We show that the order ow was partly responsible for variations in in ation expectations over the time period and that this relationship did not remain robust, drawing comparisons with other fundamentals such as GDP and Industrial Production.

Interface microstructure of alumina mechanically metallized with Ti brazed to Fe–Ni–Co using different fillers

NASCIMENTO,R.M. et al.Interface microstructure of alumina mechanically metallized with Ti brazed to Fe–Ni–Co using different fillers. Materials Science and Engineering A, v.466, n.1/2, p. 195-200, 2007.