Variations of local heat transfer coefficient in piped flow of viscous liquids

Measurements were carried out to determine local coefficients of heat transfer in short lengths of horizontal pipe, and in the region of an discontinuity in pipe diameter. Laminar, transitional and turbulent flow regimes were investigated, and mixtures of propylene glycol and water were used in the experiments to give a range of viscous fluids. Theoretical and empirical analyses were implemented to find how the fundamental mechanism of forced convection was modified by the secondary effects of free convection, temperature dependent viscosity, and viscous dissipation. From experiments with the short tube it was possible to determine simple empirical relationships describing the axial distribution of the local 1usselt number and its dependence on the Reynolds and Prandtl numbers. Small corrections were made to account for the secondary effects mentioned above. Two different entrance configurations were investigated to demonstrate how conditions upstream could influence the heat transfer coefficients measured downstream In experiments with a sudden contraction in pipe diameter the distribution of local 1u3se1t number depended on the Prandtl number of the fluid in a complicated way. Graphical data is presented describing this dependence for a range of fluids indicating how the local Nusselt number varied with the diameter-ratio. Ratios up to 3.34:1 were considered. With a sudden divergence in pipe diameter, it was possible to derive the axial distribution of the local Nusse1t number for a range of Reynolds and Prandtl numbers in a similar way to the convergence experiments. Difficulty was encountered in explaining some of the measurements obtained at low Reynolds numbers, and flow visualization techniques wore used to determine the complex flow patterns which could lead to the anomalous results mentioned. Tests were carried out with divergences up to 1:3.34 to find the way in which the local Nusselt number varied with the diameter ratio, and a few experiments were carried out with very large ratios up .to 14.4. A limited amount of theoretical analysis of the 'divergence' system was carried out to substantiate certain explanations of the heat transfer mechanisms postulated.

Factors affecting the durability of 5.25 inch floppy diskette media and its mechanisms of wear

This project is targeted towards establishing the durability and mechanisms of wear involved in the use of 5.25 inch magnetic floppy diskettes with particular reference to the media manufactured by the Minnesota Mining and Manufacturing Company, 3M Center, St. Paul, Minnesota, USA. In the present work most stress has been laid on the presentation of the conclusions drawn from the results obtained using samples produced specifically for this project. These samples were produced on the pilot plant at 3MTM, St. Paul, USA and are identified by the code 58759-4 with sample numbers SR1 to SR4 each with different lubrication conditions. All of the categories have been produced with four different surface roughnesses by varying the degree of burnishing. It has been found that the mechanisms of wear are related to a fatigue process. Some surprises have been noted in respect of the value of burnishing compared to the observations made elsewhere. Good reasons for these observed differences have been noted, however, and it will be shown that these are merely superficial and not concerned with wear of any real type. The present work reports the effects of the changes in the media's lubrication status and its surface topography as well as presenting evidence for the suggested wear mechanisms.

Local shell-side coefficients in shell and tube exchanges the use of a mass transfer technique

A diffusion-controlled electrochemical mass transfer technique has been employed in making local measurements of shell-side coefficients in segmentally baffled shell and tube heat exchangers. Corresponding heat transfer data are predicted through the Chilton and Colburn heat and mass transfer analogy. Mass transfer coefficients were measured for baffle spacing lengths of individual tubes in an internal baffle compartment. Shell-side pressure measurements were also made. Baffle compartment average coefficients derived from individual tube coefficients are shown to be in good agreement with reported experimental bundle average heat transfer data for a heat exchanger model of similar geometry. Mass transfer coefficients of individual tubes compare favourably with those obtained previously by another mass transfer technique. Experimental data are reported for a variety of segmental baffle configurations over the shell-side Reynolds number range 100 to 42 000. Baffles with zero clearances were studied at three baffle cuts and two baffle spacings. Baffle geometry is shown to have a large effect on the distribution of tube coefficients within the baffle compartment. Fluid "jetting" is identified with some baffle configurations. No simple characteristic velocity is found to correlate zonal or baffle compartment average mass transfer data for the effect of both baffle cut and baffle spacing. Experiments with baffle clearances typical of commercial heat exchangers are also reported. The effect of leakage streams associated with these baffles is identified. Investigations were extended to double segmental baffles for which no data had previously been published. The similarity in the shell-side characteristics of this baffle arrangement and two parallel single segmental baffle arrangements is demonstrated. A general relationship between the shell-side mass transfer performance and pressure drop was indicated by the data for all the baffle configurations examined.

Physical and chemical factors influencing the germination of Clostridium difficile spores

AIMS: To investigate the influence of chemical and physical factors on the rate and extent of germination of Clostridium difficile spores. METHODS AND RESULTS: Germination of C. difficile spores following exposure to chemical and physical germinants was measured by loss of either heat or ethanol resistance. Sodium taurocholate and chenodeoxycholate initiated germination together with thioglycollate medium at concentrations of 0.1-100 mmol l(-1) and 10-100 mmol l(-1) respectively. Glycine (0.2% w/v) was a co-factor required for germination with sodium taurocholate. There was no significant difference in the rate of germination of C. difficile spores in aerobic and anaerobic conditions (P > 0.05) however, the initial rate of germination was significantly increased at 37 degrees C compared to 20 degrees C (P < 0.05). The optimum pH range for germination was 6.5-7.5, with a decreased rate and extent of germination occurring at pH 5.5 and 8.5. CONCLUSIONS: This study demonstrates that sodium taurocholate and chenodeoxycholate initiate germination of C. difficile spores and is concentration dependant. Temperature and pH influence the rate and extent of germination. SIGNIFICANCE AND IMPACT OF THE STUDY: This manuscript enhances the knowledge of the factors influencing the germination of C. difficile spores. This may be applied to the development of potential novel strategies for the prevention of C. difficile infection.

Factors determining the morphology of β-amyloid (Aβ) deposits in Down's syndrome

Immunostained preparations of the medial temporal lobe from patients with Down's syndrome (DS) were counterstained with cresyl violet to reveal the β-amyloid (Aβ) deposits and their associated cell populations. Aβ deposits in the cornu Ammonis (CA) of the hippocampus were, on average, more strongly stained, less often directly associated with neurons and more often associated with glial cells than the adjacent areas of cortex. Cored deposits were more frequently recorded in sulci rather than gyri and were associated with more glial cells than the uncored deposits. Multiple regression analyses suggested there was a positive correlation in the cortex between Aβ deposit size and the frequency of closely associated neurons, the correlation being most significant with larger (>25 μm) neurons. The morphology of Aβ deposit was also correlated with the location of deposits in the cortex, CA and dentate gyrus but this factor was of lesser importance. No significant variation in the morphology of the Aβ deposits was associated with the presence of blood vessels within or adjacent to the deposit. The data suggest that neuronal cell bodies are important in the initial formation of Aβ deposits and glial cells with the development of more mature amyloid deposits.

Factors associated with degeneration of the thallus centre in foliose lichens

Degeneration of the older parts of foliose lichen thalli often lead to the formation of a space or 'window' in the centre of the colonies. The percentage of thalli of different size which exhibited 'windows' was studied in twenty saxicolous lichen populations in south Gwynedd, Wales. The proportion of thalli with 'windows' increased with thallus size. The size class at which 50% and 100% of thalli exhibited 'windows' varied between populations. Differences between populations were not correlated with distance from the sea, aspect, slope or porosity of the substrate or the total number of lichen species present. However, a higher percentage of smaller thalli had 'windows' on rock surfaces with a greater lichen cover. There were no significant differences in the levels of Ca, Mg, Cu or Zn in large (>4 cm) and small (<2 cm) Parmelia conspersa (Ehrh. ex Ach.) Ach. thalli or in the centres and marginal lobes of these thalli. The concentration of ribitol, arabitol and mannitol was significantly reduced in the centre of large thalli compared with the margin of large thalli and the centre of small thalli. However, carbohydrate levels were similar in the centre of large thalli and the margin of small thalli. The data suggest that loss of the thallus centre is a degenerative process related to thallus size. In the field, the formation of 'windows' may be related to the intensity of competition on a substrate. Central degeneration was not associated with a deficiency or an accumulation of Ca, Mg, Cu and Zn in the thallus centre. However, degeneration may be associated with a reduction in carbohydrates in the centre compared with the marginal lobes.

Extrinsic factors in the perception of bistable motion stimuli

When viewing a drifting plaid stimulus, perceived motion alternates over time between coherent pattern motion and a transparent impression of the two component gratings. It is known that changing the intrinsic attributes of such patterns (e.g. speed, orientation and spatial frequency of components) can influence percept predominance. Here, we investigate the contribution of extrinsic factors to perception; specifically contextual motion and eye movements. In the first experiment, the percept most similar to the speed and direction of surround motion increased in dominance, implying a tuned integration process. This shift primarily involved an increase in dominance durations of the consistent percept. The second experiment measured eye movements under similar conditions. Saccades were not associated with perceptual transitions, though blink rate increased around the time of a switch. This indicates that saccades do not cause switches, yet saccades in a congruent direction might help to prolong a percept because i) more saccades were directionally congruent with the currently reported percept than expected by chance, and ii) when observers were asked to make deliberate eye movements along one motion axis, this increased percept reports in that direction. Overall, we find evidence that perception of bistable motion can be modulated by information from spatially adjacent regions, and changes to the retinal image caused by blinks and saccades.

Antecedents and consequences of market orientation : an examination in the joint ventures' relational context

Market oriented behaviours have been found to be important predictors of business success across a wide array of studies. Despite their potential importance, research into market oriented behaviours in the joint venture (JV) context is very scarce. This study represents a novel attempt to address this gap by examining a set of antecedent factors which arises from sources outside a traditional firm’s boundary. An extensive review and synthesis of the market orientation and JV literature yielded a set of context-specific antecedent factors relevant to the JV’s relational context. In accordance with the perspective offered by the transaction cost theory, a system of hypotheses about the effects of these antecedent factors on JV’s market oriented behaviours was developed. In order to test these hypotheses, empirical evidence was collected by means of a mail survey to international joint ventures operating in the coastal regions of mainland China. A sample of 191 JV firms was collected as a result. Following well established procedures for scale development and purification as recommended in the methodology literature, the scales were critically trimmed and reviewed for their psychometric properties. The conceptual model was tested with a structural equation model. Results suggested that a number of context-specific antecedents are in fact important determinants of JVs’ level of market oriented behaviours. In addition, the linkage between market oriented behaviours and market performance was also successfully established.

The role of insulin and the insulin-like growth factors in the proliferation of the rat thymic lymphocyte

Concanavalin A, provoked a 35-fold increase in the rate of proliferation of rat thymocytes. Insulin (10-6M), and insulin-like growth factor I (10-10M) approximately doubled the rate of DNA synthesis. Both of these structurally related molecules acted through the type I insulin-like growth factor receptor. The sequential addition of Concanavalin A and insulin, promoted a much greater proliferative response than to either of the two agonists alone. Insulin also increased the uptake of glucose and amino acids by the cells. Glucose uptake was enhanced at insulin concentrations of 10-6M and 10-10M. Amino acid uptake was more strongly affected at the higher concentration. Insulin-like growth factor I (10-11M) also enhanced amino acid uptake. The effects of insulin on metabolism were mediated by both insulin and type I insulin-like growth factor receptors. These effects were greatly enhanced after a pre-treatment with Concanavalin A. Concanavalin A provided a primary mitogenic signal to the cells. Amongst the responses was an increased expression of insulin and/or type I insulin-like growth factor receptors. The consequent enhanced cellular sensitivity to these agonists, enabled them to facilitate the passage of the cells through the cell cycle by: i) providing a secondary mitogenic signal, and ii) promoting the uptake of raw materials and energy substrates. The initiation of DNA synthesis and passage through the cell cycle was thus punctuated by the sequential expression of various cell surface receptors. This regulated cellular sensitivity, enabling them to react in a precisely orchestrated fashion to hormones and other molecules in their environment. The intracellular mechanism of insulin action remains an enigma. Although the presence of extracellular calcium was essential for insulin stimulation of amino acid uptake and DNA synthesis, the cation did not subserve a direct mediator function. Insulin promoted an increase in intracellular pH, which was mediated by the Na+/H+ antiport. Other mechanisms were probably also involved in mediating the full cellular response to insulin.

Characterisation of a cavity transfer mixer as a chemical reactor

This research project examined the feasibility of using a cavity transfer mixer (CTM) as a continuous reactor to perform reactions between either solid or liquid reagents and polymer melt; reactions which have previously been typically carried out in batch reactor systems. Equipment has been developed to allow uniform and reproducible introduction of reagents into the polymer melt. Reactions have also been performed using batch processing equipment to enable comparison with the performance of the CTM. It was concluded that: a) there are certain reactions which cannot be carried out in a CTM, but which can be performed in a batch system such as a mill or a sigma blade mixer. This was found to be the case for some neutralisation reactions where the product was quasi crosslinked. b) the reactions that can be carried out in a CTM are performed more efficiently in a CTM than on a batch process. For example, when monomers were to be grafted onto polymers, this was more safely and efficiently performed in the CTM than in a mill or a sigma blade mixer. Residence time distributions (RTDs) for three CTMs were studied in order to gain an insight into the effect of CTM geometry on RTD, polymer melt flow pattern and reactor performance. A mathematical model has been developed to predict the influence of process parameters on RTD and the results compared with experimentally observed trends. The comparison was good. A programme of research has been drawn up to form the basis of an industrially based sponsored development project of the CTM reactor. This work programme was successfully marketed to companies with commercial interest in modified rubber and plastics as an integral part of the research programme of this thesis and the sponsored research programme has paralleled the work reported here.

Learner factors leading to success on intensive language courses

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Corporate governance and the central factors influencing the roles of public and private sector board directors in the United Kingdom

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Factors affecting the adoption of new products by the sales force

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Looking under the bonnet:factors affecting student adoption of e-learning systems in Jordan

The primary questions addressed in this paper are the following: what are the factors that affect students’ adoption of an e-learning system and what are the relationships among these factors? This paper investigates and identifies some of the major factors affecting students’ adoption of an e-learning system in a university in Jordan. E-learning adoption is approached from the information systems acceptance point of view. This suggests that a prior condition for learning effectively using e-learning systems is that students must actually use them. Thus, a greater knowledge of the factors that affect IT adoption and their interrelationships is a pre-cursor to a better understanding of student acceptance of e-learning systems. In turn, this will help and guide those who develop, implement, and deliver e-learning systems. In this study, an extended version of the Technology Acceptance Model (TAM) was developed to investigate the underlying factors that influence students’ decisions to use an e-learning system. The TAM was populated using data gathered from a survey of 486 undergraduate students using the Moodle based e-learning system at the Arab Open University. The model was estimated using Structural Equation Modelling (SEM). A path model was developed to analyze the relationships between the factors to explain students’ adoption of the e-learning system. Whilst findings support existing literature about prior experience affecting perceptions, they also point to surprising group effects, which may merit future exploration.

An analysis of factors influencing the consumption of aluminum in the UK

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY SERVICES WITH PRIOR ARRANGEMENT