Fluoropolymer piezoelectrets with tubular channels: resonance behavior controlled by channel geometry

Ferro- or piezoelectrets are dielectric materials with two elastically very different macroscopic phases and electrically charged interfaces between them. One of the newer piezoelectret variants is a system of two fluoroethylenepropylene (FEP) films that are first laminated around a polytetrafluoroethylene (PTFE) template. Then, by removing the PTFE template, a two-layer FEP structure with open tubular channels is obtained. After electrical charging, the channels form easily deformable macroscopic electric dipoles whose changes under mechanical or electrical stress lead to significant direct or inverse piezoelectricity, respectively. Here, different PTFE templates are employed to generate channel geometries that vary in height or width. It is shown that the control of the channel geometry allows a direct adjustment of the resonance frequencies in the tubular-channel piezoelectrets. By combining several different channel widths in a single ferroelectret, it is possible to obtain multiple resonance peaks that may lead to a rather flat frequency-response region of the transducer material. A phenomenological relation between the resonance frequency and the geometrical parameters of a tubular channel is also presented. This relation may help to design piezoelectrets with a specific frequency response.

Prevalence of enamel defects in permanent teeth of patients with complete cleft lip and palate

Objective: To evaluate the prevalence, types, location, and characteristics of enamel defects in anterior permanent teeth of patients with complete unilateral and bilateral cleft lip and palate, as well as the relation with the cleft. Setting: Hospital for Rehabilitation of Craniofacial Anomalies, Bauru, São Paulo, Brazil. Participants: Eighty patients of both genders, 12 years and older, with unilateral or bilateral cleft lip and palate. Methods: A single examiner carried out clinical examination under artificial light with a dental probe and mirror after drying teeth according to the modified DDE index. Results: Seventy-four of 80 patients presented with at least one tooth affected by enamel defects: 165 of 325 evaluated teeth (50.8%) presented enamel defects, with hypoplasia being the most prevalent (50.7%), followed by diffuse opacity (23.1%) and demarcated opacity (18.4%). The most affected tooth was 21 (36.5%), followed by 11 (34%), located at the middle (40%) and incisal (33%) thirds. Most defects occur at the buccal surface (47.7%), followed by the distal (22.7%), the mesial (19%), and the palatal (10.6%) surfaces. A significant relationship was found between the cleft side and enamel defects. Conclusion: Upper anterior teeth of patients with complete cleft lip and palate present a high prevalence of enamel defects; the highest percentage on the cleft side suggests that the cleft does influence the occurrence of enamel defects in permanent teeth.

The future of medical diagnostics: review paper

While histopathology of excised tissue remains the gold standard for diagnosis, several new, non-invasive diagnostic techniques are being developed. They rely on physical and biochemical changes that precede and mirror malignant change within tissue. The basic principle involves simple optical techniques of tissue interrogation. Their accuracy, expressed as sensitivity and specificity, are reported in a number of studies suggests that they have a potential for cost effective, real-time, in situ diagnosis.

Avaliação da patência nasal após rinoplastia através do espelho de Glatzel

INTRODUÇÃO: O espelho de Glatzel modificado é capaz de avaliar o fluxo nasal expiratório; entretanto, há pouca informação sobre esse método e sua utilização na mensuração objetiva da patência nasal após procedimentos cirúrgicos. OBJETIVO: Comparar, através de estudo prospectivo, os resultados funcionais antes e depois de uma rinoplastia e avaliar a utilização do espelho de Glatzel como método objetivo na avaliação da patência nasal. Para esse fim, analisamos os resultados funcionais da cirurgia mediante questionário subjetivo e medidas objetivas através do espelho de Glatzel, e avaliamos a correlação entre os dois métodos. MÉTODO: Vinte pacientes (14 mulheres e 6 homens) foram submetidos à rinoplastia estética com uso de enxertos expansores. Avaliação pré e pós-operatória (90 a 120 dias) incluíram um escore de qualidade respiratória (subjetiva) e o teste do espelho de Glatzel modificado (objetiva). O teste de Spearman foi utilizado para comparar os dados subjetivos e objetivos. RESULTADOS: A avaliação subjetiva demonstrou diferença estatística (antes da cirurgia, 8 ± 2; após cirurgia, 9.4 ± 0.7; P < .001). Não houve diferença estatística nas médias da patência nasal mediante espelho de Glatzel. Não houve correlação estatisticamente significante quando comparados os valores do espelho de Glatzel com os escores referidos pelos pacientes durante avaliação subjetiva, seja no pré ou pós-operatório. CONCLUSÃO: O método de Glatzel não demonstrou significância estatística, em contraste com a avaliação subjetiva, que demonstrou melhora significativa na qualidade respiratória, sugerindo que o método de Glatzel não possui sensibilidade na detecção de pequenas mudanças anatômicas da cavidade nasal.

Experimental and numerical analysis of dry contact in the pin on disc test

The reduction of friction and wear in systems presenting metal-to-metal contacts, as in several mechanical components, represents a traditional challenge in tribology. In this context, this work presents a computational study based on the linear Archard's wear law and finite element modeling (FEM), in order to analyze unlubricated sliding wear observed in typical pin on disc tests. Such modeling was developed using finite element software Abaqus® with 3-D deformable geometries and elastic–plastic material behavior for the contact surfaces. Archard's wear model was implemented into a FORTRAN user subroutine (UMESHMOTION) in order to describe sliding wear. Modeling of debris and oxide formation mechanisms was taken into account by the use of a global wear coefficient obtained from experimental measurements. Such implementation considers an incremental computation for surface wear based on the nodal displacements by means of adaptive mesh tools that rearrange local nodal positions. In this way, the worn track was obtained and new surface profile is integrated for mass loss assessments. This work also presents experimental pin on disc tests with AISI 4140 pins on rotating AISI H13 discs with normal loads of 10, 35, 70 and 140 N, which represent, respectively, mild, transition and severe wear regimes, at sliding speed of 0.1 m/s. Numerical and experimental results were compared in terms of wear rate and friction coefficient. Furthermore, in the numerical simulation the stress field distribution and changes in the surface profile across the worn track of the disc were analyzed. The applied numerical formulation has shown to be more appropriate to predict mild wear regime than severe regime, especially due to the shorter running-in period observed in lower loads that characterizes this kind of regime.

Evolution of signal form

Visual signals, used for communication both within and between species, vary immensely in the forms that they take. How is it that all this splendour has evolved in nature? Since it is the receiver’s preferences that cause selective pressures on signals, elucidating the mechanism behind the response of the signal receiver is vital to gain a closer understanding of the evolutionary process. In my thesis I have therefore investigated how receivers, represented by chickens, Gallus gallus domesticus, respond to different stimuli displayed on a peck-sensitive computer screen. According to the receiver bias hypothesis, animals and humans often express biases when responding to certain stimuli. These biases develop as by-products of how the recognition mechanism categorises and discriminates between stimuli. Since biases are generated from general stimulus processing mechanisms, they occur irrespective of species and type of signal, and it is often possible to predict the direction and intensity of the biases. One of the results from the experiments in my thesis demonstrates that similar experience in different species may generate similar biases. By giving chickens at least some of the experience of human faces as humans presumably have, the chickens subsequently expressed preferences for the same faces as a group of human subjects. Another kind of experience generated a bias for symmetry. This bias developed in the context of training chickens to recognise two mirror images of an asymmetrical stimulus. Untrained chickens and chickens trained on only one of the mirror images expressed no symmetry preferences. The bias produced by the training regime was for a specific symmetrical stimulus which had a strong resemblance to the familiar asymmetrical exemplar, rather than a general preference for symmetry. A further kind of experience, training chickens to respond to some stimuli but not to others, generated a receiver bias for exaggerated stimuli, whereas chickens trained on reversed stimuli developed a bias for less exaggerated stimuli. To investigate the potential of this bias to drive the evolution of signals towards exaggerated forms, a simplified evolutionary process was mimicked. The stimuli variants rejected by the chickens were eliminated, whereas the selected forms were kept and evolved prior to the subsequent display. As a result, signals evolved into exaggerated forms in all tested stimulus dimensions: length, intensity and area, despite the inclusion of a cost to the sender for using increasingly exaggerated signals. The bias was especially strong and persistent for stimuli varying along the intensity dimension where it remained despite extensive training. All the results in my thesis may be predicted by the receiver bias hypothesis. This implies that biases, developed due to stimuli experience, may be significant mechanisms driving the evolution of signal form.

Ni una más. International cooperation against gender-based discrimination: the femicide case in Ciudad Juárez, Chihuahua, Mexico

The femicide in Ciudad Juárez is a story made of extreme violence against women for different reasons, by different actors, under different circumstances, and following different behavioural patterns. All within a gender discrimination frame based on the idea that women are inferior, interchangeable and disposable according to the patriarchal hierarchy still present in Mexico, but strongly reinforced by a sort of conspiracy of silence provoked either by the high impunity rate, the governmental incompetence to solve the crimes, or the general indifference of the population. It is the story of hundreds of kidnapped, raped, in many cases tortured, and murdered young women in the border between Mexico and the United States. The murders first came into light in 1993 and up to now young women continue to “disappear” without any hope of bringing the perpetrators to justice, stopping impunity, convicting the assassins, and bringing justice to the families of the deceased girls and women. The main questions about femicide in Ciudad Juárez seem to be: why were they brutally assassinated?, why most of the crimes have not been solved yet?, why and how is Ciudad Juárez different from other border cities with the same characteristics?, which powers are behind those crimes in a city that implies mainly women as its labor force, and which has the lowest unemployment rate in the whole country? But there are also many other questions dealing more with the context, the Juarences’ lifestyles, the eventual hidden powers behind the crimes, the possible murderers’ reasons, the response of the local civil society, or the international community actions to fight against femicide there, among many other things, that are still waiting for an answer and that this paper will ‘narrate’ in order to provide a holistic panorama for the readers. But above all there is the need to remember that every single woman or girl assassinated there had a name, an identity, a family, a story to be told time after time and as many times as necessary, in order to avoid accepting these crimes just as statistics, as cold numbers that might make us forget the human tragedy that has been flagellating the city since 1993. We must remember as well that their deaths express gender oppression, the inequality of the relations between what is male and what is female, a manifestation of domination, terror, social extermination, patriarchal hegemony, social class and impunity. The city is the perfect mirror where all the contradictions of globalization get reflected. It is there where all the globalization evils are present and survive by sucking their women’s blood. It is a city where some concepts such as gender, migration and power are closely related with a negative connotation.

Reconstruction from image correspondences

A single picture provides a largely incomplete representation of the scene one is looking at. Usually it reproduces only a limited spatial portion of the scene according to the standpoint and the viewing angle, besides it contains only instantaneous information. Thus very little can be understood on the geometrical structure of the scene, the position and orientation of the observer with respect to it remaining also hard to guess. When multiple views, taken from different positions in space and time, observe the same scene, then a much deeper knowledge is potentially achievable. Understanding inter-views relations enables construction of a collective representation by fusing the information contained in every single image. Visual reconstruction methods confront with the formidable, and still unanswered, challenge of delivering a comprehensive representation of structure, motion and appearance of a scene from visual information. Multi-view visual reconstruction deals with the inference of relations among multiple views and the exploitation of revealed connections to attain the best possible representation. This thesis investigates novel methods and applications in the field of visual reconstruction from multiple views. Three main threads of research have been pursued: dense geometric reconstruction, camera pose reconstruction, sparse geometric reconstruction of deformable surfaces. Dense geometric reconstruction aims at delivering the appearance of a scene at every single point. The construction of a large panoramic image from a set of traditional pictures has been extensively studied in the context of image mosaicing techniques. An original algorithm for sequential registration suitable for real-time applications has been conceived. The integration of the algorithm into a visual surveillance system has lead to robust and efficient motion detection with Pan-Tilt-Zoom cameras. Moreover, an evaluation methodology for quantitatively assessing and comparing image mosaicing algorithms has been devised and made available to the community. Camera pose reconstruction deals with the recovery of the camera trajectory across an image sequence. A novel mosaic-based pose reconstruction algorithm has been conceived that exploit image-mosaics and traditional pose estimation algorithms to deliver more accurate estimates. An innovative markerless vision-based human-machine interface has also been proposed, so as to allow a user to interact with a gaming applications by moving a hand held consumer grade camera in unstructured environments. Finally, sparse geometric reconstruction refers to the computation of the coarse geometry of an object at few preset points. In this thesis, an innovative shape reconstruction algorithm for deformable objects has been designed. A cooperation with the Solar Impulse project allowed to deploy the algorithm in a very challenging real-world scenario, i.e. the accurate measurements of airplane wings deformations.

La costruzione razionale della casa. Scritti e progetti di Giuseppe Pagano

The rational construction of the house. The writings and projects of Giuseppe Pagano Description, themes and research objectives The research aims at analysing the architecture of Giuseppe Pagano, which focuses on the theme of dwelling, through the reading of 3 of his house projects. On the one hand, these projects represent “minor” works not thoroughly known by Pagano’s contemporary critics; on the other they emphasise a particular methodological approach, which serves the author to explore a theme closely linked to his theoretical thought. The house project is a key to Pagano’s research, given its ties to the socio-cultural and political conditions in which the architect was working, so that it becomes a mirror of one of his specific and theoretical path, always in a state of becoming. Pagano understands architecture as a “servant of the human being”, subject to a “utilitarian slavery” since it is a clear, essential and “modest” answer to specific human needs, free from aprioristic aesthetic and formal choices. It is a rational architecture in sensu stricto; it constitutes a perfect synthesis between cause and effect and between function and form. The house needs to accommodate these principles because it is closely intertwined with human needs and intimately linked to a specific place, climatic conditions and technical and economical possibilities. Besides, differently from his public and common masterpieces such as the Palazzo Gualino, the Istituto di Fisica and the Università Commerciale Bocconi, the house projects are representative of a precise project will, which is expressed in a more authentic way, partially freed from political influences and dogmatic preoccupations and, therefore, far from the attempt to research a specific expressive language. I believe that the house project better represents that “ingenuity”, freshness and “sincerity” that Pagano identifies with the minor architecture, thereby revealing a more authentic expression of his understanding of a project. Therefore, the thesis, by tracing the theoretical research of Pagano through the analysis of some of his designed and built works, attempts to identify a specific methodological approach to Pagano’s project, which, developed through time, achieves a certain clarity in the 1930s. In fact, this methodological approach becomes more evident in his last projects, mainly regarding the house and the urban space. These reflect the attempt to respond to the new social needs and, at the same time, they also are an expression of a freer idea of built architecture, closely linked with the place and with the human being who dwells it. The three chosen projects (Villa Colli, La Casa a struttura d’acciaio and Villa Caraccio) make Pagano facing different places, different customers and different economic and technical conditions, which, given the author’s biography, correspond to important historical and political conditions. This is the reason why the projects become apparently distant works, both linguistically and conceptually, to the point that one can define them as ”eclectic”. However, I argue that this eclecticism is actually an added value to the architectural work of Pagano, steaming from the use of a method which, having as a basis the postulate of a rational architecture as essence and logic of building, finds specific variations depending on the multiple variables to be addressed by the project. This is the methodological heritage that Pagano learns from the tradition, especially that of the rural residential architecture, defined by Pagano as a “dictionary of the building logic of man”, as an “a-stylistic background”. For Pagano this traditional architecture is a clear expression of the relationships between a theme and its development, an architectural “fact” that is resolved with purely technical and utilitarian aims and with a spontaneous development far from any aprioristic theoretical principle. Architecture, therefore, cannot be an invention for Pagano and the personal contribution of each architect has to consider his/her close relationship with the specific historical context, place and new building methods. These are basic principles in the methodological approach that drives a great deal of his research and that also permits his thought to be modern. I argue that both ongoing and new collaborations with younger protagonists of the culture and architecture of the period are significant for the development of his methodology. These encounters represent the will to spread his own understanding of the “new architecture” as well as a way of self-renewal by confronting the self with new themes and realities and by learning from his collaborators. Thesis’ outline The thesis is divided in two principal parts, each articulated in four chapters attempting to offer a new reading of the theory and work of Pagano by emphasising the central themes of the research. The first chapter is an introduction to the thesis and to the theme of the rational house, as understood and developed in its typological and technical aspects by Pagano and by other protagonists of the Italian rationalism of the 1930s. Here the attention is on two different aspects defining, according to Pagano, the house project: on the one hand, the typological renewal, aimed at defining a “standard form” as a clear and essential answer to certain needs and variables of the project leading to different formal expressions. On the other, it focuses on the building, understood as a technique to “produce” architecture, where new technologies and new materials are not merely tools but also essential elements of the architectural work. In this way the villa becomes different from the theme of the common house or from that of the minimalist house, by using rules in the choice of material and in the techniques that are every time different depending on the theme under exploration and on the contingency of place. It is also visible the rigorous rationalism that distinguishes the author's appropriation of certain themes of rural architecture. The pages of “Casabella” and the events of the contemporary Triennali form the preliminary material for the writing of this chapter given that they are primary sources to individuate projects and writings produced by Pagano and contemporary architects on this theme. These writings and projects, when compared, reconstruct the evolution of the idea of the rational house and, specifically, of the personal research of Pagano. The second part regards the reading of three of Pagano’s projects of houses as a built verification of his theories. This section constitutes the central part of the thesis since it is aimed at detecting a specific methodological approach showing a theoretical and ideological evolution expressed in the vast edited literature. The three projects that have been chosen explore the theme of the house, looking at various research themes that the author proposes and that find continuity in the affirmation of a specific rationalism, focussed on concepts such as essentiality, utility, functionality and building honesty. These concepts guide the thought and the activities of Pagano, also reflecting a social and cultural period. The projects span from the theme of the villa moderna, Villa Colli, which, inspired by the architecture of North Europe, anticipates a specific rationalism of Pagano based on rigour, simplicity and essentiality, to the theme of the common house, Casa a struttura d’acciaio, la casa del domani, which ponders on the definition of new living spaces and, moreover, on new concepts of standardisation, economical efficiency and new materials responding to the changing needs of the modern society. Finally, the third project returns to the theme of the, Villa Caraccio, revisiting it with new perspectives. These perspectives find in the solution of the open plant, in the openness to nature and landscape and in the revisiting of materials and local building systems that idea of the freed house, which express clearly a new theoretical thought. Methodology It needs to be noted that due to the lack of an official Archive of Pagano’s work, the analysis of his work has been difficult and this explains the necessity to read the articles and the drawings published in the pages of «Casabella» and «Domus». As for the projects of Villa Colli and Casa a struttura d’acciaio, parts of the original drawings have been consulted. These drawings are not published and are kept in private archives of the collaborators of Pagano. The consultation of these documents has permitted the analysis of the cited works, which have been subject to a more complete reading following the different proposed solutions, which have permitted to understand the project path. The projects are analysed thought the method of comparison and critical reading which, specifically, means graphical elaborations and analytical schemes, mostly reconstructed on the basis of original projects but, where possible, also on a photographic investigation. The focus is on the project theme which, beginning with a specific living (dwelling) typology, finds variations because of the historico-political context in which Pagano is embedded and which partially shapes his research and theoretical thought, then translated in the built work. The analysis of the work follows, beginning, where possible, from a reconstruction of the evolution of the project as elaborated on the basis of the original documents and ending on an analysis of the constructive principles and composition. This second phase employs a methodology proposed by Pagano in his article Piante di ville, which, as expected, focuses on the plant as essential tool to identify the “true practical and poetic qualities of the construction”(Pagano, «Costruzioni-Casabella», 1940, p. 2). The reading of the project is integrated with the constructive analyses related to the technical aspects of the house which, in the case of Casa a struttura d’acciaio, play an important role in the project, while in Villa Colli and in Villa Caraccio are principally linked to the choice of materials for the construction of the different architectural elements. These are nonetheless key factors in the composition of the work. Future work could extend this reading to other house projects to deepen the research that could be completed with the consultation of Archival materials, which are missing at present. Finally, in the appendix I present a critical selection of the Pagano’s writings, which recall the themes discussed and embodied by the three projects. The texts have been selected among the articles published in Casabella and in other journals, completing the reading of the project work which cannot be detached from his theoretical thought. Moving from theory to project, we follow a path that brings us to define and deepen the central theme of the thesis: rational building as the principal feature of the architectural research of Pagano, which is paraphrased in multiple ways in his designed and built works.

Untersuchungen zur Visuomotorik des Menschen

Motorische Bewegungen werden über die visuelle Rückmeldung auf ihre Genauigkeit kontrolliert und ggf. korrigiert. Über einen technischen Eingriff, wie beispielsweise einer Prismenbrille, kann man eine Differenz zwischen optisch wahrgenommener und haptisch erlebter Umwelt erzeugen, um die Fähigkeiten des visuomotorischen Systems zu testen. In dieser Arbeit wurde eine computergestützte Methode entwickelt, eine solche visuomotorische Differenz zu simulieren. Die Versuchspersonen führen eine ballistische Bewegung mit Arm und Hand aus in der Absicht, ein vorgegebenes Ziel zu treffen. Die Trefferpunkte werden durch einen Computer mit Hilfe eines Digitalisierungstablettes aufgenommen. Die visuelle Umwelt, welche den Versuchspersonen präsentiert wird, ist auf einem Monitor dargestellt. Das Monitorabbild – ein Kreuz auf weißem Hintergrund – betrachten die Testpersonen über einen Spiegel. Dieser ist in einem entsprechenden Winkel zwischen Monitor und Digitalisierungstablett angebracht, so dass das Zielbild auf dem Digitalisierungstablett projiziert wird. Die Testpersonen nehmen das Zielkreuz auf dem Digitalisierungstablett liegend wahr. Führt die Versuchsperson eine Zielbewegung aus, können die aufgenommenen Koordinaten als Punkte auf dem Monitor dargestellt werden und die Testperson erhält über diese Punktanzeige ein visuelles Feedback ihrer Bewegung. Der Arbeitsbereich des Digitalisierungstabletts kann über den Computer eingerichtet und so motorische Verschiebungen simuliert werden. Die verschiedenartigen Möglichkeiten dieses Aufbaus wurden zum Teil in Vorversuchen getestet um Fragestellungen, Methodik und technische Einrichtungen aufeinander abzustimmen. Den Hauptversuchen galt besonderes Interesse an der zeitlichen Verzögerung des visuellen Feedbacks sowie dem intermanuellen Transfer. Hierbei ergaben sich folgende Ergebnisse: ● Die Versuchspersonen adaptieren an eine räumlich verschobene Umwelt. Der Adaptationsverlauf lässt sich mit einer Exponentialfunktion mathematisch berechnen und darstellen. ● Dieser Verlauf ist unabhängig von der Art des visuellen Feedbacks. Die Beobachtung der Handbewegung während der Adaptation zeigt die gleiche Zielabfolge wie eine einfache Punktprojektion, die den Trefferort der Bewegung darstellt. ● Der exponentielle Verlauf der Adaptationsbewegung ist unabhängig von den getesteten zeitlichen Verzögerungen des visuellen Feedbacks. ● Die Ergebnisse des Folgeeffektes zeigen, dass bei zunehmender zeitlicher Verzögerung des visuellen Feedbacks während der Adaptationsphase, die Größe des Folgeeffektwertes geringer wird, d.h. die anhaltende Anpassungsleistung an eine visuomotorische Differenz sinkt. ● Die Folgeeffekte weisen individuelle Eigenheiten auf. Die Testpersonen adaptieren verschieden stark an eine simulierte Verschiebung. Ein Vergleich mit den visuomotorischen Herausforderungen im Vorleben der Versuchspersonen ließ vermuten, dass das visuomotorische System des Menschen trainierbar ist und sich - je nach Trainingszustand – unterschiedlich an wahrgenommene Differenzen anpasst. ● Der intermanuelle Transfer konnte unter verschiedenen Bedingungen nachgewiesen werden. ● Ein deutlich stärkerer Folgeeffekt kann beobachtet werden, wenn die wahrgenommene visuomotorische Differenz zwischen Ziel und Trefferpunkt in eine Gehirnhälfte projiziert wird und der Folgeeffekt mit der Hand erfolgt, welche von dieser Hirnhemisphäre gesteuert wird. Der intermanuelle Transfer wird demnach begünstigt, wenn die visuelle Projektion der Fehlerbeobachtung in die Gehirnhälfte erfolgt, die während der Adaptationsphase motorisch passiv ist.

Grazing incidence pumped Zr x-ray laser for spectroscopy on Li-like ions

X-ray laser fluorescence spectroscopy of the 2s-2p transition in Li-like ions is promising to become a widely applicable tool to provide information on the nuclear charge radii of stable and radioactive isotopes. For performing such experiments at the Experimental Storage Ring ESR, and the future NESR within the FAIR Project, a grazing incidence pumped (GRIP) x-ray laser (XRL) was set up at GSI Darmstadt using PHELIX (Petawatt High Energy Laser for heavy Ions eXperiments). The experiments demonstrated that lasing using the GRIP geometry could be achieved with relatively low pump energy, a prerequisite for higher repetition rate. In the first chapter the need of a plasma XRL is motivated and a short history of the plasma XRL is presented. The distinctive characteristic of the GRIP method is the controlled deposition of the pump laser energy into the desired plasma density region. While up to now the analysis performed were mostly concerned with the plasma density at the turning point of the main pump pulse, in this thesis it is demonstrated that also the energy deposition is significantly modified for the GRIP method, being sensitive in different ways to a large number of parameters. In the second chapter, the theoretical description of the plasma evolution, active medium and XRL emission properties are reviewed. In addition an innovative analysis of the laser absorption in plasma which includes an inverse Bremsstrahlung (IB) correction factor is presented. The third chapter gives an overview of the experimental set-up and diagnostics, providing an analytical formula for the average and instantaneous traveling wave speed generated with a tilted, on-axis spherical mirror, the only focusing system used up to now in GRIP XRL. The fourth chapter describes the experimental optimization and results. The emphasis is on the effect of the incidence angle of the main pump pulse on the absorption in plasma and on output and gain in different lasing lines. This is compared to the theoretical results for two different incidence angles. Significant corrections for the temperature evolution during the main pump pulse due to the incidence angle are demonstrated in comparison to a simple analytical model which does not take into account the pumping geometry. A much better agreement is reached by the model developed in this thesis. An interesting result is also the appearance of a central dip in the spatially resolved keV emission which was observed in the XRL experiments for the first time and correlates well with previous near field imaging and plasma density profile measurements. In the conclusion also an outlook to the generation of shorter wavelength XRL’s is given.

Polymer properties measured by micromechanical cantilever technique

Surface stress changes induced by specific adsorption of molecules were investigated using a micromechanical cantilever sensor (MCS) device. 16 MCS are grouped within four separate wells. Each well can be addressed independently by different liquid enabling functionalization of MCS separately by flowing different solutions through each well and performing sensing and reference experiments simultaneously. In addition, each well contains a fixed reference mirror, which allows measuring the absolute bending of MCS. The effect of the flow rate on the MCS bending change was found to be dependent on the absolute bending value of MCS. In addition, the signal from the reference mirror can be used to follow refractive index changes upon mixing different solutions. Finite element simulation of solution exchange in wells was compared with experiment results. Both revealed that one solution can be exchanged by another one after a total volume of 200 µl has flown through. Using MCS, the adsorption of thiolated deoxyribonucleic acid (DNA) molecules and 6-mercapto-1-hexanol (MCH) on gold surfaces, and the DNA hybridization were performed. The nanomechanical response is in agreement with data reported by Fritz et al.1 Thus, the multiwell device is readily applicable for sensing of multiple chemical and biological recognition events in a single step. In this context controlled release and uptake of drugs are currently widely discussed. As a model system, we have used polystyrene (PS) spheres with diameters in the order of µm. The swelling behavior of individual PS spheres in toluene vapor was studied via mass loading by means of micromechanical cantilever sensors. For 4–8% cross-linked PS a mass increase of 180% in saturated toluene vapor was measured. In addition, the diameter change in saturated toluene vapor was measured and the corresponding volume increase of 200% was calculated. The mass of the swollen PS sphere decreases with increasing exposure time to ultraviolet (UV) light. The swelling response is significantly different between the first and the second exposure to toluene vapor. This is attributed to the formation of a cross-linked shell at the surface of the PS spheres. Shape persistent parts were observed for locally UV irradiated PS spheres. These PS spheres were found to be fluorescent and cracks occur after exposure in toluene liquid. The diffusion time of dye molecules in PS spheres increases with increasing chemical cross-linking density. This concept of locally dissolving non cross-linked PS from the sphere was applied to fabricate donut structures on surfaces. Arrays of PS spheres were fabricated using spin coating. The donut structure was produced simply after liquid solvent rinsing. The complete cross-linking of PS spheres was found after long exposure time to UV. We found that stabilizers play a major role in the formation of the donut nanostructures.

Topological aspects of the human protein interaction network

It is currently widely accepted that the understanding of complex cell functions depends on an integrated network theoretical approach and not on an isolated view of the different molecular agents. Aim of this thesis was the examination of topological properties that mirror known biological aspects by depicting the human protein network with methods from graph- and network theory. The presented network is a partial human interactome of 9222 proteins and 36324 interactions, consisting of single interactions reliably extracted from peer-reviewed scientific publications. In general, one can focus on intra- or intermodular characteristics, where a functional module is defined as "a discrete entity whose function is separable from those of other modules". It is found that the presented human network is also scale-free and hierarchically organised, as shown for yeast networks before. The interactome also exhibits proteins with high betweenness and low connectivity which are biologically analyzed and interpreted here as shuttling proteins between organelles (e.g. ER to Golgi, internal ER protein translocation, peroxisomal import, nuclear pores import/export) for the first time. As an optimisation for finding proteins that connect modules, a new method is developed here based on proteins located between highly clustered regions, rather than regarding highly connected regions. As a proof of principle, the Mediator complex is found in first place, the prime example for a connector complex. Focusing on intramodular aspects, the measurement of k-clique communities discriminates overlapping modules very well. Twenty of the largest identified modules are analysed in detail and annotated to known biological structures (e.g. proteasome, the NFκB-, TGF-β complex). Additionally, two large and highly interconnected modules for signal transducer and transcription factor proteins are revealed, separated by known shuttling proteins. These proteins yield also the highest number of redundant shortcuts (by calculating the skeleton), exhibit the highest numbers of interactions and might constitute highly interconnected but spatially separated rich-clubs either for signal transduction or for transcription factors. This design principle allows manifold regulatory events for signal transduction and enables a high diversity of transcription events in the nucleus by a limited set of proteins. Altogether, biological aspects are mirrored by pure topological features, leading to a new view and to new methods that assist the annotation of proteins to biological functions, structures and subcellular localisations. As the human protein network is one of the most complex networks at all, these results will be fruitful for other fields of network theory and will help understanding complex network functions in general.

Fluid-structure interaction by a coupled lattice Boltzmann-finite element approach

In this thesis, a strategy to model the behavior of fluids and their interaction with deformable bodies is proposed. The fluid domain is modeled by using the lattice Boltzmann method, thus analyzing the fluid dynamics by a mesoscopic point of view. It has been proved that the solution provided by this method is equivalent to solve the Navier-Stokes equations for an incompressible flow with a second-order accuracy. Slender elastic structures idealized through beam finite elements are used. Large displacements are accounted for by using the corotational formulation. Structural dynamics is computed by using the Time Discontinuous Galerkin method. Therefore, two different solution procedures are used, one for the fluid domain and the other for the structural part, respectively. These two solvers need to communicate and to transfer each other several information, i.e. stresses, velocities, displacements. In order to guarantee a continuous, effective, and mutual exchange of information, a coupling strategy, consisting of three different algorithms, has been developed and numerically tested. In particular, the effectiveness of the three algorithms is shown in terms of interface energy artificially produced by the approximate fulfilling of compatibility and equilibrium conditions at the fluid-structure interface. The proposed coupled approach is used in order to solve different fluid-structure interaction problems, i.e. cantilever beams immersed in a viscous fluid, the impact of the hull of the ship on the marine free-surface, blood flow in a deformable vessels, and even flapping wings simulating the take-off of a butterfly. The good results achieved in each application highlight the effectiveness of the proposed methodology and of the C++ developed software to successfully approach several two-dimensional fluid-structure interaction problems.

Travi in parete sottile con deformabilità a taglio e distorsione di sezione: formulazione teorica, modellazione numerica e applicazioni

Il presente lavoro di tesi ha riguardato una riformulazione teorica, una modellazione numerica e una serie di applicazioni della Generalized Beam Theory per lo studio dei profili in parete sottile con particolare riguardo ai profili in acciaio formati a freddo. In particolare, in questo lavoro è proposta una riscrittura della cinematica GBT che introduce in una forma originale la deformabilità a taglio della sezione. Tale formulazione consente di conservare il formato della GBT classica e introducendo uno spostamento di warping variabile lungo lo spessore della generica parete della sezione trasversale, garantisce perfetta coerenza tra la componente flessionale e tagliante della trave. E' mostrato, come tale riscrittura consente in maniera agevole di ricondursi alle teorie classiche di trave, anche deformabili a taglio. Inoltre, in tale contesto, è stata messa a punto una procedura di ricostruzione dello sforzo tridimensionale in grado ricostruire la parte reattiva delle componenti di tensioni dovuta al vincolamento interno proprio di un modello a cinematica ridotta. Sulla base di tali strumenti, è stato quindi proposto un approccio progettuale dedicato ai profili in classe 4, definito ESA (Embedded Stability Analysis), in grado di svolgere le verifiche coerentemente con quanto prescritto dalle normative vigenti. Viene infine presentata una procedura numerica per la progettazione di sistemi di copertura formati a freddo. Tale procedura permette di effettuare in pochi semplici passi il progetto dell'arcareccio e dei dettagli costruttivi relativi alla copertura.