A radial basis function network (RBFN) for function approximation

A radial basis function network (RBFN) circuit for function approximation is presented. Simulation and experimental results show that the network has good approximation capabilities. The RBFN was a squared hyperbolic secant with three adjustable parameters amplitude, width and center. To test the network a sinusoidal and sine function,vas approximated.

An analog implementation of radial basis function network appropriate for transducer linearizer

A circuit for transducer linearizer tasks have been designed and built using discrete components and it implements by: a Radial Basis Function Network (RBFN) with three basis functions. The application in a linearized thermistor showed that the network has good approximation capabilities. The circuit advantages is the amplitude, width and center.

Co-simulation tools for networked control systems: revision and utilization

Networked control systems (NCSs) are distributed control systems in which the sensors, actuators, and controllers are physically separated and connected through an industrial network. The main challenge related to the development of NCSs is the degenerative effects caused by the inclusion of this communication network in the closed loop control. In order to mitigate these effects, co-simulation tools for NCS have been developed to study the network influence in the NCS. This paper presents a revision about co-simulation tools for NCS and the application of two of these tools for the design and evaluation of NCSs. The TrueTime and Jitterbug tools were used together to evaluate the main configuration parameter that affects the performance of CAN-based NCS and to verify the NCS quality of control under various timing conditions including different transmission period of messages and network delays. Therefore, the simulation results led to the conclusion that despite the transmission period of messages is the most significant factor among the analyzed in the design of NCS, its influence is related to the kind of system with greater effects in NCSs with fast dynamics.

Phenol biodegradation by a microbial consortium: application of artificial neural network (ANN) modelling

In this study, an effective microbial consortium for the biodegradation of phenol was grown under different operational conditions, and the effects of phosphate concentration (1.4 g L-1, 2.8 g L-1, 4.2 g L-1), temperature (25 degrees C, 30 degrees C, 35 degrees C), agitation (150 rpm, 200 rpm, 250 rpm) and pH (6, 7, 8) on phenol degradation were investigated, whereupon an artificial neural network (ANN) model was developed in order to predict degradation. The learning, recall and generalization characteristics of neural networks were studied using data from the phenol degradation system. The efficiency of the model generated by the ANN was then tested and compared with the experimental results obtained. In both cases, the results corroborate the idea that aeration and temperature are crucial to increasing the efficiency of biodegradation.

A decaying factor accounts for contained activity in neuronal networks with no need of hierarchical or modular organization

The mechanisms responsible for containing activity in systems represented by networks are crucial in various phenomena, for example, in diseases such as epilepsy that affect the neuronal networks and for information dissemination in social networks. The first models to account for contained activity included triggering and inhibition processes, but they cannot be applied to social networks where inhibition is clearly absent. A recent model showed that contained activity can be achieved with no need of inhibition processes provided that the network is subdivided into modules (communities). In this paper, we introduce a new concept inspired in the Hebbian theory, through which containment of activity is achieved by incorporating a dynamics based on a decaying activity in a random walk mechanism preferential to the node activity. Upon selecting the decay coefficient within a proper range, we observed sustained activity in all the networks tested, namely, random, Barabasi-Albert and geographical networks. The generality of this finding was confirmed by showing that modularity is no longer needed if the dynamics based on the integrate-and-fire dynamics incorporated the decay factor. Taken together, these results provide a proof of principle that persistent, restrained network activation might occur in the absence of any particular topological structure. This may be the reason why neuronal activity does not spread out to the entire neuronal network, even when no special topological organization exists.

Models of passive and active dendrite motoneuron pools and their differences in muscle force control

Motoneuron (MN) dendrites may be changed from a passive to an active state by increasing the levels of spinal cord neuromodulators, which activate persistent inward currents (PICs). These exert a powerful influence on MN behavior and modify the motor control both in normal and pathological conditions. Motoneuronal PICs are believed to induce nonlinear phenomena such as the genesis of extra torque and torque hysteresis in response to percutaneous electrical stimulation or tendon vibration in humans. An existing large-scale neuromuscular simulator was expanded to include MN models that have a capability to change their dynamic behaviors depending on the neuromodulation level. The simulation results indicated that the variability (standard deviation) of a maintained force depended on the level of neuromodulatory activity. A force with lower variability was obtained when the motoneuronal network was under a strong influence of PICs, suggesting a functional role in postural and precision tasks. In an additional set of simulations when PICs were active in the dendrites of the MN models, the results successfully reproduced experimental results reported from humans. Extra torque was evoked by the self-sustained discharge of spinal MNs, whereas differences in recruitment and de-recruitment levels of the MNs were the main reason behind torque and electromyogram (EMG) hysteresis. Finally, simulations were also used to study the influence of inhibitory inputs on a MN pool that was under the effect of PICs. The results showed that inhibition was of great importance in the production of a phasic force, requiring a reduced co-contraction of agonist and antagonist muscles. These results show the richness of functionally relevant behaviors that can arise from a MN pool under the action of PICs.

Modelizzazione spazio-temporale delle dinamiche di uso del suolo ed analisi comparativa di differenti approcci predittivi. Uso integrato di SIG e telerilevamento nello studio dei processi di deforestazione nella regione La Joyanca in Peten, Guatemala

L’uso frequente dei modelli predittivi per l’analisi di sistemi complessi, naturali o artificiali, sta cambiando il tradizionale approccio alle problematiche ambientali e di rischio. Il continuo miglioramento delle capacità di elaborazione dei computer facilita l’utilizzo e la risoluzione di metodi numerici basati su una discretizzazione spazio-temporale che permette una modellizzazione predittiva di sistemi reali complessi, riproducendo l’evoluzione dei loro patterns spaziali ed calcolando il grado di precisione della simulazione. In questa tesi presentiamo una applicazione di differenti metodi predittivi (Geomatico, Reti Neurali, Land Cover Modeler e Dinamica EGO) in un’area test del Petén, Guatemala. Durante gli ultimi decenni questa regione, inclusa nella Riserva di Biosfera Maya, ha conosciuto una rapida crescita demografica ed un’incontrollata pressione sulle sue risorse naturali. L’area test puó essere suddivisa in sotto-regioni caratterizzate da differenti dinamiche di uso del suolo. Comprendere e quantificare queste differenze permette una migliore approssimazione del sistema reale; é inoltre necessario integrare tutti i parametri fisici e socio-economici, per una rappresentazione più completa della complessità dell’impatto antropico. Data l’assenza di informazioni dettagliate sull’area di studio, quasi tutti i dati sono stati ricavati dall’elaborazione di 11 immagini ETM+, TM e SPOT; abbiamo poi realizzato un’analisi multitemporale dei cambi uso del suolo passati e costruito l’input per alimentare i modelli predittivi. I dati del 1998 e 2000 sono stati usati per la fase di calibrazione per simulare i cambiamenti nella copertura terrestre del 2003, scelta come data di riferimento per la validazione dei risultati. Quest’ultima permette di evidenziare le qualità ed i limiti per ogni modello nelle differenti sub-regioni.

Statistical methods for biomedical signal analysis and processing

Statistical modelling and statistical learning theory are two powerful analytical frameworks for analyzing signals and developing efficient processing and classification algorithms. In this thesis, these frameworks are applied for modelling and processing biomedical signals in two different contexts: ultrasound medical imaging systems and primate neural activity analysis and modelling. In the context of ultrasound medical imaging, two main applications are explored: deconvolution of signals measured from a ultrasonic transducer and automatic image segmentation and classification of prostate ultrasound scans. In the former application a stochastic model of the radio frequency signal measured from a ultrasonic transducer is derived. This model is then employed for developing in a statistical framework a regularized deconvolution procedure, for enhancing signal resolution. In the latter application, different statistical models are used to characterize images of prostate tissues, extracting different features. These features are then uses to segment the images in region of interests by means of an automatic procedure based on a statistical model of the extracted features. Finally, machine learning techniques are used for automatic classification of the different region of interests. In the context of neural activity signals, an example of bio-inspired dynamical network was developed to help in studies of motor-related processes in the brain of primate monkeys. The presented model aims to mimic the abstract functionality of a cell population in 7a parietal region of primate monkeys, during the execution of learned behavioural tasks.

Fault detection, diagnosis and active fault tolerant control for a satellite attitude control system

Modern control systems are becoming more and more complex and control algorithms more and more sophisticated. Consequently, Fault Detection and Diagnosis (FDD) and Fault Tolerant Control (FTC) have gained central importance over the past decades, due to the increasing requirements of availability, cost efficiency, reliability and operating safety. This thesis deals with the FDD and FTC problems in a spacecraft Attitude Determination and Control System (ADCS). Firstly, the detailed nonlinear models of the spacecraft attitude dynamics and kinematics are described, along with the dynamic models of the actuators and main external disturbance sources. The considered ADCS is composed of an array of four redundant reaction wheels. A set of sensors provides satellite angular velocity, attitude and flywheel spin rate information. Then, general overviews of the Fault Detection and Isolation (FDI), Fault Estimation (FE) and Fault Tolerant Control (FTC) problems are presented, and the design and implementation of a novel diagnosis system is described. The system consists of a FDI module composed of properly organized model-based residual filters, exploiting the available input and output information for the detection and localization of an occurred fault. A proper fault mapping procedure and the nonlinear geometric approach are exploited to design residual filters explicitly decoupled from the external aerodynamic disturbance and sensitive to specific sets of faults. The subsequent use of suitable adaptive FE algorithms, based on the exploitation of radial basis function neural networks, allows to obtain accurate fault estimations. Finally, this estimation is actively exploited in a FTC scheme to achieve a suitable fault accommodation and guarantee the desired control performances. A standard sliding mode controller is implemented for attitude stabilization and control. Several simulation results are given to highlight the performances of the overall designed system in case of different types of faults affecting the ADCS actuators and sensors.

Simulationen zur Exzitonendiffusion in organischen Halbleitern

Die vorliegende Dissertation dient dazu, das Verständnis des Exzitonentransports in organischen Halbleitern, wie sie in Leuchtdioden oder Solarzellen eingesetzt werden, zu vertiefen. Mithilfe von Computersimulationen wurde der Transport von Exzitonen in amorphen und kristallinen organischen Materialien beschrieben, angefangen auf mikroskopischer Ebene, auf der quantenmechanische Prozesse ablaufen, bis hin zur makroskopischen Ebene, auf welcher physikalisch bestimmbare Größen wie der Diffusionskoeffizient extrahierbar werden. Die Modellbildung basiert auf dem inkohärenten elektronischen Energietransfer. In diesem Rahmen wird der Transport des Exzitons als Hüpfprozess aufgefasst, welcher mit kinetischen Monte-Carlo Methoden simuliert wurde. Die notwendigen quantenmechanischen Übergangsraten zwischen den Molekülen wurden anhand der molekularen Struktur fester Phasen berechnet. Die Übergangsraten lassen sich in ein elektronisches Kopplungselement und die Franck-Condon-gewichtete Zustandsdichte aufteilen. Der Fokus dieser Arbeit lag einerseits darauf die Methoden zu evaluieren, die zur Berechnung der Übergangsraten in Frage kommen und andererseits den Hüpftransport zu simulieren und eine atomistische Interpretation der makroskopischen Transporteigenschaften der Exzitonen zu liefern. rnrnVon den drei untersuchten organischen Systemen, diente Aluminium-tris-(8-hydroxychinolin) der umfassenden Prüfung des Verfahrens. Es wurde gezeigt, dass stark vereinfachte Modelle wie die Marcus-Theorie die Übergangsraten und damit das Transportverhalten der Exzitonen oftmals qualitativ korrekt wiedergeben. Die meist deutlich größeren Diffusionskonstanten von Singulett- im Vergleich zu Triplett-Exzitonen haben ihren Ursprung in der längeren Reichweite der Kopplungselemente der Singulett-Exzitonen, wodurch ein stärker verzweigtes Netzwerk gebildet wird. Der Verlauf des zeitabhängigen Diffusionskoeffizienten zeigt subdiffusives Verhalten für kurze Beobachtungszeiten. Für Singulett-Exzitonen wechselt dieses Verhalten meist innerhalb der Lebensdauer des Exzitons in ein normales Diffusionsregime, während Triplett-Exzitonen das normale Regime deutlich langsamer erreichen. Das stärker anomale Verhalten der Triplett-Exzitonen wird auf eine ungleichmäßige Verteilung der Übergangsraten zurückgeführt. Beim Vergleich mit experimentell bestimmten Diffusionskonstanten muss das anomale Verhalten der Exzitonen berücksichtigt werden. Insgesamt stimmten simulierte und experimentelle Diffusionskonstanten für das Testsystem gut überein. Das Modellierungsverfahren sollte sich somit zur Charakterisierung des Exzitonentransports in neuen organischen Halbleitermaterialien eignen.

Development of Dynamic Constraint Models for a Model Based Transient Calibration Process

Model based calibration has gained popularity in recent years as a method to optimize increasingly complex engine systems. However virtually all model based techniques are applied to steady state calibration. Transient calibration is by and large an emerging technology. An important piece of any transient calibration process is the ability to constrain the optimizer to treat the problem as a dynamic one and not as a quasi-static process. The optimized air-handling parameters corresponding to any instant of time must be achievable in a transient sense; this in turn depends on the trajectory of the same parameters over previous time instances. In this work dynamic constraint models have been proposed to translate commanded to actually achieved air-handling parameters. These models enable the optimization to be realistic in a transient sense. The air handling system has been treated as a linear second order system with PD control. Parameters for this second order system have been extracted from real transient data. The model has been shown to be the best choice relative to a list of appropriate candidates such as neural networks and first order models. The selected second order model was used in conjunction with transient emission models to predict emissions over the FTP cycle. It has been shown that emission predictions based on air-handing parameters predicted by the dynamic constraint model do not differ significantly from corresponding emissions based on measured air-handling parameters.

A real time simulation model of glucose-insulin metabolism for type 1 diabetes patients

In this paper, a simulation model of glucose-insulin metabolism for Type 1 diabetes patients is presented. The proposed system is based on the combination of Compartmental Models (CMs) and artificial Neural Networks (NNs). This model aims at the development of an accurate system, in order to assist Type 1 diabetes patients to handle their blood glucose profile and recognize dangerous metabolic states. Data from a Type 1 diabetes patient, stored in a database, have been used as input to the hybrid system. The data contain information about measured blood glucose levels, insulin intake, and description of food intake, along with the corresponding time. The data are passed to three separate CMs, which produce estimations about (i) the effect of Short Acting (SA) insulin intake on blood insulin concentration, (ii) the effect of Intermediate Acting (IA) insulin intake on blood insulin concentration, and (iii) the effect of carbohydrate intake on blood glucose absorption from the gut. The outputs of the three CMs are passed to a Recurrent NN (RNN) in order to predict subsequent blood glucose levels. The RNN is trained with the Real Time Recurrent Learning (RTRL) algorithm. The resulted blood glucose predictions are promising for the use of the proposed model for blood glucose level estimation for Type 1 diabetes patients.

Teaching Cognitive Modeling Using PDP++

PDP++ is a freely available, open source software package designed to support the development, simulation, and analysis of research-grade connectionist models of cognitive processes. It supports most popular parallel distributed processing paradigms and artificial neural network architectures, and it also provides an implementation of the LEABRA computational cognitive neuroscience framework. Models are typically constructed and examined using the PDP++ graphical user interface, but the system may also be extended through the incorporation of user-written C++ code. This article briefly reviews the features of PDP++, focusing on its utility for teaching cognitive modeling concepts and skills to university undergraduate and graduate students. An informal evaluation of the software as a pedagogical tool is provided, based on the author’s classroom experiences at three research universities and several conference-hosted tutorials.

Atomic Quantum Simulation of U(N) and SU(N) Abelian Lattice Gauge Theories

Using ultracold alkaline-earth atoms in optical lattices, we construct a quantum simulator for U(N) and SU(N) lattice gauge theories with fermionic matter based on quantum link models. These systems share qualitative features with QCD, including chiral symmetry breaking and restoration at nonzero temperature or baryon density. Unlike classical simulations, a quantum simulator does not suffer from sign problems and can address the corresponding chiral dynamics in real time.

Extended kalman filter for estimation of parameters in nonlinear state-space models of biochemical networks.

It is system dynamics that determines the function of cells, tissues and organisms. To develop mathematical models and estimate their parameters are an essential issue for studying dynamic behaviors of biological systems which include metabolic networks, genetic regulatory networks and signal transduction pathways, under perturbation of external stimuli. In general, biological dynamic systems are partially observed. Therefore, a natural way to model dynamic biological systems is to employ nonlinear state-space equations. Although statistical methods for parameter estimation of linear models in biological dynamic systems have been developed intensively in the recent years, the estimation of both states and parameters of nonlinear dynamic systems remains a challenging task. In this report, we apply extended Kalman Filter (EKF) to the estimation of both states and parameters of nonlinear state-space models. To evaluate the performance of the EKF for parameter estimation, we apply the EKF to a simulation dataset and two real datasets: JAK-STAT signal transduction pathway and Ras/Raf/MEK/ERK signaling transduction pathways datasets. The preliminary results show that EKF can accurately estimate the parameters and predict states in nonlinear state-space equations for modeling dynamic biochemical networks.