Variability in exposure to ambient ultrafine particles in urban schools: Comparative assessment between Australia and Spain

Ambient ultrafine particle number concentrations (PNC) have inhomogeneous spatio-temporal distributions and depend on a number of different urban factors, including background conditions and distant sources. This paper quantitatively compares exposure to ambient ultrafine particles at urban schools in two cities in developed countries, with high insolation climatic conditions, namely Brisbane (Australia) and Barcelona (Spain). The analysis used comprehensive indoor and outdoor air quality measurements at 25 schools in Brisbane and 39 schools in Barcelona. PNC modes were analysed with respect to ambient temperature, land use and urban characteristics, combined with the measured elemental carbon concentrations, NOx (Brisbane) and NO2 (Barcelona). The trends and modes of the quantified weekday average daily cycles of ambient PNC exhibited significant differences between the two cities. PNC increases were observed during traffic rush hours in both cases. However, the mid-day peak was dominant in Brisbane schools and had the highest contribution to total PNC for both indoors and outdoors. In Barcelona, the contribution from traffic was highest for ambient PNC, while the mid-day peak had a slightly higher contribution for indoor concentrations. Analysis of the relationships between PNC and land use characteristics in Barcelona schools showed a moderate correlation with the percentage of road network area and an anti-correlation with the percentage of green area. No statistically significant correlations were found for Brisbane. Overall, despite many similarities between the two cities, school-based exposure patterns were different. The main source of ambient PNC at schools was shown to be traffic in Barcelona and mid-day new particle formation in Brisbane. The mid-day PNC peak in Brisbane could have been driven by the combined effect of background and meteorological conditions, as well as other local/distant sources. The results have implications for urban development, especially in terms of air quality mitigation and management at schools.

Urban energy fluxes in Helsinki and their high frequency spectral corrections

Inadvertent climate modification has led to an increase in urban temperatures compared to the surrounding rural area. The main reason for the temperature rise is the altered energy portioning of input net radiation to heat storage and sensible and latent heat fluxes in addition to the anthropogenic heat flux. The heat storage flux and anthropogenic heat flux have not yet been determined for Helsinki and they are not directly measurable. To the contrary, turbulent fluxes of sensible and latent heat in addition to net radiation can be measured, and the anthropogenic heat flux together with the heat storage flux can be solved as a residual. As a result, all inaccuracies in the determination of the energy balance components propagate to the residual term and special attention must be paid to the accurate determination of the components. One cause of error in the turbulent fluxes is the fluctuation attenuation at high frequencies which can be accounted for by high frequency spectral corrections. The aim of this study is twofold: to assess the relevance of high frequency corrections to water vapor fluxes and to assess the temporal variation of the energy fluxes. Turbulent fluxes of sensible and latent heat have been measured at SMEAR III station, Helsinki, since December 2005 using the eddy covariance technique. In addition, net radiation measurements have been ongoing since July 2007. The used calculation methods in this study consist of widely accepted eddy covariance data post processing methods in addition to Fourier and wavelet analysis. The high frequency spectral correction using the traditional transfer function method is highly dependent on relative humidity and has an 11% effect on the latent heat flux. This method is based on an assumption of spectral similarity which is shown not to be valid. A new correction method using wavelet analysis is thus initialized and it seems to account for the high frequency variation deficit. Anyhow, the resulting wavelet correction remains minimal in contrast to the traditional transfer function correction. The energy fluxes exhibit a behavior characteristic for urban environments: the energy input is channeled to sensible heat as latent heat flux is restricted by water availability. The monthly mean residual of the energy balance ranges from 30 Wm-2 in summer to -35 Wm-2 in winter meaning a heat storage to the ground during summer. Furthermore, the anthropogenic heat flux is approximated to be 50 Wm-2 during winter when residential heating is important.

Embedding Indigenous knowledges: An Australian case study of urban and remote teaching practicum

In this chapter we propose that there are certain conditions that enable the agency of pre-service teachers to enact curriculum decision-making within their pedagogical relationships with their supervising teachers as they endeavour to embed Indigenous knowledges (IK) during the teaching practicum. The case study, underpinned by decolonising methodologies, centred upon pre-service teacher preparation at one Australian university, where we investigated how role modelling in urban and remote schools occurred in the learning and teaching relationships between pre-service teachers on practicum and their supervising teachers. This chapter draws from an Office of Learning and Teaching (OLT) sponsored project at one Australian university; a full report on this project has been documented (see McLaughlin, Whatman and Nielsen, 2014). We commence with a discussion of decolonising and critical pedagogical spaces as the conceptual framework for the embedding Indigenous knowledges and perspectives in curricula and pedagogy. Our focus then shifts to a contextual overview of the development of Indigenous Knowledges (IK) in Australian school and university curriculum, providing a standpoint from which to consider the unfolding case study.

Defining the density debate in Brisbane: how urban consolidation is represented in the media

Rapid population growth, changing demographic profiles and increased focus on sustainable urban form has led to significant changes in settlement patterns in Australian cities. Growth management strategies are increasingly employed to help cities manage strain on infrastructure, housing and ecosystems. Urban consolidation is one such strategy and has been adopted by all Australian capital cities. Despite strong governmental support, urban consolidation has triggered much academic debate and has often been accompanied by staunch community opposition and complaints from the development industry about barriers to the provision of higher density housing. Greater understanding of stakeholder representations of higher density housing is important for planning, given the strong policy focus on urban consolidation nationally. This paper contributes to existing urban consolidation literature by empirically demonstrating how urban consolidation is represented in Brisbane’s newspaper media through the use of metaphors. Its conceptual departure point is Social Representations Theory, drawing on the theory’s notion of objectification to illustrate how the media translates the abstract notion of urban consolidation into a tangible and understandable object. The objectification of urban consolidation is identified and discussed relative to four themes: land use conflict; growth; neighbourhood change and apartment living. This paper argues that understanding stakeholder representations is important for planners seeking to promote and negotiate delivery of higher density development. It concludes that stakeholder representations can highlight key areas of contention to be addressed by planners, provide indications on the likelihood of public acceptance of increased housing densities and delineate the boundaries of urban consolidation debates.

Shaping urban consolidation debates: Social representations in Brisbane newspaper media

Recent international trends towards urban consolidation, intended to reduce outward urban sprawl by concentrating growth within existing neighbourhoods, can cause contention in cities. Understanding how the mass media represents urban consolidation can lead to more informed and democratic planning practices. This paper employs Social Representations Theory to identify and understand representations of urban consolidation in newspaper media. The theory recognises that the media is a key purveyor of public discourse and can reflect, shape or suppress ideas circulating in society. This novel approach has not previously been applied to understanding social representations of urban consolidation strategies in the mass media. The rapidly growing and changing city of Brisbane, Australia, is utilised as a case study. Brisbane is situated in South East Queensland, the fastest growing region in Australia, and is governed by regional and local planning policies that strongly support increased densities in existing urban areas. Findings from a quantitative textual analysis of 449 articles published in Brisbane newspapers between 2007 and 2014 reveal key clusters and classes of co-occurring words that represent dominant social representations apparent in the newspaper corpus. The paper provides two key conclusions. The first is that social representations occurring in mass media represent an important source of information about ‘common sense’ understandings and evaluations of urban consolidation debates. The second is that urban consolidation is represented as a ultifaceted issue, including interrelated themes of housing,sustainable population growth, investment strategies and the interplay between politics and planning

Chemical and source characterisation of size-segregated urban air particulate matter

Recent epidemiological studies have shown a consistent association of the mass concentration of urban air thoracic (PM10) and fine (PM2.5) particles with mortality and morbidity among cardiorespiratory patients. However, the chemical characteristics of different particulate size ranges and the biological mechanisms responsible for these adverse health effects are not well known. The principal aims of this thesis were to validate a high volume cascade impactor (HVCI) for the collection of particulate matter for physicochemical and toxicological studies, and to make an in-depth chemical and source characterisation of samples collected during different pollution situations. The particulate samples were collected with the HVCI, virtual impactors and a Berner low pressure impactor in six European cities: Helsinki, Duisburg, Prague, Amsterdam, Barcelona and Athens. The samples were analysed for particle mass, common ions, total and water-soluble elements as well as elemental and organic carbon. Laboratory calibration and field comparisons indicated that the HVCI can provide a unique large capacity, high efficiency sampling of size-segregated aerosol particles. The cutoff sizes of the recommended HVCI configuration were 2.4, 0.9 and 0.2 μm. The HVCI mass concentrations were in a good agreement with the reference methods, but the chemical composition of especially the fine particulate samples showed some differences. This implies that the chemical characterization of the exposure variable in toxicological studies needs to be done from the same HVCI samples as used in cell and animal studies. The data from parallel, low volume reference samplers provide valuable additional information for chemical mass closure and source assessment. The major components of PM2.5 in the virtual impactor samples were carbonaceous compounds, secondary inorganic ions and sea salt, whereas those of coarse particles (PM2.5-10) were soil-derived compounds, carbonaceous compounds, sea salt and nitrate. The major and minor components together accounted for 77-106% and 77-96% of the gravimetrically-measured masses of fine and coarse particles, respectively. Relatively large differences between sampling campaigns were observed in the organic carbon content of the PM2.5 samples as well as the mineral composition of the PM2.5-10 samples. A source assessment based on chemical tracers suggested clear differences in the dominant sources (e.g. traffic, residential heating with solid fuels, metal industry plants, regional or long-range transport) between the sampling campaigns. In summary, the field campaigns exhibited different profiles with regard to particulate sources, size distribution and chemical composition, thus, providing a highly useful setup for toxicological studies on the size-segregated HVCI samples.

Monitoring temporal changes in use of two cathinones in a large urban catchment in Queensland, Australia

Wastewater analysis was used to examine prevalence and temporal trends in the use of two cathinones, methylone and mephedrone, in an urban population (>200,000 people) in South East Queensland, Australia. Wastewater samples were collected from the inlet of the sewage treatment plant that serviced the catchment from 2011 to 2013. Liquid chromatography coupled with tandem mass spectrometry was used to measure mephedrone and methylone in wastewater sample using direct injection mode. Mephedrone was not detected in any samples while methylone was detected in 45% of the samples. Daily mass loads of methylone were normalized to the population and used to evaluate methylone use in the catchment. Methylone mass loads peaked in 2012 but there was no clear temporal trend over the monitoring period. The prevalence of methylone use in the catchment was associated with the use of MDMA, the more popular analogue of methylone, as indicated by other complementary sources. Methylone use was stable in the study catchment during the monitoring period whereas mephedrone use has been declining after its peak in 2010. More research is needed on the pharmacokinetics of emerging illicit drugs to improve the applicability of wastewater analysis in monitoring their use in the population.

Controls on trace metals in urban stream sediments : implications for pollution monitoring using sediment chemistry data

Contamination of urban streams is a rising topic worldwide, but the assessment and investigation of stormwater induced contamination is limited by the high amount of water quality data needed to obtain reliable results. In this study, stream bed sediments were studied to determine their contamination degree and their applicability in monitoring aquatic metal contamination in urban areas. The interpretation of sedimentary metal concentrations is, however, not straightforward, since the concentrations commonly show spatial and temporal variations as a response to natural processes. The variations of and controls on metal concentrations were examined at different scales to increase the understanding of the usefulness of sediment metal concentrations in detecting anthropogenic metal contamination patterns. The acid extractable concentrations of Zn, Cu, Pb and Cd were determined from the surface sediments and water of small streams in the Helsinki Metropolitan region, southern Finland. The data consists of two datasets: sediment samples from 53 sites located in the catchment of the Stream Gräsanoja and sediment and water samples from 67 independent catchments scattered around the metropolitan region. Moreover, the sediment samples were analyzed for their physical and chemical composition (e.g. total organic carbon, clay-%, Al, Li, Fe, Mn) and the speciation of metals (in the dataset of the Stream Gräsanoja). The metal concentrations revealed that the stream sediments were moderately contaminated and caused no immediate threat to the biota. However, at some sites the sediments appeared to be polluted with Cu or Zn. The metal concentrations increased with increasing intensity of urbanization, but site specific factors, such as point sources, were responsible for the occurrence of the highest metal concentrations. The sediment analyses revealed, thus a need for more detailed studies on the processes and factors that cause the hot spot metal concentrations. The sediment composition and metal speciation analyses indicated that organic matter is a very strong indirect control on metal concentrations, and it should be accounted for when studying anthropogenic metal contamination patterns. The fine-scale spatial and temporal variations of metal concentrations were low enough to allow meaningful interpretation of substantial metal concentration differences between sites. Furthermore, the metal concentrations in the stream bed sediments were correlated with the urbanization of the catchment better than the total metal concentrations in the water phase. These results suggest that stream sediments show true potential for wider use in detecting the spatial differences in metal contamination of urban streams. Consequently, using the sediment approach regional estimates of the stormwater related metal contamination could be obtained fairly cost-effectively, and the stability and reliability of results would be higher compared to analyses of single water samples. Nevertheless, water samples are essential in analysing the dissolved concentrations of metals, momentary discharges from point sources in particular.

Flying-foxes in the Australian urban environment - community attitudes and opinions

The urban presence of flying-foxes (pteropid bats) in eastern Australia has increased in the last 20 years, putatively reflecting broader landscape change. The influx of large numbers often precipitates community angst, typically stemming from concerns about loss of social amenity, economic loss or negative health impacts from recently emerged bat-mediated zoonotic diseases such as Hendra virus and Australian bat lyssavirus. Local authorities and state wildlife authorities are increasingly asked to approve the dispersal or modification of flying-fox roosts to address expressed concerns, yet the scale of this concern within the community, and the veracity of the basis for concern are often unclear. We conducted an on-line survey to capture community attitudes and opinions on flying-foxes in the urban environment to inform management policy and decision-making. Analysis focused on awareness, concerns, and management options, and primarily compared responses from communities where flying-fox management was and was not topical at the time of the survey. While a majority of respondents indicated a moderate to high level of knowledge of both flying-foxes and Hendra virus, a substantial minority mistakenly believed that flying-foxes pose a direct infection risk to humans, suggesting miscommunication or misinformation, and the need for additional risk communication strategies. Secondly, a minority of community members indicated they were directly impacted by urban roosts, most plausibly those living in close proximity to the roost, suggesting that targeted management options are warranted. Thirdly, neither dispersal nor culling was seen as an appropriate management strategy by the majority of respondents, including those from postcodes where flying-fox management was topical. These findings usefully inform community debate and policy development and demonstrate the value of social analysis in defining the issues and options in this complex human - wildlife interaction. The mobile nature of flying-foxes underlines the need for a management strategy at a regional or larger scale, and independent of state borders.

Middleware for Mobile Sensing Applications in Urban Environments

Sensor networks represent an attractive tool to observe the physical world. Networks of tiny sensors can be used to detect a fire in a forest, to monitor the level of pollution in a river, or to check on the structural integrity of a bridge. Application-specific deployments of static-sensor networks have been widely investigated. Commonly, these networks involve a centralized data-collection point and no sharing of data outside the organization that owns it. Although this approach can accommodate many application scenarios, it significantly deviates from the pervasive computing vision of ubiquitous sensing where user applications seamlessly access anytime, anywhere data produced by sensors embedded in the surroundings. With the ubiquity and ever-increasing capabilities of mobile devices, urban environments can help give substance to the ubiquitous sensing vision through Urbanets, spontaneously created urban networks. Urbanets consist of mobile multi-sensor devices, such as smart phones and vehicular systems, public sensor networks deployed by municipalities, and individual sensors incorporated in buildings, roads, or daily artifacts. My thesis is that "multi-sensor mobile devices can be successfully programmed to become the underpinning elements of an open, infrastructure-less, distributed sensing platform that can bring sensor data out of their traditional close-loop networks into everyday urban applications". Urbanets can support a variety of services ranging from emergency and surveillance to tourist guidance and entertainment. For instance, cars can be used to provide traffic information services to alert drivers to upcoming traffic jams, and phones to provide shopping recommender services to inform users of special offers at the mall. Urbanets cannot be programmed using traditional distributed computing models, which assume underlying networks with functionally homogeneous nodes, stable configurations, and known delays. Conversely, Urbanets have functionally heterogeneous nodes, volatile configurations, and unknown delays. Instead, solutions developed for sensor networks and mobile ad hoc networks can be leveraged to provide novel architectures that address Urbanet-specific requirements, while providing useful abstractions that hide the network complexity from the programmer. This dissertation presents two middleware architectures that can support mobile sensing applications in Urbanets. Contory offers a declarative programming model that views Urbanets as a distributed sensor database and exposes an SQL-like interface to developers. Context-aware Migratory Services provides a client-server paradigm, where services are capable of migrating to different nodes in the network in order to maintain a continuous and semantically correct interaction with clients. Compared to previous approaches to supporting mobile sensing urban applications, our architectures are entirely distributed and do not assume constant availability of Internet connectivity. In addition, they allow on-demand collection of sensor data with the accuracy and at the frequency required by every application. These architectures have been implemented in Java and tested on smart phones. They have proved successful in supporting several prototype applications and experimental results obtained in ad hoc networks of phones have demonstrated their feasibility with reasonable performance in terms of latency, memory, and energy consumption.

Establishing turf grass increases soil greenhouse gas emissions in peri-urban environments

Urbanization is becoming increasingly important in terms of climate change and ecosystem functionality worldwide. We are only beginning to understand how the processes of urbanization influence ecosystem dynamics and how peri-urban environments contribute to climate change. Brisbane in South East Queensland (SEQ) currently has the most extensive urban sprawl of all Australian cities. This leads to substantial land use changes in urban and peri-urban environments and the subsequent gaseous emissions from soils are to date neglected for IPCC climate change estimations. This research examines how land use change effects methane (CH4) and nitrous oxide (N2O) fluxes from peri-urban soils and consequently influences the Global Warming Potential (GWP) of rural ecosystems in agricultural use undergoing urbanization. Therefore, manual and fully automated static chamber measurements determined soil gas fluxes over a full year and an intensive sampling campaign of 80 days after land use change. Turf grass, as the major peri-urban land cover, increased the GWP by 415 kg CO2-e ha 1 over the first 80 days after conversion from a well-established pasture. This results principally from increased daily average N2O emissions of 0.5 g N2O ha-1 d-1 from the pasture to 18.3 g N2O ha-1 d-1 from the turf grass due to fertilizer application during conversion. Compared to the native dry sclerophyll eucalypt forest, turf grass establishment increases the GWP by another 30 kg CO2-e ha 1. The results presented in this study clearly indicate the substantial impact of urbanization on soil-atmosphere gas exchange in form of non-CO2 greenhouse gas emissions particularly after turf grass establishment.

Diet of dingoes and other wild dogs in peri-urban areas of north-eastern Australia

Knowledge of the resource requirements of urban predators can improve our understanding of their ecology and assist town planners and wildlife management agencies in developing management approaches that alleviate human-wildlife conflicts. Here we examine food and dietary items identified in scats of dingoes in peri-urban areas of north-eastern Australia to better understand their resource requirements and the potential for dingoes to threaten locally fragmented populations of native fauna. Our primary aim was to determine what peri-urban dingoes eat, and whether or not this differs between regions. We identified over 40 different food items in dingo scats, almost all of which were mammals. Individual species commonly observed in dingo scats included agile wallabies, northern brown bandicoots and swamp wallabies. Birds were relatively common in some areas but not others, as were invertebrates. Dingoes were identified as a significant potential threat to fragmented populations of koalas. Dietary overlap was typically very high or near-identical between regions, indicating that peri-urban dingoes ate the same types or sizes of prey in different areas. Future studies should seek to quantify actual and perceived impacts of, and human attitudes towards, peri-urban dingoes, and to develop management strategies with a greater chance of reducing human-wildlife conflicts.

The professional development, resource and support needs of rural and urban ICT teachers

This paper presents findings from the SiMERR National Survey concerning the need priorities of secondary ICT teachers for professional development, resources and student learning experiences. The findings - drawn from a survey of 237 secondary ICT teachers across Australia - provide an opportunity to compare the needs of teachers working in metropolitan, provincial and remote schools. The study found that vacant ICT positions are difficult to fill ond that the novel on dynamic nature of ICT requires teachers to have more extensive opportunities for on-the-job training, collegial collaboration and mentoring than is the case for teachers of more traditional subjects like science and mathematics. The study also found that ICT teachers are commonly required to manage and maintain ICT resources and to assist other staff to use ICT resources, while being allocated insufficient time in which to do these additional activities. The implications of these and other findings are discussed along with recommendations to help address the needs of ICT teachers in different parts of Australia.

The creative suburb: Building and urban designs for suburban innovators

Influential creative industries and creative place thinkers Richard Florida and Charles Landry agree that creativity is necessary for a prospering liveable and, therefore, sustainable city. Following Florida’s work, the ‘creative class’ has become central to what has turned out to be city-centre-centric growth policies. However, until the Queensland University of Technology’s Australian Research Council sponsored research into “creative suburbia”, few researchers had demonstrated – let alone challenged – the notion that a substantial cohort of creative industries workers might prefer to live and work at home in the suburbs rather than in city centres. The “creative suburb” work builds on the creative suburbia research. In a practice-led and property development industry embedded inquiry, the creative suburb draws on significant primary research with suburban, home-based, creative industries workers, vernacular architecture, and town planning in the Toowoomba region, in the state of Queensland, Australia, as inspiration for a series of new building and urban designs available for innovators operating in new suburban greenfield situations and suburban areas undergoing a refit in Queensland and possibly further afield. This paper focuses on one building design informed by this inquiry, with the intention of its construction as a ’showcasestudy’ ‘homeworkhouse’, suitable for creative industries workers in the Toowoomba region.

Assessing the significance of climate and community factors on urban water demand

Ensuring adequate water supply to urban areas is a challenging task due to factors such as rapid urban growth, increasing water demand and climate change. In developing a sustainable water supply system, it is important to identify the dominant water demand factors for any given water supply scheme. This paper applies principal components analysis to identify the factors that dominate residential water demand using the Blue Mountains Water Supply System in Australia as a case study. The results show that the influence of community intervention factors (e.g. use of water efficient appliances and rainwater tanks) on water demand are among the most significant. The result also confirmed that the community intervention programmes and water pricing policy together can play a noticeable role in reducing the overall water demand. On the other hand, the influence of rainfall on water demand is found to be very limited, while temperature shows some degree of correlation with water demand. The results of this study would help water authorities to plan for effective water demand management strategies and to develop a water demand forecasting model with appropriate climatic factors to achieve sustainable water resources management. The methodology developed in this paper can be adapted to other water supply systems to identify the influential factors in water demand modelling and to devise an effective demand management strategy.