Optimization of Soil Stabilization with Class C Fly Ash, January 1987

Previous Iowa DOT sponsored research has shown that some Class C fly ashes are ementitious (because calcium is combined as calcium aluminates) while other Class C ashes containing similar amounts of elemental calcium are not (1). Fly ashes from modern power plants in Iowa contain significant amounts of calcium in their glassy phases, regardless of their cementitious properties. The present research was based on these findings and on the hyphothesis that: attack of the amorphous phase of high calcium fly ash could be initiated with trace additives, thus making calcium available for formation of useful calcium-silicate cements. Phase I research was devoted to finding potential additives through a screening process; the likely chemicals were tested with fly ashes representative of the cementitious and non-cementitious ashes available in the state. Ammonium phosphate, a fertilizer, was found to produce 3,600 psi cement with cementitious Neal #4 fly ash; this strength is roughly equivalent to that of portland cement, but at about one-third the cost. Neal #2 fly ash, a slightly cementitious Class C, was found to respond best with ammonium nitrate; through the additive, a near-zero strength material was transformed into a 1,200 psi cement. The second research phase was directed to optimimizing trace additive concentrations, defining the behavior of the resulting cements, evaluating more comprehensively the fly ashes available in Iowa, and explaining the cement formation mechanisms of the most promising trace additives. X-ray diffraction data demonstrate that both amorphous and crystalline hydrates of chemically enhanced fly ash differ from those of unaltered fly ash hydrates. Calciumaluminum- silicate hydrates were formed, rather than the expected (and hypothesized) calcium-silicate hydrates. These new reaction products explain the observed strength enhancement. The final phase concentrated on laboratory application of the chemically-enhanced fly ash cements to road base stabilization. Emphasis was placed on use of marginal aggregates, such as limestone crusher fines and unprocessed blow sand. The nature of the chemically modified fly ash cements led to an evaluation of fine grained soil stabilization where a wide range of materials, defined by plasticity index, could be stabilized. Parameters used for evaluation included strength, compaction requirements, set time, and frost resistance.

Circum-Alpine marine circulation and paleoenvironmental conditions during the Miocene

Trace element and isotopic compositions of marine fossils and sediment were analyzed from several Miocene deposits in the circum-Alpine region in order to reconstruct the paleoceanographic and paleoclimatic changes related to sea level changes, basin evolution and Alpine orogeny. To the north and the east the Alps were border by an epicontinental sea, the Paratethys, while to the south the Mediterranean surrounded the uplifting mountains during the Miocene. The thesis mainly focused on sediments and fossils sampled from Miocene beds of these two oceanic provinces. The north Alpine Molasse, the Vienna and Pannonian Basins were located in the Western and Central Paratethys. O-isotope compositions of well-preserved phosphatic fossils in these sediments support deposition under sub-tropical to warm-temperate climate with water temperatures between 14 to 28 °C for the Miocene. δ18O values of fossil shark teeth from different horizons vary similarly to those of the global trend until the end of the Badenian, however the δ18O values show wider range, which indicates local effects iii the sub-basins. The trend of 87Sr/86Sr in the samples roughly agrees with an open ocean environment for the Miocene. Yet a number of samples deviate from typical open ocean compositions with higher ratios suggesting modification of seawater by local and old terrestrial sources. In contrast, two exceptional teeth from the locality of La Moliere have extremely low δ18O values and low 87Sr/86Sr. However, the REE patterns of their enameloid are similar to those of teeth having O and Sr isotopic compositions typical of a marine setting at this site. Collectively, this suggests that the two teeth formed while the sharks frequented a freshwater environment with very low 18O-content and 87Sr/86Sr controlled by Mesozoic calcareous rocks. This is consistent with a paleogeography of high-elevation (~2300m) Miocene Alps adjacent to a marginal sea. The local effects are also reflected in the εNd values of the Paratethyan fossils, which is compatible with input from ancient crystalline rocks and Mesozoic sediments, while other samples with elevated εNd values indicate an influence of Neogene volcanism on the water budget. Excluding samples whose isotopic compositions reflect a local influence on the water column, an average εNd value of -7.9 ± 0.5 may be inferred for the Paratethys seawater. This value is indistinguishable from the Miocene value of the Indian Ocean, supporting a dominant role of ludo-Pacific water masses in the Paratethys. Regarding the Mediterranean, stable C-and O-isotope compositions of benthic and planktonic foraminifera from the Umbria-Marche region (UMC) have an offset typical for their habitats and the changes in composition mimic global changes, suggesting that the regional conditions of climate and the carbon cycle were controlled by global changes. The radiogenic isotope compositions of the fossil assemblages allow for distinction of periods. From 25 to 19 Ma, high εNd values and low 87Sr/86Sr of sediments and fossils support intense tectonism and volcanism, related to the opening of the western Mediterranean. Between 19 and 13 Ma the Mediterranean has εNd values that are largely controlled by incursion of Indian Ocean water. Brief periods of local hinterland control on seawater compositions are indicated by spikes in the εNd record, coinciding with volcanic events and a short sea-level decrease at about 15.2 Ma. Lower 87Sr/86Sr compared to the open ocean is compatible with rapid uplift of the hinterland and intense influx of Sr from Mesozoic carbonates of the western Apennines, while higher 87Sr/86Sr for other sites indicates erosion of old crustal silicate rocks. Finally, from 13 to 7 Ma the fossils have 87Sr/86Sr similar to those of Miocene seawater and their εNd values indicates fluctuating influence of Atlantic, and Indian Ocean or Paratethys sources of seawater entering the Mediterranean, driven by global sealevel changes and local tectonism. RÉSUMÉ DE LA THÈSE Les compositions en éléments traces et isotopiques de fossiles marins et de sédiments on été analysées à partir de nombreux dépôts marins dans la région circum Alpine dans le but de reconstruire les changements paléocéanographiques et paléoclimatiques liés aux changements du niveau marin, à l'évolution en bassins et à l'orogénie alpine. Au nord et à l'est des Alpes, une mer épicontinentale appelée Paratéthys s'est ouverte, alors que plus au sud la mer Méditerranée bordait au Miocène les Alpes naissantes. Le but de cette recherche est de se concentrer sur les sédiments et les fossiles provenant des couches du Miocènes de ces deux provinces marines. Les bassins de la Molasse Alpine du nord, de Vienne et Pannonien étaient situés au niveau de la Paratéthys Occidentale et Centrale. Les compositions isotopiques de l'oxygène de fossiles phosphatés bien préservés dans ces sédiments étayent la théorie d'un dépôt sous un climat subtropical à tempéré chaud avec des températures entre 14 et 28°C pendant le Miocène. Les valeurs δ18O des fossiles sont similaires à la tendance globale jusqu'à la fin du Badénien. Cependant les larges fluctuations en δ18O indiquent des effets locaux au niveau des sous bassins. En outre, deux dents de requin exceptionnelles présentent des valeurs extrêmement basses de δ18O. Ces données suggèrent que ces deux dents se sont formées alors que les requins fréquentaient un environnement d'eau douce avec de faibles valeurs de 18O. Le calcul de la composition isotopique de l'oxygène de cette eau douce permet d'obtenir une estimation de la paléoélévatian moyenne des Alpes du Miocène (~2300m). La tendance 87Sr/86Sr pour ces échantillons concorde approximativement avec un environnement d'océan ouvert au cours du Miocène. Toutefois un nombre d'échantillons dévie des compositions d'océan ouvert typiques, avec des rapports élevés suggérant des modifications de l'eau de mer par des sources locales et terrestres. Les effets locaux sont aussi reflétés au niveau des valeurs en εNd des fossiles paratéthysiens. Ceci est cohérent avec un apport d'anciennes roches cristallines et de sédiments mésozoïques, tandis que d'autres échantillons avec des valeurs hautes de εNd indiquent une influence d'un volcanisme néogène dans le budget marin. En excluant les échantillons dont les compositions isotopiques confirment une influence locale, une valeur moyenne de εNd de 7.9 t 0.5 peut être déduite pour l'eau de la Parathétys. Cette valeur est semblable à la valeur correspondant à l'Océan Indien durant le Miocène, confirmant un rôle dominant de cet océan dans la Paratéthys. Au niveau de la Méditerranée, les compositions en isotopes stables du Carbone et de l'Oxygène de foraminifères planctoniques et benthique de la région Umbria-Marche présentent un offset typique à leurs habitats. De plus les changements dans leurs compositions suivent les changements globaux, suggérant ainsi que les conditions climatiques régionales et le cycle du carbone étaient contrôlés par des phénomènes globaux. La composition en isotopes radiogéniques d'assemblages fossiles permet une reconnaissance sur trois périodes distinctes. De 25 à 19 millions d'années (Ma), des valeurs élevées de εNd et un faible rapport 87Sr/86Sr dans les sédiments soutiennent l'idée d'une activité tectonique et volcanique intense, liée à l'ouverture de la Méditerranée occidentale. Entre 19 et 13 Ma, la Méditerranée montre des valeurs de εNd qui sont largement contrôlées par une incursion d'eau provenant de l'Océan Indien. En effet, aux alentours de 15,2 Ma, des pics dans l'enregistrement des valeurs de εNd, coïncidant avec des événements volcaniques et de brèves diminutions du niveau marin. Enfin, de 13 à 7 Ma, les fossiles ont des rapports ß7Sr/8fiSr similaires à ceux de l'eau de mer au Miocène. Leurs valeurs de εNd indiquent une influence changeante de l'océan Atlantique, et de l'océan Indien ou des sources d'eau de merde la Parathétys qui entrent dans les bassins méditerranéens. Ce changement est guidé par des modifications globales du niveau marin et par la tectonique locale. RÉSUMÉ DE LA THÈSE (POUR LE GRAND PUBLIC) Les analyses des compositions en éléments traces et isotopiques des fossiles marins sont un outil très utile pour reconstruire les conditions océaniques et climatiques anciennes. Ce travail de thèse se concentre sur les sédiments déposés dans un environnement marin proches des Alpes au cours du Miocène, entre 23 et 7 millions d'années (Ma). Cette période est caractérisée par une tectonique alpine active, ainsi que par des changements climatiques et océanographiques globaux importants. Dans le but de tracer ces changements, les compositions isotopiques du Strontium, du Néodyme, de l'Oxygène et du Carbone ont été analysées dans des fossiles bien préservés ainsi que les sédiments contemporains. Les échantillons proviennent de deux provinces océaniques distinctes, la première est la Mer Méditerranée, et l'autre est une mer épicontinentale appelée Parathétys, qui existait au nord et à l'est des Alpes durant le Miocène. Au niveau de la Parathétys Occidentale et Orientale, les compositions isotopiques d'oxygène de dents de requins confirment un dépôt sous un climat subtropical à tempéré chaud avec des températures d'eau entre 14 et 28°C au Miocène. En outre, deux dents de requins exceptionnelles ont enregistré des compositions isotopiques d'oxygène extrêmement basses. Cela suggère que ces deux dents se sont formées alors que les requins entraient dans un système d'eau douce. Le calcul de la composition isotopique de l'oxygène de cette eau douce permet d'obtenir une estimation de la paléoélévation des Alpes au Miocène qui est aussi élevée que celle d'aujourd'hui. La tendance isotopique du Strontium pour ces échantillons concorde approximativement avec un environnement d'océan ouvert. Cependant un certain nombre d'échantillons indique des modifications de l'eau de mer par des sources terrestres locales. Les effets locaux sont aussi visibles au niveau des compositions isotopiques du Néodyme, qui sont en accord avec un apport provenant de roches cristallines anciennes et de sédiments du Mésozoïque, alors que d'autres échantillons indiquent une influence volcanique néogène dans le budget marin. A l'exclusion des échantillons dont les compositions correspondent à une influence locale, les compositions isotopiques du Néodyme de la Parathétys sont très similaires aux valeurs de l'Océan Indien, montrant ainsi un rôle important des masses d'eau IndoPacifiques dans cette région. Au niveau de la Méditerranée, les compositions en isotopes stables du Carbone et de l'Oxygène de foraminifères planctoniques et benthique de la région Umbria-Marche présentent un offset typique à leurs habitats. De plus, les changements dans leurs compositions suivent les changements globaux, suggérant ainsi que les conditions climatiques régionales et le cycle du carbone étaient contrôlés par des phénomènes globaux. La composition en isotopes radiogéniques d'assemblages fossiles permet une reconnaissance sur trois périodes distinctes. De 25 à 19 Ma, des rapport isotopiques élevés pour le Néodyme et faibles pour le Strontium dans les sédiments et les fossiles soutiennent l'idée d'une activité tectonique et volcanique intense, liée à l'ouverture de la Méditerranée occidentale. Entre 19 et 13 Ma, la Méditerranée présente des rapports isotopiques du Néodyme qui sont largement contrôlés par une incursion d'eau provenant de l'Océan Indien. En effet, aux alentours de 15,2 Ma, des pics dans l'enregistrement des valeurs des isotopes du Néodyme coïncident avec des événements volcaniques et de brèves diminutions du niveau marin. Finalement, de 13 à 7 Ma, les fossiles ont des rapports isotope Strontium similaires à ceux de l'eau de mer au Miocène. Les rapports isotopiques du Néodyme indiquent une influence changeante de l'océan Atlantique, et de l'océan Indien ou des sources d'eau de mer de la Parathétys qui entrent dans les bassins méditerranéens. Ce changement est guidé par des modifications globales du niveau marin et par la tectonique locale.

Mineral inventory of continuously erupting basaltic andesites at Arenal volcano, Costa Rica: implications for interpreting monotonous, crystal-rich, mafic arc stratigraphies

Except for the first 2 years since July 29, 1968, Arenal volcano has continuously erupted compositionally monotonous and phenocryst-rich (similar to35%) basaltic andesites composed of plagioclase (plag), orthopyroxene (opx), clinopyroxene (cpx), spinel olivine. Detailed textural and compositional analyses of phenocrysts, mineral inclusions, and microlites reveal comparable complexities in any given sample and identify mineral components that require a minimum of four crystallization environments. We suggest three distinct crystallization environments crystallized low Mg# (<78) silicate phases from andesitic magma but at different physical conditions, such as variable pressure of crystallization and water conditions. The dominant environment, i.e., the one which accounts for the majority of minerals and overprinted all other assemblages near rims of phenocrysts, cocrystallized clinopyroxene (Mg# similar to71-78), orthopyroxene (Mg# similar to71-78), titanomagnetite and plagioclase (An(60) to An(85)). The second environment cocrystallized clinopyroxene (Mg# 71-78), olivine (<Fo(78)), titanomagnetite, and very high An (similar to90) plagioclase, while the third cocrystallized clinopyroxene (Mg# 71-78) with high (>7) Al/Ti and high (>4 wt.%) Al2O3, titanomagnetite with considerable Al2O3 (10-18 wt.%) and possibly olivine but appears to lack plagioclase. A fourth crystallization environment is characterized by clinopyroxene (e.g., Mg#=similar to78-85; Cr2O3=0.15-0.7 wt.%), Al-, Cr-rich spinel olivine (similar toFo(80)), and in some circumstances high-An (>80) plagioclase. This assemblage seems to record mafic inputs into the Arenal system and crystallization at high to low pressures. Single crystals cannot be completely classified as xenocrysts, antecrysts (cognate crystals), or phenocrysts, because they often contain different parts each representing a different crystallization environment and thus belong to different categories. Bulk compositions are mostly too mafic to have crystallized the bulk of ferromagnesian minerals and thus likely do not represent liquid compositions. On the other hand, they are the cumulative products of multiple mixing events assembling melts and minerals from a variety of sources. The driving force for this multistage mixing evolution to generate erupting basaltic andesites is thought to be the ascent of mafic magma from lower crustal levels to subvolcanic depths which at the same time may also go through compositional modification by fractionation and assimilation of country rocks. Thus, mafic magmas become basaltic andesite through mixing, fractionation and assimilation by the time they arrive at subvolcanic depths. We infer new increments of basaltic andesite are supplied nearly continuously to the subvolcanic reservoir concurrently to the current eruption and that these new increments are blended into the residing, subvolcanic magma. Thus, the compositional monotony is mostly the product of repetitious production of very similar basaltic andesite. Furthermore, we propose that this quasi-constant supply of small increments of magma is the fundamental cause for small-scale, decade-long continuous volcanic activity; that is, the current eruption of Arenal is flux-controlled by inputs of mantle magmas. (C) 2004 Elsevier B.V. All rights reserved.

The Gronnedal-Ika carbonatite-syenite complex, South Greenland: Carbonatite formation by liquid immiscibility

The Gronnedal-Ika complex is dominated by layered nepheline syenites which were intruded by a xenolithic syenite and a central plug of calcite to calcite-siderite carbonatite. Aegirine-augite, alkali feldspar and nepheline are the major mineral phases in the syenites, along with rare calcite. Temperatures of 680-910degreesC and silica activities of 0.28-0.43 were determined for the crystallization of the syenites on the basis of mineral equilibria. Oxygen fugacities, estimated using titanomagnetite compositions, were between 2 and 5 log units above the fayalite-magnetite-quartz buffer during the magmatic stage. Chondrite-normalized REE patterns of magmatic calcite in both carbonatites and syenites are characterized by REE enrichment (La-CN-Yb-CN = 10-70). Calcite from the carbonatites has higher Ba (similar to5490 ppm) and lower HREE concentrations than calcite from the syenites (54-106 ppm Ba). This is consistent with the behavior of these elements during separation of immiscible silicate-carbonate liquid pairs. epsilon(Nd)(T = 1.30 Ga) values of clinopyroxenes from the syenites vary between +1.8 and +2.8, and epsilon(Nd)(T) values of whole-rock carbonatites range from +2.4 to +2.8. Calcite from the carbonatites has delta(18)O values of 7.8 to 8.6parts per thousand and delta(13)C values of -3.9 to -4.6parts per thousand. delta(18)O values of clinopyroxene separates from the nepheline syenites range between 4.2 and 4.9parts per thousand. The average oxygen isotopic composition of the nepheline syenitic melt was calculated based on known rock-water and mineral-water isotope fractionation to be 5.7 +/- 0.4parts per thousand. Nd and C-O isotope compositions are typical for mantle-derived rocks and do not indicate significant crustal assimilation for either syenite or carbonatite magmas. The difference in delta(18)O between calculated syenitic melts and carbonatites, and the overlap in epsilon(Nd) values between carbonatites and syenites, are consistent with derivation of the carbonatites from the syenites via liquid immiscibility.

Development of a Rational Characterization Method for Iowa Fly Ash, HR-286, 1988

This research project was conducted in an attempt to determine the cause of paste strength variability in Iowa fly ashes and to develop test methods to more adequately reflect fly ash physical and chemical characteristics. An extensive three year sampling and testing program was developed and initiated which incorporated fly ash from several Iowa power plants. Power plant design and operating data were collected. The variability was directly linked to power plant maintenance schedules and to sodium carbonate coal pretreatment. Fly ash physical and chemical properties can change drastically immediately before and after a maintenance outage. The concentrations of sulfate bearing minerals in the fly ash increases sharply during shutdown. Chemical, mineralogical, and physical testing indicated that the sodium, sulfate bearing minerals, lime and tricalcium aluminate contents of the fly ashes play important roles in the development of hydration reaction products in fly ash pastes. The weak pastes always contained ettringite as the major reaction product. The strong pastes contained straetlingite and monosulfoaluminate as the major reaction products along with minor amounts of ettringite. Recommendations for testing procedure changes and suggested interim test methods are presented.

Expansive Mineral Growth and Concrete Deterioration, HR-384, 1997

A significant question is: What role does newly-formed expansive mineral growth play in the premature deterioration of concrete? These minerals (ettringite and brucite) are formed in cement paste as a result of chemical reactions involving cement and coarse/fine aggregate. Petrographic observations and SEM/EDAX analysis were conducted in order to determine chemical and mineralogical changes in the aggregate and cement paste of samples taken from Iowa concrete highways that showed premature deterioration. Mechanisms involved in deterioration were investigated. A second objective was to investigate whether deicer solutions exacerbate the formation of expansive minerals and concrete deterioration. Magnesium in deicer solutions causes the most severe paste deterioration by forming non-cementitious magnesium silicate hydrate and brucite. Chloride in deicer solutions promotes decalcification of paste and alters ettringite to chloroaluminate. Calcium magnesium acetate (CMA) and magnesium acetate (Mg-acetate) produce the most deleterious effects on concrete, with calcium acetate (Ca-acetate) being much less severe.

Recent human-induced trophic change in the large and deep perialpine Lake Lucerne (Switzerland) compared to historical geochemical variations

This study investigates the sedimentological and geochemical changes that occurred during the last 2200 years in the meromictic Lake Lucerne (Switzerland), one of the largest freshwater lakes of Central Europe. The stable isotope composition (delta C-13 and delta O-18 values) of bulk carbonates is compared to changes in grain-size distribution (clay and silt fraction), natural trace element input (titanium and thorium concentrations), and organic material abundance (C-org, nitrogen and phosphorus) and composition (C/N ratios and hydrogen and oxygen indexes). A drop in carbonate accumulation and in the delta O-18 values of sediments between ca. AD 500 and 700 followed a large and consistent rise in chemical weathering, marked by increases in the silicate-clay fraction and in crustal element concentrations. During the following millennium, there was a long-term decreasing trend in the lithogenic trace element input and in the phosphorus loading, suggesting decreasing terrigeneous input from runoff water. The major sedimentological change over the studied period occurred after ca. AD 1800 with a significant increase in the erosion-driven silt-fraction and in the sedimentation rate. During the last century, human-induced increase in nutrient input to the lake highly enhanced the accumulation of organic matter in sediment. Changes in nutrients and oxygen conditions in the hypolimnion of Lake Lucerne during the eutrophication period (i.e., the last 40 years) highly modified the geochemical fluxes compared to the relatively stable oligotrophic conditions that prevailed during the previous 2000 years. Before the 19th century, climate driven meromixis had a limited impact on the organic matter flux to the sediments, but the accumulation of carbonate considerably decreased during periods of lower mechanical erosion rates and high chemical weathering rates. (C) 2012 Elsevier B.V. All rights reserved.

Durability Study of Type II Cements, MLR-71-03 and R-247, 1971

A study of type II cements at the Iowa State Highway Commission concluded that the amount of tricalcium aluminate in the cement appears to have an inverse effect on concrete durability. This conclusion agrees with the results of the Kansas Highway Department's study to determine the combination of cement and aggregate which would produce the best possible durability factor. This study is a result of the questions raised following the completion of the project at the Iowa State Highway Commission. This project is being conducted on a larger scale so. that more definite conclusions can be drawn. The purpose of this project is to determine if the amount of tricalcium aluminate in type II cements has an inverse effect on the durability of concrete.

Control of Concrete Deterioration Due to Trace Compounds in Deicers, Phase II, HR-299, 1989

This report presents results of research on ways to reduce the detrimental effects of sulfate-tainted rock salt deicers on portland cement concrete used for highway pavements. Repetitious experiments on the influence of fly ash on the mortar phase of concrete showed significant improvement in resistance to deicing brines is possible. Fifteen to twenty percent by weight of fly ash replacement for portland cement was found to provide optimum improvement. Fly ashes from five sources were evaluated and all were found to be equally beneficial. Preliminary results indicate the type of coarse aggregate also plays an important role in terms of concrete resistance to freeze-thaw in deicing brines. This was particularly true for a porous ferroan dolomite thought to be capable of reaction with the brine. In this case fly ash improved the concrete, but not enough for satisfactory performance. An intermediate response was with a porous limestone where undesirable results were observed without fly ash and adequate performance was realized when 15% fly ash was added. The best combination for making deicer-resistant concrete was found to be with a non-porous limestone. Performance in brines was found to be adequate without fly ash, but better when fly ash was included. Consideration was given to treating existing hardened concrete made with poor aggregate and no fly ash to extend pavement life in the presence of deicers, particularly at joints. Sodium silicate was found to improve freeze-thaw resistance of mortar and is a good candidate for field usage because of its low cost and ease of handling.

Time-Temperature Strength-Reaction Product Relationships in Lime-Bentonite-Water Mixtures, HR-111, 1965

The interrelation of curing time, curing temperature, strength, and reactions in lime-bentonite-water mixtures was examined. Samples were molded at constant density and moisture content and then cured for periods of from 1 to 56 days at constant temperatures that ranged from 5C to 60C. After the appropriate curing time the samples were tested for unconfined compressive strength. The broken samples were then analyzed by x-ray diffractometer and spectrophotometer to determine the identity of the reaction products present after each curing period. It was found that the strength gain of lime-clay mixtures cured at different temperatures is due to different phases of the complex reaction, lime & clay to CSH(gel) to CSH(II) to CSH(I) to tobermorite. The farther the reaction proceeds, the higher the strength. There was also evidence of lattice substitutions in the structure of the calcium silicate hydrates at curing temperatures of 50C and higher. No consistent relationship between time, temperature, strength, and the S/A ration of reaction products existed, but in order to achieve high strengths the apparent C/S ration had to be less than two. The curing temperature had an effect on the strength developed by a given amount of reacted silica in the cured lime-clay mixture, but at a given curing temperature the cured sample that had the largest amount of reacted silica gave the highest strength. Evidence was found to indicate that during the clay reaction some calcium is indeed adsorbed onto the clay structure rather than entering into a pozzolanic reaction. Finally, it was determined that it is possible to determine the amount of silica and alumina in lime-clay reaction products by spectrophotometric analysis with sufficient accuracy for comparison purposes. The spectrophotometric analysis techniques used during the investigation were simple and were not time consuming.

Effect of CA-Montmorillonite Expansion on X-Ray Diffraction Intensities, Progress Report, HR-111, 1966

The most abundant clay mineral group in Iowa soils is montmorillonite, most commonly calcium-saturated (Hanway et al, 1960). The calcium montmorillonite-water system was therefore selected for detailed X-ray study. Montmorillonite is unusual among minerals in that it has an expanding lattice in the c direction. That is, upon wetting with water, the individual silicate layers separate to allow entry of water, and the mineral expands. Characteristics of this expansion are readily studied by means of X-ray diffraction: the X-ray diffraction angle gives the average layer-to-layer "d001" spacing for any given moisture condition; the sharpness of the diffraction peak is a measure of uniformity of the d001 spacing; and the intensity of the peak relates to uniformity of the d001 spacing and in addition to the electron density distribution within the repeating elements. The latter is embodied in the "structure factor".

A Study of Curing Methods and Type II Cements on the Durability of Concrete, R-11-Z(1), 1969

A program of A (90 day moist room), B (14 day moist room) and C (7 day moist room and 7 day 50%_humidity) type curing for the R-11-Z program of durability of concrete using the automatic freeze and thaw machine (ASTM C-291) has been used in the Materials Department of the Iowa State Highway Commission since December 6, 1966. A summary of the results obtained from then until March 25, 1968, indicates that the B and C type curing are yielding very little valuable information. However, the A cure exhibits a wide range of durability factors and also groups the aggregates in an order which is related to the service record (there are definite exceptions. The biggest disadvantage to the A cure is the length of time that it takes to complete the test (90 day cure and 38 day test). The Kansas Highway Department has experimented with different cements and aggregates in order to determine which combination offers a concrete with the best durability factor possible. In an experimental test section of highway, concrete made with a Type II cement appeared to have better durability than others made with Type I cements. Because of this, a question has been raised at the Iowa State Highway Commission - Can concrete made with Type II cements, because of a lesser amount of tricalcium aluminate, yield better durability than concrete made with Type I cements?

Origin of CO2 and carbonate veins in mantle-derived xenoliths in the Pannonian Basin

The origin and evolution of CO2 inclusions and calcite veins in peridotite xenoliths of the Pannonian Basin, Hungary, were investigated by means of petrographic investigation and stable isotope analyses. The fluid inclusions recovered in paragenetic olivine and clinopyroxene belong to distinct populations: type A (texturally early) inclusions with regular shapes (often with negative crystal forms) forming intragranular trails, type B (texturally late) inclusions defining randomly oriented trails that reach grain boundaries Type B inclusions are often associated with silicate melt (type C) inclusions Stable carbon isotope compositions in inclusion-hosted CO2 were obtained by vacuum crushing followed by conventional dual inlet as well as continuous flow mass spectrometry in order to eliminate possible lab artifacts. Olivines, clino- and orthopyroxenes of the host peridotite have oxygen isotope compositions from 5.3 to 6.0 parts per thousand (relative to V-SMOW). without any relationship with xenolith texture. Some of the xenoliths contained calcite in various forms veins and infillings in silicate globules in veins, secondary carbonate veins filling cracks and metasomatic veins with diffuse margins The former two carbonate types have delta C-13 values around -13 parts per thousand (relative to V-PDB) and low Sr contents (<05 wt %), whereas the third type,veins with high-temperature metasomatic features have a delta C-13 value of -5 0 parts per thousand and high Sr contents up to 34 wt.% In spite of the mantle-like delta C-13 value and the unusually high Sr content typical for mantle-derived carbonate, trace element compositions have proven a crustal origin. This observation supports the conclusions of earlier studies that the carbonate melt droplets found on peridotite xenoliths in the alkaline basalts represent mobilized sedimentary carbonate. The large delta C-13 range and the C-12-enrichment in the carbonates can be attributed to devolanlization of the migrating carbonate or infiltration of surficial fluids containing C-12-rich dissolved carbon Carbon isotope compositions of inclusion-hosted CO2 range from -17 8 to -4.8 parts per thousand (relative to V-PDB) with no relation to the amount of CO2 released by vacuum crushing. Low-delta C-13 values measured by stepwise heating under vacuum suggest that the carbon component is pristine and not related to surficial contamination, and that primary mantle fluids with delta C-13 values around -5 parts per thousand were at least partly preserved in the xenoliths Tectonic reworking and heating by the basaltic magma resulted in partial CO2 release and local C-13-depletion. (C) 2010 Elsevier B V All rights reserved

Fluid geochemistry of the Acqui Terme-Visone geothermal area (Piemonte, Italy)

The main geothermal reservoir of Acqui Terme-Visone hosts Na-Cl waters, which are in chemical equilibrium at 120-130 degrees C with typical hydrothermal minerals including quartz, albite, K-feldspar, illite, chlorite (or smectite), anhydrite, calcite and an unspecified Ca-Al-silicate. In the Acqui Terme-Visone area, these geothermal waters ascend along zones of high vertical permeability and discharge at the surface almost undiluted or mixed with cold, shallow waters. To the SW of Acqui Terme, other ascending geothermal waters, either undiluted or mixed with low-salinity waters, enter relatively shallow secondary reservoirs, where they reequilibrate at 65-70 degrees C. Both chemical and isotopic data indicate that bacterial SO4 reduction affects all these waters, especially those discharged by the secondary reservoirs. Therefore, geothermal waters must get in contact with oil, acquiring the relatively oxidized organic substances needed by SO4-reducing bacteria. This oil-water interaction process deserves further investigations, for potential economic implications. (C) 2000 Elsevier Science Ltd. All rights reserved.

Surface modification of biomaterials for conjugation with human fetal osteoblasts.

Surface functionalization of hydroxyapatite (HA) and beta-tricalcium phosphate (TCP) bioceramics with chemical ligands containing a pyrrogallol moiety was developed to improve the adhesion of bone cell precursors to the biomaterials. Fast and biocompatible copper-free click reaction with azido-modified human fetal osteoblasts resulted in improved cell binding to both HA and TCP bioceramics, opening the way for using this methodology in the preparation of cell-engineered bone implants.