The effect of artisanal preservation methods on nutritional security of “Mukene” Rastrineobola argentea caught from Lakes Victoria and Kyoga in Uganda

The artisanal fish preservation methods in Uganda are characterized by extreme operating conditions. Consequently, vital nutritional components diminish in value and quantity which renders fish consumer nutritionally insecure. To establish the magnitude of nutritional loss, duplicate samples of Mukene Rastrineobola argentea were collected from Kiyindi landing site on L. Victoria and Moone landing site on L. Kyoga. Each set of duplicate samples was divided into five portions and kept on ice. For each preservation method a portion was processed into respective products at Food Bioscience and Agri-Business Laboratories aside from the control (fresh) sample. Both preserved and control samples were analysed for nutrient loss at Department of Chemistry, Makerere University using AOAC methods. The composition of fatty acids was determined by methanolysis gas chromatography and Mass spectrophotometry of the resultant methyl esters. The results indicate that nutrients of all preserved samples did not vary significantly from the control except for some fatty acids. The Eicosapentaenoic acid (EPA) in fresh samples declined from 6.72% to 1.08% in deep-fried samples constituting 83.93% nutrient loss. The sum ratio w3:w6 as well as EPA: DHA (Docosahexaenoic) ratio in fried samples also varied significantly (p<0.5) lower than 0.668 and 0.20 for the average of either preservation methods and experts recommended ratio respectively. Further research has been recommended to ascertain the causative factor, since Mukene frying is being promoted in the Great lakes region as alternative method to sun-drying. In conclusion, regular consumers of fried Mukene do not benefit much from the nutritional and health attributes of Omega 3 and 6.

La peche dans le fleuve Niger

The fish production of the River Niger can best be estimated from a country by country evaluation of the tonnage exported and that consumed locally. All exported and some locally consumed fish are preserved by smoking or sun drying, a process which entails a loss of weight. Coefficients to correct for this of between 2.6 to 4 have been calculated depending on the type of product. A further loss occurs due to handling and to insect attack, which may account for up to 40% of the production. Taking the above factors into account the productions estimated for the various countries of the Niger River basin are as follows: Guinea (3,600 t), Mali (90,000 t), Upper Volta and Ivory Coast (negligible), Niger (5,200 t), Dahomey (1,200 t), Nigeria (25,000 t), Cameroon (3,000 t). A total production of 128,000 t is, therefore, obtained for the basin as a whole, excluding the Kainji Reservoir. At this level of production, there have been no intimations of overfishing from any part of the basin, and there is unanimity that fishing could be intensified. On the basis of the estimates of existing production and local estimates of potential production it is possible that up to 200,000 t of fish could be produced annually from the basin as a whole.

Performance of thin film carbon materials and carbon nanotubes as cold cathodes

The field emissions from three different types of carbon films are studied using a Kiethly voltage-current source-measure unit under computer control. The three types of carbon films are : 1) a-C:H:N deposited using an inductively coupled rf PECVD process, where the N content in the films can be as high as 30 at %; 2) cathodic arc deposited tetrahedral amorphous carbon with embedded regions of carbon nanotube and anion structures and 3) unoriented carbon nanotube films on a porous substrate. The films are formed by filtering a solution of nanotubes dispersed in alcohol through the pores and drying.

The potential for thermal energy recovery from wastewater treatment works in Southern England

There is potential to extract energy from wastewater in a number of ways, including: kinetic energy using micro-hydro systems, chemical energy through the incineration of sludge, biomass energy from the biogas produced after anaerobic sludge digestion, and thermal energy as heat. This paper considers the last option and asks how much heat could be recovered under UK climatic conditions and can this heat be used effectively by wastewater treatment plants to reduce their carbon footprint? Four wastewater treatment sites in southern England are investigated and the available heat that can be recovered at those sites is quantified. Issues relating to the environmental, economic and practical constraints on how energy can be realistically recovered and utilised are discussed .The results show there is a definite possibility for thermal energy recovery with potential savings at some sites of up to 35,000 tonnes of total long-cycle carbon equivalent (fossil fuel) emissions per year being achievable. The paper also shows that the financial feasibility of three options for using the heat (either for district heating, sludge drying or thermophilic heating in sludge digestion processes) is highly dependant upon the current shadow price of carbon. Without the inclusion of the cost of carbon, the financial feasibility is significantly limited. An environmental constraint for the allowable discharge temperature of effluent after heat-extraction was found to be the major limitation to the amount of energy available for recovery. The paper establishes the true potential of thermal energy recovery from wastewater in English conditions and the economic feasibility of reducing the carbon footprint of wastewater treatment operations using this approach.

Design guidelines for granular particles in a conical centrifugal filter

Essential design criteria for successful drying of granular particles in a conical continuous centrifugal filter are developed in a dimensionless fashion. Four criteria are considered: minimum flow thickness (to ensure sliding bulk flow rather than particulate flow), desaturation position, output dryness and basket failure. The criteria are based on idealised physical models of the machine operation and are written explicitly as functions of the basket size lout, spin velocity Ω and input flow rate of powder Qp. The separation of sucrose crystals from liquid molasses is taken as a case study and the successful regime of potential operating points (lout, Ω) is plotted for a wide range of selected values of flow rate Qp. Analytical expressions are given for minimum and maximum values of the three independent parameters (lout, Ω, Qp) as a function of the slurry and basket properties. The viable operating regime for a conical centrifugal filter is thereby obtained as a function of the slurry and basket properties. © 2012 The Institution of Chemical Engineers.

Chemical nano-gardens: growth of salt nanowires from supramolecular self-assembly gels.

In this article, we examine the phenomenon of single-crystal halide salt wire growth at the surface of porous materials. We report the use of a single-step casting technique with a supramolecular self-assembly gel matrix that upon drying leads to the growth of single-crystal halide (e.g., NaCl, KCl, and KI) nanowires with diameters ~130-200 nm. We demonstrate their formation using electron microscopy and electron-dispersive X-ray spectroscopy, showing that the supramolecular gel stabilizes the growth of these wires by facilitating a diffusion-driven base growth mechanism. Critically, we show that standard non-supramolecular gels are unable to facilitate nanowire growth. We further show that these nanowires can be grown by seeding, forming nanocrystal gardens. This study helps understand the possible prefunctionalization of membranes to stimulate ion-specific filters or salt efflorescence suppressors, while also providing a novel route to nanomaterial growth.

Cement bentonite cutoff walls for polluted sites

Cement-bentonite (CB) cutoff walls have long been used to control ground water flow and contaminant migration at polluted sites. Hydraulic conductivity and unconfined compressive strength are two short-term properties often used by industry and owners in CB specification and are important parameters discussed in this paper. For polluted sites, long-term compatibility is also an important issue. These properties are coupled to a number of external factors including the mix design, construction sequence, presence/absence of contaminants at the site. Additional short-term properties for engineering assessment include the stressstrain characteristics in both drained and undrained shear in both with and without confinement as well as one-dimensional consolidation properties. Long term CB properties are affected by aging, reaction chemistry, drying, in situ stress state, and interaction with the polluted environment. © 2013 Taylor & Francis Group.

The dominant role of the solvent-water interface in water droplet templating of polymers

We investigate the formation of microstructured polymer networks known as Breath Figure templated structures created by the presence of water vapour over evaporating polymer solutions. We use a highly controlled experimental approach to examine this dynamic and non-equilibrium process to uniquely compare pure solvent systems with polymer solutions and demonstrate using a combination of optical microscopy, focused ion-beam milling and SEM analysis that the porous polymer microstructure is completely controlled by the interfacial forces that exist between the water droplet and the solvent until a final drying dilation of the imprints. Water droplet contact angles are the same in the presence or absence of polymer and are independent of size for droplets above 5 μm. The polymer acts a spectator that serves to trap water droplets present at the air interface, and to transfer their shape into the polymer film. For the smallest pores, however, there are unexpected variations in the contact angle with pore size that are consistent with a possible contribution from line tension at these smaller dimensions. © The Royal Society of Chemistry.

Effect of process parameters on the morphology and nanostructure of roll-to-roll printed P3HT:PCBM thin films for organic photovoltaics

Roll-to-roll (R2R) gravure exhibits significant advantages such as high precision and throughput for the printing of photoactive and conductive materials and the fabrication of flexible organic electronics such as organic photovoltaics (OPVs). Since the photoactive layer is the core of the OPV, it is important to investigate and finally control the process parameters and mechanisms that define the film morphology in a R2R process. The scope of this work is to study the effect of the R2R gravure printing and drying process on the nanomorphology and nanostructure of the photoactive P3HT:PCBM thin films printed on PEDOT:PSS electrodes towards the fabrication of indium tin oxide (ITO)-free flexible OPVs. In order to achieve this, P3HT:PCBM blends of different concentration were R2R printed under various speeds on the PEDOT:PSS layers. Due to the limited drying time during the rolling, an amount of solvent remains in the P3HT:PCBM films and the slow-drying process takes place which leads to the vertical and lateral phase separation, according to the Spectroscopic Ellipsometry and Atomic Force Microscopy analysis. The enhanced slow-drying leads to stronger phase separation, larger P3HT crystallites according to the Grazing Incidence X-Ray Diffraction data and to weaker mechanical response as it was shown by the nanoindentation creep. However, in the surface of the films the P3HT crystallization is controlled by the impinged hot air during the drying, where the more the drying time the larger the surface P3HT crystallites. The integration of the printed P3HT:PCBM and PEDOT:PSS layers in an OPV device underlined the feasibility of fabricating ITO-free flexible OPVs by R2R gravure processes. © 2013 Elsevier B.V.

Evolution of vertical phase separation in P3HT:PCBM thin films induced by thermal annealing

The achievement of the desirable morphology at the nanometer scale of bulk heterojunctions consisting of a conjugated polymer with fullerene derivatives is a prerequisite in order to optimize the power conversion efficiency of organic solar cells. The various experimental conditions such as the choice of solvent, drying rates and annealing have been found to significantly affect the blend morphology and the final performance of the photovoltaic device. In this work, we focus on the effects of post deposition thermal annealing at 140 °C on the blend morphology, the optical and structural properties of bulk heterojunctions that consist of poly(3-hexylthiophene) (P3HT) and a methanofullerene derivative (PCBM). The post thermal annealing modifies the distribution of the P3HT and the PCBM inside the blend films, as it has been found by Spectroscopic Ellipsometry studies in the visible to far-ultraviolet spectral range. Phase separation was identified by AFM and GIXRD as a result of a slow drying process which took place after the spin coating process. The increase of the annealing time resulted to a significant increase of the P3HT crystallinity at the top regions of the blend films. © 2011 Elsevier B.V. All rights reserved.

MEIOTIC CHROMOSOME BEHAVIOR IN FEMALE INTERSEXES OF ARTIFICIAL TRIPLOID TRANSPARENT-COLORED CRUCIAN CARP

Chromosome behavior in meiosis was studied by air-drying, C-banding and surface-spreading methods in female intersexes of artificial triploid transparent-colored crucian carp (Carassius auratus). Chromosome pairing and contraction were obviously asynchronous. The preferential pairing of two homologous chromosomes was the major pattern of chromosome pairing, and a few triple pairing, repeated pairing, telomer or centromere associating and multiple pairing were also observed in the pachytene cells. The metaphase I cells were mainly composed of univalents, bivalents and trivalents, as well as few of other multivalents, such as tetravalents, pentavalents, hexavalents and heptavalents, were also found in some metaphase I cells. The chromosome elements including uni-, bi-, tri- and other multivalents varied considerably among the metaphase I cells, and the associating patterns of multivalents were also diverse. Some 6 n and 12 n cells, in which premeiotic endomitosis occurred once or twice, were found at the prophase and first metaphase of meiosis, and the pairing and associating patterns were basically similar to that of the triploid cells.

Novel biodiesel production technology from soybean soapstock

This paper describes an attractive method to make biodiesel from soybean soapstock (SS). A novel recovery technology of acid oil (AO) from SS has been developed with only sulfuric acid solution under the ambient temperature (25 +/- 2 degrees C). After drying, AO contained 50.0% FFA, 15.5% TAG 6.9% DAG 3.1% MAG 0.8% water and other inert materials. The recovery yield of AO was about 97% (w/w) based on the total fatty acids of the SS. The acid oil could be directly converted into biodiesel at 95 degrees C in a pressurized reactor within 5 hours. Optimal esterification conditions were determined to be a weight ratio of 1 : 1.5 : 0.1 of AO/methanol/sulfuric acid. Higher reaction temperature helps to shorten the reaction time and requires less catalyst and methanol. Ester content of the biodiesel derived from AO through one-step acid catalyzed reaction is around 92%. After distillation, the purity of the biodiesel produced from AO is 97.6% which meets the Biodiesel Specification of Korea. The yield of purified biodiesel was 94% (w/w) based on the total fatty acids of the soapstock.

TDR和FDR测定黄绵土土壤含水量的标定

时域反射仪(TDR)与频率反射仪(FDR)是目前最为先进,并且最具有发展前途的土壤含水量测量仪器。有便利、快捷、准确的优点。介绍了6种基于TDR或FDR原理的仪器对黄绵土含水量进行试验标定的方法与结果。标定结果表明:仪器的测量值与烘干法的测量值之间有一定的差异,CS616和Trime-T3烘干法测定结果接近,但是其余的4种仪器测定值均高于烘干法测定值,在应用这些仪器测定土壤含水量时需要进行标定。

盐渍土的增湿剪切变形特性

盐渍土在浸水后由于盐分的溶解,对土体的强度产生较大的影响。在以往的研究中,主要以饱和与非饱和土体的强度比较来说明水对强度的影响,没有研究在部分浸水后土体的变形和强度的变化规律。针对这一点,在参考黄土增湿剪切方法的基础上研究了盐渍土的增湿剪切变形特性,探讨了垂直压力、干密度和剪应力水平对剪切变形量的影响规律。

干湿交替过程中土壤胀缩特征的实验研究

土壤胀缩是土壤在干燥、湿润交替变化过程中所表现出的土壤容积随含水量改变的现象。本文通过测定4种土壤脱水和吸水过程中的土柱高度和直径的变化,分析了胀缩过程中土壤容积与含水量的关系及土壤的胀缩特征。结果显示:三直线模型能够很好地拟合4种土壤的收缩、膨胀过程;土壤收缩、膨胀曲线各段的特征值均小于1,这说明土壤胀缩过程中土壤容积的变化速率小于含水量的变化速率;4种土壤胀缩过程中几何因子rs大于1而小于3,且收缩初期几何因子rs等于1,表明土壤的胀缩是各向异性的,并且在土壤收缩的最初阶段只有垂直收缩。