GA-based Optimization of a Fourth-order Sigma-delta Modulator for WLAN

Over-sampling sigma-delta analogue-to-digital converters (ADCs) are one of the key building blocks of state of the art wireless transceivers. In the sigma-delta modulator design the scaling coefficients determine the overall signal-to-noise ratio. Therefore, selecting the optimum value of the coefficient is very important. To this end, this paper addresses the design of a fourthorder multi-bit sigma-delta modulator for Wireless Local Area Networks (WLAN) receiver with feed-forward path and the optimum coefficients are selected using genetic algorithm (GA)- based search method. In particular, the proposed converter makes use of low-distortion swing suppression SDM architecture which is highly suitable for low oversampling ratios to attain high linearity over a wide bandwidth. The focus of this paper is the identification of the best coefficients suitable for the proposed topology as well as the optimization of a set of system parameters in order to achieve the desired signal-to-noise ratio. GA-based search engine is a stochastic search method which can find the optimum solution within the given constraints.

A New Gridding Technique for High Density Microarray Images Using Intensity Projection Profile of Best Sub Image

As the technologies for the fabrication of high quality microarray advances rapidly, quantification of microarray data becomes a major task. Gridding is the first step in the analysis of microarray images for locating the subarrays and individual spots within each subarray. For accurate gridding of high-density microarray images, in the presence of contamination and background noise, precise calculation of parameters is essential. This paper presents an accurate fully automatic gridding method for locating suarrays and individual spots using the intensity projection profile of the most suitable subimage. The method is capable of processing the image without any user intervention and does not demand any input parameters as many other commercial and academic packages. According to results obtained, the accuracy of our algorithm is between 95-100% for microarray images with coefficient of variation less than two. Experimental results show that the method is capable of gridding microarray images with irregular spots, varying surface intensity distribution and with more than 50% contamination

Sedimentology and Geochemistry of core sediments from the Ashtamudi estuary and the adjoining coastal plain,central Kerala,India

The evolution of coast through geological time scale is dependent on the transgression-regression event subsequent to the rise or fall of sea level. This event is accounted by investigation of the vertical sediment deposition patterns and their interrelationship for paleo-enviornmental reconstruction. Different methods like sedimentological (grain size and micro-morphological) and geochemical (elemental relationship) analyses as well as radiocarbon dating are generally used to decipher the sea level changes and paleoclimatic conditions of the Quaternary sediment sequence. For the Indian coast with a coastline length of about 7500 km, studies on geological and geomorphological signatures of sea level changes during the Quaternary were reported in general by researchers during the last two decades. However, for the southwest coast of India particularily Kerala which is famous for its coastal landforms comprising of estuaries, lagoons, backwaters, coastal plains, cliffs and barrier beaches, studies pertaining to the marine transgression-regression events in the southern region are limited. The Neendakara-Kayamkulam coastal stretch in central Kerala where the coast is manifested with shore parallel Kayamkulam Lagoon on one side and shore perpendicular Ashtamudi Estuary on the other side indicating existence of an uplifted prograded coastal margin followed by barrier beaches, backwater channels, ridge and runnel topography is an ideal site for studying such events. Hence the present study has been taken up in this context to address the gap area. The location for collection of core samples representing coastal plain, estuarylagoon and offshore regions have been identified based on published literature and available sedimentary records. The objectives of the research work are:  To study the lithological variations and depositional environments of sediment cores along the coastal plain, estuary-lagoon and offshore regions between Kollam and Kayamkulam in the central Kerala coast  To study the transportation and diagenetic history of sediments in the area  To investigate the geochemical characterization of sediments and to elucidate the source-sink relationship  To understand the marine transgression-regression events and to propose a conceptual model for the region The thesis comprises of 8 chapters. The first chapter embodies the preamble for the selection and significance of this research work. The study area is introduced with details on its physiographical, geological, geomorphological, rainfall and climate information. A review of literature, compiling the research on different aspects such as physico-chemical, geomorphological, tectonics, transgression-regression events are presented in the second chapter and they are broadly classified into three viz:- International, National and Kerala. The field data collection and laboratory analyses adopted in the research work are discussed in the third chapter. For collection of sediment core samples from the coastal plains, rotary drilling method was employed whereas for the estuary-lagoon and offshore locations the gravity/piston corer method was adopted. The collected subsurficial samples were analysed for texture, surface micro-texture, elemental analysis, XRD and radiocarbon dating techniques for age determination. The fourth chapter deals with the textural analysis of the core samples collected from various predefined locations of the study area. The result reveals that the Ashtamudi Estuary is composed of silty clay to clayey type of sediments whereas offshore cores are carpeted with silty clay to relict sand. Investigation of the source of sediments deposited in the coastal plain located on either side of the estuary indicates the dominance of terrigenous to marine origin in the southern region whereas it is predominantly of marine origin towards the north. Further the hydrodynamic conditions as well as the depositional enviornment of the sediment cores are elucidated based on statistical parameters that decipher the deposition pattern at various locations viz., coastal plain (open to closed basin), Ashtamudi Estuary (partially open to restricted estuary to closed basin) and offshore (open channel). The intensity of clay minerals is also discussed. From the results of radiocarbon dating the sediment depositional environments were deciphered.The results of the microtextural study of sediment samples (quartz grains) using Scanning Electron Microscope (SEM) are presented in the fifth chapter. These results throw light on the processes of transport and diagenetic history of the detrital sediments. Based on the lithological variations, selected quartz grains of different environments were also analysed. The study indicates that the southern coastal plain sediments were transported and deposited mechanically under fluvial environment followed by diagenesis under prolonged marine incursion. But in the case of the northern coastal plain, the sediments were transported and deposited under littoral environment indicating the dominance of marine incursion through mechanical as well as chemical processes. The quartz grains of the Ashtamudi Estuary indicate fluvial origin. The surface texture features of the offshore sediments suggest that the quartz grains are of littoral origin and represent the relict beach deposits. The geochemical characterisation of sediment cores based on geochemical classification, sediment maturity, palaeo-weathering and provenance in different environments are discussed in the sixth chapter. In the seventh chapter the integration of multiproxies data along with radiocarbon dates are presented and finally evolution and depositional history based on transgression–regression events is deciphered. The eighth chapter summarizes the major findings and conclusions of the study with recommendation for future work.

FEM based Virtual Prototyping and Design of Third Harmonic Excitation System for Low Voltage Brushless Alternators

Salient pole brushless alternators coupled to IC engines are extensively used as stand-by power supply units for meeting in- dustrial power demands. Design of such generators demands high power to weight ratio, high e ciency and low cost per KVA out- put. Moreover, the performance characteristics of such machines like voltage regulation and short circuit ratio (SCR) are critical when these machines are put into parallel operation and alterna- tors for critical applications like defence and aerospace demand very low harmonic content in the output voltage. While designing such alternators, accurate prediction of machine characteristics, including total harmonic distortion (THD) is essential to mini- mize development cost and time. Total harmonic distortion in the output voltage of alternators should be as low as possible especially when powering very sophis- ticated and critical applications. The output voltage waveform of a practical AC generator is replica of the space distribution of the ux density in the air gap and several factors such as shape of the rotor pole face, core saturation, slotting and style of coil disposition make the realization of a sinusoidal air gap ux wave impossible. These ux harmonics introduce undesirable e ects on the alternator performance like high neutral current due to triplen harmonics, voltage distortion, noise, vibration, excessive heating and also extra losses resulting in poor e ciency, which in turn necessitate de-rating of the machine especially when connected to non-linear loads. As an important control unit of brushless alternator, the excitation system and its dynamic performance has a direct impact on alternator's stability and reliability. The thesis explores design and implementation of an excitation i system utilizing third harmonic ux in the air gap of brushless al- ternators, using an additional auxiliary winding, wound for 1=3rd pole pitch, embedded into the stator slots and electrically iso- lated from the main winding. In the third harmonic excitation system, the combined e ect of two auxiliary windings, one with 2=3rd pitch and another third harmonic winding with 1=3rd pitch, are used to ensure good voltage regulation without an electronic automatic voltage regulator (AVR) and also reduces the total harmonic content in the output voltage, cost e ectively. The design of the third harmonic winding by analytic methods demands accurate calculation of third harmonic ux density in the air gap of the machine. However, precise estimation of the amplitude of third harmonic ux in the air gap of a machine by conventional design procedures is di cult due to complex geome- try of the machine and non-linear characteristics of the magnetic materials. As such, prediction of the eld parameters by conven- tional design methods is unreliable and hence virtual prototyping of the machine is done to enable accurate design of the third har- monic excitation system. In the design and development cycle of electrical machines, it is recognized that the use of analytical and experimental methods followed by expensive and in exible prototyping is time consum- ing and no longer cost e ective. Due to advancements in com- putational capabilities over recent years, nite element method (FEM) based virtual prototyping has become an attractive al- ternative to well established semi-analytical and empirical design methods as well as to the still popular trial and error approach followed by the costly and time consuming prototyping. Hence, by virtually prototyping the alternator using FEM, the important performance characteristics of the machine are predicted. Design of third harmonic excitation system is done with the help of results obtained from virtual prototype of the machine. Third harmonic excitation (THE) system is implemented in a 45 KVA ii experimental machine and experiments are conducted to validate the simulation results. Simulation and experimental results show that by utilizing third harmonic ux in the air gap of the ma- chine for excitation purposes during loaded conditions, triplen harmonic content in the output phase voltage is signi cantly re- duced. The prototype machine with third harmonic excitation system designed and developed based on FEM analysis proved to be economical due to its simplicity and has the added advan- tage of reduced harmonics in the output phase voltage.

A Study of Single Stage Semi‐Dry Anaerobic Digestion of Organic Fraction of Municipal Solid Waste

Solid waste generation is a natural consequence of human activity and is increasing along with population growth, urbanization and industrialization. Improper disposal of the huge amount of solid waste seriously affects the environment and contributes to climate change by the release of greenhouse gases. Practicing anaerobic digestion (AD) for the organic fraction of municipal solid waste (OFMSW) can reduce emissions to environment and thereby alleviate the environmental problems together with production of biogas, an energy source, and digestate, a soil amendment. The amenability of substrate for biogasification varies from substrate to substrate and different environmental and operating conditions such as pH, temperature, type and quality of substrate, mixing, retention time etc. Therefore, the purpose of this research work is to develop feasible semi-dry anaerobic digestion process for the treatment of OFMSW from Kerala, India for potential energy recovery and sustainable waste management. This study was carried out in three phases in order to reach the research purpose. In the first phase, batch study of anaerobic digestion of OFMSW was carried out for 100 days at 32°C (mesophilic digestion) for varying substrate concentrations. The aim of this study was to obtain the optimal conditions for biogas production using response surface methodology (RSM). The parameters studied were initial pH, substrate concentration and total organic carbon (TOC). The experimental results showed that the linear model terms of initial pH and substrate concentration and the quadratic model terms of the substrate concentration and TOC had significant individual effect (p < 0.05) on biogas yield. However, there was no interactive effect between these variables (p > 0.05). The optimum conditions for maximizing the biogas yield were a substrate concentration of 99 g/l, an initial pH of 6.5 and TOC of 20.32 g/l. AD of OFMSW with optimized substrate concentration of 99 g/l [Total Solid (TS)-10.5%] is a semi-dry digestion system .Under the optimized condition, the maximum biogas yield was 53.4 L/kg VS (volatile solid).. In the second phase, semi-dry anaerobic digestion of organic solid wastes was conducted for 45 days in a lab-scale batch experiment for substrate concentration of 100 g/l (TS-11.2%) for investigating the start-up performances under thermophilic condition (50°C). The performance of the reactor was evaluated by measuring the daily biogas production and calculating the degradation of total solids and the total volatile solids. The biogas yield at the end of the digestion was 52.9 L/kg VS for the substrate concentration of 100 g/l. About 66.7% of volatile solid degradation was obtained during the digestion. A first order model based on the availability of substrate as the limiting factor was used to perform the kinetic studies of batch anaerobic digestion system. The value of reaction rate constant, k, obtained was 0.0249 day-1. A laboratory bench scale reactor with a capacity of 36.8 litres was designed and fabricated to carry out the continuous anaerobic digestion of OFMSW in the third phase. The purpose of this study was to evaluate the performance of the digester at total solid concentration of 12% (semi-dry) under mesophlic condition (32°C). The digester was operated with different organic loading rates (OLRs) and constant retention time. The performance of the reactor was evaluated using parameters such as pH, volatile fatty acid (VFA), alkalinity, chemical oxygen demand (COD), TOC and ammonia-N as well as biogas yield. During the reactor’s start-up period, the process is stable and there is no inhibition occurred and the average biogas production was 14.7 L/day. The reactor was fed in continuous mode with different OLRs (3.1,4.2 and 5.65 kg VS/m3/d) at constant retention time of 30 days. The highest volatile solid degradation of 65.9%, with specific biogas production of 368 L/kg VS fed was achieved with OLR of 3.1 kg VS/m3/d. Modelling and simulation of anaerobic digestion of OFMSW in continuous operation is done using adapted Anaerobic Digestion Model No 1 (ADM1).The proposed model, which has 34 dynamic state variables, considers both biochemical and physicochemical processes and contains several inhibition factors including three gas components. The number of processes considered is 28. The model is implemented in Matlab® version 7.11.0.584(R2010b). The model based on adapted ADM1 was tested to simulate the behaviour of a bioreactor for the mesophilic anaerobic digestion of OFMSW at OLR of 3.1 kg VS/m3/d. ADM1 showed acceptable simulating results.

Degrees of Free Word-Order and Freely Rewriting Restarting Automata

In natural languages with a high degree of word-order freedom syntactic phenomena like dependencies (subordinations) or valencies do not depend on the word-order (or on the individual positions of the individual words). This means that some permutations of sentences of these languages are in some (important) sense syntactically equivalent. Here we study this phenomenon in a formal way. Various types of j-monotonicity for restarting automata can serve as parameters for the degree of word-order freedom and for the complexity of word-order in sentences (languages). Here we combine two types of parameters on computations of restarting automata: 1. the degree of j-monotonicity, and 2. the number of rewrites per cycle. We study these notions formally in order to obtain an adequate tool for modelling and comparing formal descriptions of (natural) languages with different degrees of word-order freedom and word-order complexity.

Bayes quadratic unbiased estimator of spatial covariance parameters

This work presents Bayes invariant quadratic unbiased estimator, for short BAIQUE. Bayesian approach is used here to estimate the covariance functions of the regionalized variables which appear in the spatial covariance structure in mixed linear model. Firstly a brief review of spatial process, variance covariance components structure and Bayesian inference is given, since this project deals with these concepts. Then the linear equations model corresponding to BAIQUE in the general case is formulated. That Bayes estimator of variance components with too many unknown parameters is complicated to be solved analytically. Hence, in order to facilitate the handling with this system, BAIQUE of spatial covariance model with two parameters is considered. Bayesian estimation arises as a solution of a linear equations system which requires the linearity of the covariance functions in the parameters. Here the availability of prior information on the parameters is assumed. This information includes apriori distribution functions which enable to find the first and the second moments matrix. The Bayesian estimation suggested here depends only on the second moment of the prior distribution. The estimation appears as a quadratic form y'Ay , where y is the vector of filtered data observations. This quadratic estimator is used to estimate the linear function of unknown variance components. The matrix A of BAIQUE plays an important role. If such a symmetrical matrix exists, then Bayes risk becomes minimal and the unbiasedness conditions are fulfilled. Therefore, the symmetry of this matrix is elaborated in this work. Through dealing with the infinite series of matrices, a representation of the matrix A is obtained which shows the symmetry of A. In this context, the largest singular value of the decomposed matrix of the infinite series is considered to deal with the convergence condition and also it is connected with Gerschgorin Discs and Poincare theorem. Then the BAIQUE model for some experimental designs is computed and compared. The comparison deals with different aspects, such as the influence of the position of the design points in a fixed interval. The designs that are considered are those with their points distributed in the interval [0, 1]. These experimental structures are compared with respect to the Bayes risk and norms of the matrices corresponding to distances, covariance structures and matrices which have to satisfy the convergence condition. Also different types of the regression functions and distance measurements are handled. The influence of scaling on the design points is studied, moreover, the influence of the covariance structure on the best design is investigated and different covariance structures are considered. Finally, BAIQUE is applied for real data. The corresponding outcomes are compared with the results of other methods for the same data. Thereby, the special BAIQUE, which estimates the general variance of the data, achieves a very close result to the classical empirical variance.

Einfluß der Gewässerversauerung auf Hyporheos und Bryorheos: Untersuchungen an zwei Waldbächen im Westharz

Im Rahmen der Fallstudie Harz sollte an der Schnittstelle zwischen Grundlagenforschung und angewandter Forschung ein Beitrag zur Klärung der Frage geleistet werden, inwieweit zwei Zuläufe der Sösetalsperre im Westharz versauert bzw. versauerungsgefährdet sind; aus diesem Stausee wird Trinkwasser für mehrere Gemeinden in Norddeutschland gewonnen. Die Belastung des fast vollständig bewaldeten Einzugsgebiets der Sösetalsperre mit luftbürtigen Schadstoffen (Saurer Regen) zählte zu den höchsten in Mitteleuropa. An jeweils drei Untersuchungsstellen der beiden Bäche Alte Riefensbeek (R1 bis R3) und Große Söse (S1 bis S3) wurden zwischen März 1987 und November 1988 Proben aus Moospolstern und dem hyporheischen Interstitial entnommen und physikalisch, chemisch und biologisch untersucht. Ergänzend wurden Wasserproben zwischen März 1986 und Oktober 1991 sowie vom April 1998 ebenso wie qualitative Fänge von Makroinvertebraten zwischen November 1986 und Juli 1990 sowie vom April 1998 ausgewertet. Die Analyse der tierischen Besiedlung der Moos- und Interstitialproben beschränkte sich auf die taxonomischen Gruppen Turbellaria (Strudelwürmer), Mollusca (Weichtiere), Amphipoda (Flohkrebse), Ephemeroptera (Eintagsfliegen), Plecoptera (Steinfliegen), Heteroptera (Wanzen), Megaloptera (Schlammfliegen), Coleoptera (Käfer), Trichoptera (Köcherfliegen) und Diptera (Zweiflügler). Der Grundsatz, daß normalverteilte und nicht normalverteilte Daten statistisch unterschiedlich behandelt werden müssen, wurde konsequent angewandt. Am Beispiel der Choriotopstruktur wurde gezeigt, daß die Auswahl des Analyseverfahrens das Ergebnis der ökologischen Interpretation multivariater statistischer Auswertung beeinflußt. Die Daten der Korngrößen-Verteilung wurden vergleichend einer univariaten und einer multivariaten statistischen Analyse unterworfen. Mit dem univariaten Verfahren wurden die Gradienten der ökologisch relevanten Korngrößen-Parameter eher erkannt als mit dem multivariaten Verfahren. Die Auswirkungen von Gewässerversauerung sowie anderer Umweltfaktoren (insgesamt 42 Faktoren) auf die Lebensgemeinschaften wurden anhand der Parameter Artenzahl, Besiedlungsdichte, Körpergröße und Biomasse untersucht. Abundanz, Biomasse und Körpergröße sowie die Umweltfaktoren wurden auf einem horizontalen Gradienten, d.h. im Längslauf der Bäche, und auf einem vertikalen Gradienten, d.h. fließende Welle / Bryorheon / Benthon versus Hyporheon, untersucht. Es wurde ein terminologisches System für die Kompartimente in der Fließgewässer-Aue vorgeschlagen, das in sich einheitlich ist. Es wurde ein neuer Moos-Vitalitätsindex für die Moospolster vorgestellt. Es wurden Bestimmungsschlüssel für die Larven der Chloroperlidae (Steinfliegen-Familie) und der Empididae (Tanzfliegen) in den beiden Harzbächen entwickelt. Die untersuchten Bachstrecken waren frei von Abwasserbelastung. An zwei Stellen wurde Wasser für einen Forellenteich ausgeleitet. Abgesehen von zwei meterhohen Abstürzen in der Großen Söse waren wasserbauliche Veränderungen ohne große Bedeutung. Das Abfluß-Regime war insofern nicht mehr natürlich, als beide Bäche in das System der bergbaulichen Bewässerungsgräben des Oberharzes eingebunden sind. Die Söse hatte ein F-nivopluviales Abfluß-Regime, der abflußreichste Doppelmonat war der März / April, die Unregelmäßigkeit des Abfluß-Regimes war sehr hoch, die Vorhersagbarkeit sehr niedrig, die monatlichen Abfluß-Maxima wiesen eine sehr geringe Konstanz auf. Der Zeitraum der biologischen Probenahme wurde von überdurchschnittlich vielen Tagen mit mäßig erhöhten Abflüssen geprägt, sehr große Hochwasser-Wellen fehlten aber. Die Abfluß-Dynamik wurde statistisch beschrieben. Das hydraulische Regime wurde anhand der Meßgrößen Fließgeschwindigkeit, Fließkraft und FROUDE-Zahl dargestellt. Der Zusammenhang zwischen Abfluß und Fließgeschwindigkeit auf der einen Seite und der Korngrößen-Verteilung auf der anderen Seite wurde statistisch untersucht, ebenfalls zwischen dem Abfluß und dem Kohlenstoff- und Stickstoff-Gehalt der Feinstpartikel sowie dem Wasserchemismus. In den Phasen ohne Hochwasser hatte das Hyporheal die Funktion einer Senke für Feinstkörner. Das Bachbett der Alten Riefensbeek war stabiler als das der Großen Söse. Insgesamt gesehen war das hyporheische Sediment in den quellnahen Abschnitten grobkörniger und auf den quellfernen Strecken feinkörniger. Der prozentuale Anteil der Feinstkörner im Hyporheal und Benthal nahm aber im Längslauf der Bäche ab. Dies ist ungewöhnlich, konnte aber nicht plausibel mit geologischen und hydrologischen Meßgrößen erklärt werden. Beide Bäche waren sommerkalt. Der Einfluß der Wassertemperatur auf die Larvalentwicklung wurde beispielhaft an den Taxa Baetis spp. und Leuctra gr. inermis untersucht. Es gab eine Tendenz, daß der Kohlenstoff- und Stickstoff-Gehalt der Feinstpartikel vom Benthal in das Hyporheal anstieg. Dies war ein weiterer Hinweis darauf, daß das Hyporheal die Funktion einer Senke und Vorratskammer für Nährstoffe hat. Der Zusammenhang zwischen partikulärer und gelöster Kohlenstoff-Fraktion wurde diskutiert. Im Hyporheon war die Nitrifikation nicht stärker als in der fließenden Welle. Es gab Hinweise, daß die sauren pH-Werte in der Großen Söse die Nitrifikation hemmten. Die Valenzen der Moos- und Tier-Taxa bezüglich Fließgeschwindigkeit, pH-Wert, Alkalinität sowie der Gehalte von Sauerstoff, Calcium, Magnesium, Kalium und Natrium wurden zusammengestellt. Das hyporheische Sediment war sehr grob und hatte eine hohe Porosität. Der Austausch zwischen fließender Welle und hyporheischem Wasser konnte deshalb sehr schnell erfolgen, es gab keine intergranulare Sprungschicht, die physikalischen und chemischen Tiefengradienten waren in den meisten Fällen gar nicht ausgeprägt oder nur sehr flach. Die Wassertemperatur des Freiwassers unterschied sich nicht signifikant von derjenigen im hyporheischen Wasser. Es gab -- von wenigen Ausnahmen bei pH-Wert, Leitfähigkeit und Sauerstoffgehalt abgesehen -- keine signifikanten Unterschiede zwischen dem Wasserchemismus der fließenden Welle und dem des Hyporheals. Die physikalischen und chemischen Voraussetzungen für die Refugialfunktion des Hyporheons waren deshalb für versauerungsempfindliche Taxa nicht gegeben. In der Tiefenverteilung der untersuchten Tiergruppen im Hyporheal lag das Maximum der Abundanz bzw. Biomasse häufiger in 10 cm als in 30 cm Tiefe. Daraus läßt sich aber keine allgemeine Gesetzmäßigkeit ableiten. Es wurde durchgehend die Definition angewendet, daß die Gewässerversauerung durch den Verlust an Pufferkapazität charakterisiert ist. Saure Gewässer können, müssen aber nicht versauert sein; versauerte Gewässer können, müssen aber nicht saures Wasser haben. Maßstab für das Pufferungsvermögen eines Gewässers ist nicht der pH-Wert, sondern sind die Alkalinität und andere chemische Versauerungsparameter. Der pH-Wert war auch operativ nicht als Indikator für Gewässerversauerung anwendbar. Die chemische Qualität des Bachwassers der Großen Söse entsprach aufgrund der Versauerung nicht den umweltrechtlichen Vorgaben bezüglich der Parameter pH-Wert, Aluminium, Eisen und Mangan, bzgl. Zink galt dies nur an S1. In der Alten Riefensbeek genügte das Hyporheal-Wasser in 30 cm Tiefe an R2 bzgl. des Sauerstoff-Gehalts nicht den umweltrechtlichen Anforderungen. Nur im Freiwasser an R1 genügten die Ammonium-Werte den Vorgaben der EG-Fischgewässer-Richtlinie, der Grenzwert wurde an allen anderen Meßstellen und Entnahmetiefen überschritten. Das BSB-Regime in allen Entnahmetiefen an R2, im Freiwasser an R3 und S1, im Hyporheal an R1 sowie in 30 cm Tiefe an R3 genügte nicht den Anforderungen der Fischgewässer-Richtlinie. Der Grenzwert für Gesamt-Phosphor wurde an S3 überschritten. In der Großen Söse war der Aluminium-Gehalt so hoch, daß anorganisches und organisches Aluminium unterschieden werden konnten. Besonders hohe Gehalte an toxischem anorganischen Aluminium wurden an Tagen mit Spitzen-Abflüssen und Versauerungsschüben gemessen. Erst die Ermittlung verschiedener chemischer Versauerungsparameter zeigte, daß auch die alkalischen Probestellen R2 und R3 mindestens versauerungsempfindlich waren. Die Messung bzw. Berechnung von chemischen Versauerungsparametern sollte deshalb zum Routineprogramm bei der Untersuchung von Gewässerversauerung gehören. Zu Beginn des Untersuchungsprogramms war angenommen worden, daß die mittleren und unteren Abschnitte der Alten Riefensbeek unversauert sind. Dieser Ansatz des Untersuchungsprogramms, einen unversauerten Referenzbach (Alte Riefensbeek) mit einem versauerten Bach (Große Söse) zu vergleichen, mußte nach der Berechnung von chemischen Versauerungsindikatoren sowie der Analyse der Abundanz- und Biomasse-Werte modifiziert werden. Es gab einen Versauerungsgradienten entlang der Probestellen: R1 (unversauert) R2 und R3 (versauerungsempfindlich bis episodisch leicht versauert) S2 und S3 (dauerhaft versauert) S1 (dauerhaft stark versauert). An S1 war das Hydrogencarbonat-Puffersystem vollständig, an S2 und S3 zeitweise ausgefallen. Die Versauerungslage an R2 und R3 war also schlechter als vorausgesehen. Unterschiede im Versauerungsgrad zwischen den Meßstellen waren nicht so sehr in unterschiedlichen Eintragsraten von versauernden Stoffen aus der Luft begründet, sondern in unterschiedlichen Grundgesteinen mit unterschiedlichem Puffervermögen. Der Anteil der verschiedenen sauren Anionen an der Versauerung wurde untersucht, die chemischen Versauerungsmechanismen wurden mit Hilfe von Ionenbilanzen und verschiedenen Versauerungsquotienten analysiert. Die beiden untersuchten Bäche waren von anthropogener Versauerung betroffen. Dabei spielte die Schwefel-Deposition (Sulfat) eine größere Rolle als die Stickstoff-Deposition (Nitrat). Die Probestelle S1 war immer schon in unbekanntem Maß natürlich sauer. Dieser natürlich saure Zustand wurde von der hinzugekommenen anthropogenen Versauerung bei weitem überragt. Die wenigen gewässerökologischen Daten, die im Wassereinzugsgebiet der Söse vor 1986 gewonnen wurden, deuten darauf hin, daß die Versauerung in den 70er und in der ersten Hälfte der 80er Jahre vom Boden und Gestein in die Bäche durchgeschlagen war. Dieser Versauerungsprozeß begann vermutlich vor 1973 in den Quellen auf dem Acker-Bruchberg und bewegte sich im Laufe der Jahre immer weiter talwärts in Richtung Trinkwasser-Talsperre. Der Mangel an (historischen) freilandökologischen Grundlagendaten war nicht nur im Untersuchungsgebiet, sondern ist allgemein in der Versauerungsforschung ein Problem. Wenn sich das Vorkommen von nah verwandten Arten (weitgehend) ausschließt, kann dies an der Versauerung liegen, z.B. war die Alte Riefensbeek ein Gammarus-Bach, die Große Söse ein Niphargus-Bach; dieses muß aber nicht an der Versauerung liegen, z.B. fehlte Habroleptoides confusa im Hyporheos an R3, Habrophlebia lauta hatte dagegen ihr Abundanz- und Biomasse-Maximum an R3. Zugleich lag das Maximum des prozentualen Anteils von Grobsand an R3, eine mögliche Ursache für diese interspezifische Konkurrenz. Die biologische Indikation von Gewässerversauerung mit Hilfe der Säurezustandsklassen funktionierte nicht in den beiden Harzbächen. Es wurde deshalb ein biologischer Versauerungsindex vorgeschlagen; dieser wurde nicht am pH-Wert kalibriert, sondern an der chemischen Versauerungslage, gekennzeichnet durch die Alkalinität und andere chemische Meßgrößen der Versauerung. Dafür wurden aufgrund der qualitativen und quantitativen Daten die häufigeren Taxa in die vier Klassen deutlich versauerungsempfindlich, mäßig versauerungsempfindlich, mäßig versauerungstolerant und deutlich versauerungstolerant eingeteilt. Es reicht nicht aus, die biologischen Folgen von Gewässerversauerung sowie Veränderungen in der Nährstoff-Verfügbarkeit und im sonstigen Wasserchemismus nur anhand der Artenzahl oder des Artenspektrums abzuschätzen. Vielmehr müssen quantitative Methoden wie die Ermittlung der Abundanzen angewandt werden, um anthropogene und natürliche Störungen des Ökosystems zu erfassen. Es wurde eine Strategie für die behördliche Gewässergüteüberwachung von Bachoberläufen vorgeschlagen, die flächendeckend die Versauerungsgefährdung erfassen kann. Die Auswirkungen der zeitlichen Dynamik des Versauerungschemismus wurden am Beispiel des versauerungsempfindlichen Taxons Baetis spp. (Eintagsfliegen) dargestellt. An S2 und S3 kam es zu starken Versauerungsschüben. Baetis konnte sich nicht ganzjährig halten, sondern nur in versauerungsarmen Phasen im Sommer und im Herbst; es gab einen Besiedlungskreislauf aus Ausrottungs- und Wiederbesiedlungsphasen. Die temporäre Population von Baetis an S2 und S3 bestand nur aus ersten Larvenstadien. Die Probestellen wurden auf horizontalen Gradienten der Umweltfaktoren angeordnet. Bei einigen Parametern gab es keinen Gradienten (z.B. Sauerstoff-Gehalt), bei anderen Parametern waren die Meßstellen auf sehr flachen Gradienten angeordnet (z.B. C:N-Quotient der Feinstkörner), bei den restlichen Meßgrößen waren die Gradienten sehr deutlich (z.B. Alkalinität). Bei den Längsgradienten von Abundanz und Biomasse waren alle Möglichkeiten vertreten: Zunahme (z.B. Leuctra pseudosignifera), Abnahme (z.B. Gammarus pulex), Maximum an der mittleren Probestelle (z.B. Leuctra pseudocingulata) und kein signifikanter Trend (z.B. Nemoura spp.). Abundanz und Biomasse zahlreicher taxonomischer Einheiten hatten ihr Maximum im Längslauf an den quellnächsten Probestellen R1 und S1, z.B. Protonemura spp. und Plectrocnemia spp. Die Lebensgemeinschaften an R1 und S1 waren allerdings völlig unterschiedlich zusammengesetzt. Die häufig vertretene Annahme, versauerte Gewässer seien biologisch tot, ist falsch. Unter Anwendung des 3. biozönotischen Grundprinzips wurde das Maximum von Abundanz und Biomasse in den quellnahen Abschnitten mit dem eustatistischen (stabilen) Regime von Wassertemperatur, Abfluß und Protonen-Gehalt, in der Alten Riefensbeek auch von Alkalinität und ALMER-Relation erklärt. Aufgrund der natürlichen und anthropogenen Störungen war im Längslauf der untersuchten Bäche keine natürliche biozönotische Gliederung des Artenbestands erkennbar. Die Korrelationsberechnungen zwischen den Umweltfaktoren und der Taxazahl ergaben, daß in erster Linie versauerungsrelevante Parameter -- Gehalte saurer Anionen, basischer Kationen und von Metallen, Alkalinität usw. -- die höchsten Korrelationskoeffizienten mit der Taxa-Zahl hatten; unter den natürlichen Meßgrößen zählten nur die Gehalte von DOC und TIC sowie der Anteil der Sande zu der Gruppe mit den höchsten Korrelationskoeffizienten. Die Korrelationsberechnungen zwischen den Umweltfaktoren und den Abundanzen ergab dagegen, daß die quantitative Zusammensetzung der Lebensgemeinschaft nicht nur durch die anthropogene Gewässerversauerung, sondern mindestens genauso durch einige natürliche Meßgrößen beeinflußt wurde. Es gab in den Harzbächen keinen ökologischen Superfaktor, der die quantitative Zusammensetzung der Lebensgemeinschaft überwiegend bestimmte. Auch die Meßgrößen der anthropogenen Gewässerversauerung waren nicht solch ein Superfaktor. Einen ähnlich hohen Einfluß auf die quantitative Zusammensetzung der Lebensgemeinschaft hatten die geologisch bestimmten Umweltfaktoren Leitfähigkeit und TIC-Gehalt, der von der Landnutzung bestimmte DOC-Gehalt sowie der Chlorid-Gehalt, der geologisch, möglicherweise aber auch durch den Eintrag von Straßensalz bestimmt wird. Die Mischung von anthropogenen und natürlichen Faktoren wurde in einem Modell der Wirkung von abiotischen Faktoren auf Bryorheos und Hyporheos dargestellt. Als Beispiel für die zeitliche Nutzung ökologischer Nischen wurde die Verteilung der Larven und Adulten der Dryopidae (Hakenkäfer) im Hyporheos und Bryorheos untersucht. Die Larven wurden vorzugsweise im Hyporheon, die Adulten im Bryorheon angetroffen. Die untersuchten Taxa wurden in die Varianten bryorheobiont, bryorheophil, bryorheotolerant, bryorheoxen und bryorheophob bzw. hyporheobiont, hyporheophil, hyporheotolerant, hyporheoxen und hyporheophob eingeteilt, um ihre räumliche Nutzung ökologischer Nischen zu beschreiben. Die gängige Lehrmeinung, daß das Hyporheon die Kinderstube benthaler Makroinvertebraten ist, konnte für zahlreiche Taxa bestätigt werden (z.B. Habrophlebia lauta). Für die bryorheophilen Taxa (z.B. Gammarus pulex und Baetis spp.) trifft diese Lehrmeinung in den beiden Harzbächen nicht zu. Vielmehr übernimmt das Bryorheon die Funktion einer Kinderstube. Die Larven von Plectrocnemia conspersa / geniculata sowie von Baetis spp. und Amphinemura spp. / Protonemura spp. neben Gammarus pulex zeigten eine Habitatbindung, die erstgenannte Gattung an das Hyporheal, die letztgenannten 3 Taxa an untergetauchte Moospolster (Bryorheal). Die Idee von der Funktion des Hyporheals als Kinderstube der Larven und Jungtiere, als Schutzraum gegen die Verdriftung durch Strömung und vor Fraßdruck durch Räuber sowie als Ort hohen Nahrungsangebots mußte für die letztgenannten 3 Taxa abgelehnt werden. Für sie übernahm das Bryorheal diese Aufgaben. Zwar waren die beiden Bäche oligotroph und die Nahrungsqualität der Feinstkörner im Hyporheal war niedrig. Die Abundanz- und Biomasse-Werte im Bryorheos und Hyporheos gehörten aber zu den weltweit höchsten. Es wurde das Paradoxon diskutiert, daß im Hyporheon der beiden Bäche Diatomeen-Rasen gefunden wurden, obwohl das Hyporheon lichtlos sein soll. Das Hyporheon wurde als ein Ökoton zwischen Benthon / Rheon und Stygon angesehen. Es wurden vier Haupttypen des Hyporheons beschrieben. Wegen des sehr unterschiedlichen Charakters des Hyporheons in verschiedenen Fließgewässern gibt es keinen einheitlichen Satz von abiotischen und biotischen Faktoren, mit denen das Hyporheon vom Benthon und Stygon abgegrenzt werden kann. In den beiden Harzbächen ähnelte das Hyporheon mehr dem Benthon als dem Stygon. Es konnte nicht anhand der chemischen Meßgrößen vom Benthon abgegrenzt werden, sondern anhand der physikalischen Meßgrößen Trübung und der Anteile von Feinsand und Schluffe/Tone sowie anhand der biologischen Parameter Summen-Abundanz und Summen-Biomasse. Aus der Typologie des Hyporheons folgt, daß ein bestimmtes Hyporheon nicht alle in der Literatur beschriebenen Funktionen innerhalb der Fließgewässer-Aue übernehmen kann. Es wurde ein Schema entwickelt, mit dem sich die optimale Liste der Parameter für die Untersuchung eines bestimmten Hyporheons auswählen läßt. Der Tendenz in der Fließgewässer-Ökologie, immer neue Konzepte zu entwickeln, die allgemeingültig sein sollen, wurde das Konzept vom individuellen Charakter von Fließgewässer-Ökosystemen entgegengestellt.

Determination of yield and quality parameters of energy crops applying laboratory and field spectroscopy

A real-time analysis of renewable energy sources, such as arable crops, is of great importance with regard to an optimised process management, since aspects of ecology and biodiversity are considered in crop production in order to provide a sustainable energy supply by biomass. This study was undertaken to explore the potential of spectroscopic measurement procedures for the prediction of potassium (K), chloride (Cl), and phosphate (P), of dry matter (DM) yield, metabolisable energy (ME), ash and crude fibre contents (ash, CF), crude lipid (EE), nitrate free extracts (NfE) as well as of crude protein (CP) and nitrogen (N), respectively in pretreated samples and undisturbed crops. Three experiments were conducted, one in a laboratory using near infrared reflectance spectroscopy (NIRS) and two field spectroscopic experiments. Laboratory NIRS measurements were conducted to evaluate to what extent a prediction of quality parameters is possible examining press cakes characterised by a wide heterogeneity of their parent material. 210 samples were analysed subsequent to a mechanical dehydration using a screw press. Press cakes serve as solid fuel for thermal conversion. Field spectroscopic measurements were carried out with regard to further technical development using different field grown crops. A one year lasting experiment over a binary mixture of grass and red clover examined the impact of different degrees of sky cover on prediction accuracies of distinct plant parameters. Furthermore, an artificial light source was used in order to evaluate to what extent such a light source is able to minimise cloud effects on prediction accuracies. A three years lasting experiment with maize was conducted in order to evaluate the potential of off-nadir measurements inside a canopy to predict different quality parameters in total biomass and DM yield using one sensor for a potential on-the-go application. This approach implements a measurement of the plants in 50 cm segments, since a sensor adjusted sideways is not able to record the entire plant height. Calibration results obtained by nadir top-of-canopy reflectance measurements were compared to calibration results obtained by off-nadir measurements. Results of all experiments approve the applicability of spectroscopic measurements for the prediction of distinct biophysical and biochemical parameters in the laboratory and under field conditions, respectively. The estimation of parameters could be conducted to a great extent with high accuracy. An enhanced basis of calibration for the laboratory study and the first field experiment (grass/clover-mixture) yields in improved robustness of calibration models and allows for an extended application of spectroscopic measurement techniques, even under varying conditions. Furthermore, off-nadir measurements inside a canopy yield in higher prediction accuracies, particularly for crops characterised by distinct height increment as observed for maize.

Highly Sensitive Sensor Based On Intracavity Laser Absorption Spectroscopy By Means of Relative Intensity Noise

This thesis concerns with the main aspects of medical trace molecules detection by means of intracavity laser absorption spectroscopy (ICLAS), namely with the equirements for highly sensitive, highly selective, low price, and compact size sensor. A novel two modes semiconductor laser sensor is demonstrated. Its operation principle is based on the competition between these two modes. The sensor sensitivity is improved when the sample is placed inside the two modes laser cavity, and the competition between the two modes exists. The effects of the mode competition in ICLAS are discussed theoretically and experimentally. The sensor selectivity is enhanced using external cavity diode laser (ECDL) configuration, where the tuning range only depends on the external cavity configuration. In order to considerably reduce the sensor cost, relative intensity noise (RIN) is chosen for monitoring the intensity ratio of the two modes. RIN is found to be an excellent indicator for the two modes intensity ratio variations which strongly supports the sensor methodology. On the other hand, it has been found that, wavelength tuning has no effect on the RIN spectrum which is very beneficial for the proposed detection principle. In order to use the sensor for medical applications, the absorption line of an anesthetic sample, propofol, is measured. Propofol has been dissolved in various solvents. RIN has been chosen to monitor the sensor response. From the measured spectra, the sensor sensitivity enhancement factor is found to be of the order of 10^(3) times of the conventional laser spectroscopy.

Status and Potential of Smallholder Livestock Production Systems in Xishuangbanna, southern P.R. China

With Chinas rapid economic development during the last decades, the national demand for livestock products has quadrupled within the last 20 years. Most of that increase in demand has been answered by subsidized industrialized production systems, while million of smallholders, which still provide the larger share of livestock products in the country, have been neglected. Fostering those systems would help China to lower its strong urban migration streams, enhance the livelihood of poorer rural population and provide environmentally save livestock products which have a good chance to satisfy customers demand for ecological food. Despite their importance, China’s smallholder livestock keepers have not yet gained appropriate attention from governmental authorities and researchers. However, profound analysis of those systems is required so that adequate support can lead to a better resource utilization and productivity in the sector. To this aim, this pilot study analyzes smallholder livestock production systems in Xishuangbanna, located in southern China. The area is bordered by Lao and Myanmar and geographically counts as tropical region. Its climate is characterized by dry and temperate winters and hot summers with monsoon rains from May to October. While the regionis plain, at about 500 m asl above sea level in the south, outliers of the Himalaya mountains reach out into the north of Xishuangbanna, where the highest peak reaches 2400 m asl. Except of one larger city, Jinghong, Xishuangbanna mainly is covered by tropical rainforest, areas under agricultural cultivation and villages. The major income is generated through inner-Chinese tourism and agricultural production. Intensive rubber plantations are distinctive for the lowland plains while small-scaled traditional farms are scattered in the mountane regions. In order to determine the current state and possible future chances of smallholder livestock production in that region, this study analyzed the current status of the smallholder livestock sector in the Naban River National Nature Reserve (NRNNR), an area which is largely representative for the whole prefecture. It covers an area of about 50square kilometer and reaches from 470 up to 2400 m asl. About 5500 habitants of different ethnic origin are situated in 24 villages. All data have been collected between October 2007 and May 2010. Three major objectives have been addressed in the study: 1. Classifying existing pig production systems and exploring respective pathways for development 2. Quantifying the performance of pig breeding systemsto identify bottlenecks for production 3. Analyzing past and current buffalo utilization to determine the chances and opportunities of buffalo keeping in the future In order to classify the different pig production s ystems, a baseline survey (n=204, stratified cluster sampling) was carried out to gain data about livestock species, numbers, management practices, cultivated plant species and field sizes as well associo-economic characteristics. Sampling included two clusters at village level (altitude, ethnic affiliation), resulting in 13 clusters of which 13-17 farms were interviewed respectively. Categorical Principal Component Analysis (CatPCA) and a two-step clustering algorithm have been applied to identify determining farm characteristics and assort recorded households into classes of livestock production types. The variables keep_sow_yes/no, TLU_pig, TLU_buffalo, size_of_corn_fields, altitude_class, size_of_tea_plantationand size_of_rubber_fieldhave been found to be major determinants for the characterization of the recorded farms. All farms have extensive or semi-intensive livestock production, pigs and buffaloes are predominant livestock species while chicken and aquaculture are available but play subordinate roles for livelihoods. All pig raisers rely on a single local breed, which is known as Small Ear Pig (SMEP) in the region. Three major production systemshave been identified: Livestock-corn based LB; 41%), rubber based (RB; 39%) and pig based (PB;20%) systems. RB farms earn high income from rubber and fatten 1.9 ±1.80 pigs per household (HH), often using purchased pig feed at markets. PB farms own similar sized rubber plantations and raise 4.7 ±2.77 pigs per HH, with fodder mainly being cultivated and collected in theforest. LB farms grow corn, rice and tea and keep 4.6 ±3.32 pigs per HH, also fed with collected and cultivated fodder. Only 29% of all pigs were marketed (LB: 20%; RB: 42%; PB: 25%), average annual mortality was 4.0 ±4.52 pigs per farm (LB: 4.6 ±3.68; RB: 1.9 ±2.14; PB: 7.1 ±10.82). Pig feed mainly consists of banana pseudo stem, corn and rice hives and is prepared in batches about two to three times per week. Such fodder might be sufficient in energy content but lacks appropriate content of protein. Pigs therefore suffer from malnutrition, which becomes most critical in the time before harvest season around October. Farmers reported high occurrences of gastrointestinal parasites in carcasses and often pig stables were wet and filled with manure. Deficits in nutritional and hygienic management are major limits for development and should be the first issues addressed to improve productivity. SME pork was found to be known and referred by local customers in town and by richer lowland farmers. However, high prices and lacking availability of SME pork at local wet-markets were the reasons which limited purchase. If major management constraints are overcome, pig breeders (PB and LB farms) could increase the share of marketed pigs for town markets and provide fatteners to richer RB farmers. RB farmers are interested in fattening pigs for home consumption but do not show any motivation for commercial pig raising. To determine the productivity of input factors in pig production, eproductive performance, feed quality and quantity as well as weight development of pigs under current management were recorded. The data collection included a progeny history survey covering 184 sows and 437 farrows, bi-weekly weighing of 114 pigs during a 16-months time-span on 21 farms (10 LB and 11 PB) as well as the daily recording of feed quality and quantity given to a defined number of pigs on the same 21 farms. Feed samples of all recorded ingredients were analyzed for their respective nutrient content. Since no literature values on thedigestibility of banana pseudo stem – which is a major ingredient of traditional pig feed in NRNNR – were found, a cross-sectional digestibility trial with 2x4 pigs has been conducted on a station in the research area. With the aid of PRY Herd Life Model, all data have been utilized to determine thesystems’ current (Status Quo = SQ) output and the productivity of the input factor “feed” in terms of saleable life weight per kg DM feed intake and monetary value of output per kg DM feed intake.Two improvement scenarios were simulated, assuming 1) that farmers adopt a culling managementthat generates the highest output per unit input (Scenario 1; SC I) and 2) that through improved feeding, selected parameters of reproduction are improved by 30% (SC II). Daily weight gain averaged 55 ± 56 g per day between day 200 and 600. The average feed energy content of traditional feed mix was 14.92 MJ ME. Age at first farrowing averaged 14.5 ± 4.34 months, subsequent inter-farrowing interval was 11.4 ± 2.73 months. Littersize was 5.8 piglets and weaning age was 4.3 ± 0.99 months. 18% of piglets died before weaning. Simulating pig production at actualstatus, it has been show that monetary returns on inputs (ROI) is negative (1:0.67), but improved (1:1.2) when culling management was optimized so that highest output is gained per unit feed input. If in addition better feeding, controlled mating and better resale prices at fixed dates were simulated, ROI further increased to 1:2.45, 1:2.69, 1:2.7 and 1:3.15 for four respective grower groups. Those findings show the potential of pork production, if basic measures of improvement are applied. Futureexploration of the environment, including climate, market-season and culture is required before implementing the recommended measures to ensure a sustainable development of a more effective and resource conserving pork production in the future. The two studies have shown that the production of local SME pigs plays an important role in traditional farms in NRNNR but basic constraints are limiting their productivity. However, relatively easy approaches are sufficient for reaching a notable improvement. Also there is a demand for more SME pork on local markets and, if basic constraints have been overcome, pig farmers could turn into more commercial producers and provide pork to local markets. By that, environmentally safe meat can be offered to sensitive consumers while farmers increase their income and lower the risk of external shocks through a more diverse income generating strategy. Buffaloes have been found to be the second important livestock species on NRNNR farms. While they have been a core resource of mixed smallholderfarms in the past, the expansion of rubber tree plantations and agricultural mechanization are reasons for decreased swamp buffalo numbers today. The third study seeks to predict future utilization of buffaloes on different farm types in NRNNR by analyzing the dynamics of its buffalo population and land use changes over time and calculating labor which is required for keeping buffaloes in view of the traction power which can be utilized for field preparation. The use of buffaloes for field work and the recent development of the egional buffalo population were analyzed through interviews with 184 farmers in 2007/2008 and discussions with 62 buffalo keepers in 2009. While pig based farms (PB; n=37) have abandoned buffalo keeping, 11% of the rubber based farms (RB; n=71) and 100% of the livestock-corn based farms (LB; n=76) kept buffaloes in 2008. Herd size was 2.5 ±1.80 (n=84) buffaloes in early 2008 and 2.2 ±1.69 (n=62) in 2009. Field work on own land was the main reason forkeeping buffaloes (87.3%), but lending work buffaloes to neighbors (79.0%) was also important. Other purposes were transport of goods (16.1%), buffalo trade (11.3%) and meat consumption(6.4%). Buffalo care required 6.2 ±3.00 working hours daily, while annual working time of abuffalo was 294 ±216.6 hours. The area ploughed with buffaloes remained constant during the past 10 years despite an expansion of land cropped per farm. Further rapid replacement of buffaloes by tractors is expected in the near future. While the work economy is drastically improved by the use of tractors, buffaloes still can provide cheap work force and serve as buffer for economic shocks on poorer farms. Especially poor farms, which lack alternative assets that could quickly be liquidizedin times of urgent need for cash, should not abandon buffalo keeping. Livestock has been found to be a major part of small mixed farms in NRNNR. The general productivity was low in both analyzed species, buffaloes and pigs. Productivity of pigs can be improved through basic adjustments in feeding, reproductive and hygienic management, and with external support pig production could further be commercialized to provide pork and weaners to local markets and fattening farms. Buffalo production is relatively time intensive, and only will be of importance in the future to very poor farms and such farms that cultivate very small terraces on steep slopes. These should be encouraged to further keep buffaloes. With such measures, livestock production in NRNNR has good chances to stay competitive in the future.

Effects of plant diversity on bioenergy parameters in grassland biomass

Extensive grassland biomass for bioenergy production has long been subject of scientific research. The possibility of combining nature conservation goals with a profitable management while reducing competition with food production has created a strong interest in this topic. However, the botanical composition will play a key role for solid fuel quality of grassland biomass and will have effects on the combustion process by potentially causing corrosion, emission and slagging. On the other hand, botanical composition will affect anaerobic digestibility and thereby the biogas potential. In this thesis aboveground biomass from the Jena-Experiment plots was harvested in 2008 and 2009 and analysed for the most relevant chemical constituents effecting fuel quality and anaerobic digestibility. Regarding combustion, the following parameters were of main focus: higher heating value (HHV), gross energy yield (GE), ash content, ash softening temperature (AST), K, Ca, Mg, N, Cl and S content. For biogas production the following parameters were investigated: substrate specific methane yield (CH4 sub), area specific methane yield (CH4 area), crude fibre (CF), crude protein (CP), crude lipid (CL) and nitrogen-free extract (NfE). Furthermore, an improvement of the fuel quality was investigated through applying the Integrated generation of solid Fuel and Biogas from Biomass (IFBB) procedure. Through the specific setup of the Jena-Experiment it was possible to outline the changes of these parameters along two diversity gradients: (i) species richness (SR; 1 to 60 species) and (ii) functional group (grasses, legumes, small herbs and tall herbs) presence. This was a novel approach on investigating the bioenergy characteristic of extensive grassland biomass and gave detailed insight in the sward-composition¬ - bioenergy relations such as: (i) the most relevant SR effect was the increase of energy yield for both combustion (annual GE increased by 26% from SR8→16 and by 65% from SR8→60) and anaerobic digestion (annual CH4 area increased by 22% from SR8→16 and by 49% from SR8→60) through a strong interaction of SR with biomass yield; (ii) legumes play a key role for the utilization of grassland biomass for energy production as they increase the energy content of the substrate (HHV and CH4 sub) and the energy yield (GE and CH4 area); (iii) combustion is the conversion technique that will yield the highest energy output but requires an improvement of the solid fuel quality in order to reduce the risk of corrosion, emission and slagging related problems. This was achieved through applying the IFBB-procedure, with reductions in ash (by 23%), N (28%), K (85%), Cl (56%) and S (59%) and equal levels of concentrations along the SR gradient.

First-principles electronic theory of non-collinear magnetic order in transition-metal nanowires

The structural, electronic and magnetic properties of one-dimensional 3d transition-metal (TM) monoatomic chains having linear, zigzag and ladder geometries are investigated in the frame-work of first-principles density-functional theory. The stability of long-range magnetic order along the nanowires is determined by computing the corresponding frozen-magnon dispersion relations as a function of the 'spin-wave' vector q. First, we show that the ground-state magnetic orders of V, Mn and Fe linear chains at the equilibrium interatomic distances are non-collinear (NC) spin-density waves (SDWs) with characteristic equilibrium wave vectors q that depend on the composition and interatomic distance. The electronic and magnetic properties of these novel spin-spiral structures are discussed from a local perspective by analyzing the spin-polarized electronic densities of states, the local magnetic moments and the spin-density distributions for representative values q. Second, we investigate the stability of NC spin arrangements in Fe zigzag chains and ladders. We find that the non-collinear SDWs are remarkably stable in the biatomic chains (square ladder), whereas ferromagnetic order (q =0) dominates in zigzag chains (triangular ladders). The different magnetic structures are interpreted in terms of the corresponding effective exchange interactions J(ij) between the local magnetic moments μ(i) and μ(j) at atoms i and j. The effective couplings are derived by fitting a classical Heisenberg model to the ab initio magnon dispersion relations. In addition they are analyzed in the framework of general magnetic phase diagrams having arbitrary first, second, and third nearest-neighbor (NN) interactions J(ij). The effect of external electric fields (EFs) on the stability of NC magnetic order has been quantified for representative monoatomic free-standing and deposited chains. We find that an external EF, which is applied perpendicular to the chains, favors non-collinear order in V chains, whereas it stabilizes the ferromagnetic (FM) order in Fe chains. Moreover, our calculations reveal a change in the magnetic order of V chains deposited on the Cu(110) surface in the presence of external EFs. In this case the NC spiral order, which was unstable in the absence of EF, becomes the most favorable one when perpendicular fields of the order of 0.1 V/Å are applied. As a final application of the theory we study the magnetic interactions within monoatomic TM chains deposited on graphene sheets. One observes that even weak chain substrate hybridizations can modify the magnetic order. Mn and Fe chains show incommensurable NC spin configurations. Remarkably, V chains show a transition from a spiral magnetic order in the freestanding geometry to FM order when they are deposited on a graphene sheet. Some TM-terminated zigzag graphene-nanoribbons, for example V and Fe terminated nanoribbons, also show NC spin configurations. Finally, the magnetic anisotropy energies (MAEs) of TM chains on graphene are investigated. It is shown that Co and Fe chains exhibit significant MAEs and orbital magnetic moments with in-plane easy magnetization axis. The remarkable changes in the magnetic properties of chains on graphene are correlated to charge transfers from the TMs to NN carbon atoms. Goals and limitations of this study and the resulting perspectives of future investigations are discussed.

Adding QoS protection in order to enhance MPLS QoS routing

In this paper, a method for enhancing current QoS routing methods by means of QoS protection is presented. In an MPLS network, the segments (links) to be protected are predefined and an LSP request involves, apart from establishing a working path, creating a specific type of backup path (local, reverse or global). Different QoS parameters, such as network load balancing, resource optimization and minimization of LSP request rejection should be considered. QoS protection is defined as a function of QoS parameters, such as packet loss, restoration time, and resource optimization. A framework to add QoS protection to many of the current QoS routing algorithms is introduced. A backup decision module to select the most suitable protection method is formulated and different case studies are analyzed

Definición de una estrategia de servicio para los adultos mayores en la modalidad de club: Club para Adultos Mayores de Bogotá "Porque tienes más de 60 razones para empezar a disfrutar"

El desarrollo de este trabajo busca la definición y presentación de la mejor estrategia de servicio en la modalidad de club exclusivo y de esparcimiento para a adultos mayores de la ciudad de Bogotá y potencialmente la de todo el país. Con el propósito de definir la mejor estrategia para logar un proyecto exitoso, y de esta manera cumplir con el objetivo propuesto, el trabajo fue estructurado de la siguiente manera: primero definió, conceptualizo y caracterizo la población objetivo; segundo, formuló una estrategia de servicio para esta población en orden de brindar una solución al problema de: “escasez de instituciones integrales y diferentes a casas u hogares geriátricos y que cumplan con los parámetros legales e instituidos para el cuidado y la distracción de los adultos mayores” guiada por la teoría de la estrategia competitiva, enfoque y posición estratégica de Michael Porter, tercero intentó validar dicha estrategia a través de la aplicación de dos herramientas: panorama competitivo y análisis de fuerzas del mercado pertenecientes a la teoría de análisis estructurales de sectores estratégicos, cuarto presentó y evaluó como posible barrera de entrada un marco legal para el proyecto, y por ultimo realizo una proyección financiera para el mismo, mostrando su viabilidad y reafirmando que la estrategia presentada realmente puede hacer de este proyecto una empresa perdurable y rentable.