Analysis of simple hardware efficiency for temperature measurement in agriculture and environment

This work focuses basically on the design and analysis of simple and low cost hardware systems efficiency for temperature measurement in agricultural area. The main objective is to prove quantitatively, through statistical data analysis, to what extent a simple hardware designed with inexpensive components can be used safely in the indoor temperature measurement in farm buildings, such as greenhouses, warehouse or silos. To verify the of simple hardware efficiency, its data were compared with data from measurements with a high performance LabVIEW platform. This work proved that a simple hardware based on a microcontroller and the LM35 sensor can perform well. It presented a good accuracy but a relatively low precision that can be improved when performed some consecutive signal sampling and then used its average value. Although there are many papers that explain these components, this work has the distinction of presenting a data analysis in numerical form and using high performance systems to ensure critical data comparison.

Discovery and cross-section measurement of neutron-rich isotopes in the element range from neodymium to platinum with the FRS

Using the high-resolution performance of the fragment separator FRS at GSI we have discovered 60 new neutron-rich isotopes in the atomic number range of 60 <= Z <= 78. The new isotopes were unambiguously identified in reactions with a U-238 beam impinging on a Be target at 1 GeV/nucleon. The production cross-section for the new isotopes have been measured down to the pico-barn level and compared with predictions of different model calculations. For elements above hafnium fragmentation is the dominant reaction mechanism which creates the new isotopes, whereas fission plays a dominant role for the production of the new isotopes up to thulium. (C) 2012 Elsevier B.V. All rights reserved.

Analysis of the interplay between knowledge and performance management in industrial clusters

The concept of industrial clustering has been studied in-depth by policy makers and researchers from many fields, mainly due to the competitive advantages it may bring to regional economies. Companies often take part in collaborative initiatives with local partners while also taking advantage of knowledge spillovers to benefit from locating in a cluster. Thus, Knowledge Management (KM) and Performance Management (PM) have become relevant topics for policy makers and cluster associations when undertaking collaborative initiatives. Taking this into account, this paper aims to explore the interplay between both topics using a case study conducted in a collaborative network formed within a cluster. The results show that KM should be acknowledged as a formal area of cluster management so that PM practices can support knowledge-oriented initiatives and therefore make better use of the new knowledge created. Furthermore, tacit and explicit knowledge resulting from PM practices needs to be stored and disseminated throughout the cluster as a way of improving managerial practices and regional strategic direction. Knowledge Management Research & Practice (2012) 10, 368-379. doi:10.1057/kmrp.2012.23

Evolution of form and function: morphophysiological relationships and locomotor performance in tropidurine lizards

Locomotor capacity is often considered an excellent measure of whole animal performance because it requires the integrated functioning of many morphological, physiological (and biochemical) traits. However, because studies tend to focus on either structural or functional suits of traits, we know little on whether and how morphological and physiological traits coevolve to produce adequate locomotor capacities. Hence, we investigate the evolutionary relationships between morphological and physiological parameters related to exercise physiology, using tropidurine lizards as a model. We employ a phylogenetic principal component analysis (PCA) to identify variable clusters (factors) related to morphology, energetic metabolism and muscle metabolism, and then analyze the relationships between these clusters and measures of locomotor performance, using two models (star and hierarchical phylogenies). Our data indicate that sprint performance is enhanced by simultaneous evolutionary tendencies affecting relative limb and tail size and physiological traits. Specifically, the high absolute sprint speeds exhibited by tropidurines from the sand dunes are explained by longer limbs, feet and tails and an increased proportion of glycolytic fibers in the leg muscle, contrasting with their lower capacity for overall oxidative metabolism [principal component (PC1)]. However, when sprint speeds are corrected for body size, performance correlates with a cluster (PC3) composed by moderate loads for activity metabolic rate and body size. The simultaneous measurement of morphological and physiological parameters is a powerful tool for exploring patterns of coadaptation and proposing morphophysiological associations that are not directly predictable from theory. This approach may trigger novel directions for investigating the evolution of form and function, particularly in the context of organismal performance.

Preparation of percentile tables through anthropometric, performance, biochemical, hematological, hormonal and psychological parameters in professional soccer players

Introduction: The lack of reference values of anthropometric, performance, biochemical, hematological, hormonal and psychological parameters is an important limitation in the investigations with soccer players. Objective: To elaborate percentile tables to be used as comparison reference for further studies. Methods: 82 professional soccer players were evaluated approximately 30 days after the beginning of the main competition played by their teams. On the first day of evaluation, fast blood samples were collected for measurement of hematological parameters (i.e. erythrocytes, hemoglobin, hematocrit, mean corpuscular volume - MCV, mean corpuscular hemoglobin - MCH, mean corpuscular hemoglobin concentration - MCHC, leukocytes, eosinophils, lymphocytes, monocytes and platelets) and of concentrations of adrenaline, cortisol, creatine kinase, creatinine, norepinephrine, testosterone and urea. Subsequently, the soccer players had their anthropometric characteristics and psychological parameters assessed. In addition, the evaluation of the lactic anaerobic system efficiency was performed on a 400-m track. On the second day, both the alactic anaerobic and aerobic system efficiency was measured. Results: The percentile distribution (P-0, P-15, P-30, P-50, P-70, P-85 e P-100) was used to present the results. Conclusion: The elaboration of the percentile tables can be used as comparison reference for further studies.

Evaluation of reference-based two-color methods for measurement of gene expression ratios using spotted cDNA microarrays

Abstract Background Spotted cDNA microarrays generally employ co-hybridization of fluorescently-labeled RNA targets to produce gene expression ratios for subsequent analysis. Direct comparison of two RNA samples in the same microarray provides the highest level of accuracy; however, due to the number of combinatorial pair-wise comparisons, the direct method is impractical for studies including large number of individual samples (e.g., tumor classification studies). For such studies, indirect comparisons using a common reference standard have been the preferred method. Here we evaluated the precision and accuracy of reconstructed ratios from three indirect methods relative to ratios obtained from direct hybridizations, herein considered as the gold-standard. Results We performed hybridizations using a fixed amount of Cy3-labeled reference oligonucleotide (RefOligo) against distinct Cy5-labeled targets from prostate, breast and kidney tumor samples. Reconstructed ratios between all tissue pairs were derived from ratios between each tissue sample and RefOligo. Reconstructed ratios were compared to (i) ratios obtained in parallel from direct pair-wise hybridizations of tissue samples, and to (ii) reconstructed ratios derived from hybridization of each tissue against a reference RNA pool (RefPool). To evaluate the effect of the external references, reconstructed ratios were also calculated directly from intensity values of single-channel (One-Color) measurements derived from tissue sample data collected in the RefOligo experiments. We show that the average coefficient of variation of ratios between intra- and inter-slide replicates derived from RefOligo, RefPool and One-Color were similar and 2 to 4-fold higher than ratios obtained in direct hybridizations. Correlation coefficients calculated for all three tissue comparisons were also similar. In addition, the performance of all indirect methods in terms of their robustness to identify genes deemed as differentially expressed based on direct hybridizations, as well as false-positive and false-negative rates, were found to be comparable. Conclusion RefOligo produces ratios as precise and accurate as ratios reconstructed from a RNA pool, thus representing a reliable alternative in reference-based hybridization experiments. In addition, One-Color measurements alone can reconstruct expression ratios without loss in precision or accuracy. We conclude that both methods are adequate options in large-scale projects where the amount of a common reference RNA pool is usually restrictive.

Personal and Social Performance (PSP) scale for patients with schizophrenia: translation to Portuguese, cross-cultural adaptation and interrater reliability

INTRODUCTION: Schizophrenia is a chronic mental disorder associated with impairment in social functioning. The most widely used scale to measure social functioning is the GAF (Global Assessment of Functioning), but it has the disadvantage of measuring at the same time symptoms and functioning, as described in its anchors. OBJECTIVES:Translation and cultural adaptation of the PSP, proposing a final version in Portuguese for use in Brazil. METHODS: We performed five steps: 1) translation; 2) back translation; 3) formal assessment of semantic equivalence; 4) debriefing; 5) analysis by experts. Interrater reliability (Intraclass correlation, ICC) between two raters was also measured. RESULTS: The final version was applied by two independent investigators in 18 adults with schizophrenia (DSM-IV-TR). The interrater reliability (ICC) was 0.812 (p < 0.001). CONCLUSION: The translation and adaptation of the PSP had an adequate level of semantic equivalence between the Portuguese version and the original English version. There were no difficulties related to understanding the content expressed in the translated texts and terms. Its application was easy and it showed a good interrater reliability. The PSP is a valid instrument for the measurement of personal and social functioning in schizophrenia.

Intangible resources and organization capital: measurement and economic evaluation

Intangible resources have raised the interests of scholars from different research areas due to their importance as crucial factors for firm performance; yet, contributions to this field still lack a theoretical framework. This research analyses the state-of-the-art results reached in the literature concerning intangibles, their main features and evaluation problems and models. In search for a possible theoretical framework, the research draws a kind of indirect analysis of intangibles through the theories of the firm, their critic and developments. The heterodox approaches of the evolutionary theory and resource-based view are indicated as possible frameworks. Based on this theoretical analysis, organization capital (OC) is identified, for its features, as the most important intangible for firm performance. Empirical studies on the relationship intangibles-firm performance have been sporadic and have failed to reach firm conclusions with respect to OC; in the attempt to fill this gap, the effect of OC is tested on a large sample of European firms using the Compustat Global database. OC is proxied by capitalizing an income statement item (Selling, General and Administrative expenses) that includes expenses linked to information technology, business process design, reputation enhancement and employee training. This measure of OC is employed in a cross-sectional estimation of a firm level production function - modeled with different functional specifications (Cobb-Douglas and Translog) - that measures OC contribution to firm output and profitability. Results are robust and confirm the importance of OC for firm performance.

Development and characterization of a distributed measurement system for the evaluation of voltage quality in electric power networks

The research activity carried out during the PhD course in Electrical Engineering belongs to the branch of electric and electronic measurements. The main subject of the present thesis is a distributed measurement system to be installed in Medium Voltage power networks, as well as the method developed to analyze data acquired by the measurement system itself and to monitor power quality. In chapter 2 the increasing interest towards power quality in electrical systems is illustrated, by reporting the international research activity inherent to the problem and the relevant standards and guidelines emitted. The aspect of the quality of voltage provided by utilities and influenced by customers in the various points of a network came out only in recent years, in particular as a consequence of the energy market liberalization. Usually, the concept of quality of the delivered energy has been associated mostly to its continuity. Hence the reliability was the main characteristic to be ensured for power systems. Nowadays, the number and duration of interruptions are the “quality indicators” commonly perceived by most customers; for this reason, a short section is dedicated also to network reliability and its regulation. In this contest it should be noted that although the measurement system developed during the research activity belongs to the field of power quality evaluation systems, the information registered in real time by its remote stations can be used to improve the system reliability too. Given the vast scenario of power quality degrading phenomena that usually can occur in distribution networks, the study has been focused on electromagnetic transients affecting line voltages. The outcome of such a study has been the design and realization of a distributed measurement system which continuously monitor the phase signals in different points of a network, detect the occurrence of transients superposed to the fundamental steady state component and register the time of occurrence of such events. The data set is finally used to locate the source of the transient disturbance propagating along the network lines. Most of the oscillatory transients affecting line voltages are due to faults occurring in any point of the distribution system and have to be seen before protection equipment intervention. An important conclusion is that the method can improve the monitored network reliability, since the knowledge of the location of a fault allows the energy manager to reduce as much as possible both the area of the network to be disconnected for protection purposes and the time spent by technical staff to recover the abnormal condition and/or the damage. The part of the thesis presenting the results of such a study and activity is structured as follows: chapter 3 deals with the propagation of electromagnetic transients in power systems by defining characteristics and causes of the phenomena and briefly reporting the theory and approaches used to study transients propagation. Then the state of the art concerning methods to detect and locate faults in distribution networks is presented. Finally the attention is paid on the particular technique adopted for the same purpose during the thesis, and the methods developed on the basis of such approach. Chapter 4 reports the configuration of the distribution networks on which the fault location method has been applied by means of simulations as well as the results obtained case by case. In this way the performance featured by the location procedure firstly in ideal then in realistic operating conditions are tested. In chapter 5 the measurement system designed to implement the transients detection and fault location method is presented. The hardware belonging to the measurement chain of every acquisition channel in remote stations is described. Then, the global measurement system is characterized by considering the non ideal aspects of each device that can concur to the final combined uncertainty on the estimated position of the fault in the network under test. Finally, such parameter is computed according to the Guide to the Expression of Uncertainty in Measurements, by means of a numeric procedure. In the last chapter a device is described that has been designed and realized during the PhD activity aiming at substituting the commercial capacitive voltage divider belonging to the conditioning block of the measurement chain. Such a study has been carried out aiming at providing an alternative to the used transducer that could feature equivalent performance and lower cost. In this way, the economical impact of the investment associated to the whole measurement system would be significantly reduced, making the method application much more feasible.

Performance Analysis and Improvements for the Future Aeronautical Mobile Airport Communications System (AeroMACS)

This thesis deals with the development of the upcoming aeronautical mobile airport communications system (AeroMACS) system. We analyzed the performance of AeroMACS and we investigated potential solutions for enhancing its performance. Since the most critical results correspond to the channel scenario having less diversity1, we tackled this problem investigating potential solutions for increasing the diversity of the system and therefore improving its performance. We accounted different forms of diversity as space diversity and time diversity. More specifically, space (antenna and cooperative) diversity and time diversity are analyzed as countermeasures for the harsh fading conditions that are typical of airport environments. Among the analyzed techniques, two novel concepts are introduced, namely unequal diversity coding and flexible packet level codes. The proposed techniques have been analyzed on a novel airport channel model, derived from a measurement campaign at the airport of Munich (Germany). The introduced techniques largely improve the performance of the conventional AeroMACS link; representing thus appealing solutions for the long term evolution of the system.

Innovation and economic performance of the firms in the service sector: relevant issues and open problems

This thesis is a collection of essays related to the topic of innovation in the service sector. The choice of this structure is functional to the purpose of single out some of the relevant issues and try to tackle them, revising first the state of the literature and then proposing a way forward. Three relevant issues has been therefore selected: (i) the definition of innovation in the service sector and the connected question of measurement of innovation; (ii) the issue of productivity in services; (iii) the classification of innovative firms in the service sector. Facing the first issue, chapter II shows how the initial width of the original Schumpeterian definition of innovation has been narrowed and then passed to the service sector form the manufacturing one in a reduce technological form. Chapter III tackle the issue of productivity in services, discussing the difficulties for measuring productivity in a context where the output is often immaterial. We reconstruct the dispute on the Baumol’s cost disease argument and propose two different ways to go forward in the research on productivity in services: redefining the output along the line of a characteristic approach; and redefining the inputs, particularly analysing which kind of input it’s worth saving. Chapter IV derives an integrated taxonomy of innovative service and manufacturing firms, using data coming from the 2008 CIS survey for Italy. This taxonomy is based on the enlarged definition of “innovative firm” deriving from the Schumpeterian definition of innovation and classify firms using a cluster analysis techniques. The result is the emergence of a four cluster solution, where firms are differentiated by the breadth of the innovation activities in which they are involved. Chapter 5 reports some of the main conclusions of each singular previous chapter and the points worth of further research in the future.

Measurement of K(892)*0 resonance production in Pb-Pb collisions with the ALICE experiment at the LHC

The analysis of the K(892)*0 resonance production in Pb–Pb collisions at √sNN = 2.76 TeV with the ALICE detector at the LHC is presented. The analysis is motivated by the interest in the measurement of short-lived resonances production that can provide insights on the properties of the medium produced in heavy-ion collisions both during its partonic (Quark-Gluon Plasma) and hadronic phase. This particular analysis exploits particle identification of the ALICE Time-Of-Flight detector. The ALICE experiment is presented, with focus on the performance of the Time-Of-Flight system. The aspects of calibration and data quality controls are discussed in detail, while illustrating the excellent and very stable performance of the system in different collision environments at the LHC. A full analysis of the K*0 resonance production is presented: from the resonance reconstruction to the determination of the efficiency and the systematic uncertainty. The results show that the analysis strategy discussed is a valid tool to measure the K∗0 up to intermediate momenta. Preliminary results on K*0 resonance production at the LHC are presented and confirmed to be a powerful tool to study the physics of ultra-relativistic heavy-ion collisions.

Tracking, b-tagging and measurement of the b-jet production cross section with the ATLAS detector

The Standard Model of elementary particle physics was developed to describe the fundamental particles which constitute matter and the interactions between them. The Large Hadron Collider (LHC) at CERN in Geneva was built to solve some of the remaining open questions in the Standard Model and to explore physics beyond it, by colliding two proton beams at world-record centre-of-mass energies. The ATLAS experiment is designed to reconstruct particles and their decay products originating from these collisions. The precise reconstruction of particle trajectories plays an important role in the identification of particle jets which originate from bottom quarks (b-tagging). This thesis describes the step-wise commissioning of the ATLAS track reconstruction and b-tagging software and one of the first measurements of the b-jet production cross section in pp collisions at sqrt(s)=7 TeV with the ATLAS detector. The performance of the track reconstruction software was studied in great detail, first using data from cosmic ray showers and then collisions at sqrt(s)=900 GeV and 7 TeV. The good understanding of the track reconstruction software allowed a very early deployment of the b-tagging algorithms. First studies of these algorithms and the measurement of the b-tagging efficiency in the data are presented. They agree well with predictions from Monte Carlo simulations. The b-jet production cross section was measured with the 2010 dataset recorded by the ATLAS detector, employing muons in jets to estimate the fraction of b-jets. The measurement is in good agreement with the Standard Model predictions.

Sea level measurement using single GNSS antenna SNR signals

This thesis presents a possible method to calculate sea level variation using geodetic-quality Global Navigate Satellite System (GNSS) receivers. Three antennas are used: two small antennas and a choke ring one, analyzing only Global Positioning System signals. The main goal of the thesis is to test a modified configuration for antenna set up. In particular, measurements obtained tilting one antenna to face the horizon are compared to measurements obtained from antennas looking upward. The location of the experiment is a coastal environment nearby the Onsala Space Observatory in Sweden. Sea level variations are obtained using periodogram analysis of the SNR signal and compared to synthetic gauge generated from two independent tide gauges. The choke ring antenna provides poor result, with an RMS around 6 cm and a correlation coefficients of 0.89. The smaller antennas provide correlation coefficients around 0.93. The antenna pointing upward present an RMS of 4.3 cm and the one pointing the horizon an RMS of 6.7 cm. Notable variation in the statistical parameters is found when modifying the length of the interval analyzed. In particular, doubts are risen on the reliability of certain scattered data. No relation is found between the accuracy of the method and weather conditions. Possible methods to enhance the available data are investigated, and correlation coefficient above 0.97 can be obtained with small antennas when sacrificing data points. Hence, the results provide evidence of the suitability of SNR signal analysis for sea level variation in coastal environment even in the case of adverse weather conditions. In particular, tilted configurations provides comparable result with upward looking geodetic antennas. A SNR signal simulator is also tested to investigate its performance and usability. Various configuration are analyzed in combination with the periodogram procedure used to calculate the height of reflectors. Consistency between the data calculated and those received is found, and the overall accuracy of the height calculation program is found to be around 5 mm for input height below 5 m. The procedure is thus found to be suitable to analyze the data provided by the GNSS antennas at Onsala.

Dal Bes ad Urbes: I piani di performance e di trasparenza nelle citta'

Obiettivo del lavoro è quello di legare tra di loro due aspetti che storicamente sono sempre stati scollegati. Il primo è il lungo dibattito sul tema “oltre il PIL”, che prosegue ininterrottamente da circa mezzo secolo. Il secondo riguarda l’utilizzo dei sistemi di misurazione e valutazione della performance nel settore pubblico italiano. Si illustra l’evoluzione del dibattito sul PIL facendo un excursus storico del pensiero critico che si è sviluppato nel corso di circa cinquanta anni analizzando le ragioni assunte dagli studiosi per confutare l’utilizzo del PIL quale misura universale del benessere. Cogliendo questa suggestione l’Istat, in collaborazione con il CNEL, ha avviato un progetto per individuare nuovi indicatori da affiancare al PIL, in grado di misurare il livello non solo della crescita economica, ma anche del benessere sociale e sostenibile, con l’analisi degli indicatori riferiti a 12 domini di benessere individuati. Al progetto Istat-CNEL si è affiancato il progetto UrBES, promosso dall’Istat e dal Coordinamento dei sindaci metropolitani dell’ANCI, che hanno costituito una rete di città metropolitane per sperimentare la misurazione e il confronto sulla base di indicatori di benessere urbano equo e sostenibile, facendo proprio un progetto del Comune di Bologna e di Laboratorio Urbano (Centro di documentazione, ricerca e proposta sulle città), che ha sottoposto a differenti target un questionario on line, i cui risultati, con riferimento alle risposte fornite alle domande aperte, sono stati elaborati attraverso l’utilizzo di Taltac, un software per l’analisi dei testi, al fine di individuare i “profili” dei rispondenti, associando i risultati dell’elaborazione alle variabili strutturali del questionario. Nell’ultima parte i servizi e progetti erogati dal comune di Bologna sono stati associati alle dimensioni UrBES, per valutare l’impatto delle politiche pubbliche sulla qualità della vita e sul benessere dei cittadini, indicando le criticità legate alla mancanza di dati adeguati.