Colonização e lesão em fêmeas ingurgitadas do carrapato Rhipicephalus sanguineus causadas pelo fungo Metarhizium anisopliae

O presente trabalho teve como objetivo verificar a forma de penetração do fungo Metarhizium anisopliae [METSCH. (SOROKIN, 1883)] em carrapatos da espécie Rhipicephalus sanguineus (LATREILLE, 1806), assim como as lesões infringidas nos tecidos internos do ácaro. A forma de aderência e penetração do fungo foi estudada através da microscopia eletrônica de varredura e a ação do fungo nos tecidos internos avaliada em secções histológicas convencionais. Para observação destes eventos, realizaram-se infecções experimentais em 11 grupos de fêmeas ingurgitadas do carrapato R. sanguineus contendo 12 fêmeas ingurgitadas cada. Para tal, as fêmeas ingurgitadas foram banhadas durante 3 minutos, sob agitação manual, em suspensão com concentração 108 conídios/mL. No caso dos grupos controle o banho foi realizado apenas no veículo da suspensão. Os carrapatos foram processados para histopatologia e microscopia eletrônica em diversos tempos após a infecção, a saber: 1 e 18h, e um, dois, três, quatro, cinco, seis, sete, nove e onze dias. Observou-se que a maior parte dos conídios germinou em até 18h após a inoculação e que o fungo penetrou no ácaro através do tegumento 48h após a infecção. Após a penetração, o fungo invadiu o corpo do hospedeiro promovendo uma colonização difusa, sem preferência aparente por tecidos específicos. Dentre as lesões nos tecidos internos do ácaro, ressalta-se o rompimento da parede intestinal e vazamento do conteúdo para a hemocele. A morte do hospedeiro ocorreu entre 96 e 120h pós-infecção, e a esporulação do patógeno sobre o cadáver do ácaro iniciou-se em torno de 120 a 144h pós-infecção. Espera-se, com este trabalho, contribuir para o desenvolvimento e viabilização de técnicas de controle biológico dos carrapatos por fungos como alternativa ao uso de acaricidas.

Eventos externos e internos da infecção de larvas e ninfas de Rhipicephalus sanguineus por Metarhizium anisopliae

Examinaram-se a adesão, a germinação, a penetração e a colonização de larvas e ninfas de Rhipicephalus sanguineus por Metarhizium anisopliae, assim como as lesões infringidas pelo fungo nas respectivas fases do ciclo de vida do ácaro. Realizaram-se infecções experimentais em 11 grupos contendo 250 larvas e 11 grupos contendo 75 ninfas de R. sanguineus, por meio de banho, durante três minutos sob agitação manual, em suspensão contendo 10(8) conídios/ml do fungo. Nos grupos-controles, o banho foi realizado usando o veículo da suspensão. Larvas e ninfas foram processadas para um estudo histopatológico e de microscopia eletrônica de varredura nos seguintes tempos após a infecção: uma e 18 horas, e um, dois, três, quatro, cinco, seis, sete, nove e 11 dias. A germinação dos conídios ocorreu em até 18 horas pós-inoculação, e o fungo penetrou nas larvas e ninfas através do tegumento, dois e três dias após a infecção, respectivamente. Após penetração, o fungo invadiu o corpo das larvas e ninfas, promovendo uma colonização difusa, sem preferência aparente por tecidos específicos. Lesões significativas não foram observadas. A morte das larvas e ninfas ocorreu no terceiro e quarto dias pós-infecção, e a esporulação do patógeno sobre o cadáver foi iniciada no sexto dia pós-infecção.

Influência do envelhecimento acelerado na anatomia da testa de sementes de soja, cv. Monsoy 8400

Durante o processo de envelhecimento, as sementes sofrem alterações degenerativas que influenciam o seu potencial fisiológico. Entre estas alterações podem estar as modificações anatômicas nas camadas celulares da testa da semente. Objetivou-se, com este trabalho, verificar a relação entre a anatomia da testa de sementes de soja, cultivar Monsoy 8400 e a germinação, após o envelhecimento acelerado, pelo fato da testa apresentar um papel fundamental na conservação do potencial fisiológico das sementes. As sementes foram envelhecidas a 42ºC e 100% UR do ar por períodos de zero, 24, 48, 72 e 96 horas. Avaliaram-se os teores de água e a germinação, posteriormente à secagem, seções transversais da testa de 10 sementes de cada tratamento foram eletromicrografadas, com microscópio eletrônico de varredura,,observando-se as camadas das células paliçádicas, ampulhetas e parenquimáticas A germinação declinou com o aumento dos períodos de envelhecimento. Houve redução da espessura das camadas da testa nos períodos de 48, 72 e 96 horas deste processo. Observou-se que, principalmente, para os períodos de envelhecimento de 72 e 96 horas, que as células da camada hipodérmica apresentaram um aspecto de colapso, sendo este acentuado para o período de 96 horas. A redução da espessura das camadas sugere a ocorrência de um colapso das células que compõem tais camadas, sendo um fator causador da redução do potencial germinativo.

Seed anatomy and germination of Phoenix roebelenii O'Brien (Arecaceae)

O objetivo desse trabalho foi estudar a morfologia, anatomia e o processo germinativo de sementes de Phoenix roebelenii. Para o levantamento dos dados biométricos foram utilizadas 100 sementes de frutos recém-colhidos, deixados secar ao ar por um dia. Para a germinação, quatro repetições de 50 sementes tratadas com Vitavax-Thiran foram semeadas em bandejas de plástico, contendo Sphagnum sp. como substrato e mantidas sob condições ambientais de laboratório. Detalhes da morfologia da semente foram documentados com o uso de microscopia eletrônica de varredura e esquematizados com auxílio de câmara clara, acoplada ao estereomicroscópio. Foram confeccionadas lâminas permanentes com cortes do embrião, para o estudo de sua anatomia. As dimensões médias das sementes foram: 10,32mm comprimento, 5,21mm largura e 3,91mm espessura. O peso de 1000 sementes foi de 151,1g e 1kg continha 6600 unidades. O início da germinação variou entre 27 e 58 dias. As sementes são albuminosas, com endosperma duro e o embrião é pouco diferenciado, lateral e periférico. A germinação inicia-se pela abertura de um opérculo, através do qual é emitido o pecíolo cotiledonar com o eixo embrionário na extremidade. O pecíolo funciona, internamente, como um haustório, digerindo gradativamente o endosperma. Na sua parte posterior, desenvolve-se a plúmula, que emerge através de uma fenda. Nota-se o aparecimento de raízes secundárias na porção anterior da raiz primária.

Análise de Argamassas Com Substituição Parcial do Cimento Portland Por Cinza Residual de Lenha de Algaroba

With the increase in cement consumption, it has quickly become one of the inputs most consumed by mankind over the last century. This has caused an increase in CO2 emissions, as cement production releases large quantities of this gas into the atmosphere. Adding this fact to the growing consciousness of environmental preservation, it has led to a search for alternatives to cement to complement its derivatives, in the form of waste materials like the ashes. This research aimed to analyze the properties of mortars in fresh and hardened state with partial replacement of Portland cement by residual algaroba wood ash (CRLA) potteries produced by the state of Rio Grande do Norte. The CRLA was collected and sieved, where part of it was ground and characterized in comparison with that just sifted, being characterized according to its chemical composition, grain size, fineness, density, bulk density and index of pozzolanic activity. It was found that the wood ash does not act as pozzolan, and grinding it has not changed its characteristics compared to those just sifted, not justifying its use. Two traces were adopted for this research: 1:3 (cement: fine sand) and 1:2:8 (cement: hydrated lime: medium sand); both in volume, using as materials the CRLA just sifted, CP II F-32 Portland cement, CH-I hydrated lime, river sand and water from the local utility. For each trace were adopted six percentages of partial replacement of cement for wood ash: 0% (control) 5%, 7%, 10%, 12% and 15%. In the fresh state, the mortars were tested towards their consistency index and mass density. In the hardened state, they were tested towards their tensile strength in bending, compressive strength and tensile adhesion strength, and its mass density in the hardened state. The mortar was also analyzed by scanning electron microscopy and X-ray diffraction. Furthermore, it was classified according to NBR 13281 (2005). The results showed that up to a content of 5% substitution and for both traces, the residual algaroba wood ash can replace Portland cement without compromising the mortars microstructure and its fresh and hardened state

Análise do Comportamento Mecânico de Concretos Produzidos com Incorporação de Cinza do Bagaço da Cana-de-Açúcar de Variedades SP911049, RB92579 E SP816949

Concrete is the second most consumed product in the world and the incorporation of the Sugar Bagasse Ash (SBA) into this material can provide solutions for the utilization of by-products from other industries, thus reducing the environmental impact. The general aim of this dissertation focuses on analyzing the mechanical behavior of concrete with addition of SBA from three different species of sugar cane, through tests of consistency, compressive strength, porosity, absorption, voids and Scanning Electron Microscopy (SEM). Were prepared 13 specimens for each specific pattern and level of incorporation of SBA (10%, 20% and 30%) of the three varieties collected, totaling 130 samples of concrete. The trait was employed 1:2:3 (cement: sand: aggregates) in relation to the cement mass with a water / cement ratio of 0.532 and 1% additive Tec 400 Mult also based on the weight of cement. According to the results obtained in this study, it was concluded that the variety of cane sugar, used in the production of the CBC, influenced the mechanical behavior of the resulting concrete. All concrete with addition of SBA, reported a reduction of at least 10% in the properties related to permeability and an increase in the compressive strength of at least 16% compared to standard concrete at 28 days

Degradabilidade in situ e observações microscópicas de volumosos em bovinos suplementados com enzimas fibrolíticas exógenas

Avaliou-se o efeito de enzimas fibrolíticas (celulase e xilanase) sobre a degradabilidade in situ da MS, PB, FDN, FDA e hemicelulose do feno de Tifton-85 (Cynodon spp.) cortado aos 30 e 90 dias e do bagaço de cana, utilizando-se seis bovinos com cânula no rúmen. As enzimas foram extraídas dos fungos Aspergillus niger e Trichoderma longibrachiatum e fornecidas, na quantidade de 0,75 g/kgMS.dia, por meio da cânula ruminal. Os tempos de incubação ruminal foram de 0, 3, 6, 12, 24, 48, 72 e 96 horas. Os resíduos de incubação foram avaliados por meio de microscopia eletrônica de varredura (MEV). O efeito da adição de enzimas sobre a degradação da MS e PB variou em função do volumoso estudado. A degradabilidade efetiva da MS do feno Tifton cortado aos 30 e 90 dias e do bagaço de cana sem a adição de enzimas foi de 61,85; 42,35 e 28,22%, respectivamente, e de 63,51; 40,64 e 31,43%, respectivamente, com a adição das enzimas. Não houve efeito das enzimas sobre a degradação da fibra. As observações ao MEV indicaram aumento da colonização bacteriana sobre a parede celular com a suplementação enzimática. A adição de enzimas fibrolíticas na dieta de ruminantes apresentou efeito pouco expressivo sobre os parâmetros de degradação ruminal dos volumosos estudados.

Análise de antenas utilizando substrato cerâmico, zpt, produzido por síntese auto propagante para aplicações em sistemas de micro-ondas

Ceramic substrates have been investigated by researchers around the world and has achieved a high interest in the scientific community, because they had high dielectric constants and excellent performance in the structures employed. Such ceramics result in miniaturized structures with dimensions well reduced and high radiation efficiency. In this work, we have used a new ceramic material called lead zinc titanate in the form of Zn0,8Pb0,2TiO3, capable of being used as a dielectric substrate in the construction of various structures of antennas. The method used in constructing the ceramic combustion synthesis was Self- Sustained High Temperature (SHS - "Self-Propagating High-Temperature Synthesis") which is defined as a process that uses highly exothermic reactions to produce various materials. Once initiated the reaction area in the reaction mixture, the heat generated is sufficient to become self-sustaining combustion in the form of a wave that propagates converting the reaction mixture into the product of interest. Were analyzed aspects of the formation of the composite Zn0,8Pb0,2TiO3 by SHS powders and characterized. The analysis consisted of determining the parameters of the reaction for the formation of the composite, as the ignition temperature and reaction mechanisms. The production of composite Zn0,8Pb0,2TiO3 by SHS performed in the laboratory, was the result of a total control of combustion temperature and after obtaining the powder began the development of ceramics. The product was obtained in the form of regular, alternating layers of porous ceramics and was obtained by uniaxial pressing. 10 The product was characterized by analysis of dilatometry, X-ray diffraction analysis and scanning electron microscopy. One of the contributions typically defined in this work is the development of a new dielectric material, nevertheless presented previously in the literature. Therefore, the structures of the antennas presented in this work consisted of new dielectric ceramics based Zn0,8Pb0,2TiO3 usually used as dielectric substrate. The materials produced were characterized in the microwave range. These are dielectrics with high relative permittivity and low loss tangent. The Ansoft HFSS, commercial program employee, using the finite element method, and was used for analysis of antennas studied in this work

Mudanças na ultra-estrutura da parede celular de mangas 'Tommy Atkins' tratadas com cloreto de cálcio na pré-colheita

Mangas 'Tommy Atkins' produzidas na região de Ibirá, São Paulo, foram pulverizadas na pré-colheita com cloreto de cálcio, nas concentrações de 0,0%, 2,5% e 5,0%, em três épocas de seu desenvolvimento (40; 60 e 90 dias após a floração) a fim de verificar a influência do cálcio na estrutura da parede celular destes frutos através de microscopia eletrônica de transmissão, imediatamente após a colheita e depois de 35 dias de armazenamento. Para fixar o material da polpa, utilizou-se metodologia descrita por Jacob e Gowanlock (1995). Nas condições experimentais, verificou-se que os frutos do tratamento-controle (sem cloreto de cálcio), no dia da colheita, já apresentavam desestruturação da parede celular e dissolução da lamela média (LM). A degradação da parede celular ocorre inicialmente na LM, levando à formação de espaços vazios bastante distintos, apresentando uma dissolução ainda maior, com o armazenamento prolongado (35 dias). Os frutos tratados com cloreto de cálcio a 5,0% apresentaram uma LM bem definida e ausência de espaços vazios, mesmo após o armazenamento, mostrando ser uma concentração efetiva na preservação da lamela média.

Análise do efeito do tempo da moagem de alta energia no tamanho de cristalito e microdeformação da rede cristalina do WC-Co

Hard metals are the composite developed in 1923 by Karl Schröter, with wide application because high hardness, wear resistance and toughness. It is compound by a brittle phase WC and a ductile phase Co. Mechanical properties of hardmetals are strongly dependent on the microstructure of the WC Co, and additionally affected by the microstructure of WC powders before sintering. An important feature is that the toughness and the hardness increase simultaneously with the refining of WC. Therefore, development of nanostructured WC Co hardmetal has been extensively studied. There are many methods to manufacture WC-Co hard metals, including spraying conversion process, co-precipitation, displacement reaction process, mechanochemical synthesis and high energy ball milling. High energy ball milling is a simple and efficient way of manufacturing the fine powder with nanostructure. In this process, the continuous impacts on the powders promote pronounced changes and the brittle phase is refined until nanometric scale, bring into ductile matrix, and this ductile phase is deformed, re-welded and hardened. The goal of this work was investigate the effects of highenergy milling time in the micro structural changes in the WC-Co particulate composite, particularly in the refinement of the crystallite size and lattice strain. The starting powders were WC (average particle size D50 0.87 μm) supplied by Wolfram, Berglau-u. Hutten - GMBH and Co (average particle size D50 0.93 μm) supplied by H.C.Starck. Mixing 90% WC and 10% Co in planetary ball milling at 2, 10, 20, 50, 70, 100 and 150 hours, BPR 15:1, 400 rpm. The starting powders and the milled particulate composite samples were characterized by X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) to identify phases and morphology. The crystallite size and lattice strain were measured by Rietveld s method. This procedure allowed obtaining more precise information about the influence of each one in the microstructure. The results show that high energy milling is efficient manufacturing process of WC-Co composite, and the milling time have great influence in the microstructure of the final particles, crushing and dispersing the finely WC nanometric order in the Co particles

Obtenção de cerâmicas à base de tricálcio fosfatos utilizando óxido de manganês como aditivo

The calcium phosphate ceramics have been very investigated as material for bone implants. The tricalcium phosphate (β-TCP) had a great potential for application in temporary implants like a resorbable bioceramic. This material presents a limitation in its sintering temperature due to occurrence of the allotropic transformation β → α at temperatures around 1200°C, not allowing the attainment of dense ceramic bodies. This transformation also causes cracks, what diminishes the mechanical strength, limiting its use to applications of low mechanical requests. This work studies the influence of the addition of manganese oxide in the sintering of β-TCP. Two processing routes were investigated. The first was the powder metallurgy conventional process. The test bodies (samples) were pressed and sintering at temperatures of 1200 and 1250°C. The second route was uniaxial hot pressing and its objective was to obtain samples with high relative density. The samples were physically characterized through density and porosity measurements. The thermal behavior was studied through dilatometric, thermal differential and thermogravimetric analysis. The mechanical properties were characterized by three point flexure test and Vickers microhardness measurements. The microstructure was analyzed by scanning electron microscopy. The addition of manganese oxide caused an improvement of the mechanical strength in relation to the material without additive and promoting the stabilization of β-TCP to greater temperatures

Fibras de licuri: um reforço vegetal alternativo de compósitos poliméricos

This research is based, at first, on the seeking of alternatives naturals reinforced in place of polymeric composites, also named reinforced plastics. Therein, this work starts with a whole licuri fiber micro structural characterization, as alternative proposal to polymeric composites. Licuri fiber is abundant on the Bahia state flora, native from a palm tree called Syagrus Coronata (Martius) Beccari. After, it was done only licuri fiber laminar composite developing studies, in order to know its behavior when impregnated with thermofix resin. The composite was developed in laminar structure shape (plate with a single layer of reinforcement) and produced industrially. The layer of reinforcement is a fabric-fiber unidirectional of licuri up in a manual loom. Their structure was made of polyester resin ortofitálica (unsaturated) only reinforced with licuri fibers. Fiber characterization studies were based on physical chemistry properties and their constitution. It was made by tension, scanning electron microscopy (SEM), x-ray diffraction (RDX) and thermal analyses (TG and DTA) tests, besides fiber chemistry analyses. Relating their mechanical properties of strength and hardness testing, they were determined through unit axial tension test and flexion in three points. A study in order to know fiber/matrix interface effects, in the final composites results, was required. To better understand the mechanical behavior of the composite, macroscopic and microscopic optical analysis of the fracture was performed

Utilização de resíduos de rochas ornamentais na produção de cerâmica branca

The marble and granite waste come from the process of mining of those ornamental rocks for use in the building industry. Brazil is one of the largest producers of blocks or finished products of ornamental rocks, extracting about 5.2 tons / year. The largest national producers are the states of Espírito Santo, Minas Gerais and Bahia which account for 80% of the Brazilian production. However, the waste total amount during processing of these blocks reaches 40% of the total. The use of the waste produced by this industry in white ceramics could be a form of disposition, because these materials, are thrownasa mud directly at decantation ponds, wastelands or in rivers, without any treatment. The present work has as main purpose to study the influence that reject of the ornamental rocks on the physical and mechanical properties of white ceramics. X-Ray characterizations of raw materials by were performed X-Ray fluorescence, X-Ray diffraction, granulometric, thermogravimetric and thermodiferencial analysis, five formulations were made (0, 10, 20, 30, 40% in granite weight) wich were burned at three temperatures: 1100°C, 1150°C and 1200ºC with 60 minutes of sorling time. After sintering, the samples were submitted to different analyser absorption of water, linear retraction, apparent porosity, apparent specific mass, flexival stronght, and scanning were obtained microscopy. Compatible technological properties within the limits demanded for the production of porcelainized stoneware

Estudo da oxidação superficial de ligas odontológicas de Ni-Cr em plasma pulsado para uso em restaurações metalocerâmicas

Metal ceramic restorations matches aesthetic and strength, and in your making occurs an interface oxide layer, wetting resulting and atomic and ionic interactions resulting between metal, oxide and porcelain. However, frequent clinical fails occurs in this restoration type, because lost homogeneous deposition oxide layer and lost interface bond. Thus, in this study, thought depositate homogeneous oxide films above Ni-Cr samples surfaces polite previously, at plasma oxide environment. Six samples was oxided at 300 and 400ºC at one hour, and two samples was oxided in a comum chamber at 900ºC, and then were characterized: optical microscopic, electronic microscopic, micro hardness, and X ray difratometry. Colors stripes were observed at six samples plasma oxided and a grey surface those comum oxided, thus like: hardness increase, and several oxides from basic metals (Ni-Cr)

Caracterização de cerâmicas porosas de alumina reforçada com zircônia produzidas pelo método da réplica

Porous ceramics have many applications: thermal insulation, catalytic support, materials to fire protection, filters, and others. There are many techniques to production of ceramic filters. One technique to obtain ceramic filters is the replication method. This method consists in the impregnation of polymeric foam with ceramic slurry followed by a heating treatment that will burn out the organic elements and sintering of the material, resulting of a replication of the original foam. To perform their functions ceramic filters must satisfy mechanical requirements and permeability parameters (darcian k1 and no-darcian k2). The permeability and the strength of the ceramic material are dependent of the pore size and pore distribution. To the use at high temperatures the evaluation of mechanical properties in these temperatures is necessary. In this work the mechanical behavior of two commercial porous ceramics (10 and 40 poros per inch) was studied these materials were submitted to compression and four-point flexure test (room temperature, at 1000 °C, after thermal shock). Density and porosity measurements, permeability tests and microstructural analysis by scanning electronic microscopy (SEM) were realized. The Results showed that the decrease of mechanical strength of these materials, when submitted to thermal shock, occur for propagation of new cracks from cracks pre-existing and the permeability depends of the pore size