Ristikkorakenteisen hihnakuljetinsillan mitoitustyökalun kehittäminen

Hihnakuljettimia käytetään muun muassa voimalaitos- ja sellutehdasympäristöissä kuljettamaan kiinteää polttoainetta tai haketta pitkiä matkoja. Pitkät hihnakuljettimet asennetaan yleensä teräsristikoista rakennettujen kuljetinsiltojen sisään. Kuljetinsilta toimii siis hihnakuljettimen ja hoitokäytävän runkona sekä suojaa kuljetinta ja kuljetettavaa materiaalia säältä. Tässä diplomityössä on laadittu mitoitustyökalu, jolla voidaan nopeasti mitoittaa ristikkorakenteisen hihnakuljetinsillan sauvat sekä määrittää rakenteen massa. Laskentaohjelma on toteutettu Microsoft Excel -taulukkolaskentana. Sillan poikkileikkaus voi olla suljettu symmetrinen umpirakenne tai avorakenne, jossa on ulokkeellinen hoitotaso. Ristikon sauvat ovat RHS-putkia. Rakenteeseen voi vaikuttaa jatkuvia kuormia, pistekuormia sekä näistä johdetut, ekvivalenttiin staattiseen voimaan perustuvat maanjäristyskuormat. Diplomityössä on perehdytty mitoitustyökalussa sovellettuihin teorioihin. Voimasuureiden laskenta perustuu 2-tukisina palkkeina käsiteltävien siltalohkojen ratkaisuun ja palkkianalogiaan, jossa ristikon sauvavoimat ratkaistaan käsittelemällä ristikkoa palkkina. Sauvojen kestävyyden laskenta perustuu SFS-EN 1993-1-1 -normiin, joka on osa Eurocode -rakennesuunnittelunormistoa. Lisäksi työssä on käsitelty ristikkoliitosten mitoitusta SFS-EN 1993-1-8 mukaan. Mitoitusohjelman toimivuutta on testattu tarkastelemalla esimerkkisiltaa laaditulla mitoituspohjalla ja Autodesk Robot Professional 2013 -FE-analyysiohjelmisuolla. Tulosten perusteella mitoitustyökalua voidaan käyttää ainakin tarjousvaiheen nopeisiin tarkasteluihin ja omamassan määritykseen, mutta myös lopulliseen mitoitukseen, mikäli hyväksytään konservatiivinen mitoitus.

Cesarean section - short term maternal complications related to the mode of delivery

Cesarean section (CS) is the most common major surgery performed on women worldwide. CS can save the life of the mother or the fetus, but is associated with the typical complications of any major surgery: hemorrhage, infection, venous thromboembolism and complications of anesthesia, sometimes leading to maternal death. Recently there have been several reports from well resourced countries on increased severe maternal morbidity and even mortality. Increased rates of CS, obesity and older mothers may explain this rise. The aim of this thesis is to study the rates and risk factors of short term maternal complications associated with CS. Also, we compared maternal morbidity by mode of delivery and over time. The complication rates were assessed in a prospective study involving 2496 CS performed in the 12 largest delivery units in Finland in 2005. The rates of severe complications were studied by mode of delivery in a register-based study comparing national cohorts in 1997 and 2002. The impact of several risk factors on severe maternal morbidity by mode of delivery was studied in a register-based study of all singleton deliveries in 2007-2011. In the prospective study, 27% of the women who underwent CS had one or more intraoperative or postoperative complications during their hospital stay, and 10% had a severe complication. In the register-based study the incidence of life-threatening maternal complications was 7.6 in 1000 deliveries. The incidence was lowest for vaginal delivery (VD), followed by instrumental VD and elective CS, and highest in emergency CS. An attempt of VD, including the risks associated with emergency CS, seems to be the safest mode of delivery, even for most high-risk women.

Radar cross-section measurement using the Doppler effect

In this Master Thesis we discuss issues related to the measurement of the effective scattering surface, based on the Doppler Effect. Modeling of the detected signal was made. Narrowband signal filtering using low-frequency amplifier was observed. Parameters of the proposed horn antennas were studied; radar cross section charts for three different objects were received.

Why are the rates of cesarean section in Brazil higher in more developed cities than in less developed ones?

The objective of the present study was to investigate factors associated with cesarean sections in two cities located in different regions of Brazil and to determine factors that explain the higher cesarean section rate in the more developed city, Ribeirão Preto, compared to the less developed one, São Luís. Data from two cohort studies comprising 2846 women in Ribeirão Preto in 1994, and 2443 women in São Luís in 1997/1998 were used. Adjusted and non-adjusted risk estimates were calculated using a Poisson regression model. The cesarean section rate was 33.7% in São Luís and 50.8% in Ribeirão Preto. Adjusted analysis in a joint sequential model revealed a 51% higher risk of cesarean section in Ribeirão Preto compared to São Luís (prevalence rate ratio (PRR) = 1.51). Adjustment for category of hospital admission reduced the PRR to 1.09, i.e., this variable explained 82% of the difference in the cesarean section rate between the two cities. Adjustment for the variable "the same physician for prenatal care and delivery" reduced the PRR to 1.07, with the "physician" factor explaining 86% of the difference between rates. When simultaneously adjusted for the two variables, the PRR decreased to 1.05, with these two variables explaining 90% of the difference in the cesarean section rate between the two cities, and the difference was no longer significant. The difference in the cesarean section rate between the two Brazilian cities, one more and one less developed, was mainly explained by the physician factor and, to a lesser extent, by the category of hospital admission.

The effect of epidural and general anesthesia on newborn rectal temperature at elective cesarean section

Both epidural and general anesthesia can impair thermoregulatory mechanisms during surgery. However, there is lack of information about the effects of different methods of anesthesia on newborn temperature. The purpose of this study was to determine whether there are differences in newborn rectal temperature related to type of anesthesia. Sixty-three pregnant women were randomly assigned to receive general or epidural anesthesia. Maternal core temperature was measured three times with a rectal probe just before anesthesia, at the beginning of surgery and at delivery. In addition, umbilical vein blood was sampled for pH. The rectal temperatures of the babies were recorded immediately after delivery, and Apgar scores were determined 1, 5, and 10 min after birth. The duration of anesthesia and the volume of intravenous fluid given during the procedure (833 ± 144 vs 420 ± 215 mL) were significantly higher in the epidural group than in the general anesthesia group (P < 0.0001). Maternal rectal temperatures were not different in both groups at all measurements. In contrast, newborn rectal temperatures were lower in the epidural anesthesia group than in the general anesthesia group (37.4 ± 0.3 vs 37.6 ± 0.3°C; P < 0.05) immediately after birth. Furthermore, the umbilical vein pH value (7.31 ± 0.05 vs 7.33 ± 0.01; P < 0.05) and Apgar scores at the 1st-min measurement (8.0 ± 0.9 vs 8.5 ± 0.7; P < 0.05) were lower in the epidural anesthesia group than in the general anesthesia group. Since epidural anesthesia requires more iv fluid infusion and a longer time for cesarean section, it involves a risk of a mild temperature reduction for the baby which, however, did not reach the limits of hypothermia.

Effect of heat input on the mechanical properties of welded joints in high strength steels

Experiments were carried out to determine the properties of the welded joints in 8mm thick high-strength steels produced by quenching and tempering and thermomechanical rolling with accelerated cooling (tensile strength 821–835 MPa). The dependence of the strength, elongation, hardness, impact energy and crack opening displacement on the heat input in the range 1.0–0.7 kJ mm21 was determined. The results show that the dependence of the strength of the welded joints decreases and that of the elongation increases. The heat input has only a slight effect on the impact energy and crack opening displacement in the heat-affected zone.

Thick Section Laser Beam Welding of Structural Steels: Methods for Improving Welding Efficiency

Laser beam welding (LBW) is applicable for a wide range of industrial sectors and has a history of fifty years. However, it is considered an unusual method with applications typically limited to welding of thin sheet metal. With a new generation of high power lasers there has been a renewed interest in thick section LBW (also known as keyhole laser welding). There was a growing body of publications during 2001-2011 that indicates an increasing interest in laser welding for many industrial applications, and in last ten years, an increasing number of studies have examined the ways to increase the efficiency of the process. Expanding the thickness range and efficiency of LBW makes the process a possibility for industrial applications dealing with thick metal welding: shipbuilding, offshore structures, pipelines, power plants and other industries. The advantages provided by LBW, such as high process speed, high productivity, and low heat input, may revolutionize these industries and significantly reduce the process costs. The research to date has focused on either increasing the efficiency via optimizing process parameters, or on the process fundamentals, rather than on process and workpiece modifications. The argument of this thesis is that the efficiency of the laser beam process can be increased in a straightforward way in the workshop conditions. Throughout this dissertation, the term “efficiency” is used to refer to welding process efficiency, specifically, an increase in efficiency refers an increase in weld’s penetration depth without increasing laser power level or decreasing welding speed. These methods are: modifications of the workpiece – edge surface roughness and air gap between the joining plates; modification of the ambient conditions – local reduction of the pressure in the welding zone; modification of the welding process – preheating of the welding zone. Approaches to improve the efficiency are analyzed and compared both separately and combined. These experimentally proven methods confirm previous findings and contribute additional evidence which expand the opportunities for laser beam welding applications. The focus of this research was primarily on the effects of edge surface roughness preparation and pre-set air gap between the plates on weld quality and penetration depth. To date, there has been no reliable evidence that such modifications of the workpiece give a positive effect on the welding efficiency. Other methods were tested in combination with the two methods mentioned above. The most promising - combining with reduced pressure method - resulted in at least 100% increase in efficiency. The results of this thesis support the idea that joining those methods in one modified process will provide the modern engineering with a sufficient tool for many novel applications with potential benefits to a range of industries.

Effect of loading type on the fatigue strength of symmetric and asymmetric welded joints made of ultra high strength steel

In this study, finite element analyses and experimental tests are carried out in order to investigate the effect of loading type and symmetry on the fatigue strength of three different non-load carrying welded joints. The current codes and recommendations do not give explicit instructions how to consider degree of bending in loading and the effect of symmetry in the fatigue assessment of welded joints. The fatigue assessment is done by using effective notch stress method and linear elastic fracture mechanics. Transverse attachment and cover plate joints are analyzed by using 2D plane strain element models in FEMAP/NxNastran and Franc2D software and longitudinal gusset case is analyzed by using solid element models in Abaqus and Abaqus/XFEM software. By means of the evaluated effective notch stress range and stress intensity factor range, the nominal fatigue strength is assessed. Experimental tests consist of the fatigue tests of transverse attachment joints with total amount of 12 specimens. In the tests, the effect of both loading type and symmetry on the fatigue strength is studied. Finite element analyses showed that the fatigue strength of asymmetric joint is higher in tensile loading and the fatigue strength of symmetric joint is higher in bending loading in terms of nominal and hot spot stress methods. Linear elastic fracture mechanics indicated that bending reduces stress intensity factors when the crack size is relatively large since the normal stress decreases at the crack tip due to the stress gradient. Under tensile loading, experimental tests corresponded with finite element analyzes. Still, the fatigue tested joints subjected to bending showed the bending increased the fatigue strength of non-load carrying welded joints and the fatigue test results did not fully agree with the fatigue assessment. According to the results, it can be concluded that in tensile loading, the symmetry of joint distinctly affects on the fatigue strength. The fatigue life assessment of bending loaded joints is challenging since it depends on whether the crack initiation or propagation is predominant.

Réunion des sociétés savantes des départements à la Sorbonne.... Section des beaux-arts / Ministère de l'instruction publique...

1905 (SESSION29).

Réunion des sociétés savantes des départements à la Sorbonne.... Section des beaux-arts / Ministère de l'instruction publique...

1878.

Réunion des sociétés savantes des départements à la Sorbonne.... Section des beaux-arts / Ministère de l'instruction publique...

1901 (SESSION25).