Effects of unconfined concrete strength on FRP confinement of concrete

Research has shown that fibre reinforced polymer (FRP) wraps are effective for strengthening concrete columns for increased axial and flexural load and deformation capacity, and this technique is now used around the world. The experimental study presented in this paper is focused on the mechanics of FRP confined concrete, with a particular emphasis on the influence of the unconfined concrete compressive strength on confinement effectiveness and hoop strain efficiency. An experimental programme was undertaken to study the compressive strength and stress-strain behaviour of unconfined and FRP confined concrete cylinders of different concrete strength but otherwise similar mix designs, aggregates, and constituents. This was accomplished by varying only the water-to-cement ratio during concrete mixing operations. Through the use of high-resolution digital image correlation to measure both axial and hoop strains, the observations yield insights into the mechanics of FRP confinement of concretes of similar composition but with varying unconfined concrete compressive strength.

Predicting impact damage, residual strength and crashworthiness of composite structures

The development of the latest generation of wide-body carbon-fibre composite passenger aircraft has heralded a new era in the utilisation of these materials. The premise of superior specific strength and stiffness, corrosion and fatigue resistance, is tempered by high development costs, slow production rates and lengthy and expensive certification programmes. Substantial effort is currently being directed towards the development of new modelling and simulation tools, at all levels of the development cycle, to mitigate these shortcomings. One of the primary challenges is to reduce the extent of physical testing, in the certification process, by adopting a ‘certification by simulation’ approach. In essence, this aspirational objective requires the ability to reliably predict the evolution and progression of damage in composites. The aerospace industry has been at the forefront of developing advanced composites modelling tools. As the automotive industry transitions towards the increased use of composites in mass-produced vehicles, similar challenges in the modelling of composites will need to be addressed, particularly in the reliable prediction of crashworthiness. While thermoset composites have dominated the aerospace industry, thermoplastics composites are likely to emerge as the preferred solution for meeting the high-volume production demands of passenger road vehicles. This keynote presentation will outline recent progress and current challenges in the development of finite-element-based predictive modelling tools for capturing impact damage, residual strength and energy absorption capacity of thermoset and thermoplastic composites for crashworthiness assessments.

The Educational and Employment Aspirations of Adolescents from Areas of High Deprivation in London

Adolescents from areas of high deprivation are often assumed to have low aspirations for the future. However, recent research has suggested otherwise and there have been calls for more substantial investigation into the relationship between poverty and aspiration. This article reports levels and variation in aspiration from 1,214 adolescents (49.5% male; 50.5% female) living in areas of high deprivation across 20 London boroughs. A strength of this study is our large and diverse population of low socio-economic status (SES) adolescents, comprising of white British (22%), black African (21%), black Caribbean (9%), Indian/Pakistani/Bangladeshi/Other Asian (24%), mixed ethnicity (9%), and 15% defining themselves as Other. Our measures indicated a high group level of reported aspiration with notable variations. Females reported higher educational (but not occupational) aspirations than males; white British students reported lower educational and occupational aspirations than other ethnic groups; and black African children reported the highest educational aspirations. Perceived parental support for education had the largest positive association with aspirations. In contrast to previous findings from studies carried out in the United States, aspirations were found to be negatively associated with perceptions of school and school peer environment. These measures explored feelings of safety, happiness and belonging within the school environment and school peer group. We discuss possible explanations for this unexpected finding within our population of adolescents from UK state schools and how it might affect future policy interventions. This study makes an important contribution to the literature on adolescent aspirations because of the unique nature of the data sample and the multiple domains of functioning and aspiration measured.

Tensile behaviour of a structural adhesive at high temperatures by the extended finite element method

Component joining is typically performed by welding, fastening, or adhesive-bonding. For bonded aerospace applications, adhesives must withstand high-temperatures (200°C or above, depending on the application), which implies their mechanical characterization under identical conditions. The extended finite element method (XFEM) is an enhancement of the finite element method (FEM) that can be used for the strength prediction of bonded structures. This work proposes and validates damage laws for a thin layer of an epoxy adhesive at room temperature (RT), 100, 150, and 200°C using the XFEM. The fracture toughness (G Ic ) and maximum load ( ); in pure tensile loading were defined by testing double-cantilever beam (DCB) and bulk tensile specimens, respectively, which permitted building the damage laws for each temperature. The bulk test results revealed that decreased gradually with the temperature. On the other hand, the value of G Ic of the adhesive, extracted from the DCB data, was shown to be relatively insensitive to temperature up to the glass transition temperature (T g ), while above T g (at 200°C) a great reduction took place. The output of the DCB numerical simulations for the various temperatures showed a good agreement with the experimental results, which validated the obtained data for strength prediction of bonded joints in tension. By the obtained results, the XFEM proved to be an alternative for the accurate strength prediction of bonded structures.

Shear strength of adhesively bonded polyolefins with minimal surface preparation

Interest in polyethylene and polypropylene bonding has increased in the last years. However, adhesive joints with adherends which are of low surface energy and which are chemically inert present several difficulties. Generally, their high degree of chemical resistance to solvents and dissimilar solubility parameters limit the usefulness of solvent bonding as a viable assembly technique. One successful approach to adhesive bonding of these materials involves proper selection of surface pre-treatment prior to bonding. With the correct pre-treatment it is possible to glue these materials with one or more of several adhesives required by the applications involved. A second approach is the use of adhesives without surface pre-treatment, such as hot melts, high tack pressure-sensitive adhesives, solvent-based specialty adhesives and, more recently, structural acrylic adhesives as such 3M DP-8005® and Loctite 3030®. In this paper, the shear strengths of two acrylic adhesives were evaluated using the lap shear test method ASTM D3163 and the block shear test method ASTM D4501. Two different industrial polyolefins (polyethylene and polypropylene) were used for adherends. However, the focus of this study was to measure the shear strength of polyethylene joints with acrylic adhesives. The effect of abrasion was also studied. Some test specimens were manually abraded using 180 and 320 grade abrasive paper. An additional goal of this work was to examine the effect of temperature and moisture on mechanical strength of adhesive joints.

Effects of dietary restraint and oral contraceptives on bone strength and bone turnover in young women

ABSTRACT Introduction The purpose of this study was to assess specific osteoporosis-related health behaviours and physiological outcomes including daily calcium intake, physical activity levels, bone strength, as assessed by quantitative ultrasound, and bone turnover among women between the ages of 18 and 25. Respective differences on relevant study variables, based on dietary restraint and oral contraceptive use were also examined. Methods One hundred women (20.6 ± 0.2 years of age) volunteered to participate in the study. Informed written consent was obtained by all subjects prior to participation. The study and all related procedures were approved by the Brock University Research Ethics Board. Body mass, height, relative body fat, as well as chest, waist and hip circumferences were measured using standard procedures. The 10-item restrained eating subscale of the Dutch Eating Behaviour Questionnaire (DEBQ) was used to assess dietary restraint (van Strien et al., 1986). Daily calcium intake was assessed by the Rapid Assessment Method (RAM) (Hertzler & Frary 1994). Weekly physical activity was documented by the 4-item Godin Leisure-Time Exercise Questionnaire (Godin & Shephard 1985). Bone strength was determined from the speed of sound (SOS) as measured by QUS (Sunlight 7000S). SOS measurements (m/s) were taken of the dominant and non-dominant sides of the distal one third of the radius and the mid-shaft of the tibia. Resting blood samples were collected from all subjects between 9am and 12pm, in order to evaluate the impact of lifestyle factors on biochemical markers of bone turnover. Blood was collected during the early follicular phase of the menstrual cycle (approximately days 1-5) for all subjects. Samples were centrifliged and the serum or plasma was aliquoted into separate tubes and stored at -80°C until analysis. The bone formation markers measured were Osteocalcin (OC), bone specific alkaline phosphatase (BAP) and 25-OH vitamin D. The bone resorption markers measured were the carboxy (CTx) and amino (NTx) terminal telopeptides of type-I collagen crosslinks. All markers were assessed by ELISA. Subjects were divided into high (HDR) and low dietary restrainers (LDR) based on the median DEBQ score, and also into users (BC) and non-users (nBC) of oral contraceptives. A series of multiple one way ANOVA's were then conducted to identify differences between each set of groups for all relevant variables. A two-way ANOVA analysis was used to explore significant interactions between dietary restraint and use of oral contraceptives while a univariate follow-up analysis was also performed when appropriate. Pearson Product Moment Correlations were used to determine relationships among study variables. Results HDR had significantly higher BMI, %BF and circumference measures but lower daily calcium intake than LDR. There were no significant differences in physical activity levels between HDR and LDR. No significant differences were found between BC and nBC in body composition, calcium intake and physical activity. HDR had significantly lower tibial SOS scores than LDR in both the dominant and non-dominant sites. The post-hoc analysis showed that within the non-birth control group, the HDR had significantly lower tibial SOS scores of bone strength when compared to the LDR but Aere were no significant differences found between the two dietary restraint groups for those currently on birth control. HDR had significantly lower levels of OC than LDR and the BC group had lower levels of BAP than the nBC group. Consistently, the follow-up analysis revealed that within those not on birth control, subjects who were classified as HDR had significantly (f*<0.05) lower levels of OC when compared with LDR but no significant differences were observed in bone turnover between the two dietary restraint groups for those currently on birth control. Physical activity was not correlated with SOS scores and bone turnover markers possibly due to the low physical activity variability in this group of women. Conclusion This is the first study to examine the effects of dietary restraint on bone strength and turnover among this population of women. The most important finding of this study was that bone strength and turnover are negatively influenced by dietary restraint independent of relative body fat. In general, the results of the present thesis suggest that dietary restraint, oral contraceptive use, as well as low daily calcium intake and low physical activity levels were widespread behaviours among this population of college-aged women. The young women who were using dietary restraint as a strategy to lose weight, and thus were in the HDR group, despite their higher relative body fat and weight, had lower scores of bone strength and lower levels of markers of bone turnover compared to the low dietary restrainers. Additionally, bone turnover seemed to be negatively affected by oral contraceptives, while bone strength, as assessed by QUS, seemed unaffected by their use in this population of young women. Physical activity (weekly energy expenditure), on the other hand, was not associated with either bone strength or bone tiimover possibly due to the low variability of this variable in this population of young Canadian women.

Completing the picture: the effects of video game practice on verbal and performance I.Q. scores in high functioning children

The strength and nature of the video game practice effect on tests of visual and perceptual skills were examined using high functioning Grades Four and Five students who had been tested with the WISC-R .for the purpose of gifted identification and placement. The control group, who did not own and .play video games on a sustained basis, and the experimental group, who did own a video game system and had some mastery of video games, including the -Nintendo game, "Tetris", were each composed of 18 juniorg:r;-ade students and were chosen from pre-existing conditions. The experimental group corresponded to the control group in terms of age, sex, and community. Data on the Verbal and Performance I.Q. Scores were· collected for both groups and the author was interested in the difference between the Verbal and Performance Scores within each group, anticipating a P > V outcome for the experimental group. The results showed a significant P > V difference in the experimental, video game playing group, as expected, but no significant difference between the Performance $cores of the control and experimental groups. The results, thus, indicated lower Verbal I.Q. Scores in the experimental group relat'ive to 'the control group.' The study conclu~ed that information about a sUbject's video game experience and "learhing style pref~rence is important for a clear interpretation of the Verbal and Performance I.Q. Scores of the WISC-R. Although the time spent on video game play may, 'indeed, increase P~rformance Scores relative to Verbal Scores for an individual, the possibilities exist that the time borrowed and spent away from language based activities may retard verbal growth and/or that the cognitive style associated with some Performance I.Q.subtests may have a negative effect on the approach to the tasks on the Verbal I.Q. Scale. The study also discussed the possibility that exposure to ,the video game experience, in pre-puberty, can provide spatial instruction which will result in improved spatial skills. strong spatial skills have been linked to improved performance and preference in mathematics, science, and engineering and it was suggested that appropriate video game play might be a way to involve girls more in the fields of mathematics and science.

Effect of a high fat maternal diet on body composition and bone development in male offspring

Direct high fat (HF) feeding has adverse effects on body composition and bone development in rodents. However, it is unclear whether maternal HF feeding has similar effects in male rat offspring. The objectives of this thesis were to determine if maternal HF feeding altered body composition, plasma hormones, bone development, and bone fatty acid composition in male offspring at weaning and 3 months of age. Maternal HF feeding increased bone mass and altered femur fatty acid composition at weaning, without differences in fat mass, lean mass, plasma hormones, or bone mass (femur or lumbar vertebrae). However, early differences did not persist at 3 months of age or contribute to lower bone strength – following consumption of a control diet post-weaning. These findings suggest that maternal HF feeding can alter body composition and bone development in weanling male offspring, without long-lasting effects if a healthy control diet is consumed post-weaning.

Maternal High Fat Feeding: Impact of Female Offspring Body Composition and Bone Health

High fat diet (HFD) consumption in rodents alters body composition and weakens bones. Whether female offspring of mothers consuming a HFD are similarly affected at weaning and early adulthood is unclear. This research determined whether maternal HFD contributes to long-lasting alterations in body composition and bone health of female offspring. Rats were fed control or HFD for 10 weeks prior to and throughout pregnancy and lactation. Female offspring were studied at weaning or 3 months of age (consumed control diet). Main findings in female offspring: maternal HFD decreased lean mass, increased fat mass and femoral BMD at weaning, but not at 3 months; weanling femoral lipid composition reflected maternal diet, persisting to 3 months of age (decreased total and n6 polyunsaturates, increased saturates); and no differences in femoral strength at 3 months. In summary, 3 month old female offspring have similar body composition and bone health regardless of maternal diet.

Indirect Bonding Method: in vitro Comparison of the Shear Bond Strength between Metallic Orthodontic Brackets and Different Porcelain Surface Preparations

Introduction : La force d’adhésion à l'interface métal-céramique avec les résines auto-polymérisantes destinées au collage indirect des boîtiers orthodontiques n'a pas été évaluée à ce jour et un protocole clinique basé sur la littérature scientifique est inexistant. Objectifs : 1) Comparer la force de cisaillement maximale entre des boîtiers métalliques et des surfaces en porcelaine préparées selon différentes méthodes; 2) Suggérer un protocole clinique efficace et prévisible. Matériel et méthodes : Quatre-vingt-dix disques en leucite (6 groupes; n = 15/groupe) ont été préparés selon 6 combinaisons de traitements de surface : mécaniques (+ / - fraisage pour créer les rugosités) et chimiques (acide fluorhydrique, apprêt, silane). Des bases en résine composite Transbond XT (3M Unitek, Monrovia, California) faites sur mesure ont été collées avec le système de résine adhésive auto-polymérisante Sondhi A + B Rapid Set (3M Unitek, Monrovia, California). Les échantillons ont été préservés (H2O/24hrs), thermocyclés (500 cycles) et testés en cisaillement (Instron, Norwood, Massachusetts). Des mesures d’Index d’adhésif résiduel (IAR) ont été compilées. Des tests ANOVAs ont été réalisés sur les rangs étant donné que les données suivaient une distribution anormale et ont été ajustés selon Tukey. Un Kruskall-Wallis, U-Mann Whitney par comparaison pairée et une analyse de Weibull ont aussi été réalisés. Résultats : Les médianes des groupes varient entre 17.0 MPa (- fraisage + acide fluorhydrique) à 26.7 MPa (- fraisage + acide fluorhydrique + silane). Le fraisage en surface ne semble pas affecter l’adhésion. La combinaison chimique (- fraisage + silane + apprêt) a démontré des forces de cisaillement significativement plus élevées que le traitement avec (- fraisage + acide fluorhydrique), p<0,05, tout en possédant des forces similaires au protocole typiquement suggéré à l’acide fluorhydrique suivi d’une application de silane, l’équivalence de (- fraisage + acide fluorhydrique + silane). Les mesures d’IAR sont significativement plus basses dans le groupe (- fraisage + acide fluorhydrique) en comparaison avec celles des 5 autres groupes, avec p<0,05. Malheureusement, ces 5 groupes ont des taux de fracture élévés de 80 à 100% suite à la décimentation des boîtiers. Conclusion : Toutes les combinaisons de traitement de surface testées offrent une force d’adhésion cliniquement suffisante pour accomplir les mouvements dentaires en orthodontie. Une application de silane suivie d’un apprêt est forte intéressante, car elle est simple à appliquer cliniquement tout en permettant une excellente adhésion. Il faut cependant avertir les patients qu’il y a un risque de fracture des restorations en céramique lorsque vient le moment d’enlever les broches. Si la priorité est de diminuer le risque d’endommager la porcelaine, un mordançage seul à l’acide hydrofluorique sera suffisant.

Synthesis of polyelectrolyte brushes on silica-based substrates through surface-initiated polymerization : brush characterization and responsiveness to variation in pH and ionic strength

Les brosses de polyélectrolytes font l’objet d’une attention particulière pour de nombreuses applications car elles présentent la capacité de changer de conformation et, par conséquent, de propriétés de surface en réponse aux conditions environnementales appliquées. Le contrôle des principaux paramètres de ces brosses telles que l'épaisseur, la composition et l'architecture macromoléculaire, est essentiel pour obtenir des polymères greffés bien définis. Ceci est possible avec la Polymérisation Radicalaire par Transfert d’Atomes - Initiée à partir de la Surface (PRTA-IS), qui permet la synthèse de brosses polymériques de manière contrôlée à partir d’une couche d'amorceurs immobilisés de manière covalente sur une surface. Le premier exemple d’une synthèse directe de brosses de poly(acide acrylique) (PAA) par polymérisation radicalaire dans l’eau a été démontré. Par greffage d’un marqueur fluorescent aux brosses de PAA et via l’utilisation de la microscopie de fluorescence par réflexion totale interne, le dégreffage du PAA en temps réel a pu être investigué. Des conditions environnementales de pH ≥ 9,5 en présence de sel, se sont avérées critiques pour la stabilité de la liaison substrat-amorceur, conduisant au dégreffage du polymère. Afin de protéger de l’hydrolyse cette liaison substrat-amorceur sensible et prévenir le dégreffage non souhaité du polymère, un espaceur hydrophobique de polystyrène (PS) a été inséré entre l'amorceur et le bloc de PAA stimuli-répondant. Les brosses de PS-PAA obtenues étaient stables pour des conditions extrêmes de pH et de force ionique. La réponse de ces brosses de copolymère bloc a été étudiée in situ par ellipsométrie, et le changement réversible de conformation collapsée à étirée, induit par les variations de pH a été démontré. De plus, des différences de conformation provenant des interactions du bloc de PAA avec des ions métalliques de valence variable ont été obtenues. Le copolymère bloc étudié semble donc prometteur pour la conception de matériaux répondant rapidement a divers stimuli. Par la suite, il a été démontré qu’un acide phosphonique pouvait être employé en tant qu’ amorceur PRTA-IS comme alternative aux organosilanes. Cet amorceur phosphonate a été greffé pour la première fois avec succès sur des substrats de silice et une PRTA-IS en milieux aqueux a permis la synthèse de brosses de PAA et de poly(sulfopropyl méthacrylate). La résistance accrue à l’hydrolyse de la liaison Sisubstrat-O- Pamorceur a été confirmée pour une large gamme de pH 7,5 à 10,5 et a permis l’étude des propriétés de friction des brosses de PAA sous différentes conditions expérimentales par mesure de forces de surface. Malgré la stabilité des brosses de PAA à haute charge appliquée, les études des propriétés de friction ne révèlent pas de changement significatif du coefficient de friction en fonction du pH et de la force ionique.

A Study Of The Strength And Compressibility Characteristics Of Cochin Marine Clays

With the advent of urbanisation and consequent search for more and more habitable land, it was imperative that the large tracts of marine clays, considered inhabitable earlier, had to be reclaimed and developed. These marine clays, wellknown for its high compressibility and poor shear strength, posed numerous problems to the builders and Cochin was no exception. It is only less than a decade since active research work was initiated on marine clays in general and Cochin marine clays in particular. Eventhough some systematic studies are available on compressibility characteristics, attempts to study the shear strength aspects and development of techniques to improve it have been very limited. This work is an investigation on the consolidation and shear strength characteristics of Cochin marine clays including methods to improve the same

Rice husk ash – A valuable reinforcement for high density polyethylene

This paper presents the results of a study on the use of rice husk ash (RHA) for property modification of high density polyethylene (HDPE). Rice husk is a waste product of the rice processing industry. It is used widely as a fuel which results in large quantities of RHA. Here, the characterization of RHA has been done with the help of X-ray diffraction (XRD), Inductively Coupled Plasma Atomic Emission Spectroscopy (ICPAES), light scattering based particle size analysis, Fourier transform infrared spectroscopy (FTIR) and Scanning Electron Microscope (SEM). Most reports suggest that RHA when blended directly with polymers without polar groups does not improve the properties of the polymer substantially. In this study RHA is blended with HDPE in the presence of a compatibilizer. The compatibilized HDPE-RHA blend has a tensile strength about 18% higher than that of virgin HDPE. The elongation-at-break is also higher for the compatibilized blend. TGA studies reveal that uncompatibilized as well as compatibilized HDPERHA composites have excellent thermal stability. The results prove that RHA is a valuable reinforcing material for HDPE and the environmental pollution arising from RHA can be eliminated in a profitable way by this technique.

Microwave exfoliated reduced graphene oxide epoxy nanocomposites for high performance applications

Graphene has captured the attention of scientific community due to recently emerging high performance applications. Hence, studying its reinforcing effects on epoxy resin is a significant step. In this study, microwave exfoliated reduced graphene oxide (MERGO) was prepared from natural graphite for subsequent fabrication of epoxy nanocomposites using triethylenetetramine (TETA) as a curing agent via insitu polymerization. Thermogravimetric analysis (TGA), X-ray diffraction (XRD), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), C13 NMR spectroscopy, X-ray photoelectron spectroscopy (XPS) and ultravioletevisible (UVevis) spectroscopy were employed to confirm the simultaneous reduction and exfoliation of graphene oxide. The reinforcing effect of MERGO on epoxy resin was explored by investigating its static mechanical properties and dynamic mechanical analysis (DMA) at MERGO loadings of 0 to 0.5 phr. The micro-structure of epoxy/MERGO nanocomposites was investigated using scanning electron microscope (SEM), transmission electron microscope (TEM) and XRD techniques. The present work reports an enhancement of 32%, 103% and 85% in tensile, impact and flexural strength respectively of epoxy by the addition of even 0.25 phr MERGO. At this loading elastic and flexural moduli also increased by 10% and 65%, respectively. Single-edge-notch three-point-Bending (SEN-TPB) fracture toughness (KIC) measurements were carried out where a 63% increase was observed by the introduction of 0.25 phr MERGO. The interfacial interactions brought about by graphene also benefited the dynamic mechanical properties to a large extent in the form of a significant enhancement in storage modulus and slightly improved glass transition temperature. Considerable improvements were also detected in dielectric properties. The epoxy nanocomposite also attained an ac conductivity of 10 5 S/m and a remarkable increase in dielectric constant. The simple and cost effective way of graphene synthesis for the fabrication of epoxy/MERGO nanocomposites may be extended to the preparation of other MERGO based polymer nanocomposites. This remarkable class of materials has thrown open enormous opportunities for developing conductive adhesives and in microelectronics

Modification of Polypropylene/High Density Polyethylene Blend Using Nanokaolinite Clay and E-Glass Fibre: Preparation, Characterization and Micromechanical Modelling

Upgrading two widely used standard plastics, polypropylene (PP) and high density polyethylene (HDPE), and generating a variety of useful engineering materials based on these blends have been the main objective of this study. Upgradation was effected by using nanomodifiers and/or fibrous modifiers. PP and HDPE were selected for modification due to their attractive inherent properties and wide spectrum of use. Blending is the engineered method of producing new materials with tailor made properties. It has the advantages of both the materials. PP has high tensile and flexural strength and the HDPE acts as an impact modifier in the resultant blend. Hence an optimized blend of PP and HDPE was selected as the matrix material for upgradation. Nanokaolinite clay and E-glass fibre were chosen for modifying PP/HDPE blend. As the first stage of the work, the mechanical, thermal, morphological, rheological, dynamic mechanical and crystallization characteristics of the polymer nanocomposites prepared with PP/HDPE blend and different surface modified nanokaolinite clay were analyzed. As the second stage of the work, the effect of simultaneous inclusion of nanokaolinite clay (both N100A and N100) and short glass fibres are investigated. The presence of nanofiller has increased the properties of hybrid composites to a greater extent than micro composites. As the last stage, micromechanical modeling of both nano and hybrid A composite is carried out to analyze the behavior of the composite under load bearing conditions. These theoretical analyses indicate that the polymer-nanoclay interfacial characteristics partially converge to a state of perfect interfacial bonding (Takayanagi model) with an iso-stress (Reuss IROM) response. In the case of hybrid composites the experimental data follows the trend of Halpin-Tsai model. This implies that matrix and filler experience varying amount of strain and interfacial adhesion between filler and matrix and also between the two fillers which play a vital role in determining the modulus of the hybrid composites.A significant observation from this study is that the requirement of higher fibre loading for efficient reinforcement of polymers can be substantially reduced by the presence of nanofiller together with much lower fibre content in the composite. Hybrid composites with both nanokaolinite clay and micron sized E-glass fibre as reinforcements in PP/HDPE matrix will generate a novel class of high performance, cost effective engineering material.