Effect of Incorporation of Disinfectant Solutions on Setting Time, Linear Dimensional Stability, and Detail Reproduction in Dental Stone Casts

Purpose: The aim of this paper was to analyze the influence of incorporation of disinfectants during the cast die stone-setting time. Setting time, linear dimensional stability, and reproduction details on casts were measured.Materials and Methods: Die stone type IV specimens with disinfection solutions (sodium hypochlorite 1%, glutaraldehyde 2%, chlorhexidine 2%) were incorporated in two concentrations (50%, 100%). The detail reproduction, dimensional stability, and setting time were tested in accordance with ADA recommendations.Results: Disinfecting solutions promoted an increase in setting time compared to control; sodium hypochlorite was responsible for the highest setting time. The addition of undiluted sodium hypochlorite 1.0% led to contraction during setting, but the groups with 50% diluted sodium hypochlorite 1.0% and undiluted chlorhexidine 2.0% resulted in intermediate values compared to the other groups, thus matching the control. The others did not demonstrate any effect on expansion. For detail reproduction, it was observed that the control group presented results similar to the others, except those where sodium hypochlorite was added.Conclusions The addition of sodium hypochlorite in both dilutions significantly altered, negatively, all the evaluated properties. But the addition of glutaraldehyde and chlorhexidine did not promote any significant alterations in the evaluated properties.

pH, Calcium Ion Release, and Setting Time of an Experimental Mineral Trioxide Aggregate-based Root Canal Sealer

Introduction: An experimental mineral trioxide aggregate sealer (MTAS) has been developed for use as a root canal sealer. The aim of this study was to evaluate the setting time, pH, and calcium ion release of MTAS compared with white Portland cement (CPB-40; Votorantin Cimentos, Camargo Correa SA, Pedro Leopoldo, MG, Brazil), white MTA Angelus (MTA; Angelus, Londrina, PR, Brazil), and AH Plus (Dentsply DeTrey, Konstanz, Germany). Methods: For the evaluation of setting time, each material was analyzed using Gilmore-type needles. Polyethylene tubes with the materials were immersed in distilled water for the measurement of pH (digital pH meter) and calcium release (atomic absorption spectrophotometry). The evaluations were performed at 3, 6, 12, 24, and 48 hours and 7, 14, and 28 days. Data were analyzed by analysis of variance and the Tukey test at 5% significance level. Results: MTAS showed higher calcium release at all experimental periods, a greater increase in pH up to 48 hours and the longest setting time. Conclusions: MTAS presented favorable properties for its indication as a root canal sealer. (J Endod 2011;37:844-846)

Determination of the properties of an experimental glass polyalkenoate cement prepared from niobium silicate powder containing fluoride

Objectives. The purpose of this paper is to modify the conventional calcium fluoro-aluminosilicate glass, which is used in the formation of glass ionomer cements (CIGs) by the niobium addition and to study the properties of GICs obtained.Materials and methods. Sol-gel process was used to prepare the powder at lower temperature than fusion method. Glass-ceramic powder obtained in this way was used to prepare the GICs. The properties such as working and setting times, microhardness and diametral tensile strength were evaluated for the experimental GICs and a commercial luting cement.Results. The ideal powder:liquid (P:L) ratio determined to prepare the experimental GICs was equal to 1:1. The cements prepared using this ratio showed working and setting times similar to the commercial GICs. in mechanical tests it was observed that microhardness and diametral tensile strength of the experimental GICs decreased significantly with the reduction of P:L ratio. on the other hand, the results obtained in microhardness tests indicated that the presence of niobium was a positive factor.Significance. The chemical process allows the development of glass-ceramic powder at 600 degrees C which is the goal of the present paper. It was concluded that GICs containing niobium might be used in dental applications and these results encourage further researches on other compositions. (c) 2007 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

The Influence of Calcium Chloride on the Setting Time, Solubility, Disintegration, and pH of Mineral Trioxide Aggregate and White Portland Cement with a Radiopacifier

This study evaluated the influence of addition of 10% calcium chloride (CaCl(2)) on the setting time, solubility, disintegration, and pH of white MTA (WMTA) and white Portland cement (WPC). A test of the setting time was performed following the #57 ADA specifications and a test of the final setting time according to the ASTM. For the solubility tests disintegration and pH, Teflon rings were filled with the cements and weighed after setting. After 24 h in a desiccator, they were once again weighed. Thereafter, they were immersed in MiliQ water for 24 and 72 h and 7, 14, and 28 days, with maintenance in the desiccator and weighing between periods. The pH of water in which the rings were immersed was measured immediately after contact with them and in the other periods. The addition of CaCl(2) provided a significant reduction (50%) in the initial setting time of cements. The final setting time of WMTA was reduced in 35.5% and the final setting time of WPC in 68.5%. The WMTA with CaCl(2) absorbed water and gained weight with time, except for in the 24-h period. The addition of CaCl(2) to the WPC reduced its solubility. The addition of CaCl(2) increased the pH of WMTA in the immediate period and at 24 and 72 h and for WPC in the immediate period and at 24 h. The addition of CaCl(2) to WMTA and WPC reduced the setting times and solubility of both and increased the pH of cements in the initial periods. (J Endod 2009;35:550-554)

High-pressure granulites from Carire, Borborema Province, NE Brazil: Tectonic setting, metamorphic conditions and U-Pb, Lu-Hf and Sm-Nd geochronology

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Evaluation of a double-setting alpha-tricalcium phosphate cement in eviscerated rabbit eyes

Purpose: To evaluate the macroscopy, microstructure, and tissue reaction of a double-setting a-tricalcium phosphate bone cement used as an intraocular implant in rabbits.Methods: the internal and external surface of the double-setting a-tricalcium phosphate implant was analyzed macroscopically and by scanning electron microscopy. Twelve New Zealand rabbits received 12-mm implants made of double-setting alpha-tricalcium phosphate cement after unilateral evisceration. Clinical evaluation was performed daily for the first 15 days after surgery and at 15-day intervals until the end of the study period. For histopathologic analysis, 3 animals per experimental period were submitted to enucleation at 15, 45, 90, and 180 days.Results: on gross inspection, the external surface of the implant was solid, smooth, and compact. The microarchitecture was characterized by the formation of columns of hexagonal crystals with interconnecting channels forming micropores. No wound dehiscence, signs of infection, or implant extrusion were observed in any animal throughout the study period. Histologic examination revealed the formation of fibrovascular tissue surrounding the implants, and there were signs of minimal integration of the surface limiting the fibrocellular cap with the space previously occupied by the implant.Conclusions: the double-setting alpha-tricalcium phosphate implant behaved as an inert and nonintegratable material. The lack of incorporation of this material by fibrovascular tissue is related to its characteristics of compactness and high resistance.

Evaluation of the thermal shrinkage of titanium and the setting and thermal expansion of phosphate-boded investments

Statement of problem. There are few studies on titanium casting shrinkage, and phosphate-bonded investments for titanium casting have not produced appropriate marginal fit.Purpose. The purpose of this study was to determine the thermal shrinkage of titanium and the setting and thermal expansion of 3 phosphate-bonded investments.Material and methods. The thermal shrinkage between the melting temperature and room temperature was calculated using a titanium thermal expansion coefficient. The thermal and setting expansion were measured for 3 phosphate bonded investments: Rematitan Plus (RP) specific for titanium, Rema Exakt (RE), and Castorit Super C (CA), using different special liquid concentrations (100%, 75%, and 50%). Setting expansion was measured for cylindrical specimens 50 mm long x 8 mm in diameter with a transducer. The heating and cooling curves were obtained with a dilatometer (DIL 402 PC). The total expansion curve was drawn using software, and temperatures to obtain expansion equivalent to titanium casting shrinkage were determined (n=5). In addition, the total expansion of the control group (RP at 430 degrees C) was measured, as well as the temperatures at which the other groups achieved equivalent total expansion (n=5). Data were analyzed by 1-way ANOVA and the Tukey HSD test (alpha=.05).Results. Titanium casting shrinkage was estimated as 1.55%. RP did not achieve this expansion. RE achieved expansion of 1.55% only with a special liquid concentration of 100% at 594 degrees C. CA with all special liquid concentrations attained this expansion (351 degrees C to 572 degrees C). Total expansion of the control group was 0.86%, and the other groups reached that expansion within the range of 70 degrees C to 360 degrees C.Conclusions. Only RE and CA demonstrated sufficient expansion to compensate for titanium casting shrinkage. All groups reached total expansion equivalent to that of the control group at significantly lower temperatures.

Utilization of peritoneal dialysis in the acute setting

Peritoneal dialysis (PD), although classically described and utilized in the treatment of patients with end-stage renal disease, can also be utilized in the acute setting in different clinical situations. Recent studies showed that, in patients with acute renal failure, it is possible to obtain reasonable dialysis doses with adequate metabolic and etectrolytic control and tow incidence of complications by utilizing continuous PD through a cycler at high volume. In patients with congestive heart failure without end-stage renal disease, PD is capable of promoting clinical improvement with slow removal of liquids, becoming an attractive alternative for situations of rapidly or slowly worsening cardiac function. In patients submitted to chronic hemodialysis but who have vascular access difficulties, PD can also be utilized as a bridge, thereby avoiding the use of central venous catheters, which can be associated with infectious complications such as bacterial endocarditis. New studies must be realized showing other indications for PD.

Emplacement setting of the granite sheeted pluton of Esperanca (Brasiliano orogen, Northeastern Brazil)

Anisotropy of magnetic susceptibility (AMS) and isotopic (U-Pb, Sm-Nd) data were combined to study the emplacement setting of the granite sheets that constitute the Esperanca pluton in the Borborema Province (Northeastern Brazil). The sheets dip moderately to the SE along the contact zone between the Paleoproterozoic basement rocks and Early Neoproterozoic orthogneisses and metasediments. Granite fabrics were determined mainly using AMS in 136 sites distributed within the central and western part of the pluton. The sheets normally have susceptibility lower than 0.35 mSI but, locally, where a Ti-poor magnetite appears with titanite, the susceptibility increases up to 5 mSI. Comparison between the silicate fabric and AMS showed inconsistencies between the shape of mineral and magnetic ellipsoids despite of their orientations that fit fairly well to each other. AMS indicated the deformation was partitioned between the lower (tonalite, syenogranite) and upper (leucogranite and coarse porphyritic granite) sheets. In the lower sheets the curvilinear lineation trajectory is attributed to a dominant heterogeneous pure shear event that flattened laterally the still molten tonalite and syenogranite into the regional foliation. ne associated microstructures are typically magmatic. Zircon U/Pb data of the syenogranite yielded a crystallization age of 592 +/- 5 Ma. In the upper sheets the fabric recorded a component of simple shear deformation that displaced the coarse porphyritic granite and the top gneissic host rocks to the southwest. Microstructures are mostly of post-full crystallization type. T(DM) model ages and epsilon(Nd) (t = 0) values indicate that the magma contaminated by partial melting of the regional host rocks. Sheet propagation at the emplacement level would have exploited the contact zone between crustal blocks of different rheologies when the melt pressures would be able to tensionally fail the anisotropy of the host rocks. (C) 2004 Elsevier B.V. All rights reserved.

The workload and plasma ion concentration in a training match session of high-goal (elite) polo ponies

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tectonic setting and U/Pb zircon dating of the plutonic Socorro Complex in the Transpressive Rio Paraíba do Sul Shear Belt, SE Brazil

The Precambrian Rio Paraíba do Sul Shear Belt comprises a 200-km-wide anastomosing network of NE-SW trending ductile shear zones extending over 1000 km of the southeastern coast of Brazil. Granulitic, gneissic-migmatitic, and granitoid terrains as well as low- to medium-grade metavolcanosedimentary sequences are included within it. These rocks were affected by strong contractional, tangential tectonics, due to west-northwestward oblique convergence of continental blocks. Subsequent transpressional tectonics accomodated large dextral, orogen-parallel movements and shortening. The plutonic Socorro Complex is one of many deformed granites with a foliation subparallel to that of the shear belt and exposes crosscutting relationships between its tectonic, magmatic, and metamorphic structures. These relationships point to a continuous magmatic evolution related to regional thrusts and strike slip, ductile shear zones. The tectonic and magmatic structural features of the Serra do Lopo Granite provide a model of emplacement by sheeting along shear zones during coeval strike-slip and cross shortening of country rocks. Geochronological data indicate that the main igneous activity of Socorro Complex spanned at least 55 million years, from the late stage of the northwestward ductile thrusting (650 Ma), through right-lateral strike slip (595 Ma) deformation. The country rocks yield discordant age data, which reflect a strong imprint of the Transamazonian tectono-metamorphic event (1.9 to 2.0 Ma). We propose a model for the origin of calcalkaline granites of the Ribeira Belt by partial melting of the lower crust with small contributions of the lithospheric mantle during transpressional thickening of plate margins, which were bounded by deep shear zones. The transpressional regime also seems to have focused granite migration from deeper into higher crustal levels along these shear zones.

Genetic control of fruit-setting percentage of tomatoes tolerant to high temperatures

The aim of present work was to study, through means and variances of generations, the genetic control of fruit-set percentage in tomatoes, in a biparental cross between line Jab-95 (resistant to fruit-set) and 'Caribe' cultivar (susceptible to fruit-set) after being subjected to high temperatures. F1, F2, and backcross generations for both parents (P 1, P2) were produced in a greenhouse at FCAVUNESP, Jaboticabal-SP, Brazil. A randomized complete block experimental design with four replications was used to evaluate the different generations. Estimates of genetic parameters were obtained according to Mather and Jinks (1982). An additive-dominant model was fitted to explain the variation observed. The mean degree of dominance (0.54), indicated incomplete dominance in the direction of increasing fruit-set percentage at high temperatures. The genetic control of fruit-set percentage, at high temperatures, for tomato was found to be oligogenic or polygenic (3.54 genes). The heritability in a limited sense was 83.91%, suggesting that the selection of individuals based on the characteristic evaluated can be efficient.

Liposomal daunorubicin and dexamethasone as a treatment for multiple myeloma - The DD protocol

Context and Objective: Lipasomial daunorubicin has been used to treat hematological malignancies, including multiple myelomo (MM). The goal was to evaluate efficacy, side-effects and toxicity of liposomal daunorubicin and dexamethasone (DD Protocol). Design and Setting: Prospective study of Sírio-Libonês, São Camilo, Brasil and Alemão Oswaldo Cruz hospitals. Methods: Twenty consecutive patients with active MM received four cycles of liposomal daunorubicin intravenously for two hours (25-30 mg/m 2/day) on three consecutive days per month, with oral dexamethasone, (10 mg every six hours) on four consecutive days three times a month. Results: The male/female ratio was 1:1 and median age 60. Nine patients were stage IIA, ten IIIA and one IIIB. The median from diagnosis to starting DD was 13 months. All patients received four cycles, except one. Fifteen had already received chemotherapy before DD. Responses of > 50% reduction in serum monoclonal paraprotein were observed in six patients after first cycle (30%), six after second (30%) and four after third (20%), while four (20%) did not obtain this. Initially, 17 patients (85%) had anemia: 12 (70%) achieved correction. Progressive disease was observed in three patients (15%), while one had minimal response, four (20%) partial and 12 (60%) complete. Hemotologlical toxicity was acceptable: three patients (15%) had neutrophils < 1,000/mm 3; none had thrombocyfopenia. Gastrointestinal toxicity was mild: nausea (10%), anorexio (15%) and no vomiting. Conclusions: This treatment has mild toxicity and good response rate. It may therefore be feasible before autologous bone marraw transplantation.

Setting the preheating process of electronic ballasts for hot-cathode fluorescent lamps, considering the Rh/Rc ratio

This paper presents a new model for the representation of the electrodes filaments of fluorescent lamps, during their preheating, and an analysis capable to guide the design of the preheating process in electronic ballasts. The main improvement obtained with the lamp model is the accurate theoretical reproduction of the behavior of the Rh/Rc ratio during the preheating process. In addition, using the proposed methodology based on the lamp model, it is possible to set a proper preheating process to the electrodes filaments, without the necessity of exhaustive empirical adjustments in the prototype, reducing time and costs involved in the design of ballasts with preheating capabilities. © 2006 IEEE.

Composition of stingless bee honey: Setting quality standards

Compositional data from 152 stingless bee (Meliponini) honey samples were compiled from studies since 1964, and evaluated to propose a quality standard for this product. Since stingless bee honey has a different composition than Apis mellifera honey, some physicochemical parameters are presented according to stingless bee species. The entomological origin of the honey was known for 17 species of Meliponini from Brazil, one from Costa Rica, six from Mexico, 27 from Panama, one from Surinam, two from Trinidad & Tobago, and seven from Venezuela, most from the genus Melipona. The results varied as follows: moisture (19.9-41.9g/100g), pH (3.15-4.66), free acidity (5.9-109.0meq/Kg), ash (0.01-1.18g/100g), diastase activity (0.9-23.0DN), electrical conductivity (0.49-8.77mS/cm), HMF (0.4-78.4mg/Kg), invertase activity (19.8-90.1IU), nitrogen (14.34-144.00mg/100g), reducing sugars (58.0-75.7g/100g) and sucrose (1.1-4.8g/100g). Moisture content of stingless bee honey is generally higher than the 20% maximum established for A. mellifera honey. Guidelines for further contributions would help make the physicochemical database of meliponine honey more objective, in order to use such data to set quality standards. Pollen analysis should be directed towards the recognition of unifloral honeys produced by stingless bees, in order to obtain standard products from botanical species. A honey quality control campaign directed to both stingless beekeepers and stingless bee honey hunters is needed, as is harmonization of analytical methods. © 2007 Asociación Interciencia.