Lower intercanine width and gingival margin changes. A retrospective study.

OBJECTIVE: To determine if changes in the lower intercanine widths during orthodontic treatment with fixed appliances result in gingival margin changes around the lower canines and incisors. METHOD: Pre- and post-treatment intra-oral photographs and orthodontic study models of 178 Caucasian adolescents (101 female, 77 male) were used. All subjects were treated with fixed appliances. The subjects had mean ages of 11.41 (SD: 1.83) years and 14.91 (SD: 1.78) years on their initial and final records respectively. The latter were taken 28 days or more after the appliances had been removed. The inclusion criteria were: Angle Class I or Class II malocclusion (with or without transverse and/or vertical discrepancies); nonextraction treatment; less than 4 mm crowding or spacing; fully erupted lower incisors and good periodontal health. The intercanine widths and the positions of the gingival margins relative to the maximum curvatures of the labial surfaces of the lower canines and incisors were measured with digital calipers. RESULTS: A significant association was found between unaltered intercanine widths and coronal migration of the gingival margins (p = 0.045). There were no significant associations between either increased or reduced intercanine widths and changes in the gingival margins. CONCLUSIONS: Following orthodontic treatment coronal migration of the gingival margins around the lower incisors and canines is more likely to be associated with an unaltered intercanine width.

Efeito do desbaste seletivo nas estimativas de parâmetros genéticos em progénies de Pinus caribaea Morelet var. hondurensis

The objective of this work was to study the effect of selective thinning on the estimates of genetic parameters in progenies of Pinus caribaea var. hondurensis. The progeny test was installed in June 1986, following a 10 × 10, triple square lattice design, containing ten trees in linear plots in 3.0 × 3.0m spacing. Twelve years after the planting, a selective thinning based on Multi-effect index (selection for DBH) was performed, leaving six trees per plot. The assessments were done in four situations: A (before thinning); B (among thinned trees); C (among remnant trees at 13 years of age) and D (two years after the thinning). The following traits were analyzed: total height (H), diameter at breast height (DBH), volume (VOL), stem form (FOR), foxtail (FT), wood density at 1.3 m (WD1) and wood density at the half height (WD2). The thinning led to increase in the estimates of variability among progenies for VOL and decrease for ALT and DBH. There was a high and positive genetic correlation among the growth traits, mainly between DBH and VOL. The latter remained unchanged after thinning. The narrow-sense heritabilities at the individual level, showed a slight increase while at the family mean level had a reduction with the thinning. The estimates of breeding values increased with the thinning. This may lead to an easier identification of the best progenies in further selection.

Arranjo espacial de plantas de milho em sistema plantio direto

The interaction of management practices that increases plant density and reduces row spacing by spatial arrangement, if well planned, can be an excellent opportunity for the producers to increase their profitability. The objective of this study was to evaluate the variation effects of plant spatial distribution in two maize hybrids cultivated in a no-tillage system on the production components. The study was conducted in the CECA/UFAL. The treatments consisted of the cultivation of two hybrids of maize, FORT and AGN 30A00, in row spacings of 0.80 and 0.40 m and with plant densities of 60,000 and 70,000 plants ha -1. The statistical design was randomized blocks in a 2 x 2 x 2 factorial scheme, with three replications. From the results obtained, it may be concluded that neither the row spacing reduction nor plant density increase, as isolated practices, do not increase grain yield in the tested cultivars. The association of the reduction in row spacing and increase in plant population resulted in significant gain in grain productivity for the hybrid FORT.

Occurrence, extension, and severity of gingival margin alterations after orthodontic treatment.

To assess the occurrence, extension, and severity of gingival margin alterations in a sample of youth after orthodontic treatment. Records from 209 Caucasian adolescents (118 female and 91 male) before and after orthodontic treatment were selected. Patients presented a mean age at the beginning of orthodontic treatment of 11.20 ± 1.86 years and a final mean age of 14.72 ± 1.83 years. Class I and II patients with mandibular incisors and canines that were completely erupted and with spacing or crowding not exceeding 4 mm were evaluated. The presence of gingival recession on the labial surface of the mandibular anterior teeth was evaluated in intraoral photographs and casts made before and after treatment. The proportion of patients with gingival recession after treatment was statistically higher than at the beginning (P<.001). After orthodontic treatment, gingival recession was not present in any of the teeth for 63.6% of the patients; in 29.2% of the patients, recession was present in at least 1 tooth. In terms of severity, the majority of affected teeth (47%) presented gingival recession less than 2 mm and in 2% more than 4 mm. It may be concluded that alterations in the gingival margin, especially gingival recession, occur in patients after orthodontic therapy, but the extent and severity of this finding are low. COPYRIGHT © 2007 BY QUINTESSENCE PUBLISHING CO, INC.

Osteologia craniana de Nyctibiidae (Aves, Caprimulgiformes)

The Potoos form an exclusively neotropical family of nocturnal birds distributed throughout Central and South America, except Chile, and reaching their highest diversity in the Amazon region. The seven currently recognized species are certainly among the most poorly known birds of this region. They are characterized by a distinctive mimicry of vegetal trunks, where they remain almost motionless during daytime. For this reason, their nocturnal and cryptic habits make them exceedingly difficult to study. Published accounts on behavior and natural history of the family are scarce and contributions regarding its anatomy are rare. Here we sample six of the seven currently recognized species of Nyctibiidae, including Nyctibius grandis, N. aethereus, N. griseus, N. jamaicensis, N. leucopterus and N. bracteatus, in order to conduct a detailed and illustrated description of the skull and jaw osteology. High interspecific variation in skull osteology was observed in the family. Species of this family possess a highly modified skull, adapted to their life habits, which shelters their well developed eyes and permits a large mouth opening. The bones that form the palate structure exhibit a dorsoventral flattening, particularly in the pterigoid and parasphenoid bones, with the palatine bone being a broadly developed, wing-shaped structure. In the maxilar region, near the jugal arch, there is a tooth-like projection, unique among birds, which may assist in the retention of prey upon capture. The vomer bone is highly variable within the family, showing varying numbers of rostral projections amongst species. The broad occipital region exhibits large spacing between the quadrate bones, which are vertically disposed and possess a reduced processus orbitalis. The mandible, which is flexible and elastic, has an extremely short symphyseal region and sindesmotic joints in both mandibular rami. As a family, potoos possess a highly specialized skull which provides insight into the relationship between the form of the structures and the feeding habits of the species. Furthermore, the large interspecific variation in skull morphology emphasizes the needs for taxonomic revision within the family, which at present is lumped into a single genus.

Ultrasonic material characterization using diffraction-free PVDF receivers

This work describes the use of a large aperture PVDF receiver in the measurement of density of liquids and elastic constants of composite materials. The density measurement of several liquids is obtained with the accuracy of less than 0.2% using a conventional NDT emitter transducer and a 70-mm diameter, 52-μm P(VDF-TrFE) membrane with gold electrodes. The determination of the elastic constants of composite materials is based in the measurement of phase velocity. It is shown that the diffraction can lead to errors around 1% in the velocity measurement when using a pair of ultrasonic transducers (1MHz and 19mm diameter) operating in transmission-reception mode separated by a distance of 100 mm. This effect is negligible when using a pair of 10-MHz transducers. On the other hand, the dispersion at 10 MHz can result in errors of about 0.5%, measuring the velocity in composite materials. The use of an 80-mm diameter, 52-μm thick PVDF membrane receiver allows measuring the phase velocity without the diffraction effects.

Climate Change and Development in Latin America and the Caribbean. Overview 2009

Includes bibliography

Desempenho de semeadora-adubadora em função do prepa ro de solo e espa çamento da cultura do milho

The performance of machines and agricultural implements are of fundamental importance, especially when subjected to different types of soil tillage, and have to adapt to these conditions, in order to promote good operational performance. The objective of this study was to analyze the operational performance of a Marchesan Supreme Cop grain drill, equipped with four rows, spaced 0.90 m, according to three types of tillage: conventional tillage (plowing and two harrowing series), reduced tillage (scarification with a roller), and no-tillage, in areas previously seeded with maize (Zea mays L.), at two spacing measures (0.90 m and 0.45 m). The results indicate that the demand for power, tensile stress, and motor rotation, in the sowing operation, were not influenced by tillage and maize crop. The tractor wheel slip showed different results, being lower in no-tillage and higher in conventional and reduced tillage.

Enclaves fortificados e segregação urbana: o caso de Jundiaí

The article discusses the spread of closed condominiums in Jundiaí (SP). The studies about this phenomenon have predominantly focused on metropolitan areas; therefore, the relevance of research on medium-sized cities in order to identify similarities and differences among different urban scales. The main objective was to investigate the spacing phenomenon of closed condominiums as a housing pattern tendency as well as its social, urban and environmental impact. This study encloses the period from 1970 to the present.

Emissions from sugar cane fires in the Central & Western State of São Paulo and aerosol layers over metropolitan São Paulo observed by IPEN's lidar: Is there a connection?

The central and western parts of the State of São Paulo are well-known for vast sugar cane plantations, which during the harvest time are traditionally burnt about 12 hours before manual cutting. This procedure causes the release of large quantities of aerosols and a variety of gases, which can be observed by IPMet's radars, located in Bauru and Presidente Prudente, on days with no or little rain. Depending on the distance of these plumes from the radar, they can be detected up to 5 km amsl or more, and are subsequently being transported by winds to other regions. During the dry winter season of 2008, such plumes, attributed to cane fires, were frequently observed by IPMet's radars and documented in terms of radar reflectivity, time and location during the period 10 th - 21 st July 2008. At the same time, IPEN's Elastic Backscatter Lidar in São Paulo observed layers of aerosols of variable strength and heights above the city. The most significant days, viz. 14 and 15 July 2008 had been selected for calculating backward, as well as forward trajectories, deploying the European Flextra 3.3 Trajectory Model, which was initiated with ECMWF historic data with a 0,25 o×0,25 o grid spacing. The results presented here show an excellent match between the radar-detected sources of the plumes on 11 th July 2008 in the central parts of the State and the observations by IPEN's Lidar over Metropolitan São Paulo on 14 th July 2008, both in terms of forward and backward trajectories, as well as their heights, with a transport duration of approximately 70 hours under the prevailing meteorological conditions. © Sociedad Española de Óptica.

Desenvolvimento inicial de variedades e clones de cana-de- açúcar em Latossolo Vermelho Distrófico, Aparecida do Taboado-MS

In Brazil, as in other sugar cane (Saccharum spp.) producing countries, varieties and clones have been continuously developed and tested in order to obtain varieties better adapted to changes in climate, soils and management, seeking a better performance in soils and climates of low agricultural suitability for the culture. In this study, the initial vegetative growth and performance of five sugar cane clones (CT96-3095, CT95-3079, CT95-1425, CT96-3024, CT92-1882) and two varieties (SP81-3250 and SP91-1049) were evaluated in an environment characterized by soils of low fertility and sandy texture. The experiment was carried out in a randomized design with seven treatments, consisting of the two sugar cane varieties and five clones. The plots contained six 15 meters sugar cane rows with a line spacing of 1.50 m. The average tiller number, tiller leaf area, vegetative cover, shoot biomass and rate of cover between rows of sugarcane were determined through six assessments in the first half of 2008. At the end of the evaluation (116 days after planting) the results showed that the clones (CT96-3095, CT95-3079, CT95-1425, CT96-3024, CT92-1882) were not significantly superior to the two considered varieties (SP81-3250 and SP91-1049).

Avaliação da uniformidade de aplicação de água em gotejadores em função do teor de ferro

Este trabalho teve por objetivo estudar a variação de vazão em tubogotejadores NaanPC laranja e NaanPC azul em função de precipitados químicos, ao longo do tempo de funcionamento, quando submetidos a uma água rica em ferro, avaliando-se especificamente o coeficiente de uniformidade de Christiansen (CUC) e o coeficiente de uniformidade de distribuição (CUD). O experimento foi desenvolvido em uma bancada de ensaios para tubogotejadores no Laboratório de Ensaio de Equipamentos para Irrigação do Departamento de Engenharia Rural da Faculdade de Ciências Agronômicas - UNESP, localizado no município de Botucatu – SP. O experimento foi montado em esquema fatorial 2x2x7, sendo duas doses de Fe, dois modelos de gotejadores e sete tempos de funcionamento, com três repetições, totalizando 84 parcelas experimentais. Efetuou-se a análise de variância pelo teste F. As médias das vazões dos gotejadores foram comparadas pelo teste de T de Student a 5% de probabilidade. Os resultados obtidos não apontaram diferença significativa nas diferentes doses de ferro. Entretanto, os resultados apontaram diferença significativa na interação gotejador x tempo e coeficiente de uniformidade de Christiansen (CUC).

Luminescent multifunctional biocellulose membranes

Luminescent biocellulose membranes were obtained by incorporation of ethanolic solutions of the europium compounds [Eu(BTFAC)3(H2O)2], [Eu(BTFA) 3(DBSO)2], [Eu(BTFA)3(PTSO)2] and [Eu(BTFA)3(FSO)2] (BTFAC- 4,4,4-Trifluoro-1- phenyl-1,3-butanedione DBSO- dibenzyl sulfoxide, PTSO- p-Tolyl sulfoxide and FSO- phenyl sulfoxide). Selfsustainable semi-transparent composite membranes were obtained showing strong emission under UV exctiation. The antenna hole played by the ligands was observed to be more efficient in the composite membranes than in the precursor complexes which by themselves are also strong red emitter compounds. These new multifuctional membranes could find application in different areas as phosphors and UV→Visible energy converting devices. © 2011 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

Perda de carga em mangueiras gotejadoras novas e usadas

This paper aims to determine the importance of emitter ́s local head loss in the hydraulic design of hose drip lines, as well as comparing the result of equations that calculate the local head loss; besides verifying the influence of iron precipitated at the hose head loss made in Brazil. The result found that localized head loss represents 23% of the total head loss; the equations showed significant results and the total head loss increased in an average of 20% after the irrigation system was used with water rich in iron.

Estimativas de parâmetros genéticos para caracteres quantitativos em progênies de polinização aberta de Eucalyptus urophylla

Eucalyptus urophylla S. T. Blake is outstanding for valuable wood production potential, adaptation plasticity for different environmental conditions, and for tolerance to canker. However, genetic improvement of this specie in Brazil depends on the existence of genetic variability in the introduced populations. The objective of this study was to investigate the genetic variation and gains in quantitative traits in a population established in 1992 in Selvíria - MS. The progeny trial was established in a partially balanced, 8 x 8 lattice design, with 64 families, collected at Anhembi Experimental Station (IPEF/ESALQ/USP). Each plot was made up of eight trees planted in a 3 × 3 m spacing. Significant among families genetic variations were observed in diameter at breast height (DBH), bark type, stem form, and survival. Estimates of average family heritability were high for all traits, ranging from 0.50 to 0.85. The simulated selection by using multi-effect index showed that under a varying number of plants per family. This method is the most indicated to maximize genetic gains (7.24%) and the effective population size (69.3). These results are a useful support for the transformation of this test into a seedling seed orchard and to become a source of vegetative material to build a clonal seed orchard.