Effect of cryoprotectants on the reconstitution of silica nanoparticles produced by sol-gel technology

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of beta-cyclodextrin on the properties of norfloxacin form A

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Use of high-resolution thermogravimetric analysis (HRTG) technique in spent FCC catalyst/Portland cement pastes

Thermogravimetric analysis is one of the most common instrumental techniques used for the characterization of pastes, mortars and concretes based on both calcium hydroxide and Portland cement. Important information about pozzolanic materials can be assessed concerning calcium hydroxide consumption and the formation of new hydrated products. Nevertheless, in some cases, problems associated with the overlapped decomposition processes for hydrates make the analysis of obtained data difficult. In this paper, the use of high-resolution thermogravimetric analysis, a powerful technique that allows separating decomposition processes in analysis of hydrated binders, was performed for spent FCC catalyst-Portland cement pastes. These pastes were monitored for 1, 4, 8 h and 1, 2, 3, 7 and 28 curing days. In order to study the influence of the pozzolanic material (spent FCC catalyst), Portland cement replacements of 5, 15 and 30 % by mass were carried out. The presence of spent FCC catalyst in blended pastes modified the amount and the nature of the formed hydrates, mainly ettringite and stratlingite.

Study of ceramic block manufacture with the addition of waste from iron ore extraction

This work is intended to study the possibility of adding an amount of waste from iron mining in the ceramic mass. Clay and coal, from Vale do Paraiba, Sao Paulo, Brazil, were used in this research. These raw materials are used in the ceramic block manufacture. Clay and waste were analyzed by X-ray fluorescence and X-ray diffraction, particle size, differential thermal and thermogravimetric analysis. Liquid limit and plasticity index tests were performed in order to determine the amount of waste that which should be used in the ceramic mass. After determining the amount of waste, all samples were uniaxially pressed and sintered at 900 degrees C. Surface roughness measurements, apparent porosity and bulk density technique and three-point flexural tests were also performed to characterize the samples. The results showed that by adding the exact amount of waste, which was determined by the essays, it is possible to manufacture solid bricks.

Thermal and spectroscopic study of the 3,4-(methylenedioxy) cinnamate compounds of transition metals in the solid state

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermal degradation of both latex and latex cast films forming membranes: combined TG/FTIR investigation

Latex collected from natural rubber trees forming membranes can be used as biomaterials in several fields being the temperature a key parameter. Thermogravimetry (TG) coupled to Fourier transform infrared spectroscopy (FTIR) is a useful technique to investigate the thermal degradation of both latex and cast films (membranes), wich were obtained from Hevea brasiliensis (RRIM 600 clone) and used without stabilization. The membranes were prepared by casting the latex onto a glass substrate at 65 degrees C for 6 h. The thermal degradation was followed by FTIR spectra acquisition along the process, allowing the identification of the gaseous components evolved upon the thermal treatment. According to TG measurements, the main processes of thermal degradation of the latex and membranes occur at three temperature intervals for both.

Synthesis, characterization and thermal behavior of heterobimetallic carbonyl compounds of the type [W(CO)(4)(bipy)(CuX)] (X=Cl, N-3, ClO4 and BF4)

Four new heterobimetallic metal carbonyls were synthesized by the reaction of [W(CO)4(bipy)] (1) with copper(I) compounds leading to species with the general formula [W(CO)4(bipy)(CuX)] (X = Cl, N3, ClO4, BF4) (2-5). The metal carbonyl compounds were characterized by elemental analysis, infrared and UV -visible electronic spectroscopy and thermogravimetric analysis. The IR data for 2-5 show carbonyl stretching band patterns similar to compound 1 ; ie they exhibit the same number of bands. The UV - vis results show a dissociation reaction generating the starting compound 1 and CuX as consequence of a weak interaction between 1 and CuX. Thermal decomposition mechanisms as well as the thermal stability are influenced by the CuX fragments. The thermal stability decreases in the order [W(CO)4(bipy)] > [W(CO)4(bipy)(CuCl)] > [W(CO)4(bipy) (CuBF4)]. The X-ray results show the formation of WO3, CuWO4, Cu2O and CuO as final decomposition products.

Synthesis, characterization and thermal behavior of cyclopalladated compounds of the type [Pd{C6H4CH2N(CH3)(2)}(mu-X)](2) (X= Cl, NCO, SCN, CN)

The dimeric compound [Pd(dmba)(μ-Cl)]2 (1) (dmba = N,N-dimethylbenzylamine) reacts with KX, in methanol/acetone, affording the analogous dimeric pseudohalide-bridged species [Pd(dmba)(X)]2 [X = NCO(2), SCN(3), CN(4)]. The compounds were characterized by elemental analysis, infrared spectroscopy, NMR and thermogravimetric analysis. The IR data for 2-4 showed bands typical of coordinated pseudohalide ligands indicating clearly the occurrence of the exchange reaction. Their thermal behavior was investigated and suggested that their thermal stability is influenced by the bridging ligand. The thermal stability decreased in the order [Pd(dmba)(μ-SCN)]2>[Pd(dmba)(μ-Cl)] 2>[Pd(dmba)(;u-NCO)]2>[Pd(dmba)(μ-CN)]2. The X-ray results showed the formation of PdO as final decomposition product. © 1999 Elsevier Science Ltd. All rights reserved.

Síntese, caracterização e avaliação da atividade biológica de metalofármacos de sulindaco com íons lantanídeos (III) no estado sólido

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Síntese, caracterização e estudo termoanalítico dos nicotinatos de lantanídeos (III) e de ítrio (III), no estado sólido

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Red Mud from Brazil: Thermal Behavior and Physical Properties

The main constituents of red mud produced in Aluminio city (S.P., Brazil) are iron, aluminum, and silicon oxides. It has been determined that the average particle diameter for this red mud is between 0.05 and 0.002 mm. It is observed that a decrease in the percentage of smaller particles occurs at temperatures greater than 400 degrees C. This observation corresponds with the thermal analysis and X-ray diffraction (XRD) data, which illustrate the phase transition of goethite to hematite. A 10% mass loss is observed in the thermal analysis patterns due to the hydroxide-oxide phase transitions of iron (primary phase transition) and aluminum (to a lesser extent). The disappearance and appearance of the different phases of iron and aluminum confirms the decomposition reactions proposed by the thermal analysis data. This Brazilian red mud has been classified as mesoporous at all temperatures except between 400 and 500 degrees C where the classification changes to micro/mesoporous.

Formation of oxysulfide LnO(2)S(2) and oxysulfate LnO(2)SO(4) phases in the thermal decomposition process of lanthanide sulfonates (Ln = La, Sm)

This study investigates two lanthanide compounds (La(3+) and Sm(3+)) obtained in water/ethyl alcohol solutions employing the anionic surfactant diphenyl-4-amine sulfonate (DAS) as ligand. Both sulfonates were characterized through IR, TG/DTG (O(2) and N(2)). The thermal treatment of both compounds at 1273 K under air leaves residues containing variable percentages of lanthanide oxysulfide/oxysulfate phases shown by synchrotron high-resolution XRD pattern including the Rietveld analysis. The phase distributions found in the residues evidence the differences in the relative stability of the precursors.

Natural Membranes for Application in Biomedical Devices

Polymers from natural sources are particularly useful as biomaterials for medical devices applications. In this study, the results of characterization of a gelatin network electrolyte doped with europium triflate (Eu(CF3SO3)(3)) are described. The unusual electronic properties of the trivalent lanthanide ions make them well suited as luminescent reporter groups, with many applications in biotechnology. Samples of solvent-free electrolytes were prepared with a range of guest salt concentration. Materials based on Eu(CF3SO3)(3) were obtained as mechanically robust, flexible, transparent, and completely amorphous films. Samples were characterized by thermal analysis (thermo-gravimetry analysis (TGA) and differential scanning calorimetry (DSC), electrochemical stability, scanning electronmicroscopy (SEM), and photoluminescence spectroscopy.

Engineering Active Pharmaceutical Ingredients by Spray Drying: Effects on Physical Properties and In Vitro Dissolution

Active pharmaceutical ingredients have very strict quality requirements; minor changes in the physical and chemical properties of pharmaceuticals can adversely affect the dissolution rate and therefore the bioavailability of a given drug. Accordingly, the aim of the present study was to investigate the effect of spray drying on the physical and in vitro dissolution properties of four different active pharmaceutical ingredients, namely carbamazepine, indomethacin, piroxicam, and nifedipine. Each drug was dispersed in a solution of ethanol and water (70:30) and subjected to single-step spray drying using similar operational conditions. A complete characterization of the spray-dried drugs was performed via differential scanning calorimetry (DSC), scanning electron microscopy (SEM), X-ray powder diffraction (XRPD), particle size distribution analysis, solubility analysis, and an in vitro dissolution study. The results from the thermal analysis and X-ray diffraction showed that, except for carbamazepine, no chemical modifications occurred as a result of spray drying. Moreover, the particle size distribution of all the spray-dried drugs significantly decreased. In addition, SEM images showed that most of the particles had an irregular shape. There was no significant improvement in the solubility of the spray-dried drugs compared with the unprocessed compounds; however, in general, the dissolution rates of the spray-dried drugs showed a remarkable improvement over their non-spray-dried counterparts. Therefore, the results from this study demonstrate that a single spray-drying step may lead to changes in the physical properties and dissolution characteristics of drugs and thus improve their therapeutic action.

Effect of sorbitan-based surfactants on glass transition temperature of cellulose esters

Thermal behavior of mixtures composed of cellulose acetate butyrate (CAB), carboxymethylcellulose acetate butyrate (CMCAB), or cellulose acetate phthalate (CAPh), and sorbitan-based surfactants was investigated as a function of mixture composition by means of differential scanning calorimetry (DSC). Surfactants with three different alkyl chain lengths, namely, polyoxyethylenesorbitan monolaurate (Tween 20), polyoxyethylenesorbitan monopalmitate (Tween 40), and polyoxyethylene sorbitan monostearate (Tween 60) were chosen. DSC measurements revealed that Tween 20, 40, and 60 act as plasticizers for CAB, CMCAB, and CAPh (except for Tween 60), leading to a dramatic reduction of glass transition temperature (T-g). The dependence of experimental T-g values on the mixture composition was compared with theoretical predictions using the Fox equation. Plasticization was strongly dependent on mixture composition, surfactant hydrophobic chain length, and type of cellulose ester functional group.