Effectiveness-ntu computation with a mathematical model for cross-flow heat exchangers

Due to the wide range of design possibilities, simple manufactured, low maintenance and low cost, cross-flow heat exchangers are extensively used in the petroleum, petrochemical, air conditioning, food storage, and others industries. In this paper a mathematical model for cross-flow heat exchangers with complex flow arrangements for determining epsilon -NTU relations is presented. The model is based on the tube element approach, according to which the heat exchanger outlet temperatures are obtained by discretizing the coil along the tube fluid path. In each cross section of the element, tube-side fluid temperature is assumed to be constant because the heat capacity rate ratio C*=Cmin/Cmax tends toward zero in the element. Thus temperature is controlled by effectiveness of a local element corresponding to an evaporator or a condenser-type element. The model is validated through comparison with theoretical algebraic relations for single-pass cross-flow arrangements with one or more rows. Very small relative errors are obtained showing the accuracy of the present model. epsilon -NTU curves for several complex circuit arrangements are presented. The model developed represents a useful research tool for theoretical and experimental studies on heat exchangers performance.

Comparative studies of the anti-leishmanial activity of three Crotalus durissus ssp venoms

In this study, we compared the anti-leishmanial activity of three crotalic venoms (Crotalus durissus terrificus-Cdt, Crotalus durissus cascavella-Cdca, and Crotalus durissus collilineatus-Cdcol). Different concentrations of each venom incubated with Leishmania (Leishmania) amazonensis promastigotes were used. Cdt venom exhibited a higher anti-leishmanial activity (Inhibitory concentration-IC50-value of 4.70 +/- 1.72 mu g/ml) in comparison with that of Cdca venom (IC50 value of 9.41 +/- 1.21 mu g/ml), while Cdcol venom increased parasite numbers in 50% at a concentration of 44.30 +/- 2.18 mu g/ml. In addition, this venom showed a low anti-leishmanial activity in higher concentrations (IC50 value of 281.00 +/- 9.50 mu g/ml). The main fractions of Cdca venom were isolated and assayed under similar conditions used for assessing crude venom. The most active fractions were gyroxin and crotamine that had IC50 values of 3.80 +/- 0.52 mu g/ml and 19.95 +/- 4.21 mu g/ml, respectively. Convulxin also inhibited parasite growth rate, although this effect was not dose-dependent. Crotoxin was the least effective fraction with an IC50 value of 99.80 +/- 2.21 mu g/ml. None of the protein fractions presented cytotoxic effects against J774 cells in culture. In vivo assays using BALB/c mice revealed that crotoxin and crotamine were the main toxic fractions. In conclusion, C. durissus cascavella venom has three main fractions with anti-leishmanial activity. These results open new possibilities to find proteins that might be used as possible agents against cutaneous leishmaniasis.

Comparative investigation of the cleavage step in the synthesis of model peptide resins: Implications for N-alpha-9-fluorenylmethyloxycarbonyl-solid phase peptide synthesis

Based on our studies of the stability of model peptide-resin linkage in acid media, we previously proposed a rule for resin selection and a final cleavage protocol applicable to the N-alpha-tert-butyloxycarbonyl (Boc)-peptide synthesis strategy. We found that incorrect choices resulted in decreases in the final synthesis yield, which is highly dependent on the peptide sequence, of as high as 30%. The present paper continues along this line of research but examines the N-alpha-9-fluorenylmethyloxycarbonyl (Fmoc)-synthesis strategy. The vasoactive peptide angiotensin II (All, DRVYIHPF) and its [Gly(8)]-All analogue were selected as model peptide resins. Variations in parameters such as the type of spacer group (linker) between the peptide backbone and the resin, as well as in the final acid cleavage protocol, were evaluated. The same methodology employed for the Boc strategy was used in order to establish rules for selection of the most appropriate linker-resin conjugate or of the peptide cleavage method, depending on the sequence to be assembled. The results obtained after treatment with four cleavage solutions and with four types of linker groups indicate that, irrespective of the circumstance, it is not possible to achieve complete removal of the peptide chains from the resin. Moreover, the Phe-attaching peptide at the C-terminal yielded far less cleavage (50-60%.) than that observed with the Gly-bearing sequences at the same position (70-90%). Lastly, the fastest cleavage occurred with reagent K acid treatment and when the peptide was attached to the Wang resin.