Development of type I genetic markers from expressed sequence tags in highly polymorphic species

Expressed sequence tag (EST) databases provide a primary source of nuclear DNA sequences for genetic marker development in non-model organisms. To date, the process has been relatively inefficient for several reasons: - 1) priming site polymorphism in the template leads to inferior or erratic amplification; - 2) introns in the target amplicon are too large and/or numerous to allow effective amplification under standard screening conditions, and; - 3) at least occasionally, a PCR primer straddles an exon–intron junction and is unable to bind to genomic DNA template. The first is only a minor issue for species or strains with low heterozygosity but becomes a significant problem for species with high genomic variation, such as marine organisms with extremely large effective population sizes. Problems arising from unanticipated introns are unavoidable but are most pronounced in intron-rich species, such as vertebrates and lophotrochozoans. We present an approach to marker development in the Pacific oyster Crassostrea gigas, a highly polymorphic and intron-rich species, which minimizes these problems, and should be applicable to other non-model species for which EST databases are available. Placement of PCR primers in the 3′ end of coding sequence and 3′ UTR improved PCR success rate from 51% to 97%. Almost all (37 of 39) markers developed for the Pacific oyster were polymorphic in a small test panel of wild and domesticated oysters.

Water addition, evaporation and water holding capacity of poultry litter

Litter moisture content has been related to ammonia, dust and odour emissions as well as bird health and welfare. Improved understanding of the water holding properties of poultry litter as well as water additions to litter and evaporation from litter will contribute to improved litter moisture management during the meat chicken grow-out. The purpose of this paper is to demonstrate how management and environmental conditions over the course of a grow-out affect the volume of water A) applied to litter, B) able to be stored in litter, and C) evaporated from litter on a daily basis. The same unit of measurement has been used to enable direct comparison—litres of water per square metre of poultry shed floor area, L/m2, assuming a litter depth of 5 cm. An equation was developed to estimate the amount of water added to litter from bird excretion and drinking spillage, which are sources of regular water application to the litter. Using this equation showed that water applied to litter from these sources changes over the course of a grow-out, and can be as much as 3.2 L/m2/day. Over a 56 day grow-out, the total quantity of water added to the litter was estimated to be 104 L/m2. Litter porosity, water holding capacity and water evaporation rates from litter were measured experimentally. Litter porosity decreased and water holding capacity increased over the course of a grow-out due to manure addition. Water evaporation rates at 25 °C and 50% relative humidity ranged from 0.5 to 10 L/m2/day. Evaporation rates increased with litter moisture content and air speed. Maintaining dry litter at the peak of a grow-out is likely to be challenging because evaporation rates from dry litter may be insufficient to remove the quantity of water added to the litter on a daily basis.

Genetic characterization of field-evolved resistance to phosphine in the rusty grain beetle, Cryptolestes ferrugineus (Laemophloeidae: Coleoptera)

Inheritance of resistance to phosphine fumigant was investigated in three field-collected strains of rusty grain beetle, Cryptolestes ferrugineus, Susceptible (S-strain), Weakly Resistant (Weak-R) and Strongly Resistant (Strong-R). The strains were purified for susceptibility, weak resistance and strong resistance to phosphine, respectively, to ensure homozygosity of resistance genotype. Crosses were established between S-strain × Weak-R, S-strain × Strong-R and Weak-R × Strong-R, and the dose mortality responses to phosphine of these strains and their F1, F2 and F1-backcross progeny were obtained. The fumigations were undertaken at 25 °C and 55% RH for 72 h. Weak-R and Strong-R showed resistance factors of 6.3 × and 505 × compared with S-strain at the LC50. Both weak and strong resistances were expressed as incompletely recessive with degrees of dominance of − 0.48 and − 0.43 at the LC50, respectively. Responses of F2 and F1-backcross progeny indicated the existence of one major gene in Weak-R, and at least two major genes in Strong-R, one of which was allelic with the major factor in Weak-R. Phenotypic variance analyses also estimated that the number of independently segregating genes conferring weak resistance was 1 (nE = 0.89) whereas there were two genes controlling strong resistance (nE = 1.2). The second gene, unique to Strong-R, interacted synergistically with the first gene to confer a very high level of resistance (~ 80 ×). Neither of the two major resistance genes was sex linked. Despite the similarity of the genetics of resistance to that previously observed in other pest species, a significant proportion (~ 15 to 30%) of F1 individuals survived at phosphine concentrations higher than predicted. Thus it is likely that additional dominant heritable factors, present in some individuals in the population, also influenced the resistance phenotype. Our results will help in understanding the process of selection for phosphine resistance in the field which will inform resistance management strategies. In addition, this information will provide a basis for the identification of the resistance genes.

Genetic characterization of field-evolved resistance to phosphine in the rusty grain beetle, Cryptolestes ferrugineus (Laemophloeidae: Coleoptera)

Inheritance of resistance to phosphine fumigant was investigated in three field-collected strains of rusty grain beetle, Cryptolestes ferrugineus, Susceptible (S-strain), Weakly Resistant (Weak-R) and Strongly Resistant (Strong-R). The strains were purified for susceptibility, weak resistance and strong resistance to phosphine, respectively, to ensure homozygosity of resistance genotype. Crosses were established between S-strain × Weak-R, S-strain × Strong-R and Weak-R × Strong-R, and the dose mortality responses to phosphine of these strains and their F1, F2 and F1-backcross progeny were obtained. The fumigations were undertaken at 25 °C and 55% RH for 72 h. Weak-R and Strong-R showed resistance factors of 6.3 × and 505 × compared with S-strain at the LC50. Both weak and strong resistances were expressed as incompletely recessive with degrees of dominance of − 0.48 and − 0.43 at the LC50, respectively. Responses of F2 and F1-backcross progeny indicated the existence of one major gene in Weak-R, and at least two major genes in Strong-R, one of which was allelic with the major factor in Weak-R. Phenotypic variance analyses also estimated that the number of independently segregating genes conferring weak resistance was 1 (nE = 0.89) whereas there were two genes controlling strong resistance (nE = 1.2). The second gene, unique to Strong-R, interacted synergistically with the first gene to confer a very high level of resistance (~ 80 ×). Neither of the two major resistance genes was sex linked. Despite the similarity of the genetics of resistance to that previously observed in other pest species, a significant proportion (~ 15 to 30%) of F1 individuals survived at phosphine concentrations higher than predicted. Thus it is likely that additional dominant heritable factors, present in some individuals in the population, also influenced the resistance phenotype. Our results will help in understanding the process of selection for phosphine resistance in the field which will inform resistance management strategies. In addition, this information will provide a basis for the identification of the resistance genes.

Does the addition of Clonidine to lumbar nerve root blocks improve outcome? A randomised, prospective, single-blinded controlled pilot study

Purpose To evaluate if adding clonidine to a standard nerve root block containing local anaesthetic and steroid improved the outcome of patients with severe lumbar nerve root pain secondary to MRI proven lumbar disc prolapse. Methods We undertook a single blind, prospective, randomised controlled trial evaluating 100 consecutive patients with nerve root pain secondary to lumbar disc prolapse undergoing trans-foraminal epidural steroid injection either with or without the addition of clonidine. 50 patients were allocated to each arm of the study. The primary outcome measure was the avoidance of a second procedure- repeat injection or micro-discectomy surgery. Secondary outcome measures were also studied: pain scores for leg and back pain using a visual analogue scale (VAS), the Roland Morris Disability Questionnaire (RMDQ) and the Measure Your Own Medical Outcome Profile (MYMOP). Follow up was carried out at 6 weeks, 6 months and 1 year. Results No serious complications occurred. Of the 50 patients who received the addition of clonidine, 56% were classified as successful injections, with no further intervention required, as opposed to 40% who received the standard injection. This difference did not reach statistical significance (p=0.109, chi-squared test). All secondary measures showed no statistically significant differences between the groups except curiously, the standard group who had been classified as successful had better leg pain relief than the clonidine group (p=0.026) at 1 year. Conclusions This pilot study has shown a 16% treatment effect with adding clonidine to lumbar nerve root blocks and that it is a safe injectate for this purpose.

Susceptibility to sulfuryl fluoride and lack of cross-resistance to phosphine in developmental stages of the red flour beetle, Tribolium castaneum (Coleoptera: Tenebrionidae)

BACKGROUND Our aim was to ascertain the potential of sulfuryl fluoride (SF) as an alternative fumigant to manage phosphine-resistant pests. We tested the susceptibility of all life stages of red flour beetle, Tribolium castaneum (Herbst), to SF and assessed the presence of cross-resistance to this fumigant in phosphine-resistant strains of this species. RESULTS Analysis of dose–response data indicated that the egg was the stage most tolerant to SF under a 48 h exposure period. At LC50, eggs were 29 times more tolerant than other immature stages and adults, and required a relatively high concentration of 48.2 mg L−1 for complete mortality. No significant differences in tolerance to SF were observed among the three larval instars, pupae and adults, and all of these stages were controlled at a low concentration of 1.32 mg L−1. Phosphine-resistant strains did not show cross-resistance to SF. CONCLUSION Our research concluded that the current maximum registered rate of SF, 1500 gh m−3, is adequate to control all the post-embryonic life stages of T. castaneum over a 48 h fumigation period, but it will fail to achieve complete mortality of eggs, indicating the risk of some survival of eggs under this short exposure period. As there is no cross-resistance to SF in phosphine-resistant insects, it will play a key role in managing phosphine resistance in stored-grain insect pests. © 2014 Commonwealth of Australia. Pest Management Science © 2014 Society of Chemical Industry

Sorption and desorption of sulfuryl fluoride by wheat, flour and semolina

Sulfuryl fluoride (SF) has been developed as a fumigant for control of insect pests in stored grain. However, there is very limited information on the sorption behaviour of this fumigant, which can be critical to its bioactivity, application and potential for residues. We undertook a comprehensive laboratory study of the sorption and desorption of SF by wheat (bread and durum), flour and semolina at 15, 25 and 35 °C, moisture contents 12% and 15%, and concentration × time combinations at CT = 1500 mgh/L (4.167 mg/L × 360 h, 8.928 mg/L × 168 h and 31.25 mg/L × 48 h). At each dosage, sorption rate increased as commodity temperature and moisture content increased. The highest rates of sorption occurred at 35 °C and 15% m.c., and lowest rates at 15 °C and 12% m.c., and the rate was independent of initial concentration. Sorption followed first order reaction kinetics described by the exponential decay equation, Ct = C0·e−k*t, where k is the sorption rate constant. The most important factors determining the rate of sorption were commodity particle size (exposed surfaces) and temperature. Little sorption of fumigant occurred within the first 24 h whereas longer fumigation times resulted in significant sorption. Unbound SF was rapidly lost from the commodity upon aeration with no further desorption detected under any of the test conditions.

Genetic conservation of Phosphine Resistance in the Rice Weevil Sitophilus oryzae (L.)

High levels of resistance to phosphine in the rice weevil Sitophilus oryzae have been detected in Asian countries including China and Vietnam, however there is limited knowledge of the genetic mechanism of resistance in these strains. We find that the genetic basis of strong phosphine resistance is conserved between strains of S. oryzae from China, Vietnam and Australia. Each of four strongly resistant strains has an identical amino acid variant in the encoded dihydrolipoamide dehydrogenase (DLD) enzyme that was previously identified as a resistance factor in Rhyzopertha dominica and Tribolium castaneum. The unique amino acid substitution, Asparagine > Threonine (N505T) of all strongly resistant S. oryzae corresponds to the position of an Asparagine > Histidine variant (N506H) that was previously reported in strongly resistant R. dominica. Progeny (F16 and F18) from two independent crosses showed absolute linkage of N505T to the strong resistance phenotype, indicating that if N505T was not itself the resistance variant that it resided within 1 or 2 genes of the resistance factor. Non-complementation between the strains confirmed the shared genetic basis of strong resistance, which was supported by the very similar level of resistance between the strains, with LC50 values ranging from 0.20 to 0.36 mgL-1 for a 48 hour exposure at 25°C. Thus, the mechanism of high level resistance to phosphine is strongly conserved between R. dominica, T. castaneum and S. oryzae. A fitness cost associated with strongly resistant allele was observed in segregating populations in the absence of selection.

Water activity of poultry litter: Relationship to moisture content during a grow-out

Poultry grown on litter floors are in contact with their own waste products. The waste material needs to be carefully managed to reduce food safety risks and to provide conditions that are comfortable and safe for the birds. Water activity (Aw) is an important thermodynamic property that has been shown to be more closely related to microbial, chemical and physical properties of natural products than moisture content. In poultry litter, Aw is relevant for understanding microbial activity; litter handling and rheological properties; and relationships between in-shed relative humidity and litter moisture content. We measured the Aw of poultry litter collected throughout a meat chicken grow-out (from fresh pine shavings bedding material to day 52) and over a range of litter moisture content (10–60%). The Aw increased non-linearly from 0.71 to 1.0, and reached a value of 0.95 when litter moisture content was only 22–33%. Accumulation of manure during the grow-out reduced Aw for the same moisture content. These results are relevant for making decisions regarding litter re-use in multiple grow-outs as well as setting targets for litter moisture content to minimise odour, microbial risks and to ensure necessary litter physical conditions are maintained during a grow-out. Methods to predict Aw in poultry litter from moisture content are proposed.

Characterisation of wood–water relationships and transverse anatomy and their relationship to drying degrade

Characterisation of a number of key wood properties utilising ‘state of the art’ tools was achieved for four commercial Australian hardwood species: Corymbia citriodora, Eucalyptus pilularis, Eucalyptus marginata and Eucalyptus obliqua. The wood properties were measured for input into microscopic (cellular level) and macroscopic (board level) vacuum drying models currently under development. Morphological characterisation was completed using a combination of ESEM, optical microscopy and a custom vector-based image analysis software. A clear difference in wood porosity, size, wall thickness and orientation was evident between species. Wood porosity was measured using a combination of fibre and vessel porosity. A highly sensitive microbalance and scanning laser micrometres were used to measure loss of moisture content in conjunction with directional shrinkage on micro-samples of E. obliqua to investigate the validity of measuring collapse-free shrinkage in very thin sections. Collapse-free shrinkage was characterised, and collapse propensity was verified when testing thicker samples. Desorption isotherms were calculated for each species using wood–water relations data generated from shrinkage experiments. Fibre geometry and wood shrinkage anisotropy were used to explain the observed difficulty in drying of the different species in terms of collapse and drying stress-related degrade.

Does Fumigation of Durum Wheat and Semolina with Sulfuryl Fluoride affect Quality of the Grain, Semolina and derived Spaghetti and Bread?

There is no information on the effect of sulfuryl fluoride (SF) on durum wheat technological properties and products made from fumigated durum wheat. Durum wheat and semolina were exposed to a range of SF applications under conditions that might be typically encountered in bulk storage facilities used in many countries. SF greatly reduced the germination percentage of fumigated durum wheat with increasing impact under higher SF concentration, grain moisture content, and fumigation temperature. SF greatly reduced seed germination percentage impacting more the higher the SF concentration. SF had little to no effects on grain test weight, 1000 grain weight, hardness, protein content, semolina ash content and mixograph properties. At the highest SF concentration (31.25 mg/L for 48 h) there was a tendency for pasta cooking loss to be increased but still acceptable while other pasta properties were largely unaffected. Fumigation with SF did not have any impact on the baking properties of a wholemeal durum flour-commercial flour mix. Therefore, SF is not recommended if the grains are to be used as seeds for agricultural production but for the production of semolina, pasta and bread, SF used under typical fumigation conditions has little to no impact on technological properties of durum wheat.

Multijurisdictional fisheries performance reporting: How Australia’s nationally standardised approach to assessing stock status compares

Australian marine wild-capture fisheries are managed by eight separate jurisdictions. Traditionally, fishery status reports have been produced separately by most of these jurisdictions, assessing the fish stocks they manage, and reporting on the effectiveness of their fisheries management. However, the format, the type of stock status assessments, the thresholds and terminology used to describe stock status and the classification frameworks have varied over time and among jurisdictions. These differences complicate efforts to understand stock status on a national scale. They also create potential misunderstanding among the wider community about how to interpret information on the status of fish stocks, and the fisheries management and science processes more generally. This is especially true when considering stocks that are shared across two or more jurisdictional boundaries. A standardised approach was developed in 2011 leading to production of the first national Status of key Australian fish stocks reports in 2012, followed by a second edition in 2014 (www.fish.gov.au). Production of these reports was the first step towards a broader national approach to reporting on the performance of Australian fisheries for target species and for wider ecosystem and socioeconomic consequences. This paper outlines the challenges associated with moving towards national performance reporting for target fish stocks and Australia’s successes so far. It also outlines the challenges ahead, in particular those relating to reporting more broadly on the status of entire fisheries. Comparisons are drawn between Australia and New Zealand and more broadly between Australia and other countries.

Following fashion: Visible progressiveness and the social construction of firm value

A central tenet underlying studies on management fashions is that the diffusion of novel forms, models and techniques is driven by an institutional norm of progress, which is the societal expectation that managers will continuously use 'new and improved' management practices. We add to the literature on management fashions by arguing that, if the display of progressiveness in the manner of managing and organizing is expected of organizations, firms that are visibly progressive would be evaluated more positively by organizational audiences following this institutional prescription. Using article counts of co-occurrences of firms and various fashionable management practices in Wall Street Journal, we hypothesize positive effects of such associations on security analysts' evaluations of these firms. Results support this hypothesis. Our study enriches the management fashion literature by highlighting the consequential relevance of organizational adherence to the norm of progress.

Positive associations of serum Perfluoroalkyl substances with uric acid and hyperuricemia in children from Taiwan

To investigate the risk of hyperuricemia in relation to Perfluoroalkyl substances (PFASs) in children from Taiwan, 225 Taiwanese children aged 12-15 years were recruited from 2009 to 2010. Linear and logistic regression models were employed to examine the influence of PFASs on serum uric acid levels. Findings revealed that eight of ten PFASs analyses were detected in > 94% of the participants' serum samples. Multivariate linear regression models revealed that perfluorooctanic acid (PFOA) was positively associated with serum uric acid levels (β=0.1463, p<0.05). Of all the PFASs analyses, only PFOA showed a significant effect on elevated levels of hyperuricemia (aOR=2.16, 95%CI: 1.29-3.61). When stratified by gender, the association between serum PFOA and uric acid levels was only evident among boys (aOR=2.76, 95%CI: 1.37-5.56). In conclusion, PFOA was found to be associated with elevated serum levels of uric acid in Taiwanese children, especially boys. Further research is needed to elucidate these links.