Predição genômica utilizando painéis de marcadores moleculares com diferentes densidades, em bovinos da raça Nelore

Pós-graduação em Genética e Melhoramento Animal - FCAV

Assinaturas de seleção em bovinos da raça Canchim

Pós-graduação em Genética e Melhoramento Animal - FCAV

Aspectos da furação do titânio 6Al4V com broca de aço rápido sinterizado e broca de metal duro

Pós-graduação em Engenharia Mecânica - FEG

Análise da heterocedasticidade em bubalinos utilizando informações genômicas

Pós-graduação em Genética e Melhoramento Animal - FCAV

Hot turning of a difficult-to-machine steel (sae xev-f) aided by infrared radiation

A possible way for increasing the cutting tool life can be achieved by heating the workpiece in order to diminish the shear stress of material and thus decrease the machining forces. In this study, quartz electrical resistances were set around the workpiece for heating it during the turning. In the tests, heat-resistant austenitic alloy steel was used, hardenable by precipitation, mainly used in combustion engine exhaustion valves, among other special applications for industry. The results showed that in the hot machining the cutting tool life can be increased by 340% for the highest cutting speed tested and had a reduction of 205% on workpiece surface roughness, accompanied by a force decrease in relation to conventional turning. In addition, the chips formed in hot turning exhibited a stronger tendency to continuous chip formation indicating less energy spent in material removal process. Microhardness tests performed in the workpieces subsurface layers at 5 m depth revealed slightly higher values in the hot machining than in conventional, showing a tendency toward the formation of compressive residual stress into plastically deformed layer. The hot turning also showed better performance than machining using cutting fluid. Since it is possible to avoid the use of cutting fluid, this machining method can be considered better for the environment and for the human health.

A Genome-Wide Association Study for Morphometric Traits in Quarter Horse

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Imputation of non-genotyped individuals using genotyped progeny in Nellore, a Bos indicus cattle breed

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Natural-rubber-based flexible microfluidic device

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Accuracy of genotype imputation in Nelore cattle

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influência da geometria de corte no torneamento do eucalipto sp

In contrast to what happened in the past where it was possible to select which species had a lower degree of variation, it is now necessary to use fast-growing species with efficient processing. For that we use the wood of Eucalyptus sp and studies related to the machining processes and their parameters such as wear of cutting tools and roughness. The present work aims to analyze the influence of geometry of cutting tools of high speed steel and the influence of the diameter of the final pieces in the process of turning wood of Eucalyptus sp in relation to power consumption, roughness, temperature machining, chip formed and wear of cutting tools. It was observed that the smaller the diameter of the end parts and greater wear of the tools, the worse quality of the machined surfaces and the greater the power consumed in the process of machining

Desenvolvimento da técnica de MALDI Imaging utilizando tecidos animais

Currently the study of important molecular compounds present in low abundance in some tissues has been a challenge for proteomic analysis classic. An analysis requires more exploratory investigation of small regions of a tissue or a group of cells. MALDI Imaging Technology (MSI) is an application of mass spectrometry facing the chemical analysis of intact tissues. Thus, advances in mass spectrometry MALDI being obtained by the integration of histology, the best methods and automation are the main tools of data analysis. This tool has become essential to analyze the spatial distribution of peptides and proteins throughout the tissue sections, providing an enormous amount of data with minimum sample preparation. Thus, the aim of this study was to develop the technique of MALDI Imaging using tissue from glioblastoma multiforme (GBM), a form of most common malignant tumor in the brain. For this we used the printer chemical ChIP-1000 (Chemical Inkjet Printer, Shimadzu) and mass spectrometer type Maldi-ToF-ToF (Axima Performance, Shimadzu), a search of the identifications were performed in databases such as SwissProt. We identified more than forty proteins with diverse functions such as proteins F-actin-capping and Thymosin to the structure and organization cellular and proteins such several Tumor necrosis factor receptor development-related pathology. The development of this technique will permit to carry-out proteomic analysis directly into the tissue, enabling earlier diagnosis of diseases, as well as the identification and characterization of potential biomarkers of disease.

Mapeamento geológico no alvo Morro do Corcunda - Greenstone Belt Pilar de Goiás (Santa Terezinha-GO)

The following work refers to a geologic mapping in the Morro do Corcunda target, located between the cities of Pilar of Goiás and Santa Terezinha in the northwest portion of the State of Goiás. This mapping was carried through in 1:10,000 scale and covers an area of approximately 60km2. Collections of samples had been carried through for laborarorial analysis, and from those twenty-three thin scetions have been produced in order to describe the main lithologies that occur in the area. It was possible to observe anomalous gold targets in the region through chip samples carried through during the stage of field work. The gathered field data and the ones that have been made available by the company Yamana Gold Incorporation were congregated, and a data integration was carried through. This integration made possible the correlation of the litologies found in field with the Greenstone Belt Pilar de Goiás sequence and the structural evolution of the area.

Estudo da influência da aplicação do fluido de corte no torneamento da liga de alumínio AA7075

One of the ways to minimize the effects of unproductive time caused by tool wear can be achieved by introducing an efficient system of lubrication and cooling in the process. However, in the last decade the research had the goal to restrict the maximum use of refrigerants and / or lubricants in metal-mechanical production. The important factors that justify this procedure include the operational costs of production, ecological issues, and the legal requirements of environmental conservation and preservation of human health. The purpose of the proposed work is the study of machining by turning with the focus on the influence caused by the application of cutting fluid in several ways of application (abundant and MQF) and also by comparing the results obtained by machining without the presence of fluid . For this purpose, the turning tests are conducted using an aluminum alloy (AA 7075). The response variables to be analyzed were obtained from the roughness (Ra and Ry), the stresses presented (VB) and their progression in relation to the cutting length achieved, the type of chip formed, in addition to changes in the degree of finish (roughness) presented by the turned parts. The results of this study should provide more detailed information about the actual influence of cutting fluids in turning this alloy, which are characterized by high rates of deformation when the formation of damaging your chip machining and also the quality of surface generated. Therefore, it is expected to provide subsidies to promote the optimization of machining this alloy making the most of the role of cutting fluid

Projeto de um Multiplicador Divisor Anal´ogico em tecnologia CMOS para uso em controlador fuzzy tipo-2 intervalar

The main objective of the presented study is the design of a analog multiplier-divider as integrant part of the type-reducer circuit of type-2 fuzzy controller chip. The proposed circuit is a multiplier/divider which operates in current mode, in the CMOS technology with a supply voltage of 1.8 V.The circuit simulation was performed in PSPICE software with simulation model provided by AMS (Austria Mikro Systems International) in CMOS technology 0.35μm

Clinical fractures of veneered zirconia single crowns

Crowns made from an yttria-stabilized tetragonal zirconia polycrystals (3Y-TZP) core with a porcelain veneer have shown high clinical failure rates. Manifestations of clinical failure in veneering ceramic ranges from a single chip to an extended fracture. Core failures are uncommon but usually are catastrophic. This article examines the possible causes of failure in zirconia systems and presents a case report involving the diagnosis and repair of three different types of failure in six 3Y-TZP/porcelain crowns.