The use of spatial impulse responses to characterise flexible forming processes with mobile tools

A novel test method for the characterisation of flexible forming processes is proposed and applied to four flexible forming processes: Incremental Sheet Forming (ISF), conventional spinning, the English wheel and power hammer. The proposed method is developed in analogy with time-domain control engineering, where a system is characterised by its impulse response. The spatial impulse response is used to characterise the change in workpiece deformation created by a process, but has also been applied with a strain spectrogram, as a novel way to characterise a process and the physical effect it has on the workpiece. Physical and numerical trials to study the effects of process and material parameters on spatial impulse response lead to three main conclusions. Incremental sheet forming is particularly sensitive to process parameters. The English wheel and power hammer are strongly similar and largely insensitive to both process and material parameters. Spinning develops in two stages and is sensitive to most process parameters, but insensitive to prior deformation. Finally, the proposed method could be applied to modelling, classification of existing and novel processes, product-process matching and closed-loop control of flexible forming processes. © 2012 Elsevier B.V.

Maturity grids as tools for change management

One method to assess organizational capabilities is a maturity grid. MATURITY GRIDS AS TOOLS FOR CHANGE MANAGEMENT A maturity grid assessment is typically structured around a matrix or a grid. It consists of a series of cells where ...

Analysis of document-mining techniques and tools for technology intelligence: Discovering knowledge from technical documents

This research proposes a method for extracting technology intelligence (TI) systematically from a large set of document data. To do this, the internal and external sources in the form of documents, which might be valuable for TI, are first identified. Then the existing techniques and software systems applicable to document analysis are examined. Finally, based on the reviews, a document-mining framework designed for TI is suggested and guidelines for software selection are proposed. The research output is expected to support intelligence operatives in finding suitable techniques and software systems for getting value from document-mining and thus facilitate effective knowledge management. Copyright © 2012 Inderscience Enterprises Ltd.

Dynamic behaviour of gas jets in laser cutting

The efficiency and overall quality of a laser cutting operation is highly dependent on the assist gas parameters. The desire to cut thicker material has led to the observation of small process operating windows for thicker sections. The gas jet delivery and subsequent dynamical behaviour have significant effects on the cutting operation as the sample thickness increases. To date, few workers have examined the dynamical behaviour of the gas jet. This paper examines the characteristics of oxygen gas jets during CO2 laser cutting of steel. Particular emphasis is placed on the mass transfer effects that are operating within the kerf. Oxygen concentration levels within a model kerf are measured for various laser cutting set-ups. The results show a substantial reduction in oxygen concentration within the kerf. A system for oxygen concentration maintenance is described and cutting results from this system are compared with conventional techniques for cutting steels in the range 10 to 20mm thick. A theoretical analysis of turbulent mass transfer within a kerf is presented and compared with experiment.

Application of gel-casting to the fabrication of 1-3 piezoelectric ceramic-polymer composites for high-frequency ultrasound devices

A modified gel-casting technique was used to fabricate a 1-3 piezoelectric ceramic/polymer composite substrate formed by irregular-shaped pillar arrays of small dimensions and kerfs. This technique involves the polymerization of aqueous piezoelectric (PZT) suspensions with added water-soluble epoxy resin and polyamine-based hardener that lead to high strength, high density and resilient ceramic bodies. Soft micromoulding was used to shape the ceramic segments, and micropillars with lateral features down to 4 m and height-to-width aspect ratios of ∼10 were achieved. The composite exhibited a clear thickness resonance mode at approximately 70 MHz and a k eff ∼ 0.51, demonstrating that the ceramic micropillars possess good electrical properties. Furthermore, gel-casting allows the fabrication of ceramic structures with non-conventional shapes; hence, device design is not limited by the standard fabrication methods. This is of particular benefit for high-frequency transducers where the critical design dimensions are reduced. © 2012 IOP Publishing Ltd.

Electrical transport and magnetic properties of Mn3O4-La0.7Ca0.3MnO3 ceramic composites prepared by a one-step spray-drying technique

La0.7Ca0.3MnO3/Mn3O4 composites can be synthesized in one step by thermal treatment of a spray-dried precursor, instead of mixing pre-synthesized powders. Another advantage of this composite system is that a long sintering step can be used without leading to significant modification of the manganite composition. The percolation threshold is reached at ∼20 vol% of manganite phase. The 77 K low field magnetoresistance is enhanced to ∼11% at 0.15 T when the composition is close to the percolation threshold. © 2007 Elsevier Ltd. All rights reserved.

Unsteady penetration of a target by a liquid jet.

It is widely acknowledged that ceramic armor experiences an unsteady penetration response: an impacting projectile may erode on the surface of a ceramic target without substantial penetration for a significant amount of time and then suddenly start to penetrate the target. Although known for more than four decades, this phenomenon, commonly referred to as dwell, remains largely unexplained. Here, we use scaled analog experiments with a low-speed water jet and a soft, translucent target material to investigate dwell. The transient target response, in terms of depth of penetration and impact force, is captured using a high-speed camera in combination with a piezoelectric force sensor. We observe the phenomenon of dwell using a soft (noncracking) target material. The results show that the penetration rate increases when the flow of the impacting water jet is reversed due to the deformation of the jet-target interface--this reversal is also associated with an increase in the force exerted by the jet on the target. Creep penetration experiments with a constant indentation force did not show an increase in the penetration rate, confirming that flow reversal is the cause of the unsteady penetration rate. Our results suggest that dwell can occur in a ductile noncracking target due to flow reversal. This phenomenon of flow reversal is rather widespread and present in a wide range of impact situations, including water-jet cutting, needleless injection, and deposit removal via a fluid jet.

Developing ISO 14649-based conversational programming system for multi-channel complex machine tools

A multi-channel complex machine tool (MCCM) is a versatile machining system equipped with more than two spindles and turrets for both turning and milling operations. Despite the potential of such a tool, the value of the hardware is largely dependent on how the machine tools are effectively programmed for machining. In this paper we consider a shop-floor programming system based on ISO 14649 (called e-CAM), the international standard for the interface between computer-aided manufacture (CAM) and computer numerical control (CNC). To be deployed in practical industrial usage a great deal of research has to be carried out. In this paper we present: 1) Design consideration for an e-CAM system, 2) The architecture design of e-CAM, 3) Major algorithms to fulfill the modules defined in the architecture, and 4) Implementation details.

Motor systems: reaching out and grasping the molecular tools.

Two recent studies provide important insights into the organization of premotor circuitries, showing that control of highly-specific skilled forelimb movements, such as reaching and grasping, requires activation of specific subpopulations of neurons in the brainstem and spinal cord.

Technology management tools: Generalization, integration and configuration

Managers in technology-intensive businesses need to make decisions in complex and dynamic environments. Many tools, frameworks and processes have been developed to support managers in these situations, leading to a proliferation of such approaches, with little consistency in terminology or theoretical foundation, and a lack of understanding of how such tools can be linked together to tackle management challenges in an integrated way. As a step towards addressing these issues, this paper proposes the concept of an integrated 'toolkit', incorporating generalized forms of three core technology management tools that support strategic planning (roadmapping, portfolio analysis and linked analysis grids). © 2006 World Scientific Publishing Company.

Diode-end-pumped passively mode-locked ceramic Nd : YAG Laser with a semiconductor saturable mirror

We report on a diode- pumped CW passively mode locked ceramic Nd: YAG laser with SESAM ( semiconductor saturable absorber mirror), wavelength 1064nm. At a pump power of 7.6w, the pulse width was estimated to be similar to 8.3ps with repetition rate similar to 130MHz and the average output power was 1.59w. To our knowledge, this was the first demonstration that ceramic Nd: YAG was used for diode pumped CW passively mode locking. (C) 2005 Optical Society of America.