Electronic transport in low temperature nanocrystalline silicon thin-film transistors obtained by Hot-Wire CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) obtained by hot-wire chemical vapour deposition (HWCVD) at low substrate temperature (150 °C) has been incorporated as the active layer in bottom-gate thin-film transistors (TFTs). These devices were electrically characterised by measuring in vacuum the output and transfer characteristics for different temperatures. The field-effect mobility showed a thermally activated behaviour which could be attributed to carrier trapping at the band tails, as in hydrogenated amorphous silicon (a-Si:H), and potential barriers for the electronic transport. Trapped charge at the interfaces of the columns, which are typical in nc-Si:H, would account for these barriers. By using the Levinson technique, the quality of the material at the column boundaries could be studied. Finally, these results were interpreted according to the particular microstructure of nc-Si:H.

Análisis de sistemas bucoadhesivos

[spa]Objetivo: El objetivo de este estudio es el diseño de un parche bucoadhesivo para la administración transbucal de clorhidrato de doxepina utilizando diferentes polímeros así como la caracterización de dichos sistemas en cuanto al análisis calorimétrico y la capacidad de hinchamiento.Materiales y métodos: Se ha utilizado clorhidrato de doxepina y diferentes polímeros, carboximetilcelulosa sódica, hidroxipropilmetilcelulosa y chitosan. La calorimetría diferencial de barrido (DSC) se ha realizado en un dispositivo Mettler FP 80 equipado con un horno FP 85 y la capacidad de hinchamiento utilizando placas de agar.Resultados: Se obtienen termogramas de los parches y las mezclas físicas donde se observan transiciones endotérmicas entre 30 y 120º C y el pico endotérmico del principio activo en las mezclas físicas binarias. La entalpía de deshidratación es similar en los polímeros de carboximetilcelulosa sódica y chitosan (281 J/g) siendo menor en la película de hidroxipropilmetilcelulosa (251 J/g), al igual que el porcentaje de hidratación donde se demuestra que los parches elaborados con hidroxipropilmetilcelulosa presenta menor tendencia a captar agua (55,91 %) frente al 67,04 % y 67,30 % de la carboximetilcelulosa sódica y chitosan, respectivamente.Conclusión: Los resultados obtenidos muestran que existe compatibilidad entre los componentes de la formulación y los datos de entalpía se correlacionan con los datos obtenidos en el ensayo de hinchamiento.[eng]The aim of this study is to design a bucoadhesive patch for the transbuccal administration of doxepin hydrochloride using different polymers as well as the characterization of these systems for calorimetric analysis and the swelling capacity. Materials and methods: Doxepin hydrochloride was used as well as various polymers; carboxymethylcellulose sodium, hydroxypropylmethyl cellulose and chitosan. Differential scanning calorimetry (DSC) was carried out using a Mettler FP 80 device equipped with a FP 85 oven and the swelling capacity using agar plates. Results: Thermograms obtained patches and physical mixtures where there are endothermic transitions between 30 and 120º C and the endothermic peak of the active principle in binary physical mixtures. Dehydration enthalpy is similar in polymers of carboxymethylcellulose sodium and chitosan (281 J/g), the film having less hydroxypropylmethylcellulose (251 J/g), the percentage of moisture shows that the patches prepared with hydroxypropylmethylcellulose have less tendency to collect water (55.91 %) compared to 67.04 % and 67.30 % with sodium carboxymethylcellulose and chitosan, respectively. Conclusion: The results show that there is compatibility between the components of the formulation and the enthalpy data correlate

Microdoping compensation of microcrystalline silicon obtained by Hot-Wire Chemical Vapour Deposition

Undoped hydrogenated microcrystalline silicon was obtained by hot-wire chemical vapour deposition at different silane-to-hydrogen ratios and low temperature (<300 °C). As well as technological aspects of the deposition process, we report structural, optical and electrical characterizations of the samples that were used as the active layer for preliminary p-i-n solar cells. Raman spectroscopy indicates that changing the hydrogen dilution can vary the crystalline fraction. From electrical measurements an unwanted n-type character is deduced for this undoped material. This effect could be due to a contaminant, probably oxygen, which is also observed in capacitance-voltage measurements on Schottky structures. The negative effect of contaminants on the device was dramatic and a compensated p-i-n structure was also deposited to enhance the cell performance.

Sensitive photonic system to measure oxidative potential of airborne nanoparticles and ROS levels in exhaled air

A photonic system has been developed that enables sensitive quantitative determination of reactive oxygen species (ROS) - mainly hydrogen peroxide (H2O2) - in aerosol samples such as airborne nanoparticles and exhaled air from patients. The detection principle relies on the amplification of the absorbance under multiple scattering conditions due to optical path lengthening [1] and [2]. In this study, the presence of cellulose membrane that acts as random medium into the glass optical cell considerably improved the sensitivity of the detection based on colorimetric FOX assay (FeII/orange xylenol). Despite the loss of assay volume (cellulose occupies 75% of cell volume) the limit of detection is enhanced by one order of magnitude reaching the value of 9 nM (H2O2 equivalents). Spectral analysis is performed automatically with a periodicity of 5 to 15 s, giving rise to real-time ROS measurements. Moreover, the elution of air sample into the collection chamber via a micro-diffuser (impinger) enables quantitative determination of ROS contained in or generated from airborne samples. As proof-of-concept the photonic ROS detection system was used in the determination of both ROS generated from traffic pollution and ROS contained in the exhaled breath as lung inflammation biomarkers.

Polymeerien erotus ultrasuodatuksella

Työssä selvitettiin suodatusolosuhteiden vaikutusta neutraalien polymeerien pidättymiseen niiden vesiliuoksia suodatettaessa. Suodatuksissa käytettiin kahta regeneroidusta selluloosasta valmistettua ultrasuodatuskalvoa (Microdyn-Nadir UC 030T ja JSC STC Vladipor C 30V). Malliaineina käytettiin polyetyleeniglykolia ja dekstraania. Kirjallisuusosassa esiteltiin aluksi lyhyesti ultrasuodatus erotusmenetelmänä. Lisäksi käsiteltiin ultrasuodatuskalvojen huokoskoon karakterisointimenetelmiä ja selvitettiin polymeerien erottumiseen ultrasuodatuksen aikana vaikuttavia tekijöitä. Työn kokeellisessa osassa tutkittiin paineen ja virtausnopeuden vaikutusta malliaineiden pidättymiseen ultrasuodatuskalvoilla. Lisäksi pyrittiin löytämään suodatusolosuhteet, joissa toinen aineista läpäisisi suodatuskalvon lähes täydellisesti toisen konsentroituessa syöttöliuokseen. Työssä myös määritettiin tutkimuksissa käytetyille kalvoille katkaisukoko, joka kuvaa kalvon kykyä pidättää moolimassaltaan erikokoisia molekyylejä. Lisäksi kokeellisessa osassa selvitettiin työssä käytettyjen kalvojen tasalaatuisuutta vertailemalla keskenään samanlaisissa suodatusolosuhteissa eri kalvopaloilla tehtyjen suodatusten tuloksia. Työssä saatiin erotettua kaksi lähes samankokoista malliaineeksi valittua neutraalia polymeeriä toisistaan siten, että toinen aine pidättyi kalvolla huomattavasti toista ainetta paremmin. Parhaimpaan erotustulokseen päästiin, kun permeaattivuo kalvon läpi oli noin 400 l/(m2 h). Tällöin suodatuspaine oli noin 2 bar ja virtausnopeus alle 2 m/s. Työn aikana määritettyjen katkaisukokojen havaittiin poikkeavan huomattavasti kalvojen valmistajien ilmoittamista arvoista, mutta olevan kuitenkin samaa suuruusluokkaa kuin muiden tutkimusryhmien vastaaville ultrasuodatuskalvoille esittämät arvot. Työn tulosten perusteella C 30V olisi hieman tasalaatuisempi kalvo kuin UC 030T.

Efficiency and reliability enhancement of silicon nanocrystal field-effect luminescence from nitride-oxide gate stacks

We report on a field-effect light emitting device based on silicon nanocrystals in silicon oxide deposited by plasma-enhanced chemical vapor deposition. The device shows high power efficiency and long lifetime. The power efficiency is enhanced up to 0.1 %25 by the presence of a silicon nitride control layer. The leakage current reduction induced by this nitride buffer effectively increases the power efficiency two orders of magnitude with regard to similarly processed devices with solely oxide. In addition, the nitride cools down the electrons that reach the polycrystalline silicon gate lowering the formation of defects, which significantly reduces the device degradation.

Remediação de efluentes derivados da indústria de papel e celulose: tratamento biológico e fotocatalítico

The contribution of the industrial activities to the environmental contamination phenomena is evident. Great efforts are dedicated to the establishment of methodologies which permits an adequate treatment of the produced effluents, as a manner of minimizing the environmental impact of these wastes. The methodologies based on photocatalytic processes are very promise alternatives, because permits degradation of a great number of chemical substances of high toxic potential, without the use of other chemicals. The present work is an overview about the principal environmental aspects related with the paper and cellulose industry and the main alternatives employed for the reduction of environmental impact produced for its residues. The principal results of the photocatalytic treatment of this kind of effluents using metallic semiconductors is also showed.

The Proteolytic Activation of (H3N2) Influenza A Virus Hemagglutinin Is Facilitated by Different Type II Transmembrane Serine Proteases.

UNLABELLED: Cleavage of influenza virus hemagglutinin (HA) by host cell proteases is necessary for viral activation and infectivity. In humans and mice, members of the type II transmembrane protease family (TTSP), e.g., TMPRSS2, TMPRSS4, and TMPRSS11d (HAT), have been shown to cleave influenza virus HA for viral activation and infectivityin vitro Recently, we reported that inactivation of a single HA-activating protease gene,Tmprss2, in knockout mice inhibits the spread of H1N1 influenza viruses. However, after infection ofTmprss2knockout mice with an H3N2 influenza virus, only a slight increase in survival was observed, and mice still lost body weight. In this study, we investigated an additional trypsin-like protease, TMPRSS4. Both TMPRSS2 and TMPRSS4 are expressed in the same cell types of the mouse lung. Deletion ofTmprss4alone in knockout mice does not protect them from body weight loss and death upon infection with H3N2 influenza virus. In contrast,Tmprss2(-/-)Tmprss4(-/-)double-knockout mice showed a remarkably reduced virus spread and lung pathology, in addition to reduced body weight loss and mortality. Thus, our results identified TMPRSS4 as a second host cell protease that, in addition to TMPRSS2, is able to activate the HA of H3N2 influenza virusin vivo IMPORTANCE: Influenza epidemics and recurring pandemics are responsible for significant global morbidity and mortality. Due to high variability of the virus genome, resistance to available antiviral drugs is frequently observed, and new targets for treatment of influenza are needed. Host cell factors essential for processing of the virus hemagglutinin represent very suitable drug targets because the virus is dependent on these host factors for replication. We reported previously thatTmprss2-deficient mice are protected against H1N1 virus infections, but only marginal protection against H3N2 virus infections was observed. Here we show that deletion of two host protease genes,Tmprss2andTmprss4, strongly reduced viral spread as well as lung pathology and resulted in increased survival after H3N2 virus infection. Thus, TMPRSS4 represents another host cell factor that is involved in cleavage activation of H3N2 influenza virusesin vivo.

Characterization of Mechanically Alloyed Nanocrystalline Fe(Al): Crystallite Size and Dislocation Density

A nanostructured disordered Fe(Al) solid solution was obtained from elemental powders of Fe and Al using a high-energy ball mill. The transformations occurring in the material during milling were studied with the use of X-ray diffraction. In addition lattice microstrain, average crystallite size, dislocation density, and the lattice parameter were determined. Scanning electron microscopy (SEM) was employed to examine the morphology of the samples as a function of milling times. Thermal behaviour of the milled powders was examined by differential scanning calorimetry (DSC). The results, as well as dissimilarity between calorimetric curves of the powders after 2 and 20 h of milling, indicated the formation of a nanostructured Fe(Al) solid solution

Estudo comparativo da seletividade de um método cinético-catalítico: a determinação de Cr(VI) pela oxidação da o-dianisidina pelo peróxido de hidrogênio

Selectivity studies for the determination of Cr(VI) using the catalytic oxidation of the o-dianisidine by hydrogen peroxide showed two distincts situations. In the first, when interferents were studied by a univariate procedure, Cr(III) and Cu(II) cause serious interferences even at the 2:1 proportion, relative to Cr(VI), while Fe(III) interfered at the 15:1 ratio and EDTA at the 10:1 ratio. On the other hand, when a multivariate investigation was performed, Cr(III) did not present any significant principal effects and its significant interaction effects were negative, in contrast to EDTA, that presented positive interaction effects although, like Cr(III), did not show significant interaction effects. In view of the interferent's action it become necessary to separate Cr(VI) by extraction with methylisobutylketone in a chloridric acid medium before its determination in vegetals and in wastewater from a cellulose industry samples. Using this procedure, the method precision is ±0,5% at the 10 ng/mL Cr(VI) concentration level. The detection and quantification limits, calculated by means of absorbance measurements of ten replicates of blank reagents were 1,1 and 3,2 ng/mL, respectively. The results obtained with real samples showed a relative standard deviation between 1,2% and 3,0% relative to their reference values.

A técnica da reflectância difusa aplicada ao estudo da fluorescência de 2,3-naftalimidas n-substituídas com grupos alquila incluídas em b-ciclodextrina e adsorvidas em celulose microcristalina

The solution fluorescence of N-alkyl-2,3-naphthalimides (1-4) in polar protic and aprotic solvents was compared to the emission from solid samples resulting from the imide complexation with b-cyclodextrin or adsorption on the surface of microcrystalline cellulose. Solid samples of the inclusion complex 2,3-naphthalimides/b-cyclodextrin show maximum for fluorescence emission significantly different to the observed in methanolic solution. Beside this, a clear effect on the alkyl chain length could be observed for these samples which is probably due to differences in probe location inside the cyclodextrin cavity. The constancy for fluorescence quantum yield and fluorescence lifetime for the imides 1 - 4 adsorbed on microcrystalline cellulose suggests that, independently of the polarity of the solvent used for sample preparation, the probe is preferentially located on the cellulose surface. An increase of fluorescence quantum yield and fluorescence lifetime for solid samples, when compared to the values obtained in solution for the different solvents employed in this study (acetonitrile, methanol and water), is fully in accordance with a decrease of the probe mobility due to inclusion in b-cyclodextrin or to adsorption on cellulose.

Fractionation of wood hydrolysate by ultrafiltration membranes at high temperature

Ultrafiltration (UF) is already used in pulp and paper industry and its demand is growing because of the required reduction of raw water intake and the separation of useful compounds from process waters. In the pulp and paper industry membranes might be exposed to extreme conditions and, therefore, it is important that the membrane can withstand them. In this study, extractives, hemicelluloses and lignin type compounds were separated from wood hydrolysate in order to be able to utilise the hemicelluloses in the production of biofuel. The performance of different polymeric membranes at different temperatures was studied. Samples were analysed for total organic compounds (TOC), lignin compounds (UV absorption at 280 nm) and sugar. Turbidity, conductivity and pH were also measured. The degree of fouling of the membranes was monitored by measuring the pure water flux before and comparing it with the pure water flux after the filtration of hydrolysate. According to the results, the retention of turbidity was observed to be higher at lower temperature compared to when the filtrations were operated at high temperature (70 °C). Permeate flux increased with elevated process temperature. There was no detrimental effect of temperature on most of the membranes used. Microdyn-Nadir regenerated cellulose membranes (RC) and GE-Osmonics thin film membranes seemed to be applicable in the chosen process conditions. The Polyethersulphone (NF-PES-10 and UH004P) and polysulphone (MPS-36) membranes used were highly fouled, but they showed high retentions for different compounds.

A indústria petroquímica no próximo século: como substituir o petróleo como matéria-prima?

The world reserves of petroleum will finish in about 100 years. For a tropical country like Brazil, biomass will be the natural substitute for petroleum. For the best utilization of biomass, it first needs to be separated into its principal components: cellulose, hemicelluloses, lignins, vegetable and essential oils, non-structural carbohydrates, bark and foliage. All feedstocks for the chemical industry can be obtained from these biomass components, as shown in the first part of this paper. In the second part we discuss how the major products from petrochemicals can be obtained from the different biomass components. We show that Brazil can use different strategies, compared to other countries, to obtain petrochemical products, which could result in innovations. However, it is necessary that the government starts to invest immediately in order to keep the petrochemical industries competitive with foreign industries, so that they continue to be one of Brazil's major employers.

A utilização de perácidos na deslignificação e no branqueamento de polpas celulósicas

Peracids are strong oxidant species and their use is being largely studied in the delignification and cellulose pulp bleaching. Some of them has already an industrial application, specially in non-conventional bleaching sequences like ECF (Elemental chlorine free) and TCF (Totally chlorine free). This review presents the main aspects of the structure, properties, preparation and reaction of peracids (peracetic acid, peroxymonosulfuric acid and their mixture) with lignin, specially for peracetic acid. Information about bleaching and delignification of wood pulps with peracids and the factors affecting its efficiency are also presented.

Development of a Filter Aid Proportioning, Mixing, and Feeding System for a Polishing Filter

The purpose of this work was to study the characteristics of the most commonly used filter aid materials and their influences on the design of proportioning, mixing, and feeding system for polishing filter family. Based on the literature survey and hands-on experience a system was designed with defined equipment and capital and operating costs. The system was designed to serve precoating and bodyfeeding applications and is easily extended to be used in multiple filter processes. Also a test procedure was carried out where influences of flux and filter cloths to accumulated cake were studied. Filter aid is needed in challenging conditions to improve filtration efficiency and cleaning, and thus extend the operating life of the filter media. Filter aid preparation and feeding system was designed for the use of two different filter aids; precoat and bodyfeed. Precoating is used before the filtration step initiates. If the solids in the filterable solution have a tendency to clog the filter bag easily, precoat is used on the filter bag to obtain better filtration efficiency and quality. Diatomite or perlite is usually used as a precoating substance. The intention is to create a uniform cake to the overall surface of the filter cloth, with predetermined thickness, 2 – 5 mm. This ensures that the clogging of the filter cloth is reduced and the filtration efficiency is increased. Bodyfeed is used if the solids in the filterable solution have a tendency to form a sticky impermeable filter cake. The cake properties are enhanced by maintaining the permeability of the accumulating cake by using the filter aid substance as bodyfeed during the filtration process.