一类含裂隙岩质边坡的滑动弱化逐步破坏机理

含裂隙的岩土材料在剪切作用下,随着剪应变的增加,裂纹端部一定区域内的强度会表现出滑动弱化的现象.岩土材料这种性质的变化不同于粘性土结构性破坏,也不同于剪胀.在一定的载荷作用下,坡体内裂隙端部的滑动弱化使坡体内的应力重新分配,从而使得应力集中加剧,裂隙尖端进一步扩展,造成岩体结构性的破坏,乃至整个滑面的贯通直至发生滑坡.因此,滑动弱化是一类含裂隙岩质边坡滑坡的机理.

Effect of Rock Mass Structure and Block Size on the Slope Stability-Physical Modeling and Discrete Element Simulation

This paper studies the stability of jointed rock slopes by using our improved three-dimensional discrete element methods (DEM) and physical modeling. Results show that the DEM can simulate all failure modes of rock slopes with different joint configurations. The stress in each rock block is not homogeneous and blocks rotate in failure development. Failure modes depend on the configuration of joints. Toppling failure is observed for the slope with straight joints and sliding failure is observed for the slope with staged joints. The DEM results are also compared with those of limit equilibrium method (LEM). Without considering the joints in rock masses, the LEM predicts much higher factor of safety than physical modeling and DEM. The failure mode and factor of safety predicted by the DEM are in good agreement with laboratory tests for any jointed rock slope.

Nonlinear Analysis of Submarine Pipelines During Single Point Lifting

基于管道微单元体平衡建立了海管单点提升的非线性力学模型的控制微分方程组,使用变弧长的无量纲代换将动边界问题化为固定边界的两点边值问题,利用maple环境下编制的两点边值问题的打靶法程序得到了该问题在各个提升阶段的数值解答和在单点提升过程中管道的极限弯矩约为0.71q~{1/3}(EI)~{2/3}。

Effects of the orientation of microgravity on the concentration distribution in crystallization from solution

A quasi-steady state growth and dissolution in a 2-D rectangular enclosure is numerically investigated. This paper is an extension to indicate the effects of the orientation of gravity on the concentration field in crystallization from solution under microgravity, especially on the lateral non-uniformity of concentration distribution at the growth surface. The thermal and solute convection are included in this model.

Saturated duration for dynamic structural plastic response and fundamental periods of elastic vibration

The relationship is determined between saturated duration of rectangular pressure pulses applied to rigid, perfectly plastic structures and their fundamental periods of elastic vibration. It is shown that the ratio between the saturated duration and the fundamental period of elastic vibration of a structure is dependent upon two factors: the first one is the slenderness or thinness ratio of the structure; and the second one is the square root of ratio between the Young's elastic modulus and the yield stress of the structural material. Dimensional analysis shows that the aforementioned ratio is one of the basic similarity parameters for elastic-plastic modeling under dynamic loading.

An analysis on overall crack-number-density of short-fatigue-cracks

The evolution of dispersed short-fatigue-cracks is analysed based on the equilibrium of crack-number-density (CND). By separating the mean value and the stochastic fluctuation of local CND, the equilibrium equation of overall CND is derived. Comparing with the mean-field equilibrium equation, the equilibrium equation of overall CND has different forms in the expression of crack-nucleation-rate or crack-growth-rate. The simulation results are compared with experimental measurements showing the stochastic analyses provide consistent tendency with experiments. The discrepancy in simulation results between overall CND and mean-field CND is discussed.

喷涂于运动固壁上的模口流变流动

模口膨胀是聚合物加工中的重要现象，通常用流变效应来解释． 射流自由面上温度分布不均匀，必然会产生表面张力梯度驱动的热毛细对流．采用二维非定常有限元方法，数值模拟喷涂于运动固壁上的流变流体的模口膨胀问题．计算中考虑了流变效应和热毛细效应的耦合作用．结果表明，流变效应和热毛细效应两者均使射流截面增大，非Newton流体的流变效应是模口膨胀的主要原因．

部分重力条件下气液两相流型研究

本文分析了"和平号"空间站气液两相流实验中获得的部分重力(0.1 g和0.014 g)条件下的流型特征及其相互转换条件,并将其和常重力与微重力两相流研究中较常用的流型转换模型的预测结果进行了比较.

热轧钢板的织构

综述了热轧钢板织构的形成机制和形成特点,分析了化学成分、加热温度、终轧温度、轧制速度、轧后冷却速度以及润滑对热轧织构的影响规律,并描述了热轧织构对热轧钢板塑性应变比、屈服强度和韧性的影响特点,可为热轧钢板织构和性能的优化与控制提供依据。

The Displacement and Strain Field of Three-Dimensional Rheologic Model of Earthquake Preparation

Based on the three-dimensional elastic inclusion model proposed by Dobrovolskii, we developed a rheological inclusion model to study earthquake preparation processes. By using the Corresponding Principle in the theory of rheologic mechanics, we derived the analytic expressions of viscoelastic displacement U(r, t) , V(r, t) and W(r, t), normal strains epsilon(xx) (r, t), epsilon(yy) (r, t) and epsilon(zz) (r, t) and the bulk strain theta (r, t) at an arbitrary point (x, y, z) in three directions of X axis, Y axis and Z axis produced by a three-dimensional inclusion in the semi-infinite rheologic medium defined by the standard linear rheologic model. Subsequent to the spatial-temporal variation of bulk strain being computed on the ground produced by such a spherical rheologic inclusion, interesting results are obtained, suggesting that the bulk strain produced by a hard inclusion change with time according to three stages (alpha, beta, gamma) with different characteristics, similar to that of geodetic deformation observations, but different with the results of a soft inclusion. These theoretical results can be used to explain the characteristics of spatial-temporal evolution, patterns, quadrant-distribution of earthquake precursors, the changeability, spontaneity and complexity of short-term and imminent-term precursors. It offers a theoretical base to build physical models for earthquake precursors and to predict the earthquakes.

有二次涡的激波边界层干扰流动的DPNS和NS方程计算

针对具有二次涡复杂分离再附现象的激波边界层干扰流动，数值地考察了扩散抛物化Navier-Stokes (DPNS)方程组的适用情况。壁面摩阻和压力、主涡和二次涡的涡高和涡长、分离再附位置以及流线图等特性的计算表明：DPNS方程组的数值结果均与NS方程组的数值结果很好相符。

特征向量导数计算的简单动柔度法

在计算很多特征向量导数时, 以Nelson法为代表的直接法都显出效率低下, 第二作者为此发展了直接法的一个分支—动柔度法。本文虽是动柔度法的继续, 但就非重特征值情况而言, 它是一种最好的动柔度法, 因为它像Fox法一样, “ 一步求解”便可获得通解, 然而它又不存在Fox法的缺点—支配方程的系数阵为满阵, 所以说, 在计算很多非重特征值的特征向量导数时, 简单动柔度法不仅在计算步骤上比Nelson法简单, 而且在计算时间上成倍地减少。

Application of the Conjugate Gradient Optimization Algorithm of Neural Network on Laser Machining

在应用激光技术加工复杂曲面时,通常以采样点集为插值点来建立曲面函数,然后实现曲面上任意坐标点的精确定位。人工神经网络的BP算法能实现函数插值,但计算精度偏低,往往达不到插值精确要求,造成较大的加工误差。提出人工神经网络的共轭梯度最优化插值新算法,并通过实例仿真,证明了这种曲面精确定位方法的可行性,从而为激光加工的三维精确定位提供了一种良好解决方案。这种方法已经应用在实际中。

Preliminary Studies of Practicability of Laminar Plasma Surface Treatment Process

The basic remelting and cladding tests with laminar plasma technology on metals have been conducted in order to demonstrate the possibility of the technology applied in material surface modification. The experimental results show that the properties of the modified layers of the cast iron surface can be improved notably by the remelting treatment and those of the stainless steel by the cladding treatment. The related results are also verified by microscopic studies such as scanning electron microscopic (SEM) observations, energy dispersive spectra (EDS) analysis and the Vickers hardness measurements of the surface modified layers.

三组元W/O乳化液的表面张力和雾化特性

研究了W／O型乳化液的表面张力，压力雾化喷嘴的乳化液雾化特性与乳化液的组分、乳化剂的黏度以及喷油压力的关系．实验结果表明：乳化液的表面张力接近柴油，但喷雾滴径均大于柴油，而且喷嘴的启喷压力、乳化液组分和乳化剂黏度对乳化液平均滴径均有显著影响．随着启喷压力升高，喷雾滴径明显减小；若启喷压力相同，随着乳化液中水相含量增加(不高于50％)，乳化液喷雾滴径随之增加；采用高黏度、低HLB值乳化剂配制的乳化液的喷雾滴径相对较大；内相界面特性和界面上的乳化剂会对滴径分布有重要影响．