925 resultados para Border patrol
Resumo:
A crack intersecting an interface between two dissimilar materials may advance by either penetrating through the interface or deflecting into the interface. The competition between deflection and penetration can be assessed by comparison of two ratios: (i) the ratio of the energy release rates for interface cracking and crack penetration; and (ii) the ratio of interface to material fracture energies. Residual stresses caused by thermal expansion misfit can influence the energy release rates of both the deflected and penetrating crack. This paper analyses the role of residual stresses. The results reveal that expansion misfit can be profoundly important in systems with planar interfaces (such as layered materials, thin film structures, etc.), but generally can be expected to be of little significance in fiber composites. This paper corrects an earlier result for the ratio of the energy release rate for the doubly deflected crack to that for the penetrating crack in the absence of residual stress.
Resumo:
Near threshold, mixed mode (I and II), fatigue crack growth occurs mainly by two mechanisms, coplanar (or shear) mode and branch (or tensile) mode. For a constant ratio of ΔKI/ΔKII the shear mode growth shows a self-arrest character and it would only start again when ΔKI and ΔKII are increased. Both shear crack growth and the early stages of tensile crack growth, are of a crystallographic nature; the fatigue crack proceeds along slip planes or grain boundaries. The appearance of the fracture surfaces suggest that the mechanism of crack extension is by developing slip band microcracks which join up to form a macrocrack. This process is thought to be assisted by the nature of the plastic deformation within the reversed plastic zone where high back stresses are set up by dislocation pile-ups against grain boundaries. The interaction of the crack tip stress field with that of the dislocation pile-ups leads to the formation of slip band microcracks and subsequent crack extension. The change from shear mode to tensile mode growth probably occurs when the maximum tensile stress and the microcrack density in the maximum tensile plane direction attain critical values.
Resumo:
The first of January, 1912, E. A. Goldman, of the Biological Survey, Department of Agriculture, was again detailed on the Smithsonian Biological Survey of the Canal Zone. He returned to Panama in January and remained there until the last of June passing most of this period in collecting birds and mammals on the slopes of Mount Pirri on the Pacific side of eastern Panama, near the Colombian border...(Document contains 27 pages)
Resumo:
In 2006 the UK-based charity, Global Ocean, with local support from the Third Millennium Foundation, convened a Conversation among specialists about the problems facing the conservation of whales. Called "A consultation on whaling", this gathering was held in the ancient village of Paciano, in Umbria near the border with Tuscany, 15 – 17 October 2006. There were 15 participants from 11 countries. Dr Kees Lankester served as moderator. The outcome was an Aide Memoire which served to guide the participants in the run-up to the 2007 meeting of the International Whaling Commission (IWC), held in Anchorage, Alaska, in June. One point of agreement was that a second consultation should be held in the months following the Anchorage meeting, involving some but not necessarily all of the participants in the first, but concentrating this time on scientific issues – especially those encountered in the Scientific Committee of the IWC –with particular attention to informing a wider public about those scientific activities in relation to the problems confronting the IWC and the views of scientists about them. This document is the report of that Conversation, referred to as Paciano II. The moderator was Dr Giuseppe Notarbartolo di Sciara and the Report was written by Kieran Mulvaney in consultation with all participants, and with reference to an Aide Memoire prepared by the Rapporteur, Dr Russell Leaper. The sponsor and organisers have agreed with the general sentiment expressed by participants in Paciano II that further such conversations should be held at roughly yearly intervals and they will try to satisfy that desire. Although these future gatherings would be concerned with the living ocean they would not necessarily be restricted in future to consideration of whales and whaling. Discussions are on-going for selection of a theme which is of both scientific interest and practical concern for conservation of marine life and management of the uses of ocean space. (Document has 18 pages)
Resumo:
In 2006 the UK-based charity, Global Ocean, with local support from the Third Millennium Foundation, convened a Conversation among specialists about the problems facing the conservation of whales. Called "A consultation on whaling", this gathering was held in the ancient village of Paciano, in Umbria near the border with Tuscany, 15 – 17 October 2006. There were 15 participants from 11 countries. Dr Kees Lankester served as moderator. The outcome was an Aide Memoire which served to guide the participants in the run-up to the 2007 meeting of the International Whaling Commission (IWC), held in Anchorage, Alaska, in June. One point of agreement was that a second consultation should be held in the months following the Anchorage meeting, involving some but not necessarily all of the participants in the first, but concentrating this time on scientific issues – especially those encountered in the Scientific Committee of the IWC –with particular attention to informing a wider public about those scientific activities in relation to the problems confronting the IWC and the views of scientists about them. This document is the report of that Conversation, referred to as Paciano II. The moderator was Dr Giuseppe Notarbartolo di Sciara and the Report was written by Kieran Mulvaney in consultation with all participants, and with reference to an Aide Memoire prepared by the Rapporteur, Dr Russell Leaper. The sponsor and organisers have agreed with the general sentiment expressed by participants in Paciano II that further such conversations should be held at roughly yearly intervals and they will try to satisfy that desire. Although these future gatherings would be concerned with the living ocean they would not necessarily be restricted in future to consideration of whales and whaling. Discussions are on-going for selection of a theme which is of both scientific interest and practical concern for conservation of marine life and management of the uses of ocean space. (19 page document)
Resumo:
[ES] El proyecto estudia algoritmos de detección de bordes aplicados a imágenes fotográficas y procedentes de nubes de puntos, posteriormente combina los resultados y analiza las posibilidades de mejora de la solución conjunta.
Resumo:
Ejemplar dedicado a: Élites sociales y poder territorial.
Resumo:
Increased boating activities and new waterfront developments have contributed an estimated 3,000 dismantled, abandoned, junked, wrecked, derelict vessels to Florida coastal waters. This report outlines a method of siting and prioritizing derelict vessel removal using the Florida Keys as a test area. The data base was information on 240 vessels, obtained from Florida Marine Patrol files. Vessel location was plotted on 1:250,000 regional and 1:5,000 and 1:12,000 site maps. Type of vessel, length, hull material, engine, fuel tanks, overall condition, afloat and submerged characteristics, and accessibility, were used to derive parametric site indices of removal priority and removal difficulty. Results indicate 59 top priority cases which should be the focus of immediate clean up efforts in the Florida Keys. Half of these cases are rated low to moderate in removal difficulty; the remainder are difficult to remove. Removal difficulty is a surrogate for removal cost: low difficulty -low cost, high difficulty - high cost. The rating scheme offers coastal planners options of focusing removal operations either on (1) specific areas with clusters of high priority derelict vessels or on (2) selected targeted derelicts at various, specific locations. (PDF has 59 pages.)
The Intelligent Measuring Sub-System in the Computer Integrated and Flexible Laser Processing System
Resumo:
Based on the computer integrated and flexible laser processing system, develop the intelligent measuring sub-system. A novel model has been built to compensate the deviations of the main frame, a new-developed 3-D laser tracker system is applied to adjust the accuracy of the system. Analyzing the characteristic of all kinds of automobile dies, which is the main processing object of the laser processing system, classify the types of the surface and border needed to be measured and be processed. According to different types of surface and border, develop 2-D adaptive measuring method based on B?zier curve and 3-D adaptive measuring method based on spline curve. During the data processing, a new 3-D probe compensation method has been described in details. Some measuring experiments and laser processing experiments are carried out to testify the methods. All the methods have been applied in the computer integrated and flexible laser processing system invented by the Institute of Mechanics, CAS.
Resumo:
Pulsed laser beam was used to modify surface processing for ductile iron. The microstructures of processed specimen were observed using optical microscope (OM). Nanoindentation and micro-hardness of microstructures were measured from surface to inner of sample. The experimental results show that, modification zone is consisted of light melted zone, phase transformation hardening area and transient area. The light melt area is made up of coarse dendrite crystalline with a thickness less than 20um, phase transformation hardening area mainly of laminal or acicular martensite, retained austenite and graphite, i.e. M+A prime+ G. The cow-eye microstructure around graphite sphere always is formed in phase transformation hardening area zone, which consisting of a variety structure with the distance from the surface. So, it maybe as a obvious sign distinguishing modification zone border. Finally, the microstructures evolution of laser pulse processed ductile iron was analyzed coupling with beam energy distribution in space and laser pulse heating procession characteristics. The analysis shows that energy distribution of laser pulse has an important effect on microstructure during laser pulse modified ductile iron. Multi-scale and interlace arrangement are the important features for laser pulse modified ductile iron. Of microstructure.
Resumo:
Executive Summary: The western National Coastal Assessment (NCA-West) program of EPA, in conjunction with the NOAA National Ocean Service (NOS), conducted an assessment of the status of ecological condition of soft sediment habitats and overlying waters along the western U.S. continental shelf, between the target depths of 30 and 120 m, during June 2003. NCA-West and NOAA/NOS partnered with the West Coast states (Washington (WA), Oregon (OR), and California (CA)), and the Southern California Coastal Water Research Project (SCCWRP) Bight ’03 program to conduct the survey. A total of 257 stations were sampled from Cape Flattery, WA to the Mexican border using standard methods and indicators applied in previous coastal NCA projects. A key study feature was the incorporation of a stratified-random sampling design with stations stratified by state and National Marine Sanctuary (NMS) status. Each of the three states was represented by at least 50 random stations. There also were a total of 84 random stations located within NOAA’s five NMSs along the West Coast including the Olympic Coast NMS (OCNMS), Cordell Bank NMS (CBNMS), Gulf of Farallones NMS (GFNMS), Monterey Bay NMS (MBNMS), and Channel Islands NMS (CINMS). Collection of flatfish via hook-and-line for fish-tissue contaminant analysis was successful at 50 EMAP/NCA-West stations. Through a collaboration developed with the FRAM Division of the Northwest Fisheries Science Center, fish from an additional 63 stations in the same region and depth range were also analyzed for fish-tissue contaminants. Bottom depth throughout the region ranged from 28 m to 125 m for most stations. Two slightly deeper stations from the Southern California Bight (SCB) (131, 134 m) were included in the data set. About 44% of the survey area had sediments composed of sands (< 20% silt-clay), about 47% was composed of intermediate muddy sands (20-80% silt-clay), and about 9% was composed of muds (> 80% silt-clay). The majority of the survey area (97%) had relatively low percent total organic carbon (TOC) levels of < 2%, while a small portion (< 1%) had high TOC levels (> 5%), in a range potentially harmful to benthic fauna. Salinity of surface waters for 92% of the survey area were > 31 psu, with most stations < 31 psu associated with the Columbia River plume. Bottom salinities ranged only between 31.6 and 34.4 psu. There was virtually no difference in mean bottom salinities among states or between NMS and non-NMS stations. Temperatures of surface water (range 8.5 -19.9 °C) and bottom water (range 5.8 -14.7 °C) averaged several degrees higher in CA in comparison to WA and OR. The Δσt index of watercolumn stratification indicated that about 31% of the survey area had strong vertical stratification of the water column. The index was greatest for waters off WA and lowest for CA waters. Only about 2.6 % of the survey area had surface dissolved oxygen (DO) concentrations ≤ 4.8 mg/L, and there were no values below the lower threshold (2.3 mg/L) considered harmful to the survival and growth of marine animals. Surface DO concentrations were higher in WA and OR waters than in CA, and higher in the OC NMS than in the CA sanctuaries. An estimated 94.3% of the area had bottom-water DO concentrations ≤ 4.8 mg/L and 6.6% had concentrations ≤ 2.3 mg/L. The high prevalence of DO from 2.3 to 4.8 mg/L (85% of survey area) is believed to be associated with the upwelling of naturally low DO water across the West Coast shelf. Mean TSS and transmissivity in surface waters (excluding OR due to sample problems) were slightly higher and lower, respectively, for stations in WA than for those in CA. There was little difference in mean TSS or transmissivity between NMS and non-NMS locations. Mean transmissivity in bottom waters, though higher in comparison to surface waters, showed little difference among geographic regions or between NMS and non-NMS locations. Concentrations of nitrate + nitrite, ammonium, total dissolved inorganic nitrogen (DIN) and orthophosphate (P) in surface waters tended to be highest in CA compared to WA and OR, and higher in the CA NMS stations compared to CA non-sanctuary stations. Measurements of silicate in surface waters were limited to WA and CA (exclusive of the SCB) and showed that concentrations were similar between the two states and approximately twice as high in CA sanctuaries compared to OCNMS or nonsanctuary locations in either state. The elevated nutrient concentrations observed at CA NMS stations are consistent with the presence of strong upwelling at these sites at the time of sampling. Approximately 93% of the area had DIN/P values ≤ 16, indicative of nitrogen limitation. Mean DIN/P ratios were similar among the three states, although the mean for the OCNMS was less than half that of the CA sanctuaries or nonsanctuary locations. Concentrations of chlorophyll a in surface waters ranged from 0 to 28 μg L-1, with 50% of the area having values < 3.9 μg L-1 and 10% having values > 14.5 μg L-1. The mean concentration of chlorophyll a for CA was less than half that of WA and OR locations, and concentrations were lowest in non-sanctuary sites in CA and highest at the OCNMS. Shelf sediments throughout the survey area were relatively uncontaminated with the exception of a group of stations within the SCB. Overall, about 99% of the total survey area was rated in good condition (<5 chemicals measured above corresponding effect range low (ERL) concentrations). Only the pesticides 4,4′-DDE and total DDT exceeded corresponding effect range-median (ERM) values, all at stations in CA near Los Angeles. Ten other contaminants including seven metals (As, Cd, Cr, Cu, Hg, Ag, Zn), 2-methylnaphthalene, low molecular weight PAHs, and total PCBs exceeded corresponding ERLs. The most prevalent in terms of area were chromium (31%), arsenic (8%), 2-methylnaphthalene (6%), cadmium (5%), and mercury (4%). The chromium contamination may be related to natural background sources common to the region. The 2-methylnaphthalene exceedances were conspicuously grouped around the CINMS. The mercury exceedances were all at non-sanctuary sites in CA, particularly in the Los Angeles area. Concentrations of cadmium in fish tissues exceeded the lower end of EPA’s non-cancer, human-health-risk range at nine of 50 EMAP/NCA-West and nine of 60 FRAM groundfish-survey stations, including a total of seven NMS stations in CA and two in the OCNMS. The human-health guidelines for all other contaminants were only exceeded for total PCBs at one station located in WA near the mouth of the Columbia River. Benthic species richness was relatively high in these offshore assemblages, ranging from 19 to 190 taxa per 0.1-m2 grab and averaging 79 taxa/grab. The high species richness was reflected over large areas of the shelf and was nearly three times greater than levels observed in estuarine samples along the West Coast (e.g NCA-West estuarine mean of 26 taxa/grab). Mean species richness was highest off CA (94 taxa/grab) and lower in OR and WA (55 and 56 taxa/grab, respectively). Mean species richness was very similar between sanctuary vs. non-sanctuary stations for both the CA and OR/WA regions. Mean diversity index H′ was highest in CA (5.36) and lowest in WA (4.27). There were no major differences in mean H′ between sanctuary vs. nonsanctuary stations for both the CA and OR/WA regions. A total of 1,482 taxa (1,108 to species) and 99,135 individuals were identified region-wide. Polychaetes, crustaceans and molluscs were the dominant taxa, both by percent abundance (59%, 17%, 12% respectively) and percent species (44%, 25%, 17%, respectively). There were no major differences in the percent composition of benthic communities among states or between NMSs and corresponding non-sanctuary sites. Densities averaged 3,788 m-2, about 30% of the average density for West Coast estuaries. Mean density of benthic fauna in the present offshore survey, averaged by state, was highest in CA (4,351 m-2) and lowest in OR (2,310 m-2). Mean densities were slightly higher at NMS stations vs. non-sanctuary stations for both the CA and OR/WA regions. The 10 most abundant taxa were the polychaetes Mediomastus spp., Magelona longicornis, Spiophanes berkeleyorum, Spiophanes bombyx, Spiophanes duplex, and Prionospio jubata; the bivalve Axinopsida serricata, the ophiuroid Amphiodia urtica, the decapod Pinnixa occidentalis, and the ostracod Euphilomedes carcharodonta. Mediomastus spp. and A. serricata were the two most abundant taxa overall. Although many of these taxa have broad geographic distributions throughout the region, the same species were not ranked among the 10 most abundant taxa consistently across states. The closest similarities among states were between OR and WA. At least half of the 10 most abundant taxa in NMSs were also dominant in corresponding nonsanctuary waters. Many of the abundant benthic species have wide latitudinal distributions along the West Coast shelf, with some species ranging from southern CA into the Gulf of Alaska or even the Aleutians. Of the 39 taxa on the list of 50 most abundant taxa that could be identified to species level, 85% have been reported at least once from estuaries of CA, OR, or WA exclusive of Puget Sound. Such broad latitudinal and estuarine distributions are suggestive of wide habitat tolerances. Thirteen (1.2%) of the 1,108 identified species are nonindigenous, with another 121 species classified as cryptogenic (of uncertain origin), and 208 species unclassified with respect to potential invasiveness. Despite uncertainties of classification, the number and densities of nonindigenous species appear to be much lower on the shelf than in the estuarine ecosystems of the Pacific Coast. Spionid polychaetes and the ampharetid polychaete Anobothrus gracilis were a major component of the nonindigenous species collected on the shelf. NOAA’s five NMSs along the West Coast of the U.S. appeared to be in good ecological condition, based on the measured indicators, with no evidence of major anthropogenic impacts or unusual environmental qualities compared to nearby nonsanctuary waters. Benthic communities in sanctuaries resembled those in corresponding non-sanctuary waters, with similarly high levels of species richness and diversity and low incidence of nonindigenous species. Most oceanographic features were also similar between sanctuary and non-sanctuary locations. Exceptions (e.g., higher concentrations of some nutrients in sanctuaries along the CA coast) appeared to be attributable to natural upwelling events in the area at the time of sampling. In addition, sediments within the sanctuaries were relatively uncontaminated, with none of the samples having any measured chemical in excess of ERM values. The ERL value for chromium was exceeded in sediments at the OCNMS, but at a much lower percentage of stations (four of 30) compared to WA and OR non-sanctuary areas (31 of 70 stations). ERL values were exceeded for arsenic, cadmium, chromium, 2- methylnaphthalene, low molecular weight PAHs, total DDT, and 4,4′-DDE at multiple sites within the CINMS. However, cases where total DDT, 4,4′-DDE, and chromium exceeded the ERL values were notably less prevalent at CINMS than in non-sanctuary waters of CA. In contrast, 2-methylnaphthalene above the ERL was much more prevalent in sediments at the CINMS compared to non-sanctuary waters off the coast of CA. While there are natural background sources of PAHs from oil seeps throughout the SCB, this does not explain the higher incidence of 2-methylnaphthalene contamination around CINMS. Two stations in CINMS also had levels of TOC (> 5%) potentially harmful to benthic fauna, though none of these sites exhibited symptoms of impaired benthic condition. This study showed no major evidence of extensive biological impacts linked to measured stressors. There were only two stations, both in CA, where low numbers of benthic species, diversity, or total faunal abundance co-occurred with high sediment contamination or low DO in bottom water. Such general lack of concordance suggests that these offshore waters are currently in good condition, with the lower-end values of the various biological attributes representing parts of a normal reference range controlled by natural factors. Results of multiple linear regression, performed using full model procedures to test for effects of combined abiotic environmental factors, suggested that latitude and depth had significant influences on benthic variables regionwide. Latitude had a significant inverse influence on all three of the above benthic variables, i.e. with values increasing as latitude decreased (p< 0.01), while depth had a significant direct influence on diversity (p < 0.001) and inverse effect on density (p <0.01). None of these variables varied significantly in relation to sediment % fines (at p< 0.1), although in general there was a tendency for muddier sediments (higher % fines) to have lower species richness and diversity and higher densities than coarser sediments. Alternatively, it is possible that for some of these sites the lower values of benthic variables reflect symptoms of disturbance induced by other unmeasured stressors. The indicators in this study included measures of stressors (e.g., chemical contaminants, eutrophication) that are often associated with adverse biological impacts in shallower estuarine and inland ecosystems. However, there may be other sources of humaninduced stress in these offshore systems (e.g., bottom trawling) that pose greater risks to ambient living resources and which have not been captured. Future monitoring efforts in these offshore areas should include indicators of such alternative sources of disturbance. (137pp.) (PDF contains 167 pages)
Resumo:
ENGLISH: Yellowfin tuna, Neothunnus macropterus, and skipjack tuna, Katsuwonus pelamis, are fished intensively off the west coast of the Americas in an area from about the California-Mexico border in the north to the Peru-Chile border in the south. The historical development of this fishery, and its expansion by the long-range California fleets of bait and purse-seine vessels, are well documented by Godsil (1938), Scofield (1951) and Shimada and Sehaefer (1956). The quarterly distribution of the tuna catches within this area has been reported for some recent years by Alverson (1959). SPANISH: Los atunes aleta amarilla, Neothunnus macropterus, y barrilete, Katsuwonus pelamis, son pescados con intensidad frente a la costa occidental del continente americano, en un área comprendida más o menos entre la frontera California-México en el norte y el límite Perú-Chile en el sur. El desarrollo histórico de esta pesquería y la expansión que le han dado las flotas californianas de largo radio de acción, formadas por los barcos de carnada y rederos, están bien documentados por Godsil (1938), Scofield (1951) y Shimada y Schaefer (1956). La distribución trimestral de las pescas de atún dentro de esta área ha sido tratada por Alverson (1959) con referencia a años recientes.
Resumo:
border="0" alt="" hspace="6" width="100" height="139" align="left" /> 本书系统地介绍了微／纳米力学测试技术中最常用的压入和划入技术及其典型应用。全书共分13章。测试技术方面，内容涉及接触力学、测试原理、方法、校准、仪器、力学参量、影响因素。典型应用方面，内容涉及在表面工程、微机电系统、生物、高聚物和金属玻璃等领域内的微／纳米力学行为的测试。本书可供力学、材料、物理、电子、机械、生物和化学等领域的研究人员、工程技术人员以及大专院校相关专业的师生参考。
目录
前言
第1章 绪论
1.1硬度的定义和分类
1.2纳米压入和划入技术的发展
1.3纳米压入和划入技术的特点
参考文献
第2章 压入接触力学
2.1弹性接触
2.1.1 Soeddon解
2.1.2锥形压针
2.1.3球形压针
2.1.4圆柱压针
2.2弹塑性接触
2.2.1塑性发生
2.2.2完全塑性
2.2.3材料响应
参考文献
第3章 纳米压入测试原理
3.1压入硬度和模量
3.2连续刚度测量
3.3载荷一深度数据确定的材料参数
3.3.1马氏硬度
3.3.2压入蠕变
3.3.3压入松弛
3.3.4压入弹性功和塑性功
参考文献
第4章 纳米压入测试方法
4.1压针类型
4.1.1玻氏压针
4.1.2立方角压针
4.1.3维氏压针
4.1.4努氏压针
4.1.5圆锥压针
4.1.6球形压针
4.1.7圆柱压针
4.1.8楔形压针
4.1.9考虑因素
4.2测试环节
4.2.1样品准备
4.2.2环境控制
4.2.3间距选择
4.2.4表面探测
4.2.5驱动方式
4.2.6测试步骤
4.2.7测试报告
参考文献
第5章 纳米压入的确认和校准
5.1直接确认和校准
5.2间接校准
5.3测试和校准的实例
参考文献
第6章 纳米压入和划入的测量仪器
6.1仪器技术指标的定义
6.2美国Mrs公司
6.3美国Hysitmn公司
6.4瑞士CSM公司
6.5英国MML公司
6.6澳大利亚CSIRO公司
6.7测量仪器的发展趋势
参考文献
第7章 力学参量的测量
7.1压入方式
7.1.1硬度和模量
7.1.2断裂韧度
7.1.3蠕变和粘弹行为
7.1.4压入应力??应变曲线
7.1.5加卸载曲线涉及的
部分现象
7.2划人方式
7.2.1块体材料
7.2.2薄膜材料
7.2.3粗糙度
7.3弯曲方式
7.3.1微悬臂梁静载弯曲
7.3.2微桥静载弯曲
7.3.3微结构疲劳
7.4吸引方式
7.5声发射测试
7.6温度测试
参考文献.
第8章 影响纳米压入测试的因素
8.1测试仪器的影响
8.1.1压针缺陷
8.1.2测试方法
8.1.3接触零点的确定
8.1.4载荷和位移的分辨力
8.2样品的表面状态和性质
8.2.1表面吸湿
8.2.2表面粗糙度
8.2.3残余应力
8.2.4凹陷和凸起变形
8.3纳米压入和划入测试所面临的问题
参考文献
第9章 在表面工程中的应用
9.1金属材料表面激光强化的力学表征
9.2硬质膜的力学和摩擦学性能评估
9.2.1显微硬度测试
9.2.2纳米压人测试
9.2.3纳米划入测试
9.2.4膜材的影响
参考文献
第10章 在微机电系统中的应用
10.1薄膜测试
10.1.1典型薄膜材料的硬度和模量
10.1.2薄膜疲劳
10.1.3淀积工艺对二氧化硅薄膜力学性质的影响
10.2微结构弯曲
10.2.1微结构的静态弯曲
10.2.2微结构的动态弯曲
参考文献
第11章 在生物及其相关材料中的应用
11.1人工林杉木管胞细胞壁
11.2人体腰椎骨
11.3存储液对人体牙齿微力学性能的影响
参考文献
第12章 在高聚物中的应用
12.1PMMA单轴拉伸和弯曲力学行为
12.2划入测试的理论分析
12.3韧性行为的描述
12.4脆性行为的描述
12.4.1温度效应
12.4.2应变率效应
参考文献
第13章 在金属玻璃中的应用
13.1硬度和屈服应力的关系
13.2不连续的塑性变形
13.3压痕形貌和微结构变化
13.4应变率效应
13.5钕基金属玻璃的变形行为
参考文献
附录 常见问题的回答
1测试数量
2压入间距
3压入深度
4泊松比的选择
5典型材料的参数
6断裂韧度测试压针的选择
7纳米薄膜的测试
8典型材料的压入变形行为
9显微硬度和纳米压入硬度的关系
10压入影响区及其边界效应
10.1压入影响区的有限元模拟
10.2边界距离影响的有限元模拟
10.3压人间距影响的测试
参考文献
Resumo:
border="0" alt="" width="240" height="300" />
Resumo:
