Detecção de interface em tanques de petróleo usando transmissores de nível e controladores Fuzzy

This work presents a proposal to detect interface in atmospheric oil tanks by installing a differential pressure level transmitter to infer the oil-water interface. The main goal of this project is to maximize the quantity of free water that is delivered to the drainage line by controlling the interface. A Fuzzy Controller has been implemented by using the interface transmitter as the Process Variable. Two ladder routine was generated to perform the control. One routine was developed to calculate the error and error variation. The other was generate to develop the fuzzy controller itself. By using rules, the fuzzy controller uses these variables to set the output. The output is the position variation of the drainage valve. Although the ladder routine was implemented into an Allen Bradley PLC, Control Logix family it can be implemented into any brand of PLCs

Análise do desempenho de um queimador infravermelho funcionando com gás liquefeito de petróleo e glicerina

The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with greater control of emissions due to the passage of exhaust gases through a macro-porous ceramic bed. This paper presents an infrared burner commercial, which was adapted an experimental ejector, capable of promoting a mixture of liquefied petroleum gas (LPG) and glycerin. By varying the percentage of dual-fuel, it was evaluated the performance of the infrared burner by performing an energy balance and atmospheric emissions. It was introduced a temperature controller with thermocouple modulating two-stage (low heat / high heat), using solenoid valves for each fuel. The infrared burner has been tested and tests by varying the amount of glycerin inserted by a gravity feed system. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by a data acquisition system which recorded real-time measurements of the thermocouples attached. The burner had a stable combustion at levels of 15, 20 and 25% of adding glycerin in mass ratio of LPG gas, increasing the supply of heat to the plate. According to data obtained showed that there was an improvement in the efficiency of the 1st Law of infrared burner with increasing addition of glycerin. The emission levels of greenhouse gases produced by combustion (CO, NOx, SO2 and HC) met the environmental limits set by resolution No. 382/2006 of CONAMA

Desenvolvimento de sistemas de aditivos químicos para aplicação em cimentações de poços de petróleo

The primary cementing is an important step in the oilwell drilling process, ensuring the mechanical stability of the well and the hydraulic isolation between casing and formation. For slurries to meet the requirements for application in a certain well, some care in the project should be taken into account to obtain a cement paste with the proper composition. In most cases, it is necessary to add chemicals to the cement to modify its properties, according to the operation conditions and thus obtain slurries that can move inside the jacket providing a good displacement to the interest area. New technologies of preparation and use of chemicals and modernization of technological standards in the construction industry have resulted in the development of new chemical additives for optimizing the properties of building materials. Products such as polycarboxylate superplasticizers provide improved fluidity and cohesion of the cement grains, in addition to improving the dispersion with respect to slurries without additives. This study aimed at adapting chemical additives used in civil construction to be used use in oilwell cement slurries systems, using Portland cement CPP-Special Class as the hydraulic binder. The chemical additives classified as defoamer, dispersant, fluid loss controller and retarder were characterized by infrared absorption spectroscopy, thermogravimetric analyses and technological tests set by the API (American Petroleum Institute). These additives showed satisfactory results for its application in cement slurries systems for oil wells. The silicone-based defoamer promoted the reduction of air bubbles incorporated during the stirring of the slurries. The dispersant significantly reduced the rheological parameters of the systems studied. The tests performed with the fluid loss controller and the retarder also resulted in suitable properties for application as chemical additives in cement slurries

Controle preditivo neural aplicado à processos petroquímicos

A pesquisa tem como objetivo desenvolver uma estrutura de controle preditivo neural, com o intuito de controlar um processo de pH, caracterizado por ser um sistema SISO (Single Input - Single Output). O controle de pH é um processo de grande importância na indústria petroquímica, onde se deseja manter constante o nível de acidez de um produto ou neutralizar o afluente de uma planta de tratamento de fluidos. O processo de controle de pH exige robustez do sistema de controle, pois este processo pode ter ganho estático e dinâmica nãolineares. O controlador preditivo neural envolve duas outras teorias para o seu desenvolvimento, a primeira referente ao controle preditivo e a outra a redes neurais artificiais (RNA s). Este controlador pode ser dividido em dois blocos, um responsável pela identificação e outro pelo o cálculo do sinal de controle. Para realizar a identificação neural é utilizada uma RNA com arquitetura feedforward multicamadas com aprendizagem baseada na metodologia da Propagação Retroativa do Erro (Error Back Propagation). A partir de dados de entrada e saída da planta é iniciado o treinamento offline da rede. Dessa forma, os pesos sinápticos são ajustados e a rede está apta para representar o sistema com a máxima precisão possível. O modelo neural gerado é usado para predizer as saídas futuras do sistema, com isso o otimizador calcula uma série de ações de controle, através da minimização de uma função objetivo quadrática, fazendo com que a saída do processo siga um sinal de referência desejado. Foram desenvolvidos dois aplicativos, ambos na plataforma Builder C++, o primeiro realiza a identificação, via redes neurais e o segundo é responsável pelo controle do processo. As ferramentas aqui implementadas e aplicadas são genéricas, ambas permitem a aplicação da estrutura de controle a qualquer novo processo

Análise de um queimador infravermelho funcionando com combustível híbrido : GLP/Bio-óleo

Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner

Ambiente para avaliação de controladores fuzzy aplicados ao método de elevação artificial por bombeio centrífugo submerso

From their early days, Electrical Submergible Pumping (ESP) units have excelled in lifting much greater liquid rates than most of the other types of artificial lift and developed by good performance in wells with high BSW, in onshore and offshore environments. For all artificial lift system, the lifetime and frequency of interventions are of paramount importance, given the high costs of rigs and equipment, plus the losses coming from a halt in production. In search of a better life of the system comes the need to work with the same efficiency and security within the limits of their equipment, this implies the need for periodic adjustments, monitoring and control. How is increasing the prospect of minimizing direct human actions, these adjustments should be made increasingly via automation. The automated system not only provides a longer life, but also greater control over the production of the well. The controller is the brain of most automation systems, it is inserted the logic and strategies in the work process in order to get you to work efficiently. So great is the importance of controlling for any automation system is expected that, with better understanding of ESP system and the development of research, many controllers will be proposed for this method of artificial lift. Once a controller is proposed, it must be tested and validated before they take it as efficient and functional. The use of a producing well or a test well could favor the completion of testing, but with the serious risk that flaws in the design of the controller were to cause damage to oil well equipment, many of them expensive. Given this reality, the main objective of the present work is to present an environment for evaluation of fuzzy controllers for wells equipped with ESP system, using a computer simulator representing a virtual oil well, a software design fuzzy controllers and a PLC. The use of the proposed environment will enable a reduction in time required for testing and adjustments to the controller and evaluated a rapid diagnosis of their efficiency and effectiveness. The control algorithms are implemented in both high-level language, through the controller design software, such as specific language for programming PLCs, Ladder Diagram language.

Uso de agentes inteligentes no controle simultâneo da largura e do reforço dos cordões de solda no processo GMAW-S

Tese (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Mecânica, 2016.

Identificación de Parámetros Borrosos para el Control de Suspensión Activa mediante Enjambre de Partículas

El artículo aborda la identificación de parámetros borrosos mediante técnicas de optimización de enjambre de partículas (PSO) y su aplicación al control de un sistema de suspensión activa. En particular, se adopta un controlador de tipo Takagi-Sugeno de orden cero con partición diifusa estándar de sus antecedentes. A diferencia de trabajos previos, donde el aprendizaje se limitaba a los parámetros de escala del control, el método propuesto permite la optimización de los conjuntos borrosos de los antecedentes. La metodología propuesta se ha experimentado con éxito sobre un sistema físico de un cuarto de vehículo.

REAL TIME FUZZY CONTROLLER FOR QUADROTOR STABILITY CONTROL

In this report, we develop an intelligent adaptive neuro-fuzzy controller by using adaptive neuro fuzzy inference system (ANFIS) techniques. We begin by starting with a standard proportional-derivative (PD) controller and use the PD controller data to train the ANFIS system to develop a fuzzy controller. We then propose and validate a method to implement this control strategy on commercial off-the-shelf (COTS) hardware. An analysis is made into the choice of filters for attitude estimation. These choices are limited by the complexity of the filter and the computing ability and memory constraints of the micro-controller. Simplified Kalman filters are found to be good at estimation of attitude given the above constraints. Using model based design techniques, the models are implemented on an embedded system. This enables the deployment of fuzzy controllers on enthusiast-grade controllers. We evaluate the feasibility of the proposed control strategy in a model-in-the-loop simulation. We then propose a rapid prototyping strategy, allowing us to deploy these control algorithms on a system consisting of a combination of an ARM-based microcontroller and two Arduino-based controllers. We then use a combination of the code generation capabilities within MATLAB/Simulink in combination with multiple open-source projects in order to deploy code to an ARM CortexM4 based controller board. We also evaluate this strategy on an ARM-A8 based board, and a much less powerful Arduino based flight controller. We conclude by proving the feasibility of fuzzy controllers on Commercial-off the shelf (COTS) hardware, we also point out the limitations in the current hardware and make suggestions for hardware that we think would be better suited for memory heavy controllers.

Un sistema di domotica per il controllo energetico domestico con tecnologie open-source.

Data la sempre maggiore richiesta di fabbisogno energetico, si è sviluppata una nuova filosofia nella gestione dei consumi energetici, il DSM (demand side management), che ha lo scopo di incoraggiare il consumatore ad usare energia in modo più intelligente e coscienzioso. Questo obiettivo, unito all’accumulo di energia da fonti rinnovabili, permetterà un abbassamento dell’utilizzo dell’energia elettrica proveniente dal consumo di fonti non rinnovabili e altamente inquinanti come quelle a combustibili fossili ed una diminuzione sia del consumo energetico, sia del costo per produrre energia che dell’energia stessa. L’home automation e la domotica in ambiente domestico rappresentano un esempio di DSM. L’obiettivo di questa tesi è quello di creare un sistema di home automation utilizzando tecnologie opensource. Sono stati utilizzati device come board Arduino UNO, Raspberry Pi ed un PC con sistema operativo GNU/Linux per creare una simulazione di un sistema di home automation abbinato alla gestione di celle fotovoltaiche ed energy storaging. Il sistema permette di poter spegnere un carico energetico in base a delle particolari circostanze come, per esempio, il superamento di una certa soglia di consumo di energia elettrica. Il software utilizzato è opensource e mira a poter ottimizzare il consumo energetico secondo le proprie finalità. Il tutto a dimostrare che si può creare un sistema di home automation da abbinare con il presente e futuro delle fonti rinnovabili utilizzando tecnologie libere in modo tale da preservare privacy e security oltre che customizzazione e possibilità di adattamento a diverse circostanze. Nella progettazione del sistema è stato implementato un algoritmo per gestire varie situazioni all’interno di un ambiente domestico. La realizzazione di tale algoritmo ha prodotto ottimi risultati nella raggiungimento degli obiettivi prefissati. Il progetto di questa tesi può essere ulteriormente ampliato ed il codice è reperibile in un repository pubblico.

Sviluppo di un sistema integrato per rampe isocrone di temperatura

Lo scopo del presente lavoro è la realizzazione e l'ottimizzazione di un software che, tramite l'utilizzo di un controllo automatico Proporzionale-Integrativo-Derivativo: PID, gestisca la temperatura di un fornetto in camera a vuoto. È necessario che il sistema sia in grado di eseguire rampe regolari di temperatura di diversa pendenza scelta dall'utente, in modo che possa essere utilizzato in futuro per esperimenti di Desorbimento Termico da parte di vari materiali. La tesi è così suddivisa, nel primo capitolo sono illustrati i concetti teorici di base utilizzati nello sviluppo dei controlli automatici. Nel secondo capitolo è descritta la parte hardware: sono mostrate le diverse sezioni che compongono il fornetto e la camera a vuoto, è inoltre illustrato il cablaggio che permette l'interfaccia del forno alla scheda Arduino ed al software LabVIEW. La terza sezione è dedicata agli studi svolti per la realizzazione del sistema di controllo PID e per la sua ottimizzazione. Il quarto capitolo è invece dedicato alla descrizione del software creato per la gestione del fornetto. Nel quinto capitolo sono infine mostrati i metodi utilizzati per il calcolo delle costanti operative del PID ed i risultati sperimentali ottenuti.

Supervisão e controlo de um sistema de canais de rega. Parte I-Definição e apresentação geral

O artigo faz a apresentação geral do sistema de supervisão e controlo (SCADA) desenvolvido para as redes primária e secundária de canais do Aproveitamento Hidroagrícola de Idanha-a-Nova, já instalado e calibrado. O SCADA permite melhorar, de modo significativo, a eficiência da gestão operacional dos canais de rega controlados por montante, tipo de canais do Aproveitamento, ao fazer o controlo de caudais nas admissões principais, a supervisão dos caudais perdidos nas descargas principais e das alturas de água nas secções de maior interesse para o controlo e a segurança. Ao atuar em tempo real e à distância, ganha-se tempo, melhora-se a segurança do funcionamento dos canais, aumenta-se a qualidade das distribuições e reduzem-se as perdas operacionais de água. Para além da apresentação geral do SCADA, incluindo o centro de controlo, as comunicações e estações de campo, são também apresentados alguns dos sinópticos desenvolvidos e os controladores digitais instalados: direto para comporta, de posição de comporta e controlador de caudal para comporta.

Cloud Base Height Measurement System Based on Stereo Vision with Automatic Calibration

Clouds are important in weather prediction, climate studies and aviation safety. Important parameters include cloud height, type and cover percentage. In this paper, the recent improvements in the development of a low-cost cloud height measurement setup are described. It is based on stereo vision with consumer digital cameras. The cameras positioning is calibrated using the position of stars in the night sky. An experimental uncertainty analysis of the calibration parameters is performed. Cloud height measurement results are presented and compared with LIDAR measurements.