Swift heavy ion induced surface and microstructural evolution in metallic glass thin films

Swift heavy ion induced changes in microstructure and surface morphology of vapor deposited Fe–Ni based metallic glass thin films have been investigated by using atomic force microscopy, X-ray diffraction and transmission electron microscopy. Ion beam irradiation was carried out at room temperature with 103 MeV Au9+ beam with fluences ranging from 3 1011 to 3 1013 ions/cm2. The atomic force microscopy images were subjected to power spectral density analysis and roughness analysis using an image analysis software. Clusters were found in the image of as-deposited samples, which indicates that the film growth is dominated by the island growth mode. As-deposited films were amorphous as evidenced from X-ray diffraction; however, high resolution transmission electron microscopy measurements revealed a short range atomic order in the samples with crystallites of size around 3 nm embedded in an amorphous matrix. X-ray diffraction pattern of the as-deposited films after irradiation does not show any appreciable changes, indicating that the passage of swift heavy ions stabilizes the short range atomic ordering, or even creates further amorphization. The crystallinity of the as-deposited Fe–Ni based films was improved by thermal annealing, and diffraction results indicated that ion beam irradiation on annealed samples results in grain fragmentation. On bombarding annealed films, the surface roughness of the films decreased initially, then, at higher fluences it increased. The observed change in surface morphology of the irradiated films is attributed to the interplay between ion induced sputtering, volume diffusion and surface diffusion

Entwicklung und Validierung der Steigbildmethode zur Differenzierung von ausgewählten Lebensmitteln aus verschiedenen Anbausystemen und Verarbeitungsprozessen

Zusammenfassung (deutsch) Seit den 1980iger Jahren wächst die Bedeutung der sog. Bildschaffenden Methoden für die Bestimmung der Qualität ökologischer Produkte. Zu diesen Methoden gehört die Biokristallisation, Steigbild und Rundfilter-Chromatographie. Die Ergebnisse dieser Methoden sind Bilder, die anhand definierter Kriterien ausgewertet werden. Bei der Biokristallisation sind es mehr oder weniger geordnete Kristallisationen auf einer Glasplatte, bei dem Steigbild zweidimensionale Strukturen auf Chromatographiepapier. In der Vergangenheit wurden die Bilder von Spezialisten ausgewertet, die nach einer längeren Schulung produktspezifische Kriterien entwickelt hatten. Im Gegensatz zur Dünnschicht-Chromatographie, wo der einzelne Stoff von der Matrix separiert wird, ist das Ziel beim Steigbild, Strukturen der möglichst ganzen Probe zu erzeugen. Die Methode wurde von Kolisko in den 1929iger Jahren entwickelt, wobei eine Kombination aus Chromatographieprozess und Metallkomplexreaktionen genutzt wurde. Die Firma WALA entwickelte die Methode für die Kontrolle ihrer Produkte und setze Silbernitrat und Eisensulfat ein. Bisher wurde die Methode qualitativ beschreibend ausgewertet, wobei einzelne Bildelemente und deren Interaktion beschrieben wurden. Deshalb musste für die vorliegende Arbeit Auswertungsmethoden entwickelt werden, mit denen auch eine statistische Bearbeitung der Ergebnisse möglich ist (nominale Unterscheidung von proben anhand der Bilder). Die Methode wurde bisher in einer Reihe von Studien eingesetzt (u.a. die Unterscheidung von Produktionsweisen). Obwohl die Bilder nur qualitativ ausgewertet wurden, konnten geschulte Prüfpersonen Proben aus verschiedenen Anbausystemen anhand der Bilder trennen. Die Ergebnisse wurden aber nicht so dokumentiert, dass sie den Erfordernissen internationaler Standardnormen für Laboratorien genügten. Deshalb mussten für diese Arbeit zunächst die Prozeduren dokumentiert und eine systematische Untersuchung zu den Einflussgrößen durchgeführt werden. Dazu wurde die visuelle Bildauswertung entwickelt und standardisiert. Die visuelle Bildauswertung basiert auf morphologischen Kriterien der Bilder von den untersuchten Weizen- und Möhrenproben. Ein Panel aus geschulten Personen entwickelte dann die Kriterien und legte sie anhand von Referenzbildern fest. Die Bilder der vorliegenden Arbeit wurden mit der einfach beschreibenden Prüfung ausgewertet, wie sie aus der sensorischen Prüfung von Lebensmitteln übernommen werden konnte. Mit geschulten und ungeschulten Prüfpersonen wurden Weizenproben und verschiedene Möhrensäfte mit der sog. Dreiecksprüfung ausgewertet (von ISO 4120). Alle Laborprozeduren wurden dokumentiert. Mit der Anwendung dieser Prozeduren wurden Vergleichsversuche mit Laboren in Dänemark und Holland (BRAD, LBI) durchgeführt. Die Ergebnisse waren sowohl für Weizen- als auch für Möhrenproben vergleichbar, wobei alle drei Labore zwischen jeweils zwei Proben unterscheiden konnten. Die systematische Untersuchung zu den Einflussgrößen zeigte, dass das Unterscheidungsvermögen der Methode vor allem von den klimatischen Bedingungen während der Steigphasen beeinflusst wird. Auch die Präkonditionierung der Papiere hat einen großen Einfluss, während die Wasserqualität (ultra-filtriert, de-ionisiert, destilliert) eine untergeordnete Bedeutung hat. Für Weizen- und Möhrenproben wurde sowohl die Wiederholbarkeit als auch die Reproduzierbarkeit getestet. Die Unterschiede in den Bildern der verschiedenen Proben waren dabei immer größer als die Variation durch Proben- und Bildwiederholung und das Labor. Die so charakterisierte Methode wurde auf kodierte Proben von definierten Feldversuchen und auf Marktproben (Paarvergleich von Anbausystemen ökologisch und konventionell) angewandt, wobei als Ergebnis mehr als 90% der Proben mit der einfach beschreibenden Prüfung anhand der Bilder unterschieden werden konnten. Die Auswertung mit der Dreiecksprüfung zeigte, dass sowohl Sorten und Verarbeitungsschritte (Saft) als auch Anbauweisen signifikant getrennt wurden. Darüber hinaus wurde die Methode auch erfolgreich auf Apfelproben angewandt. Weitere Untersuchungen müssen zeigen, ob sich das Potential der Methode, verschiedene Fragen wie die Authentizitätsprüfung von Lebensmitteln verifizieren lassen.

Impacto de una intervención de precauciones de contacto sobre la infección intrahospitalaria en una unidad neonatal

Introducción : las infecciones intrahospitalarias llevan alta morbilidad y mortalidad en pacientes críticamente enfermos en unidades neonatales. Materiales y métodos : después de un período de observación de 5 meses, se realizó una intervención educativa en una unidad neonatal de referencia en Bogotá sobre adecuadas técnicas de aislamiento y precauciones de contacto, basados en la toma de cultivos de piel para evaluar la colonización microbiológica. Se evaluó la tasa de infecciones intrahospitalarias (IIH) de los dos períodos y se realizó un ajuste teniendo en cuenta variables confusoras que afectan el riesgo de infección intrahospitalaria a través de un modelo de regresión logística incondicional. Resultados : se evaluaron 450 neonatos. 78 pacientes tuvieron IIH, siendo mayor en el primer grupo (45 de 247; 18,2%), que en el de intervención educativa: (33 de 203; 16,2%). La IIH se presentó en 17 de 25 pacientes colonizados (66,7%), 15 de 44 pacientes no colonizados (34%) y uno de los 134 pacientes a los que no se les tomó muestra (0,75%; p<0,01). El modelo mostró que el riesgo de IIH fue mayor en el grupo no intervenido, (O.R. 1,99, I.C. 95%: 1,39-12,30); otros factores de riesgo identificados fueron el uso de nutrición parenteral, la presencia de cardiopatía congénita y una mayor estancia hospitalaria. Discusión : una intervención educativa sobre adecuadas técnicas de aislamiento y precauciones de contacto en neonatos, basados en la toma de cultivos de piel para evaluar la colonización microbiológica, se asoció con una menor tasa de IIH en el grupo intervenido en una UCIN.

Infectious aspects and the etiopathogenesis of rheumatoid arthritis

Infections are believed to contribute to the maturation of the immune system from the innate to the adaptive phases and therefore may take part in the induction of autoimmune conditions. In the current study, we present an extensive analysis conducted on sera samples of patients with rheumatoid arthritis in order to seek evidence of previous or coexisting infectious processes using the Bio-Rad BioPlex immunoassay analyzer. We detected higher rates of serological evidence of infections with Epstein–Barr virus and cytomegalovirus viruses. Our findings may indicate a role of these viruses in the pathogenesis of RA.

Eliminación de compuestos causantes de olores mediante adsorbentes/catalizadores obtenidos a partir de lodos de depuradora

El aumento de la cantidad de lodos y las dificultades inherentes a su aplicación agrícola y/o disposición en vertederos, hace necesario encontrar nuevas alternativas para su gestión. A nivel europeo, hoy en día se tiende hacia la aplicación de tratamientos térmicos (incineración, pirólisis y gasificación) que permiten una valoración energética de los lodos, si bien generan un residuo sólido que sigue siendo necesario gestionar. El problema medioambiental provocado por (malos) olores resulta difícil de abordar de una manera genérica, teniendo en consideración la propia naturaleza del olor y sus posibles causas. Los olores en las EDARs son provocados básicamente por la degradación de la materia orgánica en condiciones anaeróbicas y se detectan en todas las operaciones unitarias en diferentes niveles de concentración. Esta tesis incidiendo en ambos aspectos, tiene por objeto investigar la valorización de lodos como materiales precursores de adsorbentes/ catalizadores para la eliminación de olores en el entorno de las EDARs, maximizando la reutilización de los lodos. Para la realización de los experimentos se han seleccionado lodos procedentes de tres EDARs situadas en la región de Girona (SC, SB, SL) que difieren en cuanto al tratamiento de los lodos. Ambas muestras han sido caracterizadas con el fin de determinar las diferencias más importantes en los lodos de partida. Los parámetros de caracterización incluyen el análisis de composición química (análisis elemental e inmediato, determinación contenido en cenizas, medida pH, DRX, FT-IR, SEM / EDX) así como análisis de superficie (adsorción de N2 y CO2). En primer lugar los lodos caracterizados han sido sometidos a diferentes tratamientos térmicos de gasificación y pirólisis y los adsorbentes/ catalizadores obtenidos se han probado como adsorbentes para la eliminación de H2S. Como consecuencia de este estudio, se ha desechado el uso de uno de lodos (SC) puesto que se obtenían resultados muy similares a (SB), a continuación el estudio se centró en el lodo de SL. Con este objetivo se han preparado 12 muestras 6 de ellas pirolizadas y 6 gasificadas en el rango de temperaturas que comprende 600-1100 ºC. Posteriormente las muestras han sido caracterizadas y se ha determinado la capacidad de eliminación (x/M) del H2S. Los resultados muestran que hemos sido capaces de obtener unos materiales que si bien, presentan un bajo desarrollo de porosidad dan lugar a valores de capacidades de eliminación elevados y comparables a carbones y materiales adsorbentes comerciales (Centaur, Sorbalit). Las elevadas eficiencias de eliminación se atribuyen básicamente a la presencia de especies catalíticamente activas tales como los óxidos mixtos de calcio y hierro determinados por DRX en las muestras tratadas térmicamente. El segundo bloque de resultados se centra la mejora de las propiedades texturales de estos materiales adsorbentes. Con este objetivo se llevaron acabo procesos de activación física con CO2 y química con H3PO4 e hidróxidos alcalinos (NaOH y KOH), que hasta el momento no se había probado con este tipo de precursores. Los resultados indican que la activación física (CO2) y química (H3PO4) no son unos buenos métodos para la obtención de adsorbentes altamente porosos con este tipo de materia prima bajo las condiciones probadas, sin embargo la activación con hidróxidos alcalinos da lugar a materiales adsorbentes con superficies específicas de hasta 1600 m2g-1. En el caso de la activación con hidróxidos, tanto el incremento de la relación agente activante/ precursor como el incremento de la temperatura producen un descenso del rendimiento, al mismo tiempo que incrementan el valor de SBET. Los materiales resultantes de la activación con hidróxidos alcalinos se han probado como adsorbentes/ catalizadores para la eliminación de H2S. Los resultados indican que un incremento del área superficial no es indicativo de un aumento de la capacidad de eliminación dada la naturaleza ácida de estos materiales obtenidos. Con el fin de contrarrestar el efecto ácido de estos materiales se han realizado los mismos ensayos añadiendo NaOH al lecho de reacción llegando a valores de x/M de hasta 450 mgg-1. Posteriormente también se han realizado ensayos de eliminación de NH3 con algunas de estas muestras, y los resultados obtenidos de x/M son del orden de carbones activados comerciales. Los materiales adsorbentes obtenidos tras la activación con hidróxidos alcalinos se convierten en materiales muy atractivos para ser utilizados como adsorbentes/ catalizadores de múltiples contaminantes (COVs, Hg...).

Teaching written language to students who are deaf or hard of hearing

This Independent Study looked into the effectiveness of the Interactive Writing program in teaching writing to students who are deaf or hard of hearing. The students' writing was assessed based on writing samples and teacher observations.

A cross-calibration of chlorine isotopic measurements and suitability of seawater as the international reference material

A collection of 24 seawaters from various worldwide locations and differing depth was culled to measure their chlorine isotopic composition (delta(37)Cl). These samples cover all the oceans and large seas: Atlantic, Pacific, Indian and Antarctic oceans, Mediterranean and Red seas. This collection includes nine seawaters from three depth profiles down to 4560 mbsl. The standard deviation (2sigma) of the delta(37)Cl of this collection is +/-0.08 parts per thousand, which is in fact as large as our precision of measurement ( +/- 0.10 parts per thousand). Thus, within error, oceanic waters seem to be an homogeneous reservoir. According to our results, any seawater could be representative of Standard Mean Ocean Chloride (SMOC) and could be used as a reference standard. An extended international cross-calibration over a large range of delta(37)Cl has been completed. For this purpose, geological fluid samples of various chemical compositions and a manufactured CH3Cl gas sample, with delta(37)Cl from about -6 parts per thousand to +6 parts per thousand have been compared. Data were collected by gas source isotope ratio mass spectrometry (IRMS) at the Paris, Reading and Utrecht laboratories and by thermal ionization mass spectrometry (TIMS) at the Leeds laboratory. Comparison of IRMS values over the range -5.3 parts per thousand to +1.4 parts per thousand plots on the Y=X line, showing a very good agreement between the three laboratories. On 11 samples, the trend line between Paris and Reading Universities is: delta(37)Cl(Reading)= (1.007 +/- 0.009)delta(37)Cl(Paris) - (0.040 +/- 0.025), with a correlation coefficient: R-2 = 0.999. TIMS values from Leeds University have been compared to IRMS values from Paris University over the range -3.0 parts per thousand to +6.0 parts per thousand. On six samples, the agreement between these two laboratories, using different techniques is good: delta(37)Cl(Leeds)=(1.052 +/- 0.038)delta(37)Cl(Paris) + (0.058 +/- 0.099), with a correlation coefficient: R-2 = 0.995. The present study completes a previous cross-calibration between the Leeds and Reading laboratories to compare TIMS and IRMS results (Anal. Chem. 72 (2000) 2261). Both studies allow a comparison of IRMS and TIMS techniques between delta(37)Cl values from -4.4 parts per thousand to +6.0 parts per thousand and show a good agreement: delta(37)Cl(TIMS)=(1.039 +/- 0.023)delta(37)Cl(IRMS)+(0.059 +/- 0.056), with a correlation coefficient: R-2 = 0.996. Our study shows that, for fluid samples, if chlorine isotopic compositions are near 0 parts per thousand, their measurements either by IRMS or TIMS will give comparable results within less than +/- 0.10 parts per thousand, while for delta(37)Cl values as far as 10 parts per thousand (either positive or negative) from SMOC, both techniques will agree within less than +/- 0.30 parts per thousand. (C) 2004 Elsevier B.V. All rights reserved.

Using aircraft measurements to determine the refractive index of Saharan dust during the DODO Experiments

Much uncertainty in the value of the imaginary part of the refractive index of mineral dust contributes to uncertainty in the radiative effect of mineral dust in the atmosphere. A synthesis of optical, chemical and physical in-situ aircraft measurements from the DODO experiments during February and August 2006 are used to calculate the refractive index mineral dust encountered over West Africa. Radiative transfer modeling and measurements of broadband shortwave irradiance at a range of altitudes are used to test and validate these calculations for a specific dust event on 23 August 2006 over Mauritania. Two techniques are used to determine the refractive index: firstly a method combining measurements of scattering, absorption, size distributions and Mie code simulations, and secondly a method using composition measured on filter samples to apportion the content of internally mixed quartz, calcite and iron oxide-clay aggregates, where the iron oxide is represented by either hematite or goethite and clay by either illite or kaolinite. The imaginary part of the refractive index at 550 nm (ni550) is found to range between 0.0001 i to 0.0046 i, and where filter samples are available, agreement between methods is found depending on mineral combination assumed. The refractive indices are also found to agree well with AERONET data where comparisons are possible. ni550 is found to vary with dust source, which is investigated with the NAME model for each case. The relationship between both size distribution and ni550 on the accumulation mode single scattering albedo at 550 nm (ω0550) are examined and size distribution is found to have no correlation to ω0550, while ni550 shows a strong linear relationship with ω0550. Radiative transfer modeling was performed with different models (Mie-derived refractive indices, but also filter sampling composition assuming both internal and external mixing). Our calculations indicate that Mie-derived values of ni550 and the externally mixed dust where the iron oxide-clay aggregate corresponds to the goethite-kaolinite combination result in the best agreement with irradiance measurements. The radiative effect of the dust is found to be very sensitive to the mineral combination (and hence refractive index) assumed, and to whether the dust is assumed to be internally or externally mixed.

Inferring population history with DIY ABC: a user-friendly approach to approximate Bayesian computation

Genetic data obtained on population samples convey information about their evolutionary history. Inference methods can extract part of this information but they require sophisticated statistical techniques that have been made available to the biologist community (through computer programs) only for simple and standard situations typically involving a small number of samples. We propose here a computer program (DIY ABC) for inference based on approximate Bayesian computation (ABC), in which scenarios can be customized by the user to fit many complex situations involving any number of populations and samples. Such scenarios involve any combination of population divergences, admixtures and population size changes. DIY ABC can be used to compare competing scenarios, estimate parameters for one or more scenarios and compute bias and precision measures for a given scenario and known values of parameters (the current version applies to unlinked microsatellite data). This article describes key methods used in the program and provides its main features. The analysis of one simulated and one real dataset, both with complex evolutionary scenarios, illustrates the main possibilities of DIY ABC.

Beta-lactoglobulin fibers under capillary flow

We describe the capillary flow behavior of gels of beta-lactoglobulin (beta-lg) containing droplets of fibrils and the shear flow alignment of beta-lg fibers in dilute aqueous solutions. Polarized optical microscopy and laser scanning confocal microscopy are used to show that capillary shear flow does not affect the fibril droplet sizes in the beta-lg gels, the system behaving in this respect as a solution of compact colloidal particles under shear flow. Small-angle X-ray scattering (SAXS) on dilute aqueous solutions indicates that the fibers can be initially aligned under capillary shear, but this alignment is lost after 18 min of shear. Transmission electron microscopy experiments on the samples studied by SAXS suggest that the loss of orientation is due to a shear-induced breakup of the swollen fibril network. Dynamic and static light scattering on dilute beta-lg fibril aqueous solutions are used to show that before shear beta-lg fibrils behave as strongly interacting semiflexible polymers, while they behave as weakly interacting rods after 18 min of capillary shear.

Wormlike micelle formation and flow alignment of a pluronic block copolymer in aqueous solution

The self-assembly into wormlike micelles of a poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide) triblock copolymer Pluronic P84 in aqueous salt solution (2 M NaCl) has been studied by rheology, small-angle X-ray and neutron scattering (SAXS/SANS), and light scattering. Measurements of the flow curves by controlled stress rheometry indicated phase separation under flow. SAXS on solutions subjected to capillary flow showed alignment of micelles at intermediate shear rates, although loss of alignment was observed for high shear rates. For dilute solutions, SAXS and static light scattering data on unaligned samples could be superposed over three decades in scattering vector, providing unique information on the wormlike micelle structure over several length scales. SANS data provided information on even shorter length scales, in particular, concerning "blob" scattering from the micelle corona. The data could be modeled based on a system of semiflexible self-avoiding cylinders with a circular cross-section, as described by the wormlike chain model with excluded volume interactions. The micelle structure was compared at two temperatures close to the cloud point (47 degrees C). The micellar radius was found not to vary with temperature in this region, although the contour length increased with increasing temperature, whereas the Kuhn length decreased. These variations result in an increase of the low-concentration radius of gyration with increasing temperature. This was consistent with dynamic light scattering results, and, applying theoretical results from the literature, this is in agreement with an increase in endcap energy due to changes in hydration of the poly(ethylene oxide) blocks as the temperature is increased.

What do we mean when we refer to Bacteroidetes populations in the human gastrointestinal microbiota?

Recent large-scale cloning studies have shown that the ratio of Bacteroidetes to Firmicutes may be important in the obesity-associated gut microbiota, but the species these phyla represent in this ecosystem has not been examined. The Bacteroidetes data from the recent Turnbaugh study were examined to determine those members of the phylum detected in human faecal samples. In addition, FISH analysis was performed on faecal samples from 17 healthy, nonobese donors using probe Bac303, routinely used by gut microbiologists to enumerate BacteroidesPrevotella populations in faecal samples, and another probe (CFB286) whose target range has some overlap with that of Bac303. Sequence analysis of the Turnbaugh data showed that 23/519 clones were chimeras or erroneous sequences; all good sequences were related to species of the order Bacteroidales, but no one species was present in all donors. FISH analysis demonstrated that approximately one-quarter of the healthy, nonobese donors harboured high numbers of Bacteroidales not detected by probe Bac303. It is clear that Bacteroidales populations in human faecal samples have been underestimated in FISH-based studies. New probes and complementary primer sets should be designed to examine numerical and compositional changes in the Bacteroidales during dietary interventions and in studies of the obesity-associated microbiota in humans and animal model systems.

Children's representation of family mealtime in the context of maternal eating disorders

Background Recent research provides evidence for specific disturbance in feeding and growth in children of mothers with eating disorders. Aim To investigate the impact of maternal eating disorders during the post-natal year on the internal world of children, as expressed in children's representations of self and their mother in pretend mealtime play at 5 years of age. Methods Children of mothers with eating disorders (n = 33) and a comparison group (n = 24) were videotaped enacting a family mealtime in pretend play. Specific classes of children's play representations were coded blind to group membership. Univariate analyses compared the groups on representations of mother and self. Logistic regression explored factors predicting pretend play representations. Results Positive representations of the mother expressed as feeding, eating or body shape themes were more frequent in the index group. There were no other significant group differences in representations. In a logistic regression analysis, current maternal eating psychopathology was the principal predictor of these positive maternal representations. Marital criticism was associated with negative representations of the mother. Conclusions These findings suggest that maternal eating disorders may influence the development of a child's internal world, such that they are more preoccupied with maternal eating concerns. However, more extensive research on larger samples is required to replicate these preliminary findings.

Fibrillisation of hydrophobically modified amyloid peptide fragments in an organic solvent

The self-assembly of a hydrophobically modified fragment of the amyloid beta(A beta) peptide has been studied in methanol. The peptide FFKLVFF is based on A beta(16-20) extended at the N terminus by two phenylalanine residues. The formation of amyloid-type fibrils is confirmed by Congo Red staining, thioflavin T fluorescence and circular dichroism experiments. FTIR points to the formation of beta-sheet structures in solution and in dried films and suggests that aggregation occurs at low concentration and is not strongly affected by further increase in concentration, i.e. the peptide is a strong fibril-former in methanol. UV fluorescence experiments on unstained peptide and CD point to the importance of aromatic interactions between phenylalanine groups in driving aggregation into beta-sheets. The CD spectrum differs from that usually observed for beta-sheet assemblies formed by larger peptides or proteins and this is discussed for solutions in methanol and also trifluoroethanol. The fibril structure is imaged by transmission electron microscopy and scanning electron microscopy on dried samples and is confirmed by small-angle X-ray scattering experiments in solution.

Rheology of magmas with bimodal crystal size and shape distributions: insights from analog experiments

Magmas in volcanic conduits commonly contain microlites in association with preexisting phenocrysts, as often indicated by volcanic rock textures. In this study, we present two different experiments that inves- tigate the flow behavior of these bidisperse systems. In the first experiments, rotational rheometric methods are used to determine the rheology of monodisperse and polydisperse suspensions consisting of smaller, prolate particles (microlites) and larger, equant particles (phenocrysts) in a bubble‐free Newtonian liquid (silicate melt). Our data show that increasing the relative proportion of prolate microlites to equant pheno- crysts in a magma at constant total particle content can increase the relative viscosity by up to three orders of magnitude. Consequently, the rheological effect of particles in magmas cannot be modeled by assuming a monodisperse population of particles. We propose a new model that uses interpolated parameters based on the relative proportions of small and large particles and produces a considerably improved fit to the data than earlier models. In a second series of experiments we investigate the textures produced by shearing bimodal suspensions in gradually solidifying epoxy resin in a concentric cylinder setup. The resulting textures show the prolate particles are aligned with the flow lines and spherical particles are found in well‐organized strings, with sphere‐depleted shear bands in high‐shear regions. These observations may explain the measured variation in the shear thinning and yield stress behavior with increasing solid fraction and particle aspect ratio. The implications for magma flow are discussed, and rheological results and tex- tural observations are compared with observations on natural samples.