Study of polycyclic aromatic hydrocarbons emissions from burning of local wood species in Australia

Four kinds of Australian local wood species were burned in a domestic wood heater installed in a laboratory. The selected wood species include pine, red gum, yellow box and sugar gum, that are the most popular domestic fuel wood in Australia. Particulate matter emissions from burning of each load of wood were sampled isokinetically on filter media from the flue by standard stack emission sampling train. The particle laden filters then went for Gas Chromatography/ Mass Spectrometer (GC/MS) analysis to determine polycyclic aromatic hydrocarbons (PAHs) concentrations. The sampling was conducted under two different burning conditions – air inlet of the combustion chamber fully open and half open. Approximately 15 types of PAHs were detected. Emission factors were derived as microgram of PAHs /kg of wood burned. Total particulate emission factors were also obtained from gravimetric measurement before and after the sampling. PAH emission profiles for four species were generated from the results. Comparisons of emission factors have been conducted among different species of wood, as well as under different burning conditions, ie. fast burning and slowing burning. According to the derived emission factors, pine displayed the highest level of PAHs among the four species, followed by red gum and yellow box, whereas sugar gum showed the lowest level of PAHs. Emission factors were compared between each type of wood under two different burning conditions, the slow burning condition, which was air inlet half open, clearly showed higher PAH levels compared to the fast burning condition. Total PAH fractions on particulate matter were calculated and compared among wood types under two burning conditions. During the fast burning condition, red gum and pine have the higher percentage of PAH to total particulate matter emission than sugar gum and yellow box. When changed to slow burning, the PAH fraction on particulate matter are all increased with sugar gum having the largest increase.

Baseline assessment of metals and hydrocarbons in the sediments of Lake Mulwala, Australia

An assessment of hydrocarbon and metal/metalloids (arsenic, cadmium, copper, lead, mercury, selenium, zinc) contamination in sediments from Lake Mulwala, Australia, was undertaken. The objectives of the study were: (i) to determine the extent of contamination in the lake sediments, compared to Australian and international sediment quality guidelines, and (ii) to attempt to identify the contaminant sources to the lake. With the exception of a few samples containing elevated levels of arsenic and/or mercury, the levels of all contaminants in the sediment samples taken from the lake were below the 'lower trigger' of the Australian Sediment Quality Guidelines that would warrant further investigation. High molecular weight hydrocarbons (up to 700 mg kg−1) were found in most sediment samples. Non-metric statistical analysis indicated that the contaminant distribution was different in different parts of the lake, with the lowest concentrations generally found at the influent to the lake. No definitive source(s) of contamination could be identified for either metalloids or hydrocarbons.

Photodegradation, interaction with iron oxides and bioavailability of dissolved organic matter from forested floodplain sources

Photochemical degradation of dissolved organic matter (DOM) can influence food webs by altering the availability of carbon to microbial communities, and may be particularly important following periods of high DOM input (e.g. flooding of forested floodplains). Iron oxides can facilitate these reactions, but their influence on subsequent organic products is poorly understood. Degradation experiments with billabong (= oxbow lake) water and river red gum (Eucalyptus camaldulensis) leaf leachate were conducted to assess the importance of these reactions in floodplain systems. Photochemical degradation of DOM in sunlight-irradiated quartz tubes (with and without amorphous iron oxide) was studied using gas chromatography and UV-visible spectroscopy. Photochemical reactions generated gaseous products and small organic acids. Bioavailability of billabong DOM increased following irradiation, whereas that of leaf leachate was not significantly altered. Fluorescence excitation-emission spectra suggested that the humic component of billabong organic matter was particularly susceptible to degradation, and the source of DOM influenced the changes observed. The addition of amorphous iron oxide increased rates of photochemical degradation of leachate and billabong DOM. The importance of photochemical reactions to aquatic systems will depend on the source of the DOM and its starting bioavailability, whereas inputs of freshly formed iron oxides will accelerate the processes.

Re-cycling carbon dioxide into fuel-like hydrocarbons by photocatalytic process

A new approach of heterogenous photocatalysis using titanium dioxide pellets was explored. It was found to be attractive for use in photocatalytic reduction of carbon dioxide with wavelength and temperature being crucial factors. The study also proposes a kinetic modelling for the process to simulate the product-yield profile.

Surfactant-mediated biodegradation of polycyclic aromatic hydrocarbons

Polycyclic aromatic hydrocarbons (PAHs) are toxic environmental pollutants that are known or suspected carcinogens or mutagens. Bioremediation has been used as a general way to eliminate them from the contaminated sites or aquifers, but their biodegradation is rather limited due to their low bioavailability because of their sparingly soluble nature. Surfactant-mediated biodegradation is a promising alternative. The presence of surfactants can increase the solubility of PAHs and hence potentially increase their bioavailability. However, inconclusive results have been reported on the effects of surfactant on the biodegradation of PAHs. In this work, surfactant-mediated biodegradation of PAHs is reviewed.

A novel cloud-point extraction process for preconcentrating selected polycyclic aromatic hydrocarbons in aqueous solution

A novel but simple cloud-point extraction (CPE) process is developed to preconcentrate the trace of selected polycyclic aromatic hydrocarbons (PAHs) with the use of the readily biodegradable nonionic surfactant Tergitol 15-S-7 as extractant. The concentrations of PAHs, mixtures of naphthalene and phenanthrene as well as pyrene, in the spiked samples were determined with the new CPE process at ambient temperature (23 °C) followed by high performance liquid chromatography (HPLC) with fluorescence detection. More than 80% of phenanthrene and pyrene, respectively, and 96% of naphthalene initially present in the aqueous solutions with concentrations near or below their aqueous solubilities were recovered using this new CPE process. Importantly Tergitol 15-S-7 does not give any fluorometric signal to interfere with fluorescence detection of PAHs in the UV range. No special washing step is, thus, required to remove surfactant before HPLC analyses. Different experimental conditions were studied. The optimum conditions for the preconcentration and determi nation of these selected PAHs at ambient temperature have been established as the following:  (1) 3 wt % surfactant; (2) addition of 0.5 M Na2SO4; (3) 10 min for equilibration time; and (4) 3000 rpm for centrifugal speed with duration of 10 min.

Forces measured between latex spheres in aqueous electrolyte : Non-DLVO behavior and sensitivity to dissolved gas

An atomic force microscope was used to measure the forces acting between two polystyrene latex spheres in aqueous media. The results show an electrostatic repulsion at large separations which is overtaken by an attractive “hook” that pulls the two spheres into contact from a considerable range (20−400 nm), much larger than could be expected for a van der Waals attraction. The range of operation of this attraction varies from one experiment to another and is not correlated with electrolyte concentration. However, the range is found to decrease significantly when the level of dissolved gas in the water is reduced.