Investigation of gold-based catalysts for liquid phase oxidation of glucose to glucaric acid

Glucaric acid (GA) is one of the building block chemicals derived from sugar biomass with higher added value. Nowadays, GA is produced by oxidation of glucose (Glu) with either stoichiometric oxidants (HNO3), or by means of electrochemical or biochemical synthesis. However, these processes show drawbacks from either the environmental or economic viewpoint. For this reason, gold nanoparticles (Au NPs) supported on activated carbon (AC) have been studied as catalysts for the oxidation of Glu, using O2 as oxidant in the presence of a base. Using sol immobilization technique, Au NPs have been supported on AC following different experimental procedures. UV-Vis spectroscopy, XRD, TEM and TG analysis were utilized in the characterization of the catalysts. The operational conditions were optimized obtaining 24% of yield of GA, 37% to GO and 27% to byproducts in 1 h, 1000 rpm, 10 bar of O2 and Glu:Au:NaOH molar ratio of 1000:1:3000. Under such conditions, catalysts show relatively high Glu conversion (≥82%) with different GA yields. GO+GA yield is around 58-61%. Therefore, the oxidation reaction was performed at 15 min where Au/AC PVA0 reached the highest yield of GA (16%) and Au/AC PVA2.4 gave the lowest (8%). It is evident that the presence of PVA influences to a higher degree the reaction rate than the Au NPs size. Hence, the effect of different heat treatments where applied for the removal of PVA: washing with water at 60℃ or heat treatment (120-250℃) with Air/H2. Washing treatment and heat treatment at 120℃ with Air/H2 may have resulted in the mildest treatments for the removal of PVA. Finally, two different supports have been used in order to study the effect of metal-support interaction in the immobilization of Au NPs: ZrO2 and AC. Au/AC catalyst demonstrated a higher conversion of GO to GA at short reaction times (15.1% yield GA) compared to Au/ZrO2 (2.4% yield GA).

Purple bacteria for the biotechnological valorisation of agro-industrial streams

Waste management worldwide has received increasing attention from global policies in recent years. In particular, agro-industrial streams represent a global concern due to the huge volumes generated and a high number of residues, which produce an environmental and economic impact on the ecosystem. The use of biotechnological approaches to treat these streams could allow the production of desirable by-products to be reinjected into the production cycle through sustainable processes. Purple phototrophic bacteria (PPB) are targeted as microorganisms capable to reduce the pressure of agro-industrial streams on environmental issues, due to their metabolic versatility (autotrophic and/or heterotrophic growth under different conditions). This Ph.D. research project aims to assess the effectiveness of PPB cultivation for industrial streams valorisation in the applications of biogas desulfurization and microbial protein production. For these purposes, the first part of the present work is dedicated to the cultivation of purple sulfur bacteria (PSB) for biogas streams upgrading, cleaning biogas from sulfur compounds (H2S), and producing elemental sulfur (S0), potentially suitable as a slow-release fertilizer. The second part of the thesis, instead, sees the application of purple non-sulfur bacteria (PNSB) on streams rich in organics, such as molasses, generating biomass with high content of proteins and pigments, useful as supplements in animal feed. The assessment of the main metabolic mechanisms involved in the two processes is evaluated at a laboratory scale using flasks and a photobioreactor, to define the consumption of substrates and the accumulation of products both in the autotrophic (on biogas) and in heterotrophic grow (on molasses). In conclusion, the effectiveness of processes employing PPB for a sustainable valorisation of several agro-industrial streams has been proved promising, using actual residues, and coupling their treatments with the production of added-value by-products.

Smart tracking of composite parts: feasibility study and effect on mechanical behaviour

This research proposes a solution for integrating RFID - Radio Frequency Identification technology within a structure based on CFRPs - Carbon Fiber Reinforced Polymers. Therefore, the main objective is to use technology to monitor and track composite components during manufacturing and service life. The study can be divided into two macro-areas. The first portion of the research evaluates the impact of the composite materials used on transmitting the electromagnetic signal to and from the tag. RFID technology communicates through radio frequencies to to track and trace items associated with the tags. In the first instance, a feasibility study was carried out to assess using commercially available tags. Then, after evaluating different solutions, it was decided to incorporate the tags into coupons during production. The second portion of the research is focused on evaluating the impact on the composite material's resistance to tag embedding. It starts with designing tensile test specimens through the FEM model with different housing configurations. Subsequently, the best configuration was tested in the facilities of the In the Faculty of Aerospace Engineering at TU Delft, particularly in the Structure & Materials Laboratory, two tests were conducted: the first one based on ASTM D3039/D3039 - 14 - Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, the second one dividing the path to failure into failure intervals in a load-unload-reload. Both tests were accompanied by instruments such as DIC, AE, C-Scan and Optical Microscopes. The expected result of the inclusion of RFID tags in composite components is that it brings added value to the parts with which it is associated without affecting too much its mechanical properties. This comes first from the automatic identification of RFID during the production cycle and its useful life. As a result, improvements were made in the design of production facilities.

Catalytic reduction of levulinic acid derivatives to bio-fuel components

Levulinic Acid and its esters are polyfunctional molecules obtained by biomass conversion. The most investigated strategy for the valorization of LA is its hydrogenation towards fuel additives, solvents and other added-value bio-based chemicals and, in this context, heterogeneous and homogeneous catalysts are widely used. Most commonly, it is typically performed with molecular hydrogen (H2) in batch systems, with high H2 pressures and noble metal catalysts. Several works reported the batch liquid-phase hydrogenation of LA and its esters by heterogenous catalysts which contained support with Brønsted acidity in order to obtain valeric acid and its esters. Furthermore, bimetallic and monometallic systems composed by both a metal for hydrogen activation and a promoter were demonstrated to be suitable catalysts for reduction of carboxylic group. However, there were no studies in the literature reporting the hydrogenation of alkyl levulinates to 1-pentanol (1-PAO). Therefore, bimetallic and monometallic catalysts were tested for one-pot hydrogenation of methyl levulinate to 1-PAO. Re-based catalysts were investigated, this way proving the crucial role of the support for promoting the ring-opening of GVL and its consecutive reduction to valeric compounds. All the reactions were performed in neat without the need of any additional solvents. In these conditions, bimetallic Re-Ru-O/HZSM-5 afforded methyl valerate and valeric acid (VA) with a productivity of 512 mmol gmetal-1 h-1, one of the highest reported in literature to date. Rhenium can also promote the reduction of valeric acid/esters to PV through the formation of 1-pentanol and its efficient esterification/transesterification with the starting material. However, it was proved that Re-based catalysts may undergo leaching of active phase in presence of carboxylic acids, especially by working in neat with VA. Furthermore, the over-reduction of rhenium affects catalytic performance, suggesting not only that a pre-reduction step is unnecessary but also that it could be detrimental for catalyst’s activity.

Data assimilation for advanced cross-scale unstructured-grid ocean modeling.

The coastal ocean is a complex environment with extremely dynamic processes that require a high-resolution and cross-scale modeling approach in which all hydrodynamic fields and scales are considered integral parts of the overall system. In the last decade, unstructured-grid models have been used to advance in seamless modeling between scales. On the other hand, the data assimilation methodologies to improve the unstructured-grid models in the coastal seas have been developed only recently and need significant advancements. Here, we link the unstructured-grid ocean modeling to the variational data assimilation methods. In particular, we show results from the modeling system SANIFS based on SHYFEM fully-baroclinic unstructured-grid model interfaced with OceanVar, a state-of-art variational data assimilation scheme adopted for several systems based on a structured grid. OceanVar implements a 3DVar DA scheme. The combination of three linear operators models the background error covariance matrix. The vertical part is represented using multivariate EOFs for temperature, salinity, and sea level anomaly. The horizontal part is assumed to be Gaussian isotropic and is modeled using a first-order recursive filter algorithm designed for structured and regular grids. Here we introduced a novel recursive filter algorithm for unstructured grids. A local hydrostatic adjustment scheme models the rapidly evolving part of the background error covariance. We designed two data assimilation experiments using SANIFS implementation interfaced with OceanVar over the period 2017-2018, one with only temperature and salinity assimilation by Argo profiles and the second also including sea level anomaly. The results showed a successful implementation of the approach and the added value of the assimilation for the active tracer fields. While looking at the broad basin, no significant improvements are highlighted for the sea level, requiring future investigations. Furthermore, a Machine Learning methodology based on an LSTM network has been used to predict the model SST increments.

Influence of cultivar choice, sowing date and abiotic stresses on tocopherol content and composition in Camelina sativa (L.) Crantz

In Europe, the current demand for vegetable oils and the need to find alternative crops for the regions most affected by climate change (i.e., Mediterranean basin) may be a launchpad for camelina [Camelina sativa (L.) Crantz] to be steadily introduced in European cropping systems. Camelina is mainly known for the unique composition of its oil, with a fatty acids profile including more than 50% content of essential linoleic and linolenic fatty acids, and a high tocopherol content. Being tocopherols part of the vitamin E family of antioxidants, the added value of growing camelina in harsh environments could be the enhancement of tocopherol content in camelina oil, thus having a more stable and nutritionally valuable product. With the final purpose of fully valorize camelina as a tolerant, valuable-oil producing crop for the Mediterranean basin, the main aim of this study was to investigate whether and how sowing date, cultivar choice, and abiotic stresses can affect tocopherol content and composition in camelina oil. The results showed that cultivar choice and growing conditions influenced total tocopherol, γ-tocopherol, and α-tocopherol contents. Moreover, heat stress trial revealed that high temperature increased α-tocopherol content, while no effect was observed in total tocopherols and in γ-tocopherol content. Finally, drought increased total tocopherols in camelina, and in drought-sensitive lines an increase in α-tocopherol was observed. This study allowed to acquire awareness on camelina resistance to abiotic stresses, coupled with a better knowledge on tocopherol content and composition in relation to cultivar, sowing date, and abiotic stresses. This will have an impact for the introduction of camelina as an alternative crop in harsher environments, such as the Mediterranean basin, to produce an oil suitable for food, feed, and industrial applications.

La nuova eGovernance sanitaria europea: verso una piena integrazione della digitalizzazione nei sistemi sanitari degli Stati membri

L’elaborato approfondisce il diritto alla salute nell’ordinamento dell’Unione europea, con la consapevolezza che il settore della sanità, nella complessità di una tensione perdurante tra la sua matrice sociale e l’applicazione di logiche europee di mercato, rappresenta un ambito da sempre sottratto all’intervento diretto e vincolante delle istituzioni. Contemporaneamente, prende spunto dall’osservazione della transizione digitale dei sistemi sanitari nazionali per proporre una rilettura dei tradizionali equilibri istituzionali tra ordinamenti e constatare il grado di influenza dell’Unione oltre la dimensione transfrontaliera. Infatti, per le attuali esigenze di sostenibilità dei sistemi di tutela della salute e per il valore aggiunto riconosciuto alle azioni europee nel corso della gestione della pandemia da Covid-19, l’eHealth ha rappresentato l’occasione per una vigorosa intrusione delle istituzioni europee entro prerogative tipicamente statuali, fino all’emersione di una eGovernance sanitaria europea. Pertanto, la trattazione compie un percorso evolutivo che muove dalla Direttiva 2011/24 sull’assistenza transfrontaliera e l’assistenza sanitaria online, in combinato disposto con il complesso degli atti di soft law connessi, per verificarne l’esiguo impatto sui sistemi sanitari degli Stati membri e, alla luce dei recenti investimenti strategici ed interventi normativi rilevanti in tema di tecnologie applicate alla sanità, riconoscerne il sostanziale superamento. In particolare, il confronto tra l’insufficiente livello di digitalizzazione raggiunto finora nei sistemi sanitari degli Stati membri ed il tenore della Proposta di regolamento sullo European Health Data Space suggerisce l’evoluzione dell’impianto di governo dei dati sanitari stabilito nella Direttiva, a partire dalla previsione di una disciplina comune sulla cartella sanitaria. A questo proposito, l’interoperabilità tra tecnologie diviene un presupposto operativo indefettibile, che corrobora la natura ‘tecnologicamente condizionata’ del diritto alla salute e propone l’idea che la sanità digitale rappresenti un passo in avanti verso un’assistenza europea uniforme.

Avaliação da performance empresarial: o economic value added (EVA®) e a sua relação com o valor da empresa

Mestrado em Contabilidade e Gestão das Instituições Financeiras

Criação de valor - O Cash Value Added como métrica de avaliação da Performance empresarial

Mestrado em Contabilidade e Gestão das Instituições Financeiras

Regional value added in Italy over the long run (1891-2001): linking indirect estimates with official figures, and implications

This paper presents value added estimates for the Italian regions, in benchmark years from 1891 until 1951, which are linked to those from official figures available from 1971 in order to offer a long-term picture. Sources and methodology are documented and discussed, whilst regional activity rates and productivity are also presented and compared. Thus some questions are briefly reconsidered: the origins and extent of the north-south divide, the role of migration and regional policy in shaping the pattern of regional inequality, the importance of social capital, and the positioning of Italy in the international debate on regional convergence, where it stands out for the long run persistence of its disparities.

Estimating Gross Value Added (GVA) across multiple scales: theoretical approach and empirical validation

This paper presents an application of the Multi-Scale Integrated Analysis of Societal and Ecosystem Metabolism (MuSIASEM) approach to the estimation of quantities of Gross Value Added (GVA) referring to economic entities defined at different scales of study. The method first estimates benchmark values of the pace of GVA generation per hour of labour across economic sectors. These values are estimated as intensive variables –e.g. €/hour– by dividing the various sectorial GVA of the country (expressed in € per year) by the hours of paid work in that same sector per year. This assessment is obtained using data referring to national statistics (top down information referring to the national level). Then, the approach uses bottom-up information (the number of hours of paid work in the various economic sectors of an economic entity –e.g. a city or a province– operating within the country) to estimate the amount of GVA produced by that entity. This estimate is obtained by multiplying the number of hours of work in each sector in the economic entity by the benchmark value of GVA generation per hour of work of that particular sector (national average). This method is applied and tested on two different socio-economic systems: (i) Catalonia (considered level n) and Barcelona (considered level n-1); and (ii) the region of Lima (considered level n) and Lima Metropolitan Area (considered level n-1). In both cases, the GVA per year of the local economic entity –Barcelona and Lima Metropolitan Area – is estimated and the resulting value is compared with GVA data provided by statistical offices. The empirical analysis seems to validate the approach, even though the case of Lima Metropolitan Area indicates a need for additional care when dealing with the estimate of GVA in primary sectors (agriculture and mining).

Added prognostic value of myocardial blood flow quantitation in rubidium-82 positron emission tomography imaging

Les maladies cardiovasculaires restent la cause de mortalité la plus élevée dans le monde occidental. Il s'agit d'un processus long et complexe, dont l'infarctus du myocarde et la mort cardiaque ne sont que la fin d'un spectrum. La perfusion myocardique joue un rôle central dans l'évolution de la maladie et survient chronologiquement en amont de la dysfonction diastolique et systolique, ainsi que de l'infarctus du myocarde. Une meilleure compréhension de la Physiopathologie sous-jacente est cruciale dans le diagnostique et la prise en charge du patient. Dans ce sens, ce travail tente d'évaluer l'apport de l'évaluation de la perfusion myocardique évaluée par la tomographic à émission de positron (PET/CT) quant à la prédiction d'événements cardiovasculaires. De plus, l'apport de l'évaluation quantitative par rapport à l'évaluation qualitative a été démontré dans ce travail. Nous avons utilisé un radiotraceur unique au regard de ses caractéristiques. En effet, Le Rubidium-82 est un traceur qui ne nécessite pas d'un cyclotron pour sa fabrication, dès lors qu'il est produit par un générateur, rendant ainsi sa disponibilité un atout et un avantage potentiel lors de futurs implémentations à plus grande échelle. Ce travail démontre la supériorité de l'analyse de perfusion myocardique quantitative par rapport à l'analyse traditionnelle qualitative, ce qui n'était pas encore confirmé avec le Rubidium-82. Les résultats montrent une démarcation significative entre les différentes valeurs de perfusion quantitative/absolue, permettant de distinguer différentes populations plus ou moins à risque en terme de prédiction d'événements cardiaques futurs. Il est intéressant de noter que dans un modèle combinant l'analyse qualitative et quantitative proposé dans ce travail, l'inclusion des résultats les plus ischémiques obtenus par l'analyse qualitative avec les résultats de perfusion les plus bas en terme de flux myocardique absolu (analyse quantitative) démarque une population à très bas risque d'événements cardiovasculaires majeurs, une prédiction pouvant être observée surplus de 1'000 jours. Ces résultats forment un ajout significatif quant à l'évaluation de la perfusion myocardique par la médecine nucléaire, notamment par ce model intégratif proposé, lequel permet une prédiction précise et contributive dans le cadre de futurs événements cardiovasculaires majeurs.

Value added logistical support service. Part 1 : Trends and new concept model

The aim of `Valssi' study was to find out the service requirements in `business-to-business' (B2B) markets and to present a new logistics service concept, where the traditional logistics service is expanded with significant manufacturing and value addedfacilities. The traditional third-party logistics service providers are not necessarily able to offer services, which cover widely the needs of potential customers. The study has been outlined to spare part markets in metal industry. In the second phase of the Valssi-project the aim is to examine the economical conditions and potentiality of the new logistics business concept. This research report (Part 1) concentrates on examining current trends in global and domestic logistics markets. Based on detailed survey among the participating companies, the study presents basis for a new logistics business concept model. The developed concept consists of 12 different service modules, which are split into deeper details of processes. The integration of worldwide supplier and service provider network together with customer companies systems is a challenge. The report focuses on evaluating the requirements for the new business concept from the customer-companies point of view. The study paints an overall picture of distribution and service provider network including an abstract about the software and system integration possibilities. As a result of the survey, it can be concluded that thereis need for the new business concept among the participating companies, and a modular service concept meets the requirements of them, because the new sophisticated concept considers the specialities involved in spare part logistics in metal industry.