Nonmetallic inclusion modification and its effect on the final properties of a linepipe steel

Five linepipe type steels were produced in order to study the effect of calcium and magnesium injection on their final properties. Two of these steels were at the extremes of the sulphide range i.e. 0.003 and 0.017% sulphur with no injection attempted; thereby, providing standards to compare with the injected steels. The oxygen level varied from 21 to 63 p.p.m. The cast ingots were controlled-rolled and isothermally rolled in order to study the deformation characteristics of the residual non-metallic inclusions. The structure and cleanliness of these steels was evaluated metallographically using the light microscope, SEM, and image analysis and the results related to their Charpy toughness and HIC resistance. Increasing sulphur levels decreased final properties of the steel. In the untreated state, with as little as 0.003% sulphur, test orientation was highly influential. Modification of sulphur bearing steels was achieved with low modifying element to sulphur ratios provided that the oxygen content was very low. Injection of calcium into steel caused interaction with oxide and sulphide inclusions which was biased toward oxide reduction relative to sulphur removal. Magnesium again reduced oxides and appeared to be linked with aluminia containing inclusions in the final product. It produced improved toughness values relative to a similar sulphur containing calcium treated steel. The results of this work could be extended to establish the mechanism of inclusion modification with magnesium additions to sulphur bearing steels.

Study of EEPN mitigation using modified RF pilot and Viterbi-Viterbi based phase noise compensation

We propose - as a modification of the optical (RF) pilot scheme -a balanced phase modulation between two polarizations of the optical signal in order to generate correlated equalization enhanced phase noise (EEPN) contributions in the two polarizations. The method is applicable for n-level PSK system. The EEPN can be compensated, the carrier phase extracted and the nPSK signal regenerated by complex conjugation and multiplication in the receiver. The method is tested by system simulations in a single channel QPSK system at 56 Gb/s system rate. It is found that the conjugation and multiplication scheme in the Rx can mitigate the EEPN to within 1/2 orders of magnitude. Results are compared to using the Viterbi-Viterbi algorithm to mitigate the EEPN. The latter method improves the sensitivity more than two orders of magnitude. Important novel insight into the statistical properties of EEPN is identified and discussed in the paper. © 2013 Optical Society of America.

Influence of La-doping on phase transformation and photocatalytic properties of ZnTiO3 nanoparticles synthesized via modified sol-gel method

Non-doped and La-doped ZnTiO3 nanoparticles were successfully synthesized via a modified sol–gel method. The synthesized nanoparticles were structurally characterized by PXRD, UV-vis DRS, FT-IR, SEM-EDS, TEM, Raman and photoluminescence spectroscopy. The results show that doping of La into the framework of ZnTiO3 has a strong influence on the physico-chemical properties of the synthesized nanoparticles. XRD results clearly show that the non-doped ZnTiO3 exhibits a hexagonal phase at 800 °C, whereas the La-doped ZnTiO3 exhibits a cubic phase under similar experimental conditions. In spite of the fact that it has a large ionic radius, the La is efficiently involved in the evolution process by blocking the crystal growth and the cubic to hexagonal transformation in ZnTiO3. Interestingly the absorption edge of the La-doped ZnTiO3 nanoparticles shifted from the UV region to the visible region. The photocatalytic activity of the La-doped ZnTiO3 nanoparticles was evaluated for the degradation of Rhodamine B under sunlight irradiation. The optimum photocatalytic activity was obtained for 2 atom% La-doped ZnTiO3, which is much higher than that of the non-doped ZnTiO3 as well as commercial N-TiO2. A possible mechanism for the degradation of Rhodamine B over La-doped ZnTiO3 was also discussed by trapping experiments. More importantly, the reusability of these nanoparticles is high. Hence La-doped ZnTiO3 nanoparticles can be used as efficient photocatalysts for environmental applications.

Synthesis of Cr and La-codoped SrTiO3 nanoparticles for enhanced photocatalytic performance under sunlight irradiation

In this study, we report a facile polymeric citrate strategy for the synthesis of Cr,La-codoped SrTiO3 nanoparticles. The synthesized samples were well characterized by various analytical techniques. The UV-vis DRS studies reveal that the absorption edge shifts towards the visible light region after doping with Cr, which is highly beneficial for absorbing the visible light in the solar spectrum. More attractively, codoping with La exhibits greatly enhanced photocatalytic activity for the degradation of Rhodamine B under sunlight irradiation. The optimum photocatalytic activity at 1 atom% of Cr,La-codoped SrTiO3 nanoparticles is almost 6 times higher than that of pure SrTiO3 nanoparticles and 3 times higher than that of Cr-doped SrTiO3 nanoparticles. The high photocatalytic performance in the present photocatalytic system is due to codoping with La, which acts as a most effective donor for stabilizing Cr3+ in Cr,La-codoped SrTiO3 nanoparticles. More importantly, the synthesized photocatalysts possess high reusability. A proposed mechanism for the enhanced photocatalytic activity of Cr,La-codoped SrTiO3 nanoparticles was also investigated by trapping experiments. Therefore, our results not only demonstrate the highly efficient visible light photocatalytic activity of the Cr,La-codoped SrTiO3 photocatalyst, but also enlighten the codoping strategy in the design and development of advanced photocatalytic materials for energy and environmental applications.

Distributed Genetic Algorithm Implementation by Means of Remote Methods Invocation Technique – Java RMI

The aim of this work is distributed genetic algorithm implementation (so called island algorithm) to accelerate the optimum searching process in space of solutions. Distributed genetic algorithm has also smaller chances to fall in local optimum. This conception depends on mutual cooperation of the clients which realize separate working of genetic algorithms on local machines. As a tool for implementation of distributed genetic algorithm, created to produce net's applications Java technology was chosen. In Java technology, there is a technique of remote methods invocation - Java RMI. By means of invoking remote methods it can send objects between clients and server RMI.

Using Inside-Outside Algorithm for Estimation of the Offspring Distribution in Multitype Branching Processes

Multitype branching processes (MTBP) model branching structures, where the nodes of the resulting tree are particles of different types. Usually such a process is not observable in the sense of the whole tree, but only as the “generation” at a given moment in time, which consists of the number of particles of every type. This requires an EM-type algorithm to obtain a maximum likelihood (ML) estimate of the parameters of the branching process. Using a version of the inside-outside algorithm for stochastic context-free grammars (SCFG), such an estimate could be obtained for the offspring distribution of the process.

A novel algorithm of posture best fit based on key characteristics for large components assembly

Measurement and variation control of geometrical Key Characteristics (KCs), such as flatness and gap of joint faces, coaxiality of cabin sections, is the crucial issue in large components assembly from the aerospace industry. Aiming to control geometrical KCs and to attain the best fit of posture, an optimization algorithm based on KCs for large components assembly is proposed. This approach regards the posture best fit, which is a key activity in Measurement Aided Assembly (MAA), as a two-phase optimal problem. In the first phase, the global measurement coordinate system of digital model and shop floor is unified with minimum error based on singular value decomposition, and the current posture of components being assembly is optimally solved in terms of minimum variation of all reference points. In the second phase, the best posture of the movable component is optimally determined by minimizing multiple KCs' variation with the constraints that every KC respectively conforms to its product specification. The optimal models and the process procedures for these two-phase optimal problems based on Particle Swarm Optimization (PSO) are proposed. In each model, every posture to be calculated is modeled as a 6 dimensional particle (three movement and three rotation parameters). Finally, an example that two cabin sections of satellite mainframe structure are being assembled is selected to verify the effectiveness of the proposed approach, models and algorithms. The experiment result shows the approach is promising and will provide a foundation for further study and application. © 2013 The Authors.

An Adaptation of the Hoshen-Kopelman Cluster Counting Algorithm for Honeycomb Networks

We develop a simplified implementation of the Hoshen-Kopelman cluster counting algorithm adapted for honeycomb networks. In our implementation of the algorithm we assume that all nodes in the network are occupied and links between nodes can be intact or broken. The algorithm counts how many clusters there are in the network and determines which nodes belong to each cluster. The network information is stored into two sets of data. The first one is related to the connectivity of the nodes and the second one to the state of links. The algorithm finds all clusters in only one scan across the network and thereafter cluster relabeling operates on a vector whose size is much smaller than the size of the network. Counting the number of clusters of each size, the algorithm determines the cluster size probability distribution from which the mean cluster size parameter can be estimated. Although our implementation of the Hoshen-Kopelman algorithm works only for networks with a honeycomb (hexagonal) structure, it can be easily changed to be applied for networks with arbitrary connectivity between the nodes (triangular, square, etc.). The proposed adaptation of the Hoshen-Kopelman cluster counting algorithm is applied to studying the thermal degradation of a graphene-like honeycomb membrane by means of Molecular Dynamics simulation with a Langevin thermostat. ACM Computing Classification System (1998): F.2.2, I.5.3.

Inmanencia mistica en la obra de Federico Garcia Lorca

The purpose of this dissertation was to analyze the works of Federico García Lorca within the mystic context that dominates their very genesis. The problematic definition of mysticism was explored lest it be confused with traditional mysticism, which implies union with the divine. The historiography of literature speaks of the Mystic Genre, yet it does not address the mystic mode of artistic creation due to its inability to adhere to rational measure. This mode of conception was explored through Lorca's poetic discourse: ‘Lorquian mysticism’ is the result of the poet's cultivation of an innate spiritual potential enhanced by external influences and technical mastery. ^ There is visible influence of Fray Luis of León in Lorca's early Libro de poemas and El maleficio de la mariposa, as well as of Saint John of the Cross in the later Diván del Tamarit, Sonetos de amor and Yerma. However, definitive echoes of poets from the Sufi and other Eastern mystic traditions were also illustrated in these late works. A persistent longing to elide the physical condition, the greatest obstacle of the transcendental quest, is the essence of Lorca's poetic voice. ^ The object of this analysis was Lorca's language, which reaches levels removed from conventional thought. His dazzling metaphors and his particular use of symbols and of paradox compare equitably with those of great mystic poets. Like them, Lorca was faced with the same limitations of language to describe an ineffable experience; he embraced what Octavio Paz describes as ‘sacred language’: there is a linguistic frugality as well as an ambiguity in Lorca's poetic art that result from his realization of supercognitive states. Yet such an interpretation is rejected by the rationalist approach, invoking the age-old debate between faith and reason and signaling the application of psychoanalytical theory. This limited approach was disputed on the basis of reader-response theory. Lorca was truly an eclectic and a modification of the conventional reader's preestablished horizon of expectations is essential in order to seal the gaps in his late works. This innovative perspective placed Lorca within the framework of a new mysticism in the modern world. ^

Elemental analysis and forensic comparison of soils by laser-induced breakdown spectroscopy (LIBS) and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS)

The elemental analysis of soil is useful in forensic and environmental sciences. Methods were developed and optimized for two laser-based multi-element analysis techniques: laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) and laser-induced breakdown spectroscopy (LIBS). This work represents the first use of a 266 nm laser for forensic soil analysis by LIBS. Sample preparation methods were developed and optimized for a variety of sample types, including pellets for large bulk soil specimens (470 mg) and sediment-laden filters (47 mg), and tape-mounting for small transfer evidence specimens (10 mg). Analytical performance for sediment filter pellets and tape-mounted soils was similar to that achieved with bulk pellets. An inter-laboratory comparison exercise was designed to evaluate the performance of the LA-ICP-MS and LIBS methods, as well as for micro X-ray fluorescence (μXRF), across multiple laboratories. Limits of detection (LODs) were 0.01-23 ppm for LA-ICP-MS, 0.25-574 ppm for LIBS, 16-4400 ppm for μXRF, and well below the levels normally seen in soils. Good intra-laboratory precision (≤ 6 % relative standard deviation (RSD) for LA-ICP-MS; ≤ 8 % for μXRF; ≤ 17 % for LIBS) and inter-laboratory precision (≤ 19 % for LA-ICP-MS; ≤ 25 % for μXRF) were achieved for most elements, which is encouraging for a first inter-laboratory exercise. While LIBS generally has higher LODs and RSDs than LA-ICP-MS, both were capable of generating good quality multi-element data sufficient for discrimination purposes. Multivariate methods using principal components analysis (PCA) and linear discriminant analysis (LDA) were developed for discriminations of soils from different sources. Specimens from different sites that were indistinguishable by color alone were discriminated by elemental analysis. Correct classification rates of 94.5 % or better were achieved in a simulated forensic discrimination of three similar sites for both LIBS and LA-ICP-MS. Results for tape-mounted specimens were nearly identical to those achieved with pellets. Methods were tested on soils from USA, Canada and Tanzania. Within-site heterogeneity was site-specific. Elemental differences were greatest for specimens separated by large distances, even within the same lithology. Elemental profiles can be used to discriminate soils from different locations and narrow down locations even when mineralogy is similar.

Self-tuning algorithm for dsp-based motion control in cnc applications

This thesis describes the development of an adaptive control algorithm for Computerized Numerical Control (CNC) machines implemented in a multi-axis motion control board based on the TMS320C31 DSP chip. The adaptive process involves two stages: Plant Modeling and Inverse Control Application. The first stage builds a non-recursive model of the CNC system (plant) using the Least-Mean-Square (LMS) algorithm. The second stage consists of the definition of a recursive structure (the controller) that implements an inverse model of the plant by using the coefficients of the model in an algorithm called Forward-Time Calculation (FTC). In this way, when the inverse controller is implemented in series with the plant, it will pre-compensate for the modification that the original plant introduces in the input signal. The performance of this solution was verified at three different levels: Software simulation, implementation in a set of isolated motor-encoder pairs and implementation in a real CNC machine. The use of the adaptive inverse controller effectively improved the step response of the system in all three levels. In the simulation, an ideal response was obtained. In the motor-encoder test, the rise time was reduced by as much as 80%, without overshoot, in some cases. Even with the larger mass of the actual CNC machine, decrease of the rise time and elimination of the overshoot were obtained in most cases. These results lead to the conclusion that the adaptive inverse controller is a viable approach to position control in CNC machinery.

Data compilation on the biological response to ocean acidification: environmental and experimental context of data sets and related literature

The exponential growth of studies on the biological response to ocean acidification over the last few decades has generated a large amount of data. To facilitate data comparison, a data compilation hosted at the data publisher PANGAEA was initiated in 2008 and is updated on a regular basis (doi:10.1594/PANGAEA.149999). By January 2015, a total of 581 data sets (over 4 000 000 data points) from 539 papers had been archived. Here we present the developments of this data compilation five years since its first description by Nisumaa et al. (2010). Most of study sites from which data archived are still in the Northern Hemisphere and the number of archived data from studies from the Southern Hemisphere and polar oceans are still relatively low. Data from 60 studies that investigated the response of a mix of organisms or natural communities were all added after 2010, indicating a welcomed shift from the study of individual organisms to communities and ecosystems. The initial imbalance of considerably more data archived on calcification and primary production than on other processes has improved. There is also a clear tendency towards more data archived from multifactorial studies after 2010. For easier and more effective access to ocean acidification data, the ocean acidification community is strongly encouraged to contribute to the data archiving effort, and help develop standard vocabularies describing the variables and define best practices for archiving ocean acidification data.

Primary data sets of the hydrographic atlas of the Southern Ocean

The general knowledge of the hydrographic structure of the Southern Ocean is still rather incomplete since observations particularly in the ice covered regions are cumbersome to be carried out. But we know from the available information that thermohaline processes have large amplitudes and cover a wide range of scales in this part of the world ocean. The modification of water masses around Antarctica have indeed a worldwide impact, these processes ultimately determine the cold state of the present climate in the world ocean. We have converted efforts of the German and Russian polar research institutions to collect and validate the presently available temperature, salinity and oxygen data of the ocean south of 30°S latitude. We have carried out this work in spite of the fact that the hydrographic programme of the World Ocean Circulation Experiment (WOCE) will provide more new information in due time, but its contribution to the high latitudes of the Southern Ocean is quite sparse. The modified picture of the hydrographic structure of the Southern Ocean presented in this atlas may serve the oceanographic community in many ways and help to unravel the role of this ocean in the global climate system. This atlas could only be prepared with the altruistic assistance of many colleagues from various institutions worldwide who have provided us with their data and their advice. Their generous help is gratefully acknowledged. During two years scientists from the Arctic and Antarctic Research Institute in St. Petersburg and the Alfred Wegener Institute for Polar and Marine Research in Bremerhaven have cooperated in a fruitful way to establish the atlas and the archive of about 38749 validated hydrographic stations. We hope that both sources of information will be widely applied for future ocean studies and will serve as a reference state for global change considerations.

Effects of vessel traffic on relative abundance and behaviour of cetaceans : the case of the bottlenose dolphins in the Archipelago de La Maddalena, north-western Mediterranean sea

Acknowledgements This study was part of the Tursiops Project of the Dolphin Research Centre of Caprera, La Maddalena. Financial and logistical support was provided by the Centro Turistico Studentesco (CTS) and by the National Park of the Archipelago de La Maddalena. We thank the Natural Reserve of Bocche di Bonifacio for the support provided during data collection. The authors thank the numerous volunteers of the Caprera Dolphin Research Centre and especially Marco Ferraro, Mirko Ugo, Angela Pira and Maurizio Piras whose assistance during field observation and skills as a boat driver were invaluable.

Étude des mécanismes d’extraction lipidique par le peptide mélittine et la protéine BSP1

Les peptides et protéines extracteurs de lipides (PEL) se lient aux membranes lipidiques puis en extraient des lipides en formant de plus petits auto-assemblages, un phénomène qui peut aller jusqu'à la fragmentation des membranes. Dans la nature, cette extraction se produit sur une gamme de cellules et entraîne des conséquences variées, comme la modification de la composition de la membrane et la mort de la cellule. Cette thèse se penche sur l’extraction lipidique, ou fragmentation, induite par le peptide mélittine et la protéine Binder-of-SPerm 1 (BSP1) sur des membranes lipidiques modèles. Pour ce faire, des liposomes de différentes compositions sont préparés et incubés avec la mélittine ou la BSP1. L'association aux membranes est déterminée par la fluorescence intrinsèque des PEL, tandis que l'extraction est caractérisée par une plateforme analytique combinant des tests colorimétriques et des analyses en chromatographie en phase liquide et spectrométrie de masse (LCMS). La mélittine fait partie des peptides antimicrobiens cationiques, un groupe de PEL très répandu chez les organismes vivants. Ces peptides sont intéressants du point du vue médical étant donné leur mode d’action qui vise directement les lipides des membranes. Plusieurs de ceux-ci agissent sur les membranes des bactéries selon le mécanisme dit « en tapis », par lequel ils s’adsorbent à leur surface, forment des pores et ultimement causent leur fragmentation. Dans cette thèse, la mélittine est utilisée comme peptide modèle afin d’étudier le mécanisme par lequel les peptides antimicrobiens cationiques fragmentent les membranes. Les résultats montrent que la fragmentation des membranes de phosphatidylcholines (PC) est réduite par une déméthylation graduelle de leur groupement ammonium. L'analyse du matériel fragmenté révèle que les PC sont préférentiellement extraites des membranes, dû à un enrichissement local en PC autour de la mélittine à l'intérieur de la membrane. De plus, un analogue de la mélittine, dont la majorité des résidus cationiques sont neutralisés, est utilisé pour évaluer le rôle du caractère cationique de la mélittine native. La neutralisation augmente l'affinité du peptide pour les membranes neutres et anioniques, réduit la fragmentation des membranes neutres et augmente la fragmentation des membranes anioniques. Malgré les interactions électrostatiques entre le peptide cationique et les lipides anioniques, aucune spécificité lipidique n'est observée dans l'extraction. La BSP1 est la protéine la plus abondante du liquide séminal bovin et constitue un autre exemple de PEL naturel important. Elle se mélange aux spermatozoïdes lors de l’éjaculation et extrait des lipides de leur membrane, notamment le cholestérol et les phosphatidylcholines. Cette étape cruciale modifie la composition lipidique de la membrane du spermatozoïde, ce qui faciliterait par la suite la fécondation de l’ovule. Cependant, le contact prolongé de la protéine avec les spermatozoïdes endommagerait la semence. Cette thèse cherche donc à approfondir notre compréhension de ce délicat phénomène en étudiant le mécanisme moléculaire par lequel la protéine fragmente les membranes lipidiques. Les résultats des présents travaux permettent de proposer un mécanisme d’extraction lipidique en 3 étapes : 1) L'association à l’interface des membranes; 2) La relocalisation de l’interface vers le cœur lipidique; 3) La fragmentation des membranes. La BSP1 se lie directement à deux PC à l'interface; une quantité suffisante de PC dans les membranes est nécessaire pour permettre l'association et la fragmentation. Cette liaison spécifique ne mène généralement pas à une extraction lipidique sélective. L'impact des insaturations des chaînes lipidiques, de la présence de lysophosphatidylcholines, de phosphatidyléthanolamine, de cholestérol et de lipides anioniques est également évalué. Les présentes observations soulignent la complexe relation entre l'affinité d'un PEL pour une membrane et le niveau de fragmentation qu'il induit. L'importance de la relocalisation des PEL de l'interface vers le cœur hydrophobe des membranes pour permettre leur fragmentation est réitérée. Cette fragmentation semble s'accompagner d'une extraction lipidique préférentielle seulement lorsqu'une séparation de phase est induite au niveau de la membrane, nonobstant les interactions spécifiques PEL-lipide. Les prévalences des structures amphiphiles chez certains PEL, ainsi que de la fragmentation en auto-assemblages discoïdaux sont discutées. Finalement, le rôle des interactions électrostatiques entre les peptides antimicrobiens cationiques et les membranes bactériennes anioniques est nuancé : les résidus chargés diminueraient l'association des peptides aux membranes neutres suite à l'augmentation de leur énergie de solvatation.