The Role of Structural Imperfections in Sr2FeMoO6 Thin Films

In this work, Sr2FeMoO6 (SFMO) thin films were studied with the main focus on their magnetic and magneto-transport properties. The fabrication process of pulsed laser deposited SFMO films was first optimized. Then the effects of strain, film thickness and substrate were thoroughly investigated. In addition to these external factors, the effect of intrinsic defects on the magnetic properties of SFMO were also clarified. Secondly, the magnetoresistivity mechanims of SFMO films were studied and a semiempirical model of the temperature dependence of resistivity was introduced. The films were grown on single crystal substrates using a ceramic target made with sol-gel method. The structural characterization of the films were carried out with X-ray diffraction, atomic force microscopy, transmission electron microscopy and high kinetic energy photoelectron spectroscopy. The magnetic properties were measured with SQUID magnetometer and the magneto-transport properties by magnetometer with a resistivity option. SFMO films with the best combination of structural and magnetic properties were grown in Ar atmosphere at 1050 °C . Their magnetic properties could not be improved by the ex situ post-annealing treatments aside from the treatments in ultra-high vacuum conditions. The optimal film thickness was found to be around 150 nm and only small improvement in the magnetic properties with decreasing strain was observed. Instead, the magnetic properties were observed to be highly dependent on the choice of the substrate due to the lattice mismatch induced defects, which are best avoided by using the SrTiO3 substrate. The large difference in the Curie temperature and the saturation magnetization between the SFMO thin film and polycrystalline bulk samples was connected to the antisite disorder and oxygen vacancies. Thus, the Curie temperature of SFMO thin films could be improved by increasing the amount of oxygen vacancies for example with ultra-high vacuum treatments or improving the B-site ordering by further optimization of the deposition parameters. The magneto-transport properties of SFMO thin films do not follow any conventional models, but the temperature dependence of resistivity was succesfully described with a model of two spin channel system. Also, evidences that the resistivity-temperature behaviour of SFMO thin films is dominated by the structural defects, which reduce the band gap in the majority spin band were found. Moreover, the magnetic field response of the resistivity in SFMO thin films were found to be superposition of different mechanisms that seems to be related to the structural changes in the film.

Sequence-characterized amplified region (SCAR) technique used for variety discrimination in vinca (Catharanthus roseus (L.) G.Don)

Sequence-Characterized Amplified Region (SCAR) appears as a useful technique for genetic purity testing and variety discrimination, applicable to species in which some other techniques have failed. In particular, this technique is very attractive with species in which RAPD results were not consistent. The RAPD polymorphic bands were cloned, sequenced and from the sequence information, primers pairs for normal PCR were developed. Since the probability of obtaining successful SCAR primers from RAPD polymorphic bands was about 50%, a larger number of RAPD polymorphic bands are needed to develop sufficient SCAR primers for varietal discrimination in vinca. In addition, the efficiency of the SCAR technique is strongly affected by the quality of DNA extracted from seeds. The SCAR banding patterns obtained from vinca seed were consistent and repeatable making the results reliable for genetic purity testing and variety discrimination. The SCAR technique is simple, fast, relatively inexpensive and allows the use of DNA extracted from dry seeds, which is very important in a seed-quality evaluating program

Synthesis and characterization of nanoperforated metal oxide thin films

For advanced devices in the application fields of data storage, solar cell and biosensing, one of the major challenges to achieve high efficiency is the fabrication of nanopatterned metal oxide surfaces. Such surfaces often require both precise structure at the nanometer scale and controllable patterned structure at the macro scale. Nowadays, the dominating candidates to fabricate nanopatterned surfaces are the lithographic technique and block-copolymer masks, most of which are unfortunately costly and inefficient. An alternative bottom-up approach, which involves organic/inorganic self-assembly and dip-coating deposition, has been studied intensively in recent years and has proven to be an effective technique for the fabrication of nanoperforated metal oxide thin films. The overall objective of this work was to optimize the synthesis conditions of nanoperforated TiO2 (NP-TiO2) thin films, especially to be compatible with mixed metal oxide systems. Another goal was to develop fabrication and processing of NP-TiO2 thin films towards largescale production and seek new applications for solar cells and biosensing. Besides the traditional dip-coating and drop-casting methods, inkjet printing was used to prepare thin films of metal oxides, with the advantage of depositing the ink onto target areas, further enabling cost-effective fabrication of micro-patterned nanoperforated metal oxide thin films. The films were characterized by water contact angle determination, Atomic Force Microscopy, Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy and Grazing Incidence XRay Diffraction. In this study, well-ordered zinc titanate nanoperforated thin films with different Zn/Ti ratios were produced successfully with zinc precursor content up to 50 mol%, and the dominating phase was Zn2Ti3O8. NP-TiO2 structures were also obtained by a cost-efficient means, namely inkjet printing, at both ambient temperature and 60 °C. To further explore new biosensing applications of nanoperforated oxide thin films, inkjet printing was used for the fabrication of both continuous and patterned polymeric films onto NP-TiO2 and perfluorinated phosphate functionalized NP-TiO2 substrates, respectively. The NP-TiO2 films can be also functionalized with a fluoroalkylsilane, resulting in hydrophobic surfaces on both titania and silica. The surface energy contrast in the nanoperforations can be tuned by irradiating the films with UV light, which provides ideal model systems for wettability studies.

Probing MST1 Kinase Sequence and Structure for Rational Drug Discovery (Targeting diabetes by blocking protein-protein interactions)

Apoptotic beta cell death is an underlying cause majorly for type I and to a lesser extent for type II diabetes. Recently, MST1 kinase was identified as a key apoptotic agent in diabetic condition. In this study, I have examined MST1 and closely related kinases namely, MST2, MST3 and MST4, aiming to tackle diabetes by exploring ways to selectively block MST1 kinase activity. The first investigation was directed towards evaluating possibilities of selectively blocking the ATP binding site of MST1 kinase that is essential for the activity of the enzymes. Structure and sequence analyses of this site however revealed a near absolute conservation between the MSTs and very few changes with other kinases. The observed residue variations also displayed similar physicochemical properties making it hard for selective inhibition of the enzyme. Second, possibilities for allosteric inhibition of the enzyme were evaluated. Analysis of the recognized allosteric site also posed the same problem as the MSTs shared almost all of the same residues. The third analysis was made on the SARAH domain, which is required for the dimerization and activation of MST1 and MST2 kinases. MST3 and MST4 lack this domain, hence selectivity against these two kinases can be achieved. Other proteins with SARAH domains such as the RASSF proteins were also examined. Their interaction with the MST1 SARAH domain were evaluated to mimic their binding pattern and design a peptide inhibitor that interferes with MST1 SARAH dimerization. In molecular simulations the RASSF5 SARAH domain was shown to strongly interact with the MST1 SARAH domain and possibly preventing MST1 SARAH dimerization. Based on this, the peptidic inhibitor was suggested to be based on the sequence of RASSF5 SARAH domain. Since the MST2 kinase also interacts with RASSF5 SARAH domain, absolute selectivity might not be achieved.

Study of colossal magnetoresistance and pressure effects in La2/3Ca1/3MnO2 thin films /

The main purpose of this thesis is to study properties of La2/3Cai/3Mn03, both polycrystalline ceramics and thin films. This material has striking related electrical and magnetic properties. Thin films show colossal negative magnetoresistance (CMR) near transition from an insulating to a metallic state accompanied closely by transition from a paramagnetic to a ferromagnetic state. The double exchange mechanism (DE) and the Jahn-Teller deformations play an important role in CMR effect. Applied pressure has a very similar effect as does an applied magnetic field, except, at low temperatures (Tthin films by pulsed laser deposition was successfully developed. The films grown on (100) SrTiOs substrate are c-axis oriented and exhibit negative magnetoresistance Ap/p(H) of over 400% at 245°C and 4200% at 90 K.

Systematic studies of the effect of pressure on magnetic and electronic properties of La2/3Ca1/3MnO3 thin films with various thicknesses /

Interest in mixed-valent perovskite manganese oxides of La\-xAxMnO^ (v4-divalent alkaline earth Ca, Sr or Ba), whose unusual properties were discovered nearly a half century ago, has recently been revived. The discovery of the colossal magnetoresistance and pressure effects introduced new questions concerning the complex interplay between lattice structure, magnetism and transport in doped perovskite manganites. In this study, we report our experimental investigations of pressure and magnetic field dependencies of La-i/sCai/sMnOs (LCMO) epitaxial films with various thickness on SrTiO$ substrate. An analysis of film thickness dependency of the resistivity of LCMO epitaxial films under pressure and magnetic field has been performed by taking into account substrate contributions. This verifies the correlation of lattice distortion with magnetic and transport properties. Strong dependencies of Mn — O — Mn bond bending and Mn — O bond stretching with pressure as well as Mn spin alignment with magnetic field, and the lattice distortion induced by the substrate are discussed.

Infrared spectroscopy of Mg-doped SrRuO3 thin films /

The reflectance of thin films of magnesium doped SrRu03(Mg-SR0) produced by pulsed laser deposition on SrTiOa (100) substrates has been measured at room temperature between 100 and 7500 cm~^. The films were chosen to have wide range of thickness, stoichiometry and electrical properties. As the films were very thin (less than 300 nm), and some were insulating the reflectance data shows structures due to both the film and the substrate. Hence, the data was analyzed using Kramers-Kronig constrained variational fitting (VDF) method to extract the real optical conductivity of the Mg-SRO films. Although the VDF technique is flexible enough to fit all features of the reflectance spectra, it seems that VDF could not eliminate the substrate's contribution from fllm conductivity results. Also the comparison of the two different programs implementing VDF fltting shows that this technique has a uniqueness problem. The optical properties are discussed in light of the measured structural and transport properties of the fllms which vary with preparation conditions and can be correlated with differences in stoichiometry. This investigation was aimed at checking the VDF technique and also getting answer to the question whether Mg^"*" substitutes in to Ru or Sr site. Analysis of our data suggests that Mg^+ goes to Ru site.

A reconnaissance study of the metamorphic petrology and volcanic geochemistry of a portion of the Island Lake greenstone belt, Manitoba /

The Island Lake greenstone belt is one of the major Archean supracrustal exposures in the northwestern part of the Superior Province of the Canadian Shield. This belt is subdivided into two units: 1) a lower sequence characterised by pillowed to massive, locally pyroclastic, basalt to andesite with a thin central zone of felsic derivatives, all of which are interbedded with and overlain by thick sequences of turbidite facies rock; 2) the upper unit which consists of thick stratified conglomerate overlain by thickly bedded arkose and feldspathic greywacke. Reconnaissance sampling traverses were completed across both the strike of the belt and along its margins with adjacent granitoids. Most of the belt is within the greenschist metamorphic f acies with amphibolite facies occurring in certain areas near t he margins. A post-tectonic, low pressure thermal event may be responsible for the development of a unit of cordierite schi s t which stretches southeastwards from the east end of Cochrane Bay. Volcanism is cyclical in nature changing from tholeiitic to calc-alkaline. There is a general progression in the character of the lavas from mafic t o felsic with stratigraphic height. Chemica l d a ta sugges t that h i gh level fractionation of a mantle- derived ' dry' magma i s t he s ource of the thole i iti c lavas. Contamination of this magma with 'we t' sia l and subsequent fractionation may be r esponsi b l e for the calcalkaline phases .Observations of stratigraphic relationships (in particular the contact between the supracrustals and the granitoids) coupled with the metamorphic and chemical studies, allow the construction of a preliminary model for the evolution of the Island Lake greenstone belt. The following sequential development is suggested: 1) a platform stage characterised by the subaqueous effusion of mafic to intermediate lavas of alternating tholeiitic and calc-alkaline affinities; 2) an edifice stage marked by the eruption of felsic calc-alkaline rocks; 3) an erosional stage characterised by the deposit~on of thick sequences of turbidite facies rocks; 4) the impingement of granitic masses into the margins of the greenstone belt, which was probably related to a downward warping of the supracrustal pilei 5) the erosion of sialic massifs surrounding and within the greenstone belt and of early supracrustal piles, to give the clastic upper unit.

Composition analysis of high-Tc superconducting thin films by quantitative x-ray fluorescence

A method is presented for determining the composition of thin films containing the elements Bi, Sr, Br, Cu, and Ca. Quantitative x-ray fluorescence (XRF) consisting of radioactive sources (secondary foil excitor 241Am-Mo source and 55Pe source), a Si(Li) detector, and a multichannel analyzer were employed. The XRF system was calibrated by using sol gel thin films of known element composition and also by sputtered thin films analyzed by the conventional Rutherford Back Scattering (RBS). The XRF system has been used to assist and optimize the sputter target composition required to produce high-Tc BiSrCaCuO films with the desired metal composition.

Geological image processing of petrographic thin sections using the rotating polarizer stage

One of the fundamental problems with image processing of petrographic thin sections is that the appearance (colour I intensity) of a mineral grain will vary with the orientation of the crystal lattice to the preferred direction of the polarizing filters on a petrographic microscope. This makes it very difficult to determine grain boundaries, grain orientation and mineral species from a single captured image. To overcome this problem, the Rotating Polarizer Stage was used to replace the fixed polarizer and analyzer on a standard petrographic microscope. The Rotating Polarizer Stage rotates the polarizers while the thin section remains stationary, allowing for better data gathering possibilities. Instead of capturing a single image of a thin section, six composite data sets are created by rotating the polarizers through 900 (or 1800 if quartz c-axes measurements need to be taken) in both plane and cross polarized light. The composite data sets can be viewed as separate images and consist of the average intensity image, the maximum intensity image, the minimum intensity image, the maximum position image, the minimum position image and the gradient image. The overall strategy used by the image processing system is to gather the composite data sets, determine the grain boundaries using the gradient image, classify the different mineral species present using the minimum and maximum intensity images and then perform measurements of grain shape and, where possible, partial crystallographic orientation using the maximum intensity and maximum position images.

Preparation of SrMgx-Ru1-xO3 thin films by pulsed laser deposition /

SrMg^Rui-iOa thin films were made by using pulsed laser deposition on SrTiOa (100) substrates in either O2 or Ar atmosphere. The thin films were characterized by x-ray diffraction, energy dispersive x-ray microanalysis, dc resistivity measurement, and dc magnetization measurement. The effect of Mg doping was observed. As soon as the amount of Mg increased in SrMg-cRui-iOa thin films, the magnetization decreased, and the resistivity increased. It had little effect on the Curie temperature (transition temperature). The magnetization states of SrMgiRui-iOa thin films, for x < 0.15, are similar to SrRuOs films. X-ray diffraction results for SrMga-Rui-iOa thin films made in oxygen showed that the films are epitaxial. The thin films could not be well made in Ar atmosphere during laser ablation as there was no clear peak of SrMg^Rui-iOa in x-ray diffraction results. Substrate temperatures had an effect on the resistivity of the films. The residual resistivity ratios were increased by increasing substrate temperature. It was observed that the thickness of thin films are another factor for film quality: Thin films were epitaxial, but thicker films were not epitaxial.

Improving Short DNA Sequence Alignment with Parallel Computing

Variations in different types of genomes have been found to be responsible for a large degree of physical diversity such as appearance and susceptibility to disease. Identification of genomic variations is difficult and can be facilitated through computational analysis of DNA sequences. Newly available technologies are able to sequence billions of DNA base pairs relatively quickly. These sequences can be used to identify variations within their specific genome but must be mapped to a reference sequence first. In order to align these sequences to a reference sequence, we require mapping algorithms that make use of approximate string matching and string indexing methods. To date, few mapping algorithms have been tailored to handle the massive amounts of output generated by newly available sequencing technologies. In otrder to handle this large amount of data, we modified the popular mapping software BWA to run in parallel using OpenMPI. Parallel BWA matches the efficiency of multithreaded BWA functions while providing efficient parallelism for BWA functions that do not currently support multithreading. Parallel BWA shows significant wall time speedup in comparison to multithreaded BWA on high-performance computing clusters, and will thus facilitate the analysis of genome sequencing data.

THE ASSOCIATION OF SEQUENCE OF HIRING PRACTICE AND BIOPHYSICAL COMPONENTS IN SCREENING PROBATIONARY FIREFIGHTERS

Variation in hiring procedures occurs within fire service human resource departments. In this study, City 1 and City 2 applicants were required to pass their biophysical assessments prior to being hired as firefighters at the beginning and end of the screening process, respectively. City 1 applicants demonstrated significantly lower resting heart rate (RHR), resting diastolic blood pressure (RDBP), body fat% (BF) and higher z-scores for BF, trunk flexibility (TF) and overall clinical assessment (p<0.05). Regression analysis found that age and conducting the biophysical assessment at the end of the screening process explained poorer biophysical assessment results in BF% (R2=21%), BF z-score (R2=22%), TF z-score (R2=10%) and overall clinical assessment z-score (R2=7%). Each of RHR (OR=1.06, CI=1.01-1.10), RDBP (OR=1.05, CI=1.00-1.11) and BF% (OR=1.20, CI=1.07-1.37) increased the odds of being a City 2 firefighter (p<0.05). Biophysical screening at the end of the hiring process may result in the hiring of a less healthy firefighter.

Complete Genome Sequence of Erwinia amylovora Bacteriophage

The complete genome of an Erwinia amylovora bacteriophage, vB_EamM_Ea35-70 (Ea35-70), is 271,084 bp, encodes 318 putative proteins, and contains one tRNA. Comparative analysis with other Myoviridae genomes suggests that Ea35-70 is related to the Phikzlikevirus genus within the family Myoviridae, since 26% of Ea35-70 proteins share homology to proteins in Pseudomonas phage φKZ.

HG 186.15-186.25 Thin Section

Coarse grained sample with multiple fine grained domains. Clasts range from small to medium and sub-angular to sub-rounded. Mainly contains grain crushing (with grains crushed into one another) and short distance lineations. A few rotation structures are seen and fine grained sand domains can also be seen.