Influência da energia de soldagem em uniões de lâminas finas através de laser pulsado de Nd:YAG

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Geochronology of the lpanema layered mafic-ultramafic complex, Minas gerais, Brazil: Evidence of extension at the meso-neoproterozoic time boundary

The mafic/ultramafic Ipanema Layered Complex (ILC), Minas Gerais Brazil, consists of seven individual bodies. These units crosscut polyphase orthogneisses and interlayered paragneisses of the Paleoproterozoic Juiz de Fora Complex. Intrusive granitoids tectonically related to [lie Neoproterozoie Aracuai orogen are also present in the study area.A Sm-Nd whole-rock linear array for seven samples metapyoxenites, metaperidotiles, metagabbro. and meta-anorthosite) from the Santa Cruz massif, the largest body of the ILC. suggest that it was emplaced at 1104 +/- 78 Ma the original magma was derived from a depleted mantle source (epsilon(Ndt)= +3.8). U-Pb single-grain zircon stud of a meta-anorthosite yields all upper intercept age of 1719 +/- 4 Ma, which is interpreted to represent inheritance. The lower intercept at 630+/-3 Ma indicates (hat a Neoproterozoic tectonothermal episode overprinted the ILC, this event occurred under upper-amphiolite-, to granulite-facies conditions. The 630 Ma episode is consistent with the timing of regional metamorphism and deformation of the adjacent Aracuai orogen (Brasiliano collage). Emplacement of the ILC and other coeval metamafies and meta-ultramafics (of alkaline affinity) in the re, oil is attributed to early extension tectonics, accompanying accretion of the Rodinia super- continent during the Mesoproterozoic-Neoproterozoic time boundary.

Puberty and growth rate in thoroughbred fillies

We measured progesterone and estradiol levels from birth to the beginning of adult life in 10 Thoroughbred fillies from the Equilia Stud Farm in Avare SP, Brasil. The animals were measured and weighed monthly for the determination of body development and of a possible correlation between the rate of weight and height gain and the onset of detectable sex hormone levels. Jugular blood was collected twice a week and stored at -20 degrees C until assay of progesterone by a solid phase RIA with a sensitivity of 0.32 nmol/L and of estradiol by liquid phase RIA adapted to low levels (3.67 pmol/L). The fillies were born with high serum levels of both hormones,which fell to undetectable levels by the first week of life. A variation in growth rate was observed, with the highest levels occuring from birth to the 3rd month of life, followed by a reduction until 15 mo of life, when fast growth was resumed. The monthly weight gain was 1.5% when the fillies reached puberty and 5.4% during the next month, (P<0.05, Friedman test). During this second period of accelerated growth after the beginning of progesterone production at detectable levels (above 0.318 nmol/L), the parameters of skeletal growth did not differ (P>0.05). The month of onset of puberty was the month of lowest weight gain in the life of the fillies, and it coincided with the highest insolation period. In conclusion, horses, like all other developed vertebrates, have a double pattern of development, with the acceleration observed at puberty depending on sex steroids, which in turn coincides with the highest insolation period. Gonadal activity characterized by serum progesterone levels was low from birth to the onset of puberty. After puberty the progesterone cycles were similar to those of adult animals with a mature hypothalamic-gonadal axis. (C) 1997 by Elsevier B.V.

Estudo Comparativo de Juntas Soldadas a TIG e Laser Empregando-se Ti com Pureza Comercial Utilizado em Prótese sobre Implantes

Welding in the dentistry has been used for great part of the specialized dentist-surgeons in the implants area to solve prosthesis supported by implant adaptation problems. The development of new equipments Laser and TIG allowed a larger use of these processes in the prosthesis production. In this work, it was studied welded joints made by Laser and TIG, using commercial purity titanium, cpTi, applied in prosthesis supported by implants. The weld characterizations were carried out by light microscopy, EDS_elementary mapping, microhardness and tensile test. Through metallographic characterization, the weld bead presented a martensitic microstructure in the Laser welding process, originated from shear provoked by deformations in the lattice. This caused structural changes of the transformed area, which determines a fine plate-like morphology. In the weld bead from TIG, besides presenting higher hardness, was observed formation of Widmansttaten structure, which is characteristic of a geometric model, resulted of new phase formation along of the crystallographic plans. The martensitic structure is more refined than Widmansttaten structure, due to the high-speed cooling (10(3)degrees C/s) imposed by the Laser process.

Laser weld: microstructure and corrosion study of Ag-Pd-Au-Cu alloy of the dental application

The laser Welding process was introduced into dentistry by the end of the 1980s, resulting on a great impulse to that area with the development of cheaper and smaller equipment, using simpler technique. This allowed greater use of that process on the confection of prostheses compared to the brazing process since the heat source for that process is a concentrated light beam of high power, which minimizes distortion problems on the prosthetic pieces. Ag-Pd-Au-Cu alloy used on the confection of dental implant prostheses was observed before and after subjection to the laser welding process. The microstructure was analyzed with the. use of optic microscopy and the corrosion resistance was studied by the traditional electrochemical techniques and by electrochemical impedance, under environmental conditions simulating the aggressiveness found in the mouth cavity. A structural change was detected on the weld area, which presented a refined microstructure deriving from the high-speed cooling. The base metal out of the weld area presented a fusion coarse microstructure. The electrochemical essays showed differences on the potentiodynamic polarization behavior in both weld and metal base areas, indicating superior corrosion resistance in the weld area. The impedance spectra were characterized by capacitive distorted components, presenting linear impedance in the low frequencies area. (C) 2002 Elsevier B.V. B.V. All rights reserved.

Effects of a postweld heat treatment on a submerged arc welded ASTM A537 pressure vessel steel

Postweld heat treatment (PWHT) is frequently applied to steel pressure vessels, following the requirements of the ASME code (section VIII), which establishes the parameters of the PWHT based on the thickness and chemical composition of the welded section. This work shows the results of an analysis undertaken on a sample of ASTM A537 C1 steel subjected to qualifying welding procedure tests including PWHT (650 degreesC/5 h), the results obtained showed that this PWHT practice promoted a reduction in the mechanical properties of the base metal and the heat-affected zone (HAZ).

A REVIEW OF THE GENUS MEGAELOSIA (ANURA, LEPTODACTYLIDAE) WITH A DESCRIPTION OF A NEW SPECIES

A new species of Megaelosia is described from the Atlantic Forest in the northern part of São Paulo, southeastern Brazil. Based on examination of topotypic specimens of Megaelosia massarti, this species is removed from the synonymy of M. goeldii. Tadpoles of M. lutzae and M. massarti are described and natural history observations of M. massarti and M. goeldii are reported. Diagnoses, measurements, figures, distributional data, and a key for the species of Megaelosia are provided.

SAE 1045 steel/WC-Co/Ni-Cu-Ni/SAE 1045 steel joints prepared by dynamic diffusion bonding: Microelectrochemical studies in 0.6 M NaCl solution

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tensoes Residuais na Soldagem, Aspectos Basicos

The purpose of this paper is to analyze the basic aspects of the residual stresses in welding. Concepts about macro and micro residual stresses in metals are considered in welding. In a simple welding model is shown how shrinkage macro stress results and how this can contribute to understand the distribution of residual stresses in common type of welded joint. Further, comments are made concerning the effects of additional mechanical and metallurgical phenomena, distortion in weldments and dimensional discrepancies.

Design studies of the magnetic properties of structural materials affecting the magnetic field of high-homogeneity superconducting magnets

Austenitic stainless steel presents phase changes caused by heat treatment and welding processes. Because it represents a problem in the design of high-homogeneity magnets, we have been studying the magnetic properties of Ti alloys for their use instead of stainless steel as structural material for superconducting magnet construction. In this work, we present the comparative study of the influence of magnetic properties of steel and Ti alloys on the magnetic-field homogeneity of a superconducting coil through numerical calculation using the measured magnetic properties. © 2001 Elsevier Science B.V. All rights reserved.