Yielding of engineering polymers at strain rates of up to 500 s-1

A method is described for measuring the mechanical properties of polymers in compression at strain rates in the range approximately 300-500 s-1. A gravity-driven pendulum is used to load a specimen on the end of an instrumented Hopkinson output bar and the results are processed by a microcomputer. Stress-strain curves up to high strains are presented for polycarbonate, polyethersulphone and high density polyethylene over a range of temperatures. The value of yield stress, for all three polymers, was found to vary linearly with log (strain rate) at strain rates up to 500 s-1. © 1985.

Analysis of the piston ring/liner oil film development during warm-up for an SI-engine

A one-dimensional ring-pack lubrication model developed at MIT is applied to simulate the oil film behavior during the warm-up period of a Kohler spark ignition engine [1]. This is done by making assumptions for the evolution of the oil temperatures during warm-up and that the oil control ring during downstrokes is fully flooded. The ring-pack lubrication model includes features such as three different lubrication regimes, i.e. pure hydrodynamic lubrication, boundary lubrication and pure asperity contact, non-steady wetting of both inlet and outlet of the piston ring, capability to use all ring face profiles that can be approximated by piece-wise polynomials and, finally, the ability to model the rheology of multi-grade oils. Not surprisingly, the simulations show that by far the most important parameter is the temperature dependence of the oil viscosity. This dependence is subsequently examined further by choosing different oils. The baseline oil is SAE 10W30 and results are compared to those using the SAE 30 and the SAE 10W50 oils.

Starting-up roadmapping fast

Technology roadmapping is a powerful technique for supporting technology management and planning in the firm. The roadmap enables the evolution of markets, products and technologies to be explored, together with the linkages between the various perspectives. A process called T-Plan, which has been developed to support the rapid initiation of roadmapping and thus address these challenges is described.

Statistical energy analysis of a built-up structure excited through its stiffening members

A new method of analysing high frequency vibrations in stiffened structures requires the calculation of a "power absorbing impedance matrix" for each plate in the system. The present paper is concerned with formulating this matrix by using point collocation in conjunction with basis functions representing incoming cylindrical waves. Key numerical issues are highlighted by considering the special case of a membrane, rather than a plate, and conclusions are made regarding the utility of the method.

A pilot scale set up for the manufacture of fish hydrolysate

This paper describes a set up for a pilot plant with a capacity of 50 kg raw material per batch for the production of fish hydrolysate by enzymatic hydrolysis. Process flow sheet and complete specifications and functions of individual equipment have been described. Multifunctional equipment designed for this pilot plant set up has reduced the number of equipment considerably.

High temperature processing of fish sausage 1. - An improved technique

An improved technique for the preparation of fish sausage (Nemipterus japonicus) over the conventional method (90°degree C for 1 h) has been evolved by processing at a temperature of 115.6°degree C (4.5 kg) for 20 min. The overall quality characteristics of fish sausage, particularly its colour, texture and appearance remained unchanged and the product was in good condition up to 9 days at ambient temperature in contrast to the shelf life of 3 days by conventional method. The design of the equipment used for the processing of fish sausage and the method of operation are described. The keeping quality of the product from an organoleptic stand point was also studied

The fundamental mechanism behind headbox jet break-up

It has previously been shown that MD streaks are created in the headbox jet, which is closely connected to the appearance of waves on the jet surface. The fundamental mechanism behind this break-up is presented. This has been achieved by implementing state-of-the-art methods for determining the characteristics and evolution of hydrody-namic instabilities. The methodology also allows the headbox slice to be designed in order to minimise jet break-up. This possibility has been evaluated in pilot-scale.

What's up on carp?

Bighead carp is preferred among other species for culture because of its fast growth and high survival rate. Pen and cage culture of carps in Laguna de Bay is sustained by the availability of juveniles as a result of improved hatchery technology. Southeast Asian Fisheries Development Center and the Bureau of Fisheries and Aquatic Resources have been conducting research programs to enhance the carp culture industry in the country.

Run-up of solitary waves on twin conical islands using a boussinesq model

This paper investigates the interaction of solitary waves (representative of tsunamis) with idealized flat-topped conical islands. The investigation is based on simulations produced by a numerical model that solves the two-dimensional Boussinesq-type equations of Madsen and Sørensen using a total variation diminishing Lax-Wendroff scheme. After verification against published laboratory data on solitary wave run-up at a single island, the numerical model is applied to study the maximum run-up at a pair of identical conical islands located at different spacings apart for various angles of wave attack. The predicted results indicate that the maximum run-up can be attenuated or enhanced according to the position of the second island because of wave refraction, diffraction, and reflection. It is also observed that the local wave height and hence run-up can be amplified at certain gap spacing between the islands, owing to the interference between the incident waves and the reflected waves between islands. © 2012 American Society of Mechanical Engineers.